| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
From original QCA source code the port was set to prefer master as port
type in 1000BASE-T mode. Apply the same settings also here.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
QCA8327 internal phy require DAC amplitude adjustement set to +6% with
100m speed. Also add additional define to report a change of the same
reg in QCA8337. (different scope it does set 1000m voltage)
Add link_change_notify function to set the proper amplitude adjustement
on PHY_RUNNING state and disable on any other state.
Fixes: b4df02b562f4 ("net: phy: at803x: add support for qca 8327 A variant internal phy")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
From Documentation phy resume triggers phy reset and restart
auto-negotiation. Add a dedicated function to wait reset to finish as
it was notice a regression where port sometime are not reliable after a
suspend/resume session. The reset wait logic is copied from phy_poll_reset.
Add dedicated suspend function to use genphy_suspend only with QCA8337
phy and set only additional debug settings for QCA8327. With more test
it was reported that QCA8327 doesn't proprely support this mode and
using this cause the unreliability of the switch ports, especially the
malfunction of the port0.
Fixes: 15b9df4ece17 ("net: phy: at803x: add resume/suspend function to qca83xx phy")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use netif_is_bond_master() function instead of open code, which is
((event_dev->priv_flags & IFF_BONDING) && (event_dev->flags & IFF_MASTER)).
This patch doesn't change logic.
Signed-off-by: Juhee Kang <claudiajkang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The open code which is dev->priv_flags & IFF_RXFH_CONFIGURED is defined as
a helper function on netdevice.h. So use netif_is_rxfh_configured()
function instead of open code. This patch doesn't change logic.
Signed-off-by: Juhee Kang <claudiajkang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Override the automatic AdminQ error message in order to
capture the potential No Space message when we hit the
max vlan limit, and add additional messaging to detail
what filter failed.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The AdminQ handler has an error handler that automatically prints
an error message when the request has failed. However, there are
situations where the caller can expect that it might fail and has
an alternative strategy, thus may not want the error message sent
to the log, such as hitting -ENOSPC when adding a new vlan id.
We add a new interface to the AdminQ API to allow for override of
the default behavior, and an interface to the use standard error
message formatting.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add vlans to the existing rx_filter_sync mechanics currently
used for managing mac filters.
Older versions of our firmware had no enforced limits on the
number of vlans that the LIF could request, but requesting large
numbers of vlans caused issues in FW memory management, so an
arbitrary limit was added in the FW. The FW now returns -ENOSPC
when it hits that limit, which the driver needs to handle.
Unfortunately, the FW doesn't advertise the vlan id limit,
as it does with mac filters, so the driver won't know the
limit until it bumps into it. We'll grab the current vlan id
count and use that as the limit from there on and thus prevent
getting any more -ENOSPC errors.
Just as is done for the mac filters, the device puts the device
into promiscuous mode when -ENOSPC is seen for vlan ids, and
the driver will track the vlans that aren't synced to the FW.
When vlans are removed, the driver will retry the un-synced
vlans. If all outstanding vlans are synced, the promiscuous
mode will be disabled.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similar to the filter add, make a generic filter delete.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for adding vlan overflow management, rework
the ionic_lif_addr_add() function to something a little more
generic that can be used for other filter types.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for enhancing vlan filter management,
add a filter search routine that can figure out for
itself which type of filter search is needed.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The overflow flags really aren't useful and we don't need lif
struct elements to track them.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The routines that add and delete mac addresses from the
firmware really should be in the file with the rest of
the filter management. This simply moves the functions
with no logic changes.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Dump the filter list to debugfs - includes the device-assigned
filter id and the sync'd-to-hardware status.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
savagefb and some other drivers call kfree to free 'info->pixmap.addr'
even after calling unregister_framebuffer, which may cause double free.
Fix this by setting 'fb_info->pixmap.addr' to NULL after kfree in
unregister_framebuffer.
