| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Currently, iommu_init_ga() checks and disables IOMMU VAPIC support
(i.e. AMD AVIC support in IOMMU) when GAMSup feature bit is not set.
However it forgets to clear IRQ_POSTING_CAP from the previously set
amd_iommu_irq_ops.capability.
This triggers an invalid page fault bug during guest VM warm reboot
if AVIC is enabled since the irq_remapping_cap(IRQ_POSTING_CAP) is
incorrectly set, and crash the system with the following kernel trace.
BUG: unable to handle page fault for address: 0000000000400dd8
RIP: 0010:amd_iommu_deactivate_guest_mode+0x19/0xbc
Call Trace:
svm_set_pi_irte_mode+0x8a/0xc0 [kvm_amd]
? kvm_make_all_cpus_request_except+0x50/0x70 [kvm]
kvm_request_apicv_update+0x10c/0x150 [kvm]
svm_toggle_avic_for_irq_window+0x52/0x90 [kvm_amd]
svm_enable_irq_window+0x26/0xa0 [kvm_amd]
vcpu_enter_guest+0xbbe/0x1560 [kvm]
? avic_vcpu_load+0xd5/0x120 [kvm_amd]
? kvm_arch_vcpu_load+0x76/0x240 [kvm]
? svm_get_segment_base+0xa/0x10 [kvm_amd]
kvm_arch_vcpu_ioctl_run+0x103/0x590 [kvm]
kvm_vcpu_ioctl+0x22a/0x5d0 [kvm]
__x64_sys_ioctl+0x84/0xc0
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xae
Fixes by moving the initializing of AMD IOMMU interrupt remapping mode
(amd_iommu_guest_ir) earlier before setting up the
amd_iommu_irq_ops.capability with appropriate IRQ_POSTING_CAP flag.
[joro: Squashed the two patches and limited
check_features_on_all_iommus() to CONFIG_IRQ_REMAP
to fix a compile warning.]
Signed-off-by: Wei Huang <wei.huang2@amd.com>
Co-developed-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Link: https://lore.kernel.org/r/20210820202957.187572-2-suravee.suthikulpanit@amd.com
Link: https://lore.kernel.org/r/20210820202957.187572-3-suravee.suthikulpanit@amd.com
Fixes: 8bda0cfbdc1a ("iommu/amd: Detect and initialize guest vAPIC log")
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
On some Cherry Trail devices, DisplayPort over Type-C is supported through
a USB-PD microcontroller (e.g. a fusb302) + a mux to switch the superspeed
datalines between USB-3 and DP (e.g. a pi3usb30532). The kernel in this
case does the PD/alt-mode negotiation itself, rather then everything being
handled in firmware.
So the kernel itself picks an alt-mode, tells the Type-C "dongle" to switch
to DP mode and sets the mux accordingly. In this setup the HPD pin is not
connected, so the i915 driver needs to respond to a software event and scan
the DP port for changes manually.
This commit adds support for this. Together with the recent addition of
DP alt-mode support to the Type-C subsystem this makes DP over Type-C
work on these devices.
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210817215201.795062-7-hdegoede@redhat.com
|
|
On Intel platforms we know that the ACPI connector device
node order will follow the order the driver (i915) decides.
The decision is made using the custom Intel ACPI OpRegion
(intel_opregion.c), though the driver does not actually know
that the values it sends to ACPI there are used for
associating a device node for the connectors, and assigning
address for them.
In reality that custom Intel ACPI OpRegion actually violates
ACPI specification (we supply dynamic information to objects
that are defined static, for example _ADR), however, it
makes assigning correct connector node for a connector entry
straightforward (it's one-on-one mapping).
Changes in v2 (Hans de goede):
- Take a reference on the fwnode which we assign to the connector,
for ACPI nodes this is a no-op but in the future we may see
software-fwnodes assigned to connectors which are ref-counted.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210817215201.795062-6-hdegoede@redhat.com
|
|
parisc build test images fail to compile with the following error.
drivers/parisc/dino.c:160:12: error:
'pci_dev_is_behind_card_dino' defined but not used
Move the function just ahead of its only caller to avoid the error.
Fixes: 5fa1659105fa ("parisc: Disable HP HSC-PCI Cards to prevent kernel crash")
Cc: Helge Deller <deller@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Building alpha:allmodconfig results in the following error.
drivers/net/ethernet/amd/ni65.c: In function 'ni65_stop_start':
drivers/net/ethernet/amd/ni65.c:751:37: error:
cast from pointer to integer of different size
buffer[i] = (u32) isa_bus_to_virt(tmdp->u.buffer);
'buffer[]' is declared as unsigned long, so replace the typecast to u32
with a typecast to unsigned long to fix the problem.
Cc: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previous patch addressed the situation of having some free resources for
xdp tx but not enough for one tx queue per CPU. This patch address the
worst case of not having resources at all for xdp tx.
Instead of using queues dedicated to xdp, normal queues used by network
stack are shared for both cases, using __netif_tx_lock for
synchronization. Also queue stop/restart must be considered in the xdp
path to avoid freezing the queue.
This is not the ideal situation we might want to be, and a performance
penalty is expected both for normal and xdp traffic, but at least XDP
will work in all possible situations (with a warning in the logs),
improving a bit the pain of not knowing in what situations we can use it
and in what situations we cannot.
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If there are not enough resources to allocate one TX queue per core for
XDP TX it was completely disabled.
This patch implements a fallback solution for sharing the available
queues using __netif_tx_lock for synchronization. In the normal case that
there is one TX queue per CPU, no locking is done, as it was before.
