| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Put a small comment before assigning IRQ_WAKE_THREAD
telling us what is going on.
Cc: Russell King <linux@armlinux.org.uk>
Cc: Yann Gautier <yann.gautier@foss.st.com>
Cc: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210921143359.1738149-1-linus.walleij@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
ADMA is only available on controller instances that are connected to the
L3 interconnect and are bus mastering capable.
As the MMCHS_HL_HWINFO is in the module registers before omap registers
and sdhci registers, and the omap registers and sdhci registers can be
at different offsets depending on the SoC, let's read MMCHS_HL_HWINFO
directly.
Let's also switch to using device_property_present() while at it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210921110029.21944-6-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
We need to support the legacy ti,non-removable property too. Let's warn
about the legacy property and mark the device as non-removable.
Naturally all the mainline kernel devicetree files will get updated to use
the standard non-removable property with the sdhci-omap conversion. But we
also have folks updating their kernels with custom devicetree files that
we need to consider.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210921110029.21944-5-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The sysconfig register is managed in a generic way by PM runtime for us by
the interconnect target module layer code. SDHCI_RESET_ALL also resets the
target module configuration, so we need to restore sysconfig after reset.
Note that there is no need to save and restore sysconfig during PM runtime,
the PM runtime layer will do that for us.
Not sure if this issue is a problem with the current configurations, I
noticed the issue while adding support for older TI SoCs and testing with
wlcore SDIO wlan device.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210921110029.21944-4-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
We need to restore context in a specified order with HCTL set in two
phases. This is similar to what omap_hsmmc_context_restore() is doing.
Otherwise SDIO can stop working on resume.
And for PM runtime and SDIO cards, we need to also save SYSCTL, IE and
ISE.
This should not be a problem currently, and these patches can be applied
whenever suitable.
Fixes: ee0f309263a6 ("mmc: sdhci-omap: Add Support for Suspend/Resume")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210921110029.21944-3-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
If sdhci-omap is configured for an unused device instance and the device
is not set as disabled, we can get a NULL pointer dereference:
Unable to handle kernel NULL pointer dereference at virtual address
00000045
...
(regulator_set_voltage) from [<c07d7008>] (mmc_regulator_set_ocr+0x44/0xd0)
(mmc_regulator_set_ocr) from [<c07e2d80>] (sdhci_set_ios+0xa4/0x490)
(sdhci_set_ios) from [<c07ea690>] (sdhci_omap_set_ios+0x124/0x160)
(sdhci_omap_set_ios) from [<c07c8e94>] (mmc_power_up.part.0+0x3c/0x154)
(mmc_power_up.part.0) from [<c07c9d20>] (mmc_start_host+0x88/0x9c)
(mmc_start_host) from [<c07cad34>] (mmc_add_host+0x58/0x7c)
(mmc_add_host) from [<c07e2574>] (__sdhci_add_host+0xf0/0x22c)
(__sdhci_add_host) from [<c07eaf68>] (sdhci_omap_probe+0x318/0x72c)
(sdhci_omap_probe) from [<c06a39d8>] (platform_probe+0x58/0xb8)
AFAIK we are not seeing this with the devices configured in the mainline
kernel but this can cause issues for folks bringing up their boards.
Fixes: 7d326930d352 ("mmc: sdhci-omap: Add OMAP SDHCI driver")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210921110029.21944-2-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
According to JEDEC Spec, there is no need to do tuning under HS400 mode
since the Rx signal is aligned with the DS signal. However, MediaTek's IC
need set its "DS delay" internally to ensure it can latch Rx signal
correctly.
In previous version, We provide an "hs400-ds-delay" in device tree to cover
different chipset/PCB design, and it works fine in most cases. But, with
the development of process technology and the big VCore voltage scale
range(may have 0.7V/0.6V/0.55V), it is difficult to find a suitable
"hs400-ds-delay" to cover all of IC corner cases(SSSS/TTTT/FFFF). So that
We must have the ability to do hs400 online tuning.
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Reviewed-by: Chaotian Jing <chaotian.jing@mediatek.com>
Link: https://lore.kernel.org/r/20210917124803.22871-4-wenbin.mei@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This adds a ->execute_hs400_tuning() host callback to enable optional
support for host specific tuning for eMMC HS400 mode. Additionally, share
mmc_get_ext_csd() through the public host headerfile, to allow it to be
used by the host drivers, which is needed to support the HS400 tuning.