The following log reveals it:
[ 37.318872] BUG: KASAN: double-free or invalid-free in kfree+0x13e/0x290
[ 37.319369]
[ 37.320803] Call Trace:
[ 37.320992] dump_stack_lvl+0xa8/0xd1
[ 37.321274] print_address_description+0x87/0x3b0
[ 37.321632] ? kfree+0x13e/0x290
[ 37.321879] ? kfree+0x13e/0x290
[ 37.322126] ? kfree+0x13e/0x290
[ 37.322374] kasan_report_invalid_free+0x58/0x90
[ 37.322724] ____kasan_slab_free+0x123/0x140
[ 37.323049] __kasan_slab_free+0x11/0x20
[ 37.323347] slab_free_freelist_hook+0x81/0x150
[ 37.323689] ? savagefb_remove+0xa1/0xc0 [savagefb]
[ 37.324066] kfree+0x13e/0x290
[ 37.324304] savagefb_remove+0xa1/0xc0 [savagefb]
[ 37.324655] pci_device_remove+0xa9/0x250
[ 37.324959] ? pci_device_probe+0x7d0/0x7d0
[ 37.325273] device_release_driver_internal+0x4f7/0x7a0
[ 37.325666] driver_detach+0x1e8/0x2c0
[ 37.325952] bus_remove_driver+0x134/0x290
[ 37.326262] ? sysfs_remove_groups+0x97/0xb0
[ 37.326584] driver_unregister+0x77/0xa0
[ 37.326883] pci_unregister_driver+0x2c/0x1c0
[ 37.336124]
[ 37.336245] Allocated by task 5465:
[ 37.336507] ____kasan_kmalloc+0xb5/0xe0
[ 37.336801] __kasan_kmalloc+0x9/0x10
[ 37.337069] kmem_cache_alloc_trace+0x12b/0x220
[ 37.337405] register_framebuffer+0x3f3/0xa00
[ 37.337731] foo_register_framebuffer+0x3b/0x50 [savagefb]
[ 37.338136]
[ 37.338255] Freed by task 5475:
[ 37.338492] kasan_set_track+0x3d/0x70
[ 37.338774] kasan_set_free_info+0x23/0x40
[ 37.339081] ____kasan_slab_free+0x10b/0x140
[ 37.339399] __kasan_slab_free+0x11/0x20
[ 37.339694] slab_free_freelist_hook+0x81/0x150
[ 37.340034] kfree+0x13e/0x290
[ 37.340267] do_unregister_framebuffer+0x21c/0x3d0
[ 37.340624] unregister_framebuffer+0x23/0x40
[ 37.340950] savagefb_remove+0x45/0xc0 [savagefb]
[ 37.341302] pci_device_remove+0xa9/0x250
[ 37.341603] device_release_driver_internal+0x4f7/0x7a0
[ 37.341990] driver_detach+0x1e8/0x2c0
[ 37.342272] bus_remove_driver+0x134/0x290
[ 37.342577] driver_unregister+0x77/0xa0
[ 37.342873] pci_unregister_driver+0x2c/0x1c0
[ 37.343196] cleanup_module+0x15/0x1c [savagefb]
[ 37.343543] __se_sys_delete_module+0x398/0x490
[ 37.343881] __x64_sys_delete_module+0x56/0x60
[ 37.344221] do_syscall_64+0x4d/0xc0
[ 37.344492] entry_SYSCALL_64_after_hwframe+0x44/0xae
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1633848148-29747-1-git-send-email-zheyuma97@gmail.com
|
|
Pull i2c fixes from Wolfram Sang:
"Three driver bugfixes and one leak fix for the core"
* 'i2c/for-current-fixed' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: mlxcpld: Modify register setting for 400KHz frequency
i2c: mlxcpld: Fix criteria for frequency setting
i2c: mediatek: Add OFFSET_EXT_CONF setting back
i2c: acpi: fix resource leak in reconfiguration device addition
|
|
Pull SCSI fixes from James Bottomley:
"Five fixes, all in drivers.
The big change is the UFS task management rework, with lpfc next and
the rest being fairly minor and obvious fixes"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: iscsi: Fix iscsi_task use after free
scsi: lpfc: Fix memory overwrite during FC-GS I/O abort handling
scsi: elx: efct: Delete stray unlock statement
scsi: ufs: core: Fix task management completion
scsi: acornscsi: Remove scsi_cmd_to_tag() reference
|
|
pll0831x PLL is used in Exynos850 SoC for top-level fractional PLLs. The
code was derived from very similar pll36xx type, with next differences:
1. Lock time for pll0831x is 500*P_DIV, when for pll36xx it's 3000*P_DIV
2. It's not suggested in Exynos850 TRM that S_DIV change doesn't require
performing PLL lock procedure (which is done in pll36xx
implementation)
3. The offset from PMS-values register to K-value register is 0x8 for
pll0831x, when for pll36xx it's 0x4
When defining pll0831x type, CON3 register offset should be provided as
a "con" parameter of PLL() macro, like this:
PLL(pll_0831x, 0, "fout_mmc_pll", "oscclk",
PLL_LOCKTIME_PLL_MMC, PLL_CON3_PLL_MMC, pll0831x_26mhz_tbl),
To define PLL rates table, one can use PLL_36XX_RATE() macro, e.g.:
PLL_36XX_RATE(26 * MHZ, 799999877, 31, 1, 0, -15124)
as it's completely appropriate for pl0831x type and there is no sense in
duplicating that.
If bit #1 (MANUAL_PLL_CTRL) is not set in CON1 register, it won't be
possible to set new rate, with next error showing in kernel log:
Could not lock PLL fout_mmc_pll
That can happen for example if bootloader clears that bit beforehand.