With this fallback solution, XDP TX will work in much more cases that
were failing, specially in machines with many CPUs. It's hard for XDP
users to know what features are supported across different NICs and
configurations, so they will benefit on having wider support.
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use __maybe_unused for noirq_suspend()/noirq_resume() hooks to avoid
build warning with !CONFIG_PM_SLEEP:
>> drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c:796:12: error: 'stmmac_pltfr_noirq_resume' defined but not used [-Werror=unused-function]
796 | static int stmmac_pltfr_noirq_resume(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~~~~~
>> drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c:775:12: error: 'stmmac_pltfr_noirq_suspend' defined but not used [-Werror=unused-function]
775 | static int stmmac_pltfr_noirq_suspend(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Fixes: 276aae377206 ("net: stmmac: fix system hang caused by eee_ctrl_timer during suspend/resume")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
plat_dev->dev->platform_data is released by platform_device_unregister(),
use of pclk and hclk is a use-after-free. Since device unregister won't
need a clk device we adjust the function call sequence to fix this issue.
[ 31.261225] BUG: KASAN: use-after-free in macb_remove+0x77/0xc6 [macb_pci]
[ 31.275563] Freed by task 306:
[ 30.276782] platform_device_release+0x25/0x80
Suggested-by: Nicolas Ferre <Nicolas.Ferre@microchip.com>
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If a failover occurs before a login response is received, the login
response buffer maybe undefined. Check that there was no failover
before accessing the login response buffer.
Fixes: 032c5e82847a ("Driver for IBM System i/p VNIC protocol")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the sendmsg() call in vhost_tx_batch() fails, both the 'batched_xdp'
and 'done_idx' indexes are left unchanged. If such failure happens
when batched_xdp == VHOST_NET_BATCH, the next call to
vhost_net_build_xdp() will access and write memory outside the xdp
buffers area.
Since sendmsg() can only error with EBADFD, this change addresses the
issue explicitly freeing the XDP buffers batch on error.
Fixes: 0a0be13b8fe2 ("vhost_net: batch submitting XDP buffers to underlayer sockets")
Suggested-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The rtc-rx8010 uses the I2C regmap but doesn't select it in Kconfig so
depending on the configuration the build may fail. Fix it.
Signed-off-by: Yu-Tung Chang <mtwget@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210830052532.40356-1-mtwget@gmail.com
|
|
On some MST docking stations, rx_info can only be read after
RepeaterAuth_Send_ReceiverID_List and the RxStatus READY bit is set
otherwise the read will return -EIO.
This behavior causes the mst stream type1 capability test to fail to
read rx_info and determine if the topology supports type1 and fallback
to type0.
To fix this, check for type1 capability when we receive rx_info within
the AKE flow when we read RepeaterAuth_Send_ReceiverID_List instead
of an explicit read just for type1 capability checking.
This does require moving where we set stream_types to after
hdcp2_authenticate_sink() when we get rx_info but this occurs before we
do hdcp2_propagate_stream_management_info.
Also, legacy HDCP 2.0/2.1 are not type 1 capable either so check for
that as well.
Changes since v5:
- rename intel_set_stream_types() to intel_hdcp_prepare_streams()
(Anshuman)
Changes since v4:
- move topology_type1_capable to intel_digital_port and rename it as
hdcp_mst_type1_capable (Anshuman)
- make a helper function intel_set_stream_types() to set stream types
in hdcp2_authenticate_and_encrypt() (Anshuman)
- break on failure to set stream types and retry instead of returning
- remove no longer used declaration for streams_type1_capable()
Changes since v2:
- Remove no longer used variables in _intel_hdcp2_enable()
Signed-off-by: Juston Li <juston.li@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Tested-by: Suraj K <suraj.kandpal@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210819184835.1181323-4-juston.li@intel.com
|
|
When reading RepeaterAuth_Send_ReceiverID_List, RxInfo is read by itself
once to retrieve the DEVICE_COUNT to calculate the size of the
ReceiverID list then read a second time as a part of reading ReceiverID
list.
On some MST docking stations, RxInfo can only be read after the RxStatus
READY bit is set otherwise the read will return -EIO. The spec states that
the READY bit should be cleared as soon as RxInfo has been read.
In this case, the first RxInfo read succeeds but after the READY bit is
cleared, the second read fails.
Fix it by reading RxInfo once and storing it before reading the rest of
RepeaterAuth_Send_ReceiverID_List once we know the size.
Modify get_receiver_id_list_size() to read and store RxInfo in the
message buffer and also parse DEVICE_COUNT so we know the size of
RepeaterAuth_Send_ReceiverID_List.
Afterwards, retrieve the rest of the message at the offset for
seq_num_V.
Changes in v5:
- Don't change the offset define for Send_ReceiverID_List
When reading, update message offset to account for RxInfo being read
Changes in v4:
- rebase and edit commit message
Changes in v3:
- remove comment
Changes in v2:
- remove unnecessary moving of drm_i915_private from patch 1
Signed-off-by: Juston Li <juston.li@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Tested-by: Suraj K <suraj.kandpal@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210819184835.1181323-3-juston.li@intel.com
|
|
Update cp_irq_count_cached when reading messages rather than when
writing a message to make sure the value is up to date and not
stale from a previously handled CP_IRQ.
AKE flow doesn't always respond to a read with a ACK write msg.
E.g. AKE_Send_Pairing_Info will "timeout" because we received
a CP_IRQ for reading AKE_Send_H_Prime but no write occurred between that
and reading AKE_Send_Pairing_Info so cp_irq_count_cached is stale
causing the wait to return right away rather than waiting for a new
CP_IRQ.