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Link: https://lore.kernel.org/r/20210917124803.22871-3-wenbin.mei@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The MODULE_DEVICE_TABLE already creates proper alias for platform
driver. Having another MODULE_ALIAS causes the alias to be duplicated.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsunhg.com>
Link: https://lore.kernel.org/r/20210916170511.137915-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The recent change ("dt-bindings: mmc: Convert MMC Card binding to a schema")
renamed: Documentation/devicetree/bindings/mmc/mmc-card.txt
to: Documentation/devicetree/bindings/mmc/mmc-card.yaml.
Let's update its cross-reference accordingly.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/820bb7a1d7e0e51cbea72c9bee6bce806427d1f3.1631785820.git.mchehab+huawei@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Only wait for DRTO on reads, otherwise the driver hangs.
The driver prevents sending CMD12 on response errors like CRCs. According
to the comment this is because some cards have problems with this during
the UHS tuning sequence. Unfortunately this workaround currently also
applies for any command with data. On reads this will set the drto timer,
which then triggers after a while. On writes this will not set any timer
and the tasklet will not be scheduled again.
I cannot test for the UHS workarounds need, but even if so, it should at
most apply to reads. I have observed many hangs when CMD25 response
contained a CRC error. This patch fixes this without touching the actual
UHS tuning workaround.
Signed-off-by: Christian Loehle <cloehle@hyperstone.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/af8f8b8674ba4fcc9a781019e4aeb72c@hyperstone.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
As noted in the "Deprecated Interfaces, Language Features, Attributes,
and Conventions" documentation [1], size calculations (especially
multiplication) should not be performed in memory allocator (or similar)
function arguments due to the risk of them overflowing. This could lead
to values wrapping around and a smaller allocation being made than the
caller was expecting. Using those allocations could lead to linear
overflows of heap memory and other misbehaviors.
So, use the struct_size() helper to do the arithmetic instead of the
argument "size + count * size" in the kzalloc() function.
[1] https://www.kernel.org/doc/html/v5.14/process/deprecated.html#open-coded-arithmetic-in-allocator-arguments
Signed-off-by: Len Baker <len.baker@gmx.com>
Link: https://lore.kernel.org/r/20210911131933.2089-1-len.baker@gmx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Print task count that has not been completed, this is for the
purpose of debugging.
Signed-off-by: Bean Huo <beanhuo@micron.com>
Link: https://lore.kernel.org/r/20210907151204.118861-2-huobean@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Intel Thunder Bay SoC eMMC controller is based on Arasan
eMMC 5.1 host controller IP
Signed-off-by: Rashmi A <rashmi.a@intel.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20210829182443.30802-2-rashmi.a@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Use the helper macro SET_RUNTIME_PM_OPS() instead of the verbose
operators ".runtime_suspend/.runtime_resume", because the
SET_RUNTIME_PM_OPS() is a nice helper macro that could be brought
in to make code a little more concise.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20210907025940.1535-1-caihuoqing@baidu.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
We never checked for errors on add_disk() as this function returned void.
Now that this is fixed, use the shiny new error handling.
Contrary to the typical removal which delays the put_disk() until later,
since we are failing on a probe we immediately put the disk on failure from
add_disk by using blk_cleanup_disk().
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Link: https://lore.kernel.org/r/20210902174105.2418771-4-mcgrof@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
We never checked for errors on add_disk() as this function returned void.
Now that this is fixed, use the shiny new error handling.
Contrary to the typical removal which delays the put_disk() until later,
since we are failing on a probe we immediately put the disk on failure from
add_disk by using blk_cleanup_disk().
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Link: https://lore.kernel.org/r/20210902174105.2418771-3-mcgrof@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
We never checked for errors on add_disk() as this function returned void.
Now that this is fixed, use the shiny new error handling.
The caller only cleanups the disk if we pass on an allocated md but on
error we return return ERR_PTR(ret), and so we must do all the unwinding
ourselves.
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Link: https://lore.kernel.org/r/20210830212538.148729-5-mcgrof@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Remove unused parameters
1. msdc_start_data() - struct mmc_request *mrq
2. msdc_track_cmd_data() - struct mmc_data *data
Signed-off-by: ChanWoo Lee <cw9316.lee@samsung.com>
Link: https://lore.kernel.org/r/20210830021749.5947-1-cw9316.lee@samsung.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The mmc_request structure(*mrq) is not used. //msdc_cmd_find_resp
I remove the unnecessary code related to the mmc_request structure.