PLL driver doesn't account for that, so if MANUAL_PLL_CTRL bit was
cleared, it's assumed it was done for a reason and it shouldn't be
possible to change that PLL's rate at all.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Link: https://lore.kernel.org/r/20211008154352.19519-3-semen.protsenko@linaro.org
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
pll0822x PLL is used in Exynos850 SoC for top-level integer PLLs. The
code was derived from very similar pll35xx type, with next differences:
1. Lock time for pll0822x is 150*P_DIV, when for pll35xx it's 270*P_DIV
2. It's not suggested in Exynos850 TRM that S_DIV change doesn't require
performing PLL lock procedure (which is done in pll35xx
implementation)
When defining pll0822x type, CON3 register offset should be provided as
a "con" parameter of PLL() macro, like this:
PLL(pll_0822x, 0, "fout_shared0_pll", "oscclk",
PLL_LOCKTIME_PLL_SHARED0, PLL_CON3_PLL_SHARED0,
exynos850_shared0_pll_rates),
To define PLL rates table, one can use PLL_35XX_RATE() macro, e.g.:
PLL_35XX_RATE(26 * MHZ, 1600 * MHZ, 800, 13, 0)
as it's completely appropriate for pl0822x type and there is no sense in
duplicating that.
If bit #1 (MANUAL_PLL_CTRL) is not set in CON1 register, it won't be
possible to set new rate, with next error showing in kernel log:
Could not lock PLL fout_shared1_pll
That can happen for example if bootloader clears that bit beforehand.
PLL driver doesn't account for that, so if MANUAL_PLL_CTRL bit was
cleared, it's assumed it was done for a reason and it shouldn't be
possible to change that PLL's rate at all.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Link: https://lore.kernel.org/r/20211008154352.19519-2-semen.protsenko@linaro.org
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
This reverts commit
223cce88a926 ("drm/panel: Add support for Sharp LS060T1SX01 panel").
It was pushed to drm-misc-next by accident.
Added my own ack to expedit the revert.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210926001005.3442668-3-dmitry.baryshkov@linaro.org
|
|
Add driver to support Sharp LS06T1SX01 FullHD panel. The panel uses
nt35695 driver IC. For example this LCD module can be found in the
kwaek.ca Dragonboard Display Adapter Bundle.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210926001005.3442668-3-dmitry.baryshkov@linaro.org
|
|
Add support for the Logic Technologies LTTD800x480 L2RT 7" 800x480 TFT
Resistive Touch Module.
Signed-off-by: Søren Andersen <san@skov.dk>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210930100501.15690-3-o.rempel@pengutronix.de
|
|
commit 126285651b7f ("Merge ra.kernel.org:/pub/scm/linux/kernel/git/netdev/net")
accidentally reverted the effect of
commit 1a8024239da ("virtio-net: fix for skb_over_panic inside big mode")
on drivers/net/virtio_net.c
As a result, users of crosvm (which is using large packet mode)
are experiencing crashes with 5.14-rc1 and above that do not
occur with 5.13.
Crash trace:
[ 61.346677] skbuff: skb_over_panic: text:ffffffff881ae2c7 len:3762 put:3762 head:ffff8a5ec8c22000 data:ffff8a5ec8c22010 tail:0xec2 end:0xec0 dev:<NULL>
[ 61.369192] kernel BUG at net/core/skbuff.c:111!
[ 61.372840] invalid opcode: 0000 [#1] SMP PTI
[ 61.374892] CPU: 5 PID: 0 Comm: swapper/5 Not tainted 5.14.0-rc1 linux-v5.14-rc1-for-mesa-ci.tar.bz2 #1
[ 61.376450] Hardware name: ChromiumOS crosvm, BIOS 0
..
[ 61.393635] Call Trace:
[ 61.394127] <IRQ>
[ 61.394488] skb_put.cold+0x10/0x10
[ 61.395095] page_to_skb+0xf7/0x410
[ 61.395689] receive_buf+0x81/0x1660
[ 61.396228] ? netif_receive_skb_list_internal+0x1ad/0x2b0
[ 61.397180] ? napi_gro_flush+0x97/0xe0
[ 61.397896] ? detach_buf_split+0x67/0x120
[ 61.398573] virtnet_poll+0x2cf/0x420
[ 61.399197] __napi_poll+0x25/0x150
[ 61.399764] net_rx_action+0x22f/0x280
[ 61.400394] __do_softirq+0xba/0x257
[ 61.401012] irq_exit_rcu+0x8e/0xb0
[ 61.401618] common_interrupt+0x7b/0xa0
[ 61.402270] </IRQ>
See
https://lore.kernel.org/r/5edaa2b7c2fe4abd0347b8454b2ac032b6694e2c.camel%40collabora.com
for the report.