Signed-off-by: Juston Li <juston.li@intel.com>
Acked-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Suraj K <suraj.kandpal@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210819184835.1181323-2-juston.li@intel.com
|
|
m68k, mips, s390, and sparc allmodconfig images fail to build with the
following error.
drivers/input/joystick/analog.c:160:2: error:
#warning Precise timer not defined for this architecture.
Remove architecture specific time handling code and always use ktime
functions to determine time deltas. Also remove the now useless use_ktime
kernel parameter.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Link: https://lore.kernel.org/r/20210907123734.21520-1-linux@roeck-us.net
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
drm-misc-next-fixes for v5.15:
- Fix ttm_bo_move_memcpy() when ttm_resource is subclassed.
- Small fixes to panfrost, mgag200, vc4.
- Small ttm compilation fixes.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/41ff5e54-0837-2226-a182-97ffd11ef01e@linux.intel.com
|
|
amd-drm-next-5.15-2021-09-01:
amdgpu:
- Misc cleanups, typo fixes
- EEPROM fix
- Add some new PCI IDs
- Scatter/Gather display support for Yellow Carp
- PCIe DPM fix for RKL platforms
- RAS fix
amdkfd:
- SVM fix
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210901214015.4488-1-alexander.deucher@amd.com
|
|
Pull chrome platform updates from Benson Leung:
"cros_ec_typec:
- make the cros_ec_typec driver to use the pre-existing
cros_ec_check_features() function
sensorhub:
- add trace events for sample
misc:
- cros_ec_proto - re-send commands in the event of a timeout (for the
FPMCU)
- fix warnings in cros_ec_trace related to format output"
* tag 'tag-chrome-platform-for-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
platform/chrome: cros_ec_trace: Fix format warnings
platform/chrome: cros_ec_typec: Use existing feature check
platform/chrome: cros_ec_proto: Send command again when timeout occurs
platform/chrome: sensorhub: Add trace events for sample
|
|
Pull more power management updates from Rafael Wysocki:
"These are mostly ARM cpufreq driver updates, including one new
MediaTek driver that has just passed all of the reviews, with the
addition of a revert of a recent intel_pstate commit, some core
cpufreq changes and a DT-related update of the operating performance
points (OPP) support code.
Specifics:
- Add new cpufreq driver for the MediaTek MT6779 platform called
mediatek-hw along with corresponding DT bindings (Hector.Yuan).
- Add DCVS interrupt support to the qcom-cpufreq-hw driver (Thara
Gopinath).
- Make the qcom-cpufreq-hw driver set the dvfs_possible_from_any_cpu
policy flag (Taniya Das).
- Blocklist more Qualcomm platforms in cpufreq-dt-platdev (Bjorn
Andersson).
- Make the vexpress cpufreq driver set the CPUFREQ_IS_COOLING_DEV
flag (Viresh Kumar).
- Add new cpufreq driver callback to allow drivers to register with
the Energy Model in a consistent way and make several drivers use
it (Viresh Kumar).
- Change the remaining users of the .ready() cpufreq driver callback
to move the code from it elsewhere and drop it from the cpufreq
core (Viresh Kumar).
- Revert recent intel_pstate change adding HWP guaranteed performance
change notification support to it that led to problems, because the
notification in question is triggered prematurely on some systems
(Rafael Wysocki).
- Convert the OPP DT bindings to DT schema and clean them up while at
it (Rob Herring)"
* tag 'pm-5.15-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (23 commits)
Revert "cpufreq: intel_pstate: Process HWP Guaranteed change notification"
cpufreq: mediatek-hw: Add support for CPUFREQ HW
cpufreq: Add of_perf_domain_get_sharing_cpumask
dt-bindings: cpufreq: add bindings for MediaTek cpufreq HW
cpufreq: Remove ready() callback
cpufreq: sh: Remove sh_cpufreq_cpu_ready()
cpufreq: acpi: Remove acpi_cpufreq_cpu_ready()
cpufreq: qcom-hw: Set dvfs_possible_from_any_cpu cpufreq driver flag
cpufreq: blocklist more Qualcomm platforms in cpufreq-dt-platdev
cpufreq: qcom-cpufreq-hw: Add dcvs interrupt support
cpufreq: scmi: Use .register_em() to register with energy model
cpufreq: vexpress: Use .register_em() to register with energy model
cpufreq: scpi: Use .register_em() to register with energy model
dt-bindings: opp: Convert to DT schema
dt-bindings: Clean-up OPP binding node names in examples
ARM: dts: omap: Drop references to opp.txt
cpufreq: qcom-cpufreq-hw: Use .register_em() to register with energy model
cpufreq: omap: Use .register_em() to register with energy model
cpufreq: mediatek: Use .register_em() to register with energy model
cpufreq: imx6q: Use .register_em() to register with energy model
...
|
|
Pull more ACPI updates from Rafael Wysocki:
"These add ACPI support to the PCI VMD driver, improve suspend-to-idle
support for AMD platforms and update documentation.
Specifics:
- Add ACPI support to the PCI VMD driver (Rafael Wysocki)
- Rearrange suspend-to-idle support code to reflect the platform
firmware expectations on some AMD platforms (Mario Limonciello)
- Make SSDT overlays documentation follow the code documented by it
more closely (Andy Shevchenko)"
* tag 'acpi-5.15-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: PM: s2idle: Run both AMD and Microsoft methods if both are supported
Documentation: ACPI: Align the SSDT overlays file with the code
PCI: VMD: ACPI: Make ACPI companion lookup work for VMD bus
|
|
Include Christoph's rework of the dax_supported() helpers in the v5.15
libnvdimm update. This supports the ongoing dax-reflink enabling effort.
|
|
Merge more updates from Andrew Morton:
"147 patches, based on 7d2a07b769330c34b4deabeed939325c77a7ec2f.