Signed-off-by: ChanWoo Lee <cw9316.lee@samsung.com>
Link: https://lore.kernel.org/r/20210827093119.32481-1-cw9316.lee@samsung.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
We found this issue on a 5G platform, during CMDQ error handling, if DMA
status is active when it call msdc_reset_hw(), it means mmc host hw reset
and DMA transfer will be parallel, mmc host may access sram region
unexpectedly. According to the programming guide of mtk-sd host, it needs
to wait for dma stop done after set dma stop.
This change should be applied to all SoCs.
Signed-off-by: Derong Liu <derong.liu@mediatek.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210827071537.1034-1-derong.liu@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
It is replaced with a function that is already declared.
//[1/5] mmc: sdhci: Add helpers for the auto-CMD23 flag
//20200412090349.1607-2-adrian.hunter@intel.com
Signed-off-by: ChanWoo Lee <cw9316.lee@samsung.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20210825093345.14706-1-cw9316.lee@samsung.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
On Thundercomm TurboX CM2290, the eMMC OCR reports vdd = 23 (3.5 ~ 3.6 V),
which is being treated as an invalid value by sdhci_set_power_noreg().
And thus eMMC is totally broken on the platform.
[ 1.436599] ------------[ cut here ]------------
[ 1.436606] mmc0: Invalid vdd 0x17
[ 1.436640] WARNING: CPU: 2 PID: 69 at drivers/mmc/host/sdhci.c:2048 sdhci_set_power_noreg+0x168/0x2b4
[ 1.436655] Modules linked in:
[ 1.436662] CPU: 2 PID: 69 Comm: kworker/u8:1 Tainted: G W 5.15.0-rc1+ #137
[ 1.436669] Hardware name: Thundercomm TurboX CM2290 (DT)
[ 1.436674] Workqueue: events_unbound async_run_entry_fn
[ 1.436685] pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 1.436692] pc : sdhci_set_power_noreg+0x168/0x2b4
[ 1.436698] lr : sdhci_set_power_noreg+0x168/0x2b4
[ 1.436703] sp : ffff800010803a60
[ 1.436705] x29: ffff800010803a60 x28: ffff6a9102465f00 x27: ffff6a9101720a70
[ 1.436715] x26: ffff6a91014de1c0 x25: ffff6a91014de010 x24: ffff6a91016af280
[ 1.436724] x23: ffffaf7b1b276640 x22: 0000000000000000 x21: ffff6a9101720000
[ 1.436733] x20: ffff6a9101720370 x19: ffff6a9101720580 x18: 0000000000000020
[ 1.436743] x17: 0000000000000000 x16: 0000000000000004 x15: ffffffffffffffff
[ 1.436751] x14: 0000000000000000 x13: 00000000fffffffd x12: ffffaf7b1b84b0bc
[ 1.436760] x11: ffffaf7b1b720d10 x10: 000000000000000a x9 : ffff800010803a60
[ 1.436769] x8 : 000000000000000a x7 : 000000000000000f x6 : 00000000fffff159
[ 1.436778] x5 : 0000000000000000 x4 : 0000000000000000 x3 : 00000000ffffffff
[ 1.436787] x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff6a9101718d80
[ 1.436797] Call trace:
[ 1.436800] sdhci_set_power_noreg+0x168/0x2b4
[ 1.436805] sdhci_set_ios+0xa0/0x7fc
[ 1.436811] mmc_power_up.part.0+0xc4/0x164
[ 1.436818] mmc_start_host+0xa0/0xb0
[ 1.436824] mmc_add_host+0x60/0x90
[ 1.436830] __sdhci_add_host+0x174/0x330
[ 1.436836] sdhci_msm_probe+0x7c0/0x920
[ 1.436842] platform_probe+0x68/0xe0
[ 1.436850] really_probe.part.0+0x9c/0x31c
[ 1.436857] __driver_probe_device+0x98/0x144
[ 1.436863] driver_probe_device+0xc8/0x15c
[ 1.436869] __device_attach_driver+0xb4/0x120
[ 1.436875] bus_for_each_drv+0x78/0xd0
[ 1.436881] __device_attach_async_helper+0xac/0xd0
[ 1.436888] async_run_entry_fn+0x34/0x110
[ 1.436895] process_one_work+0x1d0/0x354
[ 1.436903] worker_thread+0x13c/0x470
[ 1.436910] kthread+0x150/0x160
[ 1.436915] ret_from_fork+0x10/0x20
[ 1.436923] ---[ end trace fcfac44cb045c3a8 ]---
Fix the issue by mapping MMC_VDD_35_36 (and MMC_VDD_34_35) to
SDHCI_POWER_330 as well.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211004024935.15326-1-shawn.guo@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Return an error code if usb_get_function() fails. Don't return success.