Apply the original 1a8024239da ("virtio-net: fix for skb_over_panic inside big mode")
again, the original logic still holds:
In virtio-net's large packet mode, there is a hole in the space behind
buf.
hdr_padded_len - hdr_len
We must take this into account when calculating tailroom.
Cc: Greg KH <gregkh@linuxfoundation.org>
Fixes: fb32856b16ad ("virtio-net: page_to_skb() use build_skb when there's sufficient tailroom")
Fixes: 126285651b7f ("Merge ra.kernel.org:/pub/scm/linux/kernel/git/netdev/net")
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Reported-by: Corentin Noël <corentin.noel@collabora.com>
Tested-by: Corentin Noël <corentin.noel@collabora.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case a PHY device was probed thus in the PHY_READY state, but not
configured and with no network device attached yet, we should not be
trying to shut it down because it has been brought back into reset by
phy_device_reset() towards the end of phy_probe() and anyway we have not
configured the PHY yet.
Fixes: e2f016cf7751 ("net: phy: add a shutdown procedure")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The error code is missing in this code scenario, add the error code
'-EINVAL' to the return value 'rc'.
Eliminate the follow smatch warning:
drivers/net/ethernet/qlogic/qed/qed_main.c:1298 qed_slowpath_start()
warn: missing error code 'rc'.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Fixes: d51e4af5c209 ("qed: aRFS infrastructure support")
Signed-off-by: chongjiapeng <jiapeng.chong@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver can call card->isac.release() function from an atomic
context.
Fix this by calling this function after releasing the lock.
The following log reveals it:
[ 44.168226 ] BUG: sleeping function called from invalid context at kernel/workqueue.c:3018
[ 44.168941 ] in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 5475, name: modprobe
[ 44.169574 ] INFO: lockdep is turned off.
[ 44.169899 ] irq event stamp: 0
[ 44.170160 ] hardirqs last enabled at (0): [<0000000000000000>] 0x0
[ 44.170627 ] hardirqs last disabled at (0): [<ffffffff814209ed>] copy_process+0x132d/0x3e00
[ 44.171240 ] softirqs last enabled at (0): [<ffffffff81420a1a>] copy_process+0x135a/0x3e00
[ 44.171852 ] softirqs last disabled at (0): [<0000000000000000>] 0x0
[ 44.172318 ] Preemption disabled at:
[ 44.172320 ] [<ffffffffa009b0a9>] nj_release+0x69/0x500 [netjet]
[ 44.174441 ] Call Trace:
[ 44.174630 ] dump_stack_lvl+0xa8/0xd1
[ 44.174912 ] dump_stack+0x15/0x17
[ 44.175166 ] ___might_sleep+0x3a2/0x510
[ 44.175459 ] ? nj_release+0x69/0x500 [netjet]
[ 44.175791 ] __might_sleep+0x82/0xe0
[ 44.176063 ] ? start_flush_work+0x20/0x7b0
[ 44.176375 ] start_flush_work+0x33/0x7b0
[ 44.176672 ] ? trace_irq_enable_rcuidle+0x85/0x170
[ 44.177034 ] ? kasan_quarantine_put+0xaa/0x1f0
[ 44.177372 ] ? kasan_quarantine_put+0xaa/0x1f0
[ 44.177711 ] __flush_work+0x11a/0x1a0
[ 44.177991 ] ? flush_work+0x20/0x20
[ 44.178257 ] ? lock_release+0x13c/0x8f0
[ 44.178550 ] ? __kasan_check_write+0x14/0x20
[ 44.178872 ] ? do_raw_spin_lock+0x148/0x360
[ 44.179187 ] ? read_lock_is_recursive+0x20/0x20
[ 44.179530 ] ? __kasan_check_read+0x11/0x20
[ 44.179846 ] ? do_raw_spin_unlock+0x55/0x900
[ 44.180168 ] ? ____kasan_slab_free+0x116/0x140
[ 44.180505 ] ? _raw_spin_unlock_irqrestore+0x41/0x60
[ 44.180878 ] ? skb_queue_purge+0x1a3/0x1c0
[ 44.181189 ] ? kfree+0x13e/0x290
[ 44.181438 ] flush_work+0x17/0x20
[ 44.181695 ] mISDN_freedchannel+0xe8/0x100
[ 44.182006 ] isac_release+0x210/0x260 [mISDNipac]
[ 44.182366 ] nj_release+0xf6/0x500 [netjet]
[ 44.182685 ] nj_remove+0x48/0x70 [netjet]
[ 44.182989 ] pci_device_remove+0xa9/0x250
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bridging, and possibly other upper stack gizmos, adds the
lower device's netdev->dev_addr to its own uc list, and
then requests it be deleted when the upper bridge device is
removed. This delete request also happens with the bridging
vlan_filtering is enabled and then disabled.