Subsystems affected by this patch series: mm (memory-hotplug, rmap,
ioremap, highmem, cleanups, secretmem, kfence, damon, and vmscan),
alpha, percpu, procfs, misc, core-kernel, MAINTAINERS, lib,
checkpatch, epoll, init, nilfs2, coredump, fork, pids, criu, kconfig,
selftests, ipc, and scripts"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (94 commits)
scripts: check_extable: fix typo in user error message
mm/workingset: correct kernel-doc notations
ipc: replace costly bailout check in sysvipc_find_ipc()
selftests/memfd: remove unused variable
Kconfig.debug: drop selecting non-existing HARDLOCKUP_DETECTOR_ARCH
configs: remove the obsolete CONFIG_INPUT_POLLDEV
prctl: allow to setup brk for et_dyn executables
pid: cleanup the stale comment mentioning pidmap_init().
kernel/fork.c: unexport get_{mm,task}_exe_file
coredump: fix memleak in dump_vma_snapshot()
fs/coredump.c: log if a core dump is aborted due to changed file permissions
nilfs2: use refcount_dec_and_lock() to fix potential UAF
nilfs2: fix memory leak in nilfs_sysfs_delete_snapshot_group
nilfs2: fix memory leak in nilfs_sysfs_create_snapshot_group
nilfs2: fix memory leak in nilfs_sysfs_delete_##name##_group
nilfs2: fix memory leak in nilfs_sysfs_create_##name##_group
nilfs2: fix NULL pointer in nilfs_##name##_attr_release
nilfs2: fix memory leak in nilfs_sysfs_create_device_group
trap: cleanup trap_init()
init: move usermodehelper_enable() to populate_rootfs()
...
|
|
Find and verify PRMT before parsing it, which eliminates a
warning on machines without PRMT:
[ 7.197173] ACPI: PRMT not present
Fixes: cefc7ca46235 ("ACPI: PRM: implement OperationRegion handler for the PlatformRtMechanism subtype")
Signed-off-by: Aubrey Li <aubrey.li@linux.intel.com>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Cc: 5.14+ <stable@vger.kernel.org> # 5.14+
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
HZ unit conversion macros are available in units.h, use them and remove
the duplicate definition.
Link: https://lkml.kernel.org/r/20210816114732.1834145-11-daniel.lezcano@linaro.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Christian Eggers <ceggers@arri.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Lukasz Luba <lukasz.luba@arm.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
HZ unit conversion macros are available in units.h, use them and remove
the duplicate definition.
Link: https://lkml.kernel.org/r/20210816114732.1834145-10-daniel.lezcano@linaro.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Christian Eggers <ceggers@arri.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Lukasz Luba <lukasz.luba@arm.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
HZ unit conversion macros are available in units.h, use them and remove
the duplicate definition.
Link: https://lkml.kernel.org/r/20210816114732.1834145-9-daniel.lezcano@linaro.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Christian Eggers <ceggers@arri.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Lukasz Luba <lukasz.luba@arm.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
HZ unit conversion macros are available in units.h, use them and remove
the duplicate definition.
Link: https://lkml.kernel.org/r/20210816114732.1834145-8-daniel.lezcano@linaro.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Christian Eggers <ceggers@arri.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Lukasz Luba <lukasz.luba@arm.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
HZ unit conversion macros are available in units.h, use them and remove
the duplicate definition.
The new macro is an unsigned long. The code dealing with it is
considering as an unsigned long also.
Link: https://lkml.kernel.org/r/20210816114732.1834145-7-daniel.lezcano@linaro.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Christian Eggers <ceggers@arri.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Lukasz Luba <lukasz.luba@arm.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
HZ unit conversion macros are available in units.h, use them and remove
the duplicate definition.
Link: https://lkml.kernel.org/r/20210816114732.1834145-6-daniel.lezcano@linaro.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Christian Eggers <ceggers@arri.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Lukasz Luba <lukasz.luba@arm.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
HZ unit conversion macros are available in units.h, use them and remove
the duplicate definition.
The new macro has an unsigned long type.
All the code is dealing with unsigned long and the code using the macro is
doing a coercitive cast to unsigned long.
Link: https://lkml.kernel.org/r/20210816114732.1834145-5-daniel.lezcano@linaro.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Christian Eggers <ceggers@arri.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Lukasz Luba <lukasz.luba@arm.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
HZ unit conversion macros are available in units.h, use them and remove
the duplicate definition.
The new macro uses a unsigned long type which is already the type in the
current code via the 'freq' variable.
Link: https://lkml.kernel.org/r/20210816114732.1834145-4-daniel.lezcano@linaro.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Christian Eggers <ceggers@arri.de>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Lukasz Luba <lukasz.luba@arm.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently, the "auto-movable" online policy does not allow for hotplugged
KERNEL (ZONE_NORMAL) memory to increase the amount of MOVABLE memory we
can have, primarily, because there is no coordiantion across memory
devices and we don't want to create zone-imbalances accidentially when
unplugging memory.
However, within a single memory device it's different. Let's allow for
KERNEL memory within a dynamic memory group to allow for more MOVABLE
within the same memory group. The only thing we have to take care of is
that the managing driver avoids zone imbalances by unplugging MOVABLE
memory first, otherwise there can be corner cases where unplug of memory
could result in (accidential) zone imbalances.
virtio-mem is the only user of dynamic memory groups and recently added
support for prioritizing unplug of ZONE_MOVABLE over ZONE_NORMAL, so we
don't need a new toggle to enable it for dynamic memory groups.