Fixes: 4bc8a33f2407 ("usb: gadget: hid: convert to new interface of f_hid")
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20211011123739.GC15188@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The device may take up to 100ms to become responsive during probe, so
prefer asynchronous probing to avoid delaying the rest of the system.
Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: John Keeping <john@metanate.com>
Link: https://lore.kernel.org/r/20211007111217.1935858-1-john@metanate.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
I have a ST1633 touch controller which fails to probe due to a timeout
waiting for the controller to become ready. Increasing the minimum
delay to 100ms ensures that the probe sequence completes successfully.
The ST1633 datasheet says nothing about the maximum delay here and the
ST1232 I2C protocol document says "wait until" with no notion of a
timeout.
Since this only runs once during probe, being generous with the timout
seems reasonable and most likely the device will become ready
eventually.
(It may be worth noting that I saw this issue with a PREEMPT_RT patched
kernel which probably has tighter wakeups from usleep_range() than other
preemption models.)
Fixes: f605be6a57b4 ("Input: st1232 - wait until device is ready before reading resolution")
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210929152609.2421483-1-john@metanate.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Add support for PCIe SATA expander cards based on ASMedia 1062 + JBM575
controllers.
These cards can provide up to 10 or more SATA ports on one PCIe card.
Signed-off-by: István Pongrácz <pongracz.istvan@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
|
|
The last byte of "pad" is used without being initialized.
Fixes: 55dba3120fbc ("libata: update ->data_xfer hook for ATAPI")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
|
|
* Fix a new crash on dev file close if the dev file was opened when
GPU is not loaded (such as missing fw in initrd)
* Switch to single drm_sched_entity per priority level per drm_file
to unbreak multi-context userspace
* Serialize GMU access to fix GMU OOB errors
* Various error path fixes
* A couple integer overflow fixes
* Fix mdp5 cursor plane WARNs
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGtD4u7yyiy+BQLmibUCbn=AdDRu7FrmdViHVx0QrcGf8g@mail.gmail.com
|
|
This disables a lock which wasn't enabled and it does not disable
the first lock in the array.
Fixes: 6e0eb52eba9e ("drm/msm/dsi: Parse bus clocks from a list")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20211001123409.GG2283@kili
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
Return an error code if msm_dsi_manager_validate_current_config().
Don't return success.
Fixes: 8b03ad30e314 ("drm/msm/dsi: Use one connector for dual DSI mode")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20211001123308.GF2283@kili
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
The downstream driver models this PLL lock check as an if-elseif-else.
The only way to reach the else case where pll_locked=true [1] is by
succeeding both readl_poll_timeout_atomic calls (which return zero on
success) in the if _and_ elseif condition. Hence both the "lock" and
"ready" bit need to be tested in the SM_READY_STATUS register before
considering the PLL locked and ready to go.
Tested on the Sony Xperia XA2 Ultra (nile-discovery, sdm630).
[1]: https://source.codeaurora.org/quic/la/kernel/msm-4.19/tree/drivers/clk/qcom/mdss/mdss-dsi-pll-14nm-util.c?h=LA.UM.9.2.1.r1-08000-sdm660.0#n302
Fixes: f079f6d999cb ("drm/msm/dsi: Add PHY/PLL for 8x96")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210906202552.824598-1-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
The commit 9f91f22aafcd ("drm/msm/dsi: remove duplicate fields from
dsi_pll_Nnm instances") mistakenly changed registered clock names. While
the platform is in progress of migration to using clock properties in
the dts rather than the global clock names, we should provide backwards
compatibility. Thus restore registerd global clock names.
Fixes: 9f91f22aafcd ("drm/msm/dsi: remove duplicate fields from dsi_pll_Nnm instances")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Link: https://lore.kernel.org/r/20210921162245.1858118-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
Both PINGPONG4 and PINGPONG5 IRQ registers are using the
same address, which is incorrect. PINGPONG4 should use the
register offset 30, and PINGPONG5 should use the register
offset 31 according to the downstream driver.