Bonding has a similar behavior with the uc list, but since it
also uses set_mac to manage netdev->dev_addr, it doesn't have
the same the failure case.
Because we store our netdev->dev_addr in our uc list, we need
to ignore the delete request from dev_uc_sync so as to not
lose the address and all hope of communicating. Note that
ndo_set_mac_address is expressly changing netdev->dev_addr,
so no limitation is set there.
Fixes: 2a654540be10 ("ionic: Add Rx filter and rx_mode ndo support")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use dev_addr_set() instead of writing directly to netdev->dev_addr
in various misc and old drivers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
8390 contains a lot of loops assigning netdev->dev_addr
byte by byte. Convert what's possible directly to
eth_hw_addr_set(), use local buf in other places.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Consify temporary variables pointing to netdev->dev_addr.
A few places need local storage but pretty simple conversion
over all. Note that macaddr[] is an array of ints, so we need
to keep the loops.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Consify the casts of netdev->dev_addr.
Convert pointless to eth_hw_addr_set() where possible.
Use local buffers in a number of places.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tg3 does various forms of direct writes to netdev->dev_addr.
Use a local buffer. Make sure local buffer is aligned since
eth_platform_get_mac_address() may call ether_addr_copy().
tg3_get_device_address() returns whenever it finds a method
that found a valid address. Instead of modifying all the exit
points pass the buffer from the outside and commit the address
in the caller.
Constify the argument of the set addr helper.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
forcedeth writes to dev_addr byte by byte, make it use
a local buffer instead. Commit the changes with
eth_hw_addr_set() at the end.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Zhu Yanjun <zyjzyj2000@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add additional flow steering priorities in the RDMA namespace.
This allows adding flow counters to count filtered RDMA traffic and then
continue processing in the regular RDMA steering flow.
Signed-off-by: Aharon Landau <aharonl@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Mark Zhang <markzhang@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
|
|
Even though it may be user-space's fault for this error (some application
terminated or crashed without cleaning up it's endpoint), the rpmsg
communication should not overflow the syslog with too many messages.
A dev_warn_ratelimited() seems like a good alternative in case this can
occur.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210928132902.1594277-1-aardelean@deviqon.com
|
|
Remove including <linux/of_device.h> that don't need it.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210811123125.143-1-caihuoqing@baidu.com
|
|
Fix error handling in mana_create_rxq() when
cq->gdma_id >= gc->max_num_cqs.
Fixes: ca9c54d2d6a5 ("net: mana: Add a driver for Microsoft Azure Network Adapter (MANA)")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Link: https://lore.kernel.org/r/1633698691-31721-1-git-send-email-haiyangz@microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
mlxsw is using helpers to get / set fields in messages exchanged with
the device. It is possible that some fields are only set or only get.
This causes LLVM to emit warnings such as the following when building
with W=1 [1]:
drivers/net/ethernet/mellanox/mlxsw/core_acl_flex_actions.c:2022:1: warning: unused function 'mlxsw_afa_sampler_mirror_agent_get'
The fact that some fields are only set or only get is very much
intentional and not indicative of functions that need to be removed.
Therefore, annotate the item helpers with '__maybe_unused' to suppress
these warnings.
[1] https://lkml.org/lkml/2021/9/29/685
Cc: Nathan Chancellor <nathan@kernel.org>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20211008132315.90211-1-idosch@idosch.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The cmtp_add_connection() would add a cmtp session to a controller
and run a kernel thread to process cmtp.
__module_get(THIS_MODULE);
session->task = kthread_run(cmtp_session, session, "kcmtpd_ctr_%d",
session->num);
During this process, the kernel thread would call detach_capi_ctr()
to detach a register controller. if the controller
was not attached yet, detach_capi_ctr() would
trigger an array-index-out-bounds bug.