We limit this handling to dynamic memory groups, because:
* We want to keep the runtime overhead for collecting stats when
onlining a single memory block small. We tend to have only a handful of
dynamic memory groups, but we can have quite some static memory groups
(e.g., 256 DIMMs).
* It doesn't make too much sense for static memory groups, as we try
onlining all applicable memory blocks either completely to ZONE_MOVABLE
or not. In ordinary operation, we won't have a mixture of zones within
a static memory group.
When adding memory to a dynamic memory group, we'll first online memory to
ZONE_MOVABLE as long as early KERNEL memory allows for it. Then, we'll
online the next unit(s) to ZONE_NORMAL, until we can online the next
unit(s) to ZONE_MOVABLE.
For a simple virtio-mem device with a MOVABLE:KERNEL ratio of 3:1, it will
result in a layout like:
[M][M][M][M][M][M][M][M][N][M][M][M][N][M][M][M]...
^ movable memory due to early kernel memory
^ allows for more movable memory ...
^-----^ ... here
^ allows for more movable memory ...
^-----^ ... here
While the created layout is sub-optimal when it comes to contiguous zones,
it gives us the maximum flexibility when dynamically growing/shrinking a
device; we can grow small VMs really big in small steps, and still shrink
reliably to e.g., 1/4 of the maximum VM size in this example, removing
full memory blocks along with meta data more reliably.
Mark dynamic memory groups in the xarray such that we can efficiently
iterate over them when collecting stats. In usual setups, we have one
virtio-mem device per NUMA node, and usually only a small number of NUMA
nodes.
Note: for now, there seems to be no compelling reason to make this
behavior configurable.
Link: https://lkml.kernel.org/r/20210806124715.17090-10-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Hui Zhu <teawater@gmail.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Marek Kedzierski <mkedzier@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Wei Yang <richard.weiyang@linux.alibaba.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Use memory groups to improve our "auto-movable" onlining policy:
1. For static memory groups (e.g., a DIMM), online a memory block MOVABLE
only if all other memory blocks in the group are either MOVABLE or could
be onlined MOVABLE. A DIMM will either be MOVABLE or not, not a mixture.
2. For dynamic memory groups (e.g., a virtio-mem device), online a
memory block MOVABLE only if all other memory blocks inside the
current unit are either MOVABLE or could be onlined MOVABLE. For a
virtio-mem device with a device block size with 512 MiB, all 128 MiB
memory blocks wihin a 512 MiB unit will either be MOVABLE or not, not
a mixture.
We have to pass the memory group to zone_for_pfn_range() to take the
memory group into account.
Note: for now, there seems to be no compelling reason to make this
behavior configurable.
Link: https://lkml.kernel.org/r/20210806124715.17090-9-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Hui Zhu <teawater@gmail.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Marek Kedzierski <mkedzier@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Wei Yang <richard.weiyang@linux.alibaba.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Let's use a single dynamic memory group.
Link: https://lkml.kernel.org/r/20210806124715.17090-8-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Hui Zhu <teawater@gmail.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Marek Kedzierski <mkedzier@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Wei Yang <richard.weiyang@linux.alibaba.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Although dax/kmem users often disable auto-onlining and instead online
memory manually (usually to ZONE_MOVABLE), there is still value in having
auto-onlining be aware of the relationship of memory blocks.
Let's treat one probed unit as a single static memory device, similar to a
single ACPI memory device.
Link: https://lkml.kernel.org/r/20210806124715.17090-7-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Hui Zhu <teawater@gmail.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Marek Kedzierski <mkedzier@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Wei Yang <richard.weiyang@linux.alibaba.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Let's group all memory we add for a single memory device - we want a
single node for that (which also seems to be the sane thing to do).
We won't care for now about memory that was already added to the system
(e.g., via e820) -- usually *all* memory of a memory device was already
added and we'll fail acpi_memory_enable_device().
Link: https://lkml.kernel.org/r/20210806124715.17090-6-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Hui Zhu <teawater@gmail.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Marek Kedzierski <mkedzier@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Wei Yang <richard.weiyang@linux.alibaba.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Let's track all present pages in each memory group. Especially, track
memory present in ZONE_MOVABLE and memory present in one of the kernel
zones (which really only is ZONE_NORMAL right now as memory groups only
apply to hotplugged memory) separately within a memory group, to prepare
for making smart auto-online decision for individual memory blocks within
a memory group based on group statistics.
Link: https://lkml.kernel.org/r/20210806124715.17090-5-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Hui Zhu <teawater@gmail.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Marek Kedzierski <mkedzier@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Wei Yang <richard.weiyang@linux.alibaba.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In our "auto-movable" memory onlining policy, we want to make decisions
across memory blocks of a single memory device. Examples of memory
devices include ACPI memory devices (in the simplest case a single DIMM)
and virtio-mem. For now, we don't have a connection between a single
memory block device and the real memory device. Each memory device
consists of 1..X memory block devices.
Let's logically group memory blocks belonging to the same memory device in
"memory groups". Memory groups can span multiple physical ranges and a
memory group itself does not contain any information regarding physical
ranges, only properties (e.g., "max_pages") necessary for improved memory
onlining.
Introduce two memory group types:
1) Static memory group: E.g., a single ACPI memory device, consisting
of 1..X memory resources. A memory group consists of 1..Y memory
blocks. The whole group is added/removed in one go. If any part
cannot get offlined, the whole group cannot be removed.
2) Dynamic memory group: E.g., a single virtio-mem device. Memory is
dynamically added/removed in a fixed granularity, called a "unit",
consisting of 1..X memory blocks. A unit is added/removed in one go.