Fixes: 667e9985ee24 ("drm/msm/dpu: replace IRQ lookup with the data in hw catalog")
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210819133636.2045766-1-robert.foss@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
Since commit 98659487b845 ("drm/msm: add support to take dpu snapshot")
the following NULL pointer dereference is seen on i.MX53:
[ 3.275493] msm msm: bound 30000000.gpu (ops a3xx_ops)
[ 3.287174] [drm] Initialized msm 1.8.0 20130625 for msm on minor 0
[ 3.293915] 8<--- cut here ---
[ 3.297012] Unable to handle kernel NULL pointer dereference at virtual address 00000028
[ 3.305244] pgd = (ptrval)
[ 3.307989] [00000028] *pgd=00000000
[ 3.311624] Internal error: Oops: 805 [#1] SMP ARM
[ 3.316430] Modules linked in:
[ 3.319503] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.14.0+g682d702b426b #1
[ 3.326652] Hardware name: Freescale i.MX53 (Device Tree Support)
[ 3.332754] PC is at __mutex_init+0x14/0x54
[ 3.336969] LR is at msm_disp_snapshot_init+0x24/0xa0
i.MX53 does not use the DPU controller.
Fix the problem by only calling msm_disp_snapshot_init() on platforms that
use the DPU controller.
Cc: stable@vger.kernel.org
Fixes: 98659487b845 ("drm/msm: add support to take dpu snapshot")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210914174831.2044420-1-festevam@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
These error paths returned 1 on failure, instead of a negative error
code. This would lead to an Oops in the caller. A second problem is
that the check for "if (ret != -ENODATA)" did not work because "ret" was
set to 1.
Fixes: 5785dd7a8ef0 ("drm/msm: Fix duplicate gpu node in icc summary")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20211001125904.GK2283@kili
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
This code returns 1 on error instead of a negative error. It leads to
an Oops in the caller. A second problem is that the check for
"if (ret != -ENODATA)" cannot be true because "ret" is set to 1.
Fixes: 5785dd7a8ef0 ("drm/msm: Fix duplicate gpu node in icc summary")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20211001125759.GJ2283@kili
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
The initialization of pointer dev dereferences pointer edp before
edp is null checked, so there is a potential null pointer deference
issue. Fix this by only dereferencing edp after edp has been null
checked.
Addresses-Coverity: ("Dereference before null check")
Fixes: ab5b0107ccf3 ("drm/msm: Initial add eDP support in msm drm driver (v5)")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210929121857.213922-1-colin.king@canonical.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
Since f35a2a99100f ("drm/encoder: make encoder control functions
optional") drm_mode_config_validate would print warnings if both cursor
plane and cursor functions are provided. Restore separate set of
drm_crtc_funcs to be used if separate cursor plane is provided.
[ 6.556046] ------------[ cut here ]------------
[ 6.556071] [CRTC:93:crtc-0] must not have both a cursor plane and a cursor_set func
[ 6.556091] WARNING: CPU: 1 PID: 76 at drivers/gpu/drm/drm_mode_config.c:648 drm_mode_config_validate+0x238/0x4d0
[ 6.567453] Modules linked in:
[ 6.577604] CPU: 1 PID: 76 Comm: kworker/u8:2 Not tainted 5.15.0-rc1-dirty #43
[ 6.580557] Hardware name: Qualcomm Technologies, Inc. DB820c (DT)
[ 6.587763] Workqueue: events_unbound deferred_probe_work_func
[ 6.593926] pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 6.599740] pc : drm_mode_config_validate+0x238/0x4d0
[ 6.606596] lr : drm_mode_config_validate+0x238/0x4d0
[ 6.611804] sp : ffff8000121b3980
[ 6.616838] x29: ffff8000121b3990 x28: 0000000000000000 x27: 0000000000000001
[ 6.620140] x26: ffff8000114cde50 x25: ffff8000114cdd40 x24: ffff0000987282d8
[ 6.627258] x23: 0000000000000000 x22: 0000000000000000 x21: 0000000000000001
[ 6.634376] x20: ffff000098728000 x19: ffff000080a39000 x18: ffffffffffffffff
[ 6.641494] x17: 3136564e3631564e x16: 0000000000000324 x15: ffff800011c78709
[ 6.648613] x14: 0000000000000000 x13: ffff800011a22850 x12: 00000000000009ab
[ 6.655730] x11: 0000000000000339 x10: ffff800011a22850 x9 : ffff800011a22850