[ 46.866069][ T6479] UBSAN: array-index-out-of-bounds in
drivers/isdn/capi/kcapi.c:483:21
[ 46.867196][ T6479] index -1 is out of range for type 'capi_ctr *[32]'
[ 46.867982][ T6479] CPU: 1 PID: 6479 Comm: kcmtpd_ctr_0 Not tainted
5.15.0-rc2+ #8
[ 46.869002][ T6479] Hardware name: QEMU Standard PC (i440FX + PIIX,
1996), BIOS 1.14.0-2 04/01/2014
[ 46.870107][ T6479] Call Trace:
[ 46.870473][ T6479] dump_stack_lvl+0x57/0x7d
[ 46.870974][ T6479] ubsan_epilogue+0x5/0x40
[ 46.871458][ T6479] __ubsan_handle_out_of_bounds.cold+0x43/0x48
[ 46.872135][ T6479] detach_capi_ctr+0x64/0xc0
[ 46.872639][ T6479] cmtp_session+0x5c8/0x5d0
[ 46.873131][ T6479] ? __init_waitqueue_head+0x60/0x60
[ 46.873712][ T6479] ? cmtp_add_msgpart+0x120/0x120
[ 46.874256][ T6479] kthread+0x147/0x170
[ 46.874709][ T6479] ? set_kthread_struct+0x40/0x40
[ 46.875248][ T6479] ret_from_fork+0x1f/0x30
[ 46.875773][ T6479]
Signed-off-by: Xiaolong Huang <butterflyhuangxx@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20211008065830.305057-1-butterflyhuangxx@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove the redundant check of (tg3_asic_rev(tp) == ASIC_REV_5705) after
it is checked to be true.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20211008063147.1421-1-sakiwit@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pull s390 fixes from Vasily Gorbik:
- Fix potential memory leak on a error path in eBPF
- Fix handling of zpci device on reserve
* tag 's390-5.15-5' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/pci: fix zpci_zdev_put() on reserve
bpf, s390: Fix potential memory leak about jit_data
|
|
Similar to commit 6087175b7991 ("net: dsa: mt7530: use independent VLAN
learning on VLAN-unaware bridges"), software forwarding between an
unoffloaded LAG port (a bonding interface with an unsupported policy)
and a mv88e6xxx user port directly under a bridge is broken.
We adopt the same strategy, which is to make the standalone ports not
find any ATU entry learned on a bridge port.
Theory: the mv88e6xxx ATU is looked up by FID and MAC address. There are
as many FIDs as VIDs (4096). The FID is derived from the VID when
possible (the VTU maps a VID to a FID), with a fallback to the port
based default FID value when not (802.1Q Mode is disabled on the port,
or the classified VID isn't present in the VTU).
The mv88e6xxx driver makes the following use of FIDs and VIDs:
- the port's DefaultVID (to which untagged & pvid-tagged packets get
classified) is 0 and is absent from the VTU, so this kind of packets is
processed in FID 0, the default FID assigned by mv88e6xxx_setup_port.
- every time a bridge VLAN is created, mv88e6xxx_port_vlan_join() ->
mv88e6xxx_atu_new() associates a FID with that VID which increases
linearly starting from 1. Like this:
bridge vlan add dev lan0 vid 100 # FID 1
bridge vlan add dev lan1 vid 100 # still FID 1
bridge vlan add dev lan2 vid 1024 # FID 2
The FID allocation made by the driver is sub-optimal for the following
reasons:
(a) A standalone port has a DefaultPVID of 0 and a default FID of 0 too.
A VLAN-unaware bridged port has a DefaultPVID of 0 and a default FID
of 0 too. The difference is that the bridged ports may learn ATU
entries, while the standalone port has the requirement that it must
not, and must not find them either. Standalone ports must not use
the same FID as ports belonging to a bridge. All standalone ports
can use the same FID, since the ATU will never have an entry in
that FID.
(b) Multiple VLAN-unaware bridges will all use a DefaultPVID of 0 and a
default FID of 0 on all their ports. The FDBs will not be isolated
between these bridges. Every VLAN-unaware bridge must use the same
FID on all its ports, different from the FID of other bridge ports.
(c) Each bridge VLAN uses a unique FID which is useful for Independent
VLAN Learning, but the same VLAN ID on multiple VLAN-aware bridges
will result in the same FID being used by mv88e6xxx_atu_new().
The correct behavior is for VLAN 1 in br0 to have a different FID
compared to VLAN 1 in br1.
This patch cannot fix all the above. Traditionally the DSA framework did
not care about this, and the reality is that DSA core involvement is
needed for the aforementioned issues to be solved. The only thing we can
solve here is an issue which does not require API changes, and that is
issue (a), aka use a different FID for standalone ports vs ports under
VLAN-unaware bridges.
The first step is deciding what VID and FID to use for standalone ports,
and what VID and FID for bridged ports. The 0/0 pair for standalone
ports is what they used up till now, let's keep using that. For bridged
ports, there are 2 cases:
- VLAN-aware ports will never end up using the port default FID, because
packets will always be classified to a VID in the VTU or dropped
otherwise. The FID is the one associated with the VID in the VTU.
- On VLAN-unaware ports, we _could_ leave their DefaultVID (pvid) at
zero (just as in the case of standalone ports), and just change the
port's default FID from 0 to a different number (say 1).
However, Tobias points out that there is one more requirement to cater to:
cross-chip bridging. The Marvell DSA header does not carry the FID in
it, only the VID. So once a packet crosses a DSA link, if it has a VID
of zero it will get classified to the default FID of that cascade port.
Relying on a port default FID for upstream cascade ports results in
contradictions: a default FID of 0 breaks ATU isolation of bridged ports
on the downstream switch, a default FID of 1 breaks standalone ports on
the downstream switch.