If any part of a unit cannot get offlined, the whole unit cannot be
removed.
In case of 1) we usually want either all memory managed by ZONE_MOVABLE or
none. In case of 2) we usually want to have as many units as possible
managed by ZONE_MOVABLE. We want a single unit to be of the same type.
For now, memory groups are an internal concept that is not exposed to user
space; we might want to change that in the future, though.
add_memory() users can specify a mgid instead of a nid when passing the
MHP_NID_IS_MGID flag.
Link: https://lkml.kernel.org/r/20210806124715.17090-4-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Hui Zhu <teawater@gmail.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Marek Kedzierski <mkedzier@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Wei Yang <richard.weiyang@linux.alibaba.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Patch series "mm/memory_hotplug: "auto-movable" online policy and memory groups", v3.
I. Goal
The goal of this series is improving in-kernel auto-online support. It
tackles the fundamental problems that:
1) We can create zone imbalances when onlining all memory blindly to
ZONE_MOVABLE, in the worst case crashing the system. We have to know
upfront how much memory we are going to hotplug such that we can
safely enable auto-onlining of all hotplugged memory to ZONE_MOVABLE
via "online_movable". This is far from practical and only applicable in
limited setups -- like inside VMs under the RHV/oVirt hypervisor which
will never hotplug more than 3 times the boot memory (and the
limitation is only in place due to the Linux limitation).
2) We see more setups that implement dynamic VM resizing, hot(un)plugging
memory to resize VM memory. In these setups, we might hotplug a lot of
memory, but it might happen in various small steps in both directions
(e.g., 2 GiB -> 8 GiB -> 4 GiB -> 16 GiB ...). virtio-mem is the
primary driver of this upstream right now, performing such dynamic
resizing NUMA-aware via multiple virtio-mem devices.
Onlining all hotplugged memory to ZONE_NORMAL means we basically have
no hotunplug guarantees. Onlining all to ZONE_MOVABLE means we can
easily run into zone imbalances when growing a VM. We want a mixture,
and we want as much memory as reasonable/configured in ZONE_MOVABLE.
Details regarding zone imbalances can be found at [1].
3) Memory devices consist of 1..X memory block devices, however, the
kernel doesn't really track the relationship. Consequently, also user
space has no idea. We want to make per-device decisions.
As one example, for memory hotunplug it doesn't make sense to use a
mixture of zones within a single DIMM: we want all MOVABLE if
possible, otherwise all !MOVABLE, because any !MOVABLE part will easily
block the whole DIMM from getting hotunplugged.
As another example, virtio-mem operates on individual units that span
1..X memory blocks. Similar to a DIMM, we want a unit to either be all
MOVABLE or !MOVABLE. A "unit" can be thought of like a DIMM, however,
all units of a virtio-mem device logically belong together and are
managed (added/removed) by a single driver. We want as much memory of
a virtio-mem device to be MOVABLE as possible.
4) We want memory onlining to be done right from the kernel while adding
memory, not triggered by user space via udev rules; for example, this
is reqired for fast memory hotplug for drivers that add individual
memory blocks, like virito-mem. We want a way to configure a policy in
the kernel and avoid implementing advanced policies in user space.
The auto-onlining support we have in the kernel is not sufficient. All we
have is a) online everything MOVABLE (online_movable) b) online everything
!MOVABLE (online_kernel) c) keep zones contiguous (online). This series
allows configuring c) to mean instead "online movable if possible
according to the coniguration, driven by a maximum MOVABLE:KERNEL ratio"
-- a new onlining policy.
II. Approach
This series does 3 things:
1) Introduces the "auto-movable" online policy that initially operates on
individual memory blocks only. It uses a maximum MOVABLE:KERNEL ratio
to make a decision whether a memory block will be onlined to
ZONE_MOVABLE or not. However, in the basic form, hotplugged KERNEL
memory does not allow for more MOVABLE memory (details in the
patches). CMA memory is treated like MOVABLE memory.
2) Introduces static (e.g., DIMM) and dynamic (e.g., virtio-mem) memory
groups and uses group information to make decisions in the
"auto-movable" online policy across memory blocks of a single memory
device (modeled as memory group). More details can be found in patch
#3 or in the DIMM example below.
3) Maximizes ZONE_MOVABLE memory within dynamic memory groups, by
allowing ZONE_NORMAL memory within a dynamic memory group to allow for
more ZONE_MOVABLE memory within the same memory group. The target use
case is dynamic VM resizing using virtio-mem. See the virtio-mem
example below.
I remember that the basic idea of using a ratio to implement a policy in
the kernel was once mentioned by Vitaly Kuznetsov, but I might be wrong (I
lost the pointer to that discussion).
For me, the main use case is using it along with virtio-mem (and DIMMs /
ppc64 dlpar where necessary) for dynamic resizing of VMs, increasing the
amount of memory we can hotunplug reliably again if we might eventually
hotplug a lot of memory to a VM.