[ 6.662848] x8 : 00000000ffffefff x7 : ffff800011a7a850 x6 : ffff800011a7a850
[ 6.669966] x5 : 000000000000bff4 x4 : 40000000fffff339 x3 : 0000000000000000
[ 6.677084] x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff00008093b800
[ 6.684205] Call trace:
[ 6.691319] drm_mode_config_validate+0x238/0x4d0
[ 6.693577] drm_dev_register+0x17c/0x210
[ 6.698435] msm_drm_bind+0x4b4/0x694
[ 6.702429] try_to_bring_up_master+0x164/0x1d0
[ 6.706075] __component_add+0xa0/0x170
[ 6.710415] component_add+0x14/0x20
[ 6.714234] msm_hdmi_dev_probe+0x1c/0x2c
[ 6.718053] platform_probe+0x68/0xe0
[ 6.721959] really_probe.part.0+0x9c/0x30c
[ 6.725606] __driver_probe_device+0x98/0x144
[ 6.729600] driver_probe_device+0xc8/0x15c
[ 6.734114] __device_attach_driver+0xb4/0x120
[ 6.738106] bus_for_each_drv+0x78/0xd0
[ 6.742619] __device_attach+0xdc/0x184
[ 6.746351] device_initial_probe+0x14/0x20
[ 6.750172] bus_probe_device+0x9c/0xa4
[ 6.754337] deferred_probe_work_func+0x88/0xc0
[ 6.758158] process_one_work+0x1d0/0x370
[ 6.762671] worker_thread+0x2c8/0x470
[ 6.766839] kthread+0x15c/0x170
[ 6.770483] ret_from_fork+0x10/0x20
[ 6.773870] ---[ end trace 5884eb76cd26d274 ]---
[ 6.777500] ------------[ cut here ]------------
[ 6.782043] [CRTC:93:crtc-0] must not have both a cursor plane and a cursor_move func
[ 6.782063] WARNING: CPU: 1 PID: 76 at drivers/gpu/drm/drm_mode_config.c:654 drm_mode_config_validate+0x290/0x4d0
[ 6.794362] Modules linked in:
[ 6.804600] CPU: 1 PID: 76 Comm: kworker/u8:2 Tainted: G W 5.15.0-rc1-dirty #43
[ 6.807555] Hardware name: Qualcomm Technologies, Inc. DB820c (DT)
[ 6.816148] Workqueue: events_unbound deferred_probe_work_func
[ 6.822311] pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 6.828126] pc : drm_mode_config_validate+0x290/0x4d0
[ 6.834981] lr : drm_mode_config_validate+0x290/0x4d0
[ 6.840189] sp : ffff8000121b3980
[ 6.845223] x29: ffff8000121b3990 x28: 0000000000000000 x27: 0000000000000001
[ 6.848525] x26: ffff8000114cde50 x25: ffff8000114cdd40 x24: ffff0000987282d8
[ 6.855643] x23: 0000000000000000 x22: 0000000000000000 x21: 0000000000000001
[ 6.862763] x20: ffff000098728000 x19: ffff000080a39000 x18: ffffffffffffffff
[ 6.869879] x17: 3136564e3631564e x16: 0000000000000324 x15: ffff800011c790c2
[ 6.876998] x14: 0000000000000000 x13: ffff800011a22850 x12: 0000000000000a2f
[ 6.884116] x11: 0000000000000365 x10: ffff800011a22850 x9 : ffff800011a22850
[ 6.891234] x8 : 00000000ffffefff x7 : ffff800011a7a850 x6 : ffff800011a7a850
[ 6.898351] x5 : 000000000000bff4 x4 : 40000000fffff365 x3 : 0000000000000000
[ 6.905470] x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff00008093b800
[ 6.912590] Call trace:
[ 6.919702] drm_mode_config_validate+0x290/0x4d0
[ 6.921960] drm_dev_register+0x17c/0x210
[ 6.926821] msm_drm_bind+0x4b4/0x694
[ 6.930813] try_to_bring_up_master+0x164/0x1d0
[ 6.934459] __component_add+0xa0/0x170
[ 6.938799] component_add+0x14/0x20
[ 6.942619] msm_hdmi_dev_probe+0x1c/0x2c
[ 6.946438] platform_probe+0x68/0xe0
[ 6.950345] really_probe.part.0+0x9c/0x30c
[ 6.953991] __driver_probe_device+0x98/0x144
[ 6.957984] driver_probe_device+0xc8/0x15c
[ 6.962498] __device_attach_driver+0xb4/0x120
[ 6.966492] bus_for_each_drv+0x78/0xd0
[ 6.971004] __device_attach+0xdc/0x184
[ 6.974737] device_initial_probe+0x14/0x20
[ 6.978556] bus_probe_device+0x9c/0xa4
[ 6.982722] deferred_probe_work_func+0x88/0xc0
[ 6.986543] process_one_work+0x1d0/0x370
[ 6.991057] worker_thread+0x2c8/0x470
[ 6.995223] kthread+0x15c/0x170
[ 6.998869] ret_from_fork+0x10/0x20
[ 7.002255] ---[ end trace 5884eb76cd26d275 ]---
Fixes: aa649e875daf ("drm/msm/mdp5: mdp5_crtc: Restore cursor state only if LM cursors are enabled")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210925192824.3416259-1-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
The return type of ktime_divns() is s64. The timeout_to_jiffies() currently
assigns the result of this ktime_divns() to unsigned long, which on 32 bit
systems may overflow. Furthermore, the result of this function is sometimes
also passed to functions which expect signed long, dma_fence_wait_timeout()
is one such example.