So not only must standalone ports have different FIDs compared to
bridged ports, they must also have different DefaultVID values.
IEEE 802.1Q defines two reserved VID values: 0 and 4095. So we simply
choose 4095 as the DefaultVID of ports belonging to VLAN-unaware
bridges, and VID 4095 maps to FID 1.
For the xmit operation to look up the same ATU database, we need to put
VID 4095 in DSA tags sent to ports belonging to VLAN-unaware bridges
too. All shared ports are configured to map this VID to the bridging
FID, because they are members of that VLAN in the VTU. Shared ports
don't need to have 802.1QMode enabled in any way, they always parse the
VID from the DSA header, they don't need to look at the 802.1Q header.
We install VID 4095 to the VTU in mv88e6xxx_setup_port(), with the
mention that mv88e6xxx_vtu_setup() which was located right below that
call was flushing the VTU so those entries wouldn't be preserved.
So we need to relocate the VTU flushing prior to the port initialization
during ->setup(). Also note that this is why it is safe to assume that
VID 4095 will get associated with FID 1: the user ports haven't been
created, so there is no avenue for the user to create a bridge VLAN
which could otherwise race with the creation of another FID which would
otherwise use up the non-reserved FID value of 1.
[ Currently mv88e6xxx_port_vlan_join() doesn't have the option of
specifying a preferred FID, it always calls mv88e6xxx_atu_new(). ]
mv88e6xxx_port_db_load_purge() is the function to access the ATU for
FDB/MDB entries, and it used to determine the FID to use for
VLAN-unaware FDB entries (VID=0) using mv88e6xxx_port_get_fid().
But the driver only called mv88e6xxx_port_set_fid() once, during probe,
so no surprises, the port FID was always 0, the call to get_fid() was
redundant. As much as I would have wanted to not touch that code, the
logic is broken when we add a new FID which is not the port-based
default. Now the port-based default FID only corresponds to standalone
ports, and FDB/MDB entries belong to the bridging service. So while in
the future, when the DSA API will support FDB isolation, we will have to
figure out the FID based on the bridge number, for now there's a single
bridging FID, so hardcode that.
Lastly, the tagger needs to check, when it is transmitting a VLAN
untagged skb, whether it is sending it towards a bridged or a standalone
port. When we see it is bridged we assume the bridge is VLAN-unaware.
Not because it cannot be VLAN-aware but:
- if we are transmitting from a VLAN-aware bridge we are likely doing so
using TX forwarding offload. That code path guarantees that skbs have
a vlan hwaccel tag in them, so we would not enter the "else" branch
of the "if (skb->protocol == htons(ETH_P_8021Q))" condition.
- if we are transmitting on behalf of a VLAN-aware bridge but with no TX
forwarding offload (no PVT support, out of space in the PVT, whatever),
we would indeed be transmitting with VLAN 4095 instead of the bridge
device's pvid. However we would be injecting a "From CPU" frame, and
the switch won't learn from that - it only learns from "Forward" frames.
So it is inconsequential for address learning. And VLAN 4095 is
absolutely enough for the frame to exit the switch, since we never
remove that VLAN from any port.
Fixes: 57e661aae6a8 ("net: dsa: mv88e6xxx: Link aggregation support")
Reported-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The VLAN support in mv88e6xxx has a loaded history. Commit 2ea7a679ca2a
("net: dsa: Don't add vlans when vlan filtering is disabled") noticed
some issues with VLAN and decided the best way to deal with them was to
make the DSA core ignore VLANs added by the bridge while VLAN awareness
is turned off. Those issues were never explained, just presented as
"at least one corner case".
That approach had problems of its own, presented by
commit 54a0ed0df496 ("net: dsa: provide an option for drivers to always
receive bridge VLANs") for the DSA core, followed by
commit 1fb74191988f ("net: dsa: mv88e6xxx: fix vlan setup") which
applied ds->configure_vlan_while_not_filtering = true for mv88e6xxx in
particular.
We still don't know what corner case Andrew saw when he wrote
commit 2ea7a679ca2a ("net: dsa: Don't add vlans when vlan filtering is
disabled"), but Tobias now reports that when we use TX forwarding
offload, pinging an external station from the bridge device is broken if
the front-facing DSA user port has flooding turned off. The full
description is in the link below, but for short, when a mv88e6xxx port
is under a VLAN-unaware bridge, it inherits that bridge's pvid.
So packets ingressing a user port will be classified to e.g. VID 1
(assuming that value for the bridge_default_pvid), whereas when
tag_dsa.c xmits towards a user port, it always sends packets using a VID
of 0 if that port is standalone or under a VLAN-unaware bridge - or at
least it did so prior to commit d82f8ab0d874 ("net: dsa: tag_dsa:
offload the bridge forwarding process").