III. Target Usage
The target usage will be:
1) Linux boots with "mhp_default_online_type=offline"
2) User space (e.g., systemd unit) configures memory onlining (according
to a config file and system properties), for example:
* Setting memory_hotplug.online_policy=auto-movable
* Setting memory_hotplug.auto_movable_ratio=301
* Setting memory_hotplug.auto_movable_numa_aware=true
3) User space enabled auto onlining via "echo online >
/sys/devices/system/memory/auto_online_blocks"
4) User space triggers manual onlining of all already-offline memory
blocks (go over offline memory blocks and set them to "online")
IV. Example
For DIMMs, hotplugging 4 GiB DIMMs to a 4 GiB VM with a configured ratio of
301% results in the following layout:
Memory block 0-15: DMA32 (early)
Memory block 32-47: Normal (early)
Memory block 48-79: Movable (DIMM 0)
Memory block 80-111: Movable (DIMM 1)
Memory block 112-143: Movable (DIMM 2)
Memory block 144-275: Normal (DIMM 3)
Memory block 176-207: Normal (DIMM 4)
... all Normal
(-> hotplugged Normal memory does not allow for more Movable memory)
For virtio-mem, using a simple, single virtio-mem device with a 4 GiB VM
will result in the following layout:
Memory block 0-15: DMA32 (early)
Memory block 32-47: Normal (early)
Memory block 48-143: Movable (virtio-mem, first 12 GiB)
Memory block 144: Normal (virtio-mem, next 128 MiB)
Memory block 145-147: Movable (virtio-mem, next 384 MiB)
Memory block 148: Normal (virtio-mem, next 128 MiB)
Memory block 149-151: Movable (virtio-mem, next 384 MiB)
... Normal/Movable mixture as above
(-> hotplugged Normal memory allows for more Movable memory within
the same device)
Which gives us maximum flexibility when dynamically growing/shrinking a
VM in smaller steps.
V. Doc Update
I'll update the memory-hotplug.rst documentation, once the overhaul [1] is
usptream. Until then, details can be found in patch #2.
VI. Future Work
1) Use memory groups for ppc64 dlpar
2) Being able to specify a portion of (early) kernel memory that will be
excluded from the ratio. Like "128 MiB globally/per node" are excluded.
This might be helpful when starting VMs with extremely small memory
footprint (e.g., 128 MiB) and hotplugging memory later -- not wanting
the first hotplugged units getting onlined to ZONE_MOVABLE. One
alternative would be a trigger to not consider ZONE_DMA memory
in the ratio. We'll have to see if this is really rrequired.
3) Indicate to user space that MOVABLE might be a bad idea -- especially
relevant when memory ballooning without support for balloon compaction
is active.
This patch (of 9):
For implementing a new memory onlining policy, which determines when to
online memory blocks to ZONE_MOVABLE semi-automatically, we need the
number of present early (boot) pages -- present pages excluding hotplugged
pages. Let's track these pages per zone.
Pass a page instead of the zone to adjust_present_page_count(), similar as
adjust_managed_page_count() and derive the zone from the page.
It's worth noting that a memory block to be offlined/onlined is either
completely "early" or "not early". add_memory() and friends can only add
complete memory blocks and we only online/offline complete (individual)
memory blocks.
Link: https://lkml.kernel.org/r/20210806124715.17090-1-david@redhat.com
Link: https://lkml.kernel.org/r/20210806124715.17090-2-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Marek Kedzierski <mkedzier@redhat.com>
Cc: Hui Zhu <teawater@gmail.com>
Cc: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Cc: Wei Yang <richard.weiyang@linux.alibaba.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Len Brown <lenb@kernel.org>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We allocate + initialize everything from scratch. In case enabling the
device fails, we free all memory resourcs.
Link: https://lkml.kernel.org/r/20210712124052.26491-5-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Reviewed-by: Pankaj Gupta <pankaj.gupta@ionos.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.ibm.com>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Anton Blanchard <anton@ozlabs.org>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Baoquan He <bhe@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Jia He <justin.he@arm.com>
Cc: Joe Perches <joe@perches.com>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: Laurent Dufour <ldufour@linux.ibm.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Michel Lespinasse <michel@lespinasse.org>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Nathan Lynch <nathanl@linux.ibm.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Pierre Morel <pmorel@linux.ibm.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Rich Felker <dalias@libc.org>
Cc: Scott Cheloha <cheloha@linux.ibm.com>
Cc: Sergei Trofimovich <slyfox@gentoo.org>
Cc: Thiago Jung Bauermann <bauerman@linux.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Wei Yang <richard.weiyang@linux.alibaba.com>
Cc: Will Deacon <will@kernel.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There is only a single user remaining. We can simply lookup the nid only
used for node offlining purposes when walking our memory blocks. We don't
expect to remove multi-nid ranges; and if we'd ever do, we most probably
don't care about removing multi-nid ranges that actually result in empty
nodes.
If ever required, we can detect the "multi-nid" scenario and simply try
offlining all online nodes.
Link: https://lkml.kernel.org/r/20210712124052.26491-4-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Len Brown <lenb@kernel.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Nathan Lynch <nathanl@linux.ibm.com>
Cc: Laurent Dufour <ldufour@linux.ibm.com>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.ibm.com>
Cc: Scott Cheloha <cheloha@linux.ibm.com>
Cc: Anton Blanchard <anton@ozlabs.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Baoquan He <bhe@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jia He <justin.he@arm.com>
Cc: Joe Perches <joe@perches.com>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Michel Lespinasse <michel@lespinasse.org>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Pankaj Gupta <pankaj.gupta@ionos.com>
Cc: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Pierre Morel <pmorel@linux.ibm.com>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: Rich Felker <dalias@libc.org>
Cc: Sergei Trofimovich <slyfox@gentoo.org>
Cc: Thiago Jung Bauermann <bauerman@linux.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Wei Yang <richard.weiyang@linux.alibaba.com>
Cc: Will Deacon <will@kernel.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Patch series "mm: remove pfn_valid_within() and CONFIG_HOLES_IN_ZONE".
After recent updates to freeing unused parts of the memory map, no
architecture can have holes in the memory map within a pageblock. This
makes pfn_valid_within() check and CONFIG_HOLES_IN_ZONE configuration
option redundant.