Fix this by adjusting the type of remaining_jiffies to s64, so we do not
suffer overflow there, and return a value limited to range of 0..INT_MAX,
which is safe for all usecases of this timeout.
The above overflow can be triggered if userspace passes in too large timeout
value, larger than INT_MAX / HZ seconds. The kernel detects it and complains
about "schedule_timeout: wrong timeout value %lx" and generates a warning
backtrace.
Note that this fixes commit 6cedb8b377bb ("drm/msm: avoid using 'timespec'"),
because the previously used timespec_to_jiffies() function returned unsigned
long instead of s64:
static inline unsigned long timespec_to_jiffies(const struct timespec *value)
Fixes: 6cedb8b377bb ("drm/msm: avoid using 'timespec'")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jordan Crouse <jcrouse@codeaurora.org>
Cc: Rob Clark <robdclark@chromium.org>
Cc: stable@vger.kernel.org # 5.6+
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210917005913.157379-1-marex@denx.de
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
There is no devfreq on a3xx at the moment since gpu_busy is not
implemented. This means that msm_devfreq_init() will return early
and the entire devfreq setup is skipped.
However, msm_devfreq_active() and msm_devfreq_idle() are still called
unconditionally later, causing a NULL pointer dereference:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000010
Internal error: Oops: 96000004 [#1] PREEMPT SMP
CPU: 0 PID: 133 Comm: ring0 Not tainted 5.15.0-rc1 #4
Hardware name: Longcheer L8150 (DT)
pc : mutex_lock_io+0x2bc/0x2f0
lr : msm_devfreq_active+0x3c/0xe0 [msm]
Call trace:
mutex_lock_io+0x2bc/0x2f0
msm_gpu_submit+0x164/0x180 [msm]
msm_job_run+0x54/0xe0 [msm]
drm_sched_main+0x2b0/0x4a0 [gpu_sched]
kthread+0x154/0x160
ret_from_fork+0x10/0x20
Fix this by adding a check in msm_devfreq_active/idle() which ensures
that devfreq was actually initialized earlier.
Fixes: 9bc95570175a ("drm/msm: Devfreq tuning")
Reported-by: Nikita Travkin <nikita@trvn.ru>
Tested-by: Nikita Travkin <nikita@trvn.ru>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210913164556.16284-1-stephan@gerhold.net
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
Currently there is audio not working problem after system resume from suspend
if hdmi monitor stay plugged in at DUT. However this problem does not happen
at normal operation but at a particular test case. The root cause is DP driver
signal audio with connected state at resume which trigger audio trying to setup
audio data path through DP main link but failed due to display port is not setup
and enabled by upper layer framework yet. This patch only have DP driver signal
audio only when DP is in disconnected state so that audio option shows correct
state after system resume. DP driver will not signal audio with connected state
until display enabled executed by upper layer framework where display port is
setup completed and main link is running.
Changes in V2:
-- add details commit text
Fixes: afc9b8b6bab8 ("drm/msm/dp: signal audio plugged change at dp_pm_resume")
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1632932224-25102-1-git-send-email-khsieh@codeaurora.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
Pull Kunit fixes from Shuah Khan:
- Fixes to address the structleak plugin causing the stack frame size
to grow immensely when used with KUnit. Fixes include adding a new
makefile to disable structleak and using it from KUnit iio, device
property, thunderbolt, and bitfield tests to disable it.