In any case, when there is a conversation between the CPU and a station
connected to a user port, the station's MAC address is learned in VID 1
but the CPU tries to transmit through VID 0. The packets reach the
intended station, but via flooding and not by virtue of matching the
existing ATU entry.
DSA has established (and enforced in other drivers: sja1105, felix,
mt7530) that a VLAN-unaware port should use a private pvid, and not
inherit the one from the bridge. The bridge's pvid should only be
inherited when that bridge is VLAN-aware, so all state transitions need
to be handled. On the other hand, all bridge VLANs should sit in the VTU
starting with the moment when the bridge offloads them via switchdev,
they are just not used.
This solves the problem that Tobias sees because packets ingressing on
VLAN-unaware user ports now get classified to VID 0, which is also the
VID used by tag_dsa.c on xmit.
Fixes: d82f8ab0d874 ("net: dsa: tag_dsa: offload the bridge forwarding process")
Link: https://patchwork.kernel.org/project/netdevbpf/patch/20211003222312.284175-2-vladimir.oltean@nxp.com/#24491503
Reported-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
No facility requests the include of rpmsg_internal.h header file.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210712123752.10449-2-arnaud.pouliquen@foss.st.com
|
|
Correct a number of misspelled words and remove any words that were
duplicated in the PCI tree. No change to functionality intended.
Link: https://lore.kernel.org/r/20211006233827.147328-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Pull xen fixes from Juergen Gross:
- fix two minor issues in the Xen privcmd driver plus a cleanup patch
for that driver
- fix multiple issues related to running as PVH guest and some related
earlyprintk fixes for other Xen guest types
- fix an issue introduced in 5.15 the Xen balloon driver
* tag 'for-linus-5.15b-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/balloon: fix cancelled balloon action
xen/x86: adjust data placement
x86/PVH: adjust function/data placement
xen/x86: hook up xen_banner() also for PVH
xen/x86: generalize preferred console model from PV to PVH Dom0
xen/x86: make "earlyprintk=xen" work for HVM/PVH DomU
xen/x86: allow "earlyprintk=xen" to work for PV Dom0
xen/x86: make "earlyprintk=xen" work better for PVH Dom0
xen/x86: allow PVH Dom0 without XEN_PV=y
xen/x86: prevent PVH type from getting clobbered
xen/privcmd: drop "pages" parameter from xen_remap_pfn()
xen/privcmd: fix error handling in mmap-resource processing
xen/privcmd: replace kcalloc() by kvcalloc() when allocating empty pages
|
|
Use the devm_platform_ioremap_resource() helper instead of calling
platform_get_resource() and devm_ioremap_resource() separately.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add a driver to hook into panic notifiers and print machine check
status for debugging. Status information is retrieved via SMC. This
is supported by upstream ARM Trusted Firmware.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Merge fixes to avoid binding schema warnings.
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Pull asm-generic fixes from Arnd Bergmann:
"There is one build fix for Arm platforms that ended up impacting most
architectures because of the way the drivers/firmware Kconfig file is
wired up:
The CONFIG_QCOM_SCM dependency have caused a number of randconfig
regressions over time, and some still remain in v5.15-rc4. The fix we
agreed on in the end is to make this symbol selected by any driver
using it, and then building it even for non-Arm platforms with
CONFIG_COMPILE_TEST.
To make this work on all architectures, the drivers/firmware/Kconfig
file needs to be included for all architectures to make the symbol
itself visible.
In a separate discussion, we found that a sound driver patch that is
pending for v5.16 needs the same change to include this Kconfig file,
so the easiest solution seems to have my Kconfig rework included in
v5.15.
Finally, the branch also includes a small unrelated build fix for
NOMMU architectures"
Link: https://lore.kernel.org/all/20210928153508.101208f8@canb.auug.org.au/
Link: https://lore.kernel.org/all/20210928075216.4193128-1-arnd@kernel.org/
Link: https://lore.kernel.org/all/20211007151010.333516-1-arnd@kernel.org/
* tag 'asm-generic-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic/io.h: give stub iounmap() on !MMU same prototype as elsewhere
qcom_scm: hide Kconfig symbol
firmware: include drivers/firmware/Kconfig unconditionally
|
Ansuel Smith
Juhee Kang
Shannon Nelson
Zheyu Ma
Linus Torvalds
Sam Protsenko
Sam Ravnborg
Dmitry Baryshkov
Søren Andersen
Xuan Zhuo
Florian Fainelli
chongjiapeng
Jakub Kicinski
Aharon Landau
Alexandru Ardelean
Cai Huoqing
Haiyang Zhang
Ido Schimmel
Xiaolong Huang
Jean Sacren
Vladimir Oltean
Arnaud Pouliquen
Krzysztof Wilczyński
Mikko Perttunen
Rob Herring