The first patch removes them both in a mechanical way and the second patch
simplifies memory_hotplug::test_pages_in_a_zone() that had
pfn_valid_within() surrounded by more logic than simple if.
This patch (of 2):
After recent changes in freeing of the unused parts of the memory map and
rework of pfn_valid() in arm and arm64 there are no architectures that can
have holes in the memory map within a pageblock and so nothing can enable
CONFIG_HOLES_IN_ZONE which guards non trivial implementation of
pfn_valid_within().
With that, pfn_valid_within() is always hardwired to 1 and can be
completely removed.
Remove calls to pfn_valid_within() and CONFIG_HOLES_IN_ZONE.
Link: https://lkml.kernel.org/r/20210713080035.7464-1-rppt@kernel.org
Link: https://lkml.kernel.org/r/20210713080035.7464-2-rppt@kernel.org
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: David Hildenbrand <david@redhat.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There is a statement that is indented one character too deeply,
clean this up.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210902215737.55570-1-colin.king@canonical.com
|
|
syzbot is reporting page fault at vga16fb_fillrect() [1], for
vga16fb_check_var() is failing to detect multiplication overflow.
if (vxres * vyres > maxmem) {
vyres = maxmem / vxres;
if (vyres < yres)
return -ENOMEM;
}
Since no module would accept too huge resolutions where multiplication
overflow happens, let's reject in the common path.
Link: https://syzkaller.appspot.com/bug?extid=04168c8063cfdde1db5e [1]
Reported-by: syzbot <syzbot+04168c8063cfdde1db5e@syzkaller.appspotmail.com>
Debugged-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/185175d6-227a-7b55-433d-b070929b262c@i-love.sakura.ne.jp
|
|
* acpi-pm:
ACPI: PM: s2idle: Run both AMD and Microsoft methods if both are supported
* acpi-docs:
Documentation: ACPI: Align the SSDT overlays file with the code
|
|
* pm-cpufreq:
Revert "cpufreq: intel_pstate: Process HWP Guaranteed change notification"
cpufreq: mediatek-hw: Add support for CPUFREQ HW
cpufreq: Add of_perf_domain_get_sharing_cpumask
dt-bindings: cpufreq: add bindings for MediaTek cpufreq HW
cpufreq: Remove ready() callback
cpufreq: sh: Remove sh_cpufreq_cpu_ready()
cpufreq: acpi: Remove acpi_cpufreq_cpu_ready()
cpufreq: qcom-hw: Set dvfs_possible_from_any_cpu cpufreq driver flag
cpufreq: blocklist more Qualcomm platforms in cpufreq-dt-platdev
cpufreq: qcom-cpufreq-hw: Add dcvs interrupt support
cpufreq: scmi: Use .register_em() to register with energy model
cpufreq: vexpress: Use .register_em() to register with energy model
cpufreq: scpi: Use .register_em() to register with energy model
cpufreq: qcom-cpufreq-hw: Use .register_em() to register with energy model
cpufreq: omap: Use .register_em() to register with energy model
cpufreq: mediatek: Use .register_em() to register with energy model
cpufreq: imx6q: Use .register_em() to register with energy model
cpufreq: dt: Use .register_em() to register with energy model
cpufreq: Add callback to register with energy model
cpufreq: vexpress: Set CPUFREQ_IS_COOLING_DEV flag
|
|
Driver has to swap the endian before send brightness level value
to tcon.
v2: Use __be16 instead of u16 to fix sparse warning.
v3: Send one or two bytes brightness value depend on the precision.
v4: get data length of brightness value more easily.
Reported-by: kernel test robot <lkp@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Cooper Chiou <cooper.chiou@intel.com>
Cc: William Tseng <william.tseng@intel.com>
Signed-off-by: Lee Shawn C <shawn.c.lee@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210908115607.9633-6-shawn.c.lee@intel.com
|
|
So far, DCS backlight driver hardcode (0xFF) for max brightness level.
MIPI DCS spec allow max 0xFFFF for set_display_brightness (51h) command.
And VBT brightness precision bits can support 8 ~ 16 bits.
We should set correct precision bits in VBT that meet panel's request.
Driver can refer to this setting then configure max brightness level
in DCS backlight driver properly.
v2: modify variable name brightness_precision_bits instead of
max_brightness_level.
v3: fix checkpatch warning.
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Cooper Chiou <cooper.chiou@intel.com>
Cc: William Tseng <william.tseng@intel.com>
Signed-off-by: Lee Shawn C <shawn.c.lee@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210908115607.9633-5-shawn.c.lee@intel.com
|
|
VDSC engine can process only 1 pixel per Cd clock. In case
VDSC is used and max slice count == 1, max supported pixel
clock should be 100% of CD clock. Then do min_cdclk and
pixel clock comparison to get proper min cdclk.
v2:
- Check for dsc enable and slice count ==1 then allow to
double confirm min cdclk value.
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Cooper Chiou <cooper.chiou@intel.com>
Cc: William Tseng <william.tseng@intel.com>
Signed-off-by: Lee Shawn C <shawn.c.lee@intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210908115607.9633-4-shawn.c.lee@intel.com
|
Wei Huang
Hans de Goede
Heikki Krogerus
Guenter Roeck
Íñigo Huguet
Joakim Zhang
Tong Zhang
Sukadev Bhattiprolu
Paolo Abeni
Yu-Tung Chang
Juston Li
Dave Airlie
Linus Torvalds
Dan Williams
Aubrey Li
Daniel Lezcano
David Hildenbrand
Mike Rapoport
Colin Ian King
Tetsuo Handa
Rafael J. Wysocki
Lee Shawn C