- KUnit framework reference count leak in kfree_at_end
- KUnit tool fix to resolve conflict between --json and --raw_output
and generate correct test output in either case.
- kernel-doc warnings due to mismatched arg names
* tag 'linux-kselftest-kunit-fixes-5.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
kunit: fix kernel-doc warnings due to mismatched arg names
bitfield: build kunit tests without structleak plugin
thunderbolt: build kunit tests without structleak plugin
device property: build kunit tests without structleak plugin
iio/test-format: build kunit tests without structleak plugin
gcc-plugins/structleak: add makefile var for disabling structleak
kunit: fix reference count leak in kfree_at_end
kunit: tool: better handling of quasi-bool args (--json, --raw_output)
|
|
This reverts commit c1ec54b7b5af25c779192253f5a9f05e95cb43d7.
Commit c1ec54b7b5af
("drm/mediatek: Use mailbox rx_callback instead of cmdq_task_cb")
would cause numerous mtk cmdq mailbox driver warning:
WARNING: CPU: 0 PID: 0 at drivers/mailbox/mtk-cmdq-mailbox.c:198
cmdq_task_exec_done+0xb8/0xe0
So revert that patch.
Reported-by: Enric Balletbo Serra <eballetbo@gmail.com>
Tested-by: Enric Balletbo Serra <eballetbo@gmail.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
|
|
This reverts commit f4be17cd5b14dd73545b0e014a63ebe9ab5ef837.
Commit c1ec54b7b5af
("drm/mediatek: Use mailbox rx_callback instead of cmdq_task_cb")
would cause numerous mtk cmdq mailbox driver warning:
WARNING: CPU: 0 PID: 0 at drivers/mailbox/mtk-cmdq-mailbox.c:198
cmdq_task_exec_done+0xb8/0xe0
So revert that patch and all the patches depend on that patch.
Reported-by: Enric Balletbo Serra <eballetbo@gmail.com>
Tested-by: Enric Balletbo Serra <eballetbo@gmail.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
|
|
This reverts commit 8cdcb365342402fdeb664479b0a04e9debef8efb.
Commit c1ec54b7b5af
("drm/mediatek: Use mailbox rx_callback instead of cmdq_task_cb")
would cause numerous mtk cmdq mailbox driver warning:
WARNING: CPU: 0 PID: 0 at drivers/mailbox/mtk-cmdq-mailbox.c:198
cmdq_task_exec_done+0xb8/0xe0
So revert that patch and all the patches depend on that patch.
Reported-by: Enric Balletbo Serra <eballetbo@gmail.com>
Tested-by: Enric Balletbo Serra <eballetbo@gmail.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
|
|
This reverts commit bc9241be73d9b2b3bcb7033598521fd669639848.
Commit c1ec54b7b5af
("drm/mediatek: Use mailbox rx_callback instead of cmdq_task_cb")
would cause numerous mtk cmdq mailbox driver warning:
WARNING: CPU: 0 PID: 0 at drivers/mailbox/mtk-cmdq-mailbox.c:198
cmdq_task_exec_done+0xb8/0xe0
So revert that patch and all the patches depend on that patch.
Reported-by: Enric Balletbo Serra <eballetbo@gmail.com>
Tested-by: Enric Balletbo Serra <eballetbo@gmail.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
|
|
ftrace is a preferred and standard way to debug entering and exiting
functions so drop useless debug prints.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ftrace is a preferred and standard way to debug entering and exiting
functions so drop useless debug prints.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ftrace is a preferred and standard way to debug entering and exiting
functions so drop useless debug prints.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
Linus Walleij
Tony Lindgren
Wenbin Mei
Krzysztof Kozlowski
Mauro Carvalho Chehab
Christian Löhle
Len Baker
Bean Huo
Rashmi A
Cai Huoqing
Luis Chamberlain
ChanWoo Lee
Derong Liu
Shawn Guo
Dan Carpenter
John Keeping
István Pongrácz
Dave Airlie
Marijn Suijten
Dmitry Baryshkov
Robert Foss
Fabio Estevam
Colin Ian King
Marek Vasut
Stephan Gerhold
Kuogee Hsieh
Linus Torvalds
Chun-Kuang Hu