| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
There is an ASSERT_RTNL in phylink_disconnect_phy which triggers
whenever dpaa2_switch_port_disconnect_mac is called.
To follow the pattern established by dpaa2_eth_disconnect_mac, take the
rtnl_mutex every time we call dpaa2_switch_port_disconnect_mac.
Fixes: 84cba72956fd ("dpaa2-switch: integrate the MAC endpoint support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When disable_irq_nosync for an interrupt is called from within its
interrupt handler, this interrupt is only marked as disabled with the
intention to mask it when it triggers again.
The AIC hardware however automatically masks the interrupt when it is read.
aic_irq_eoi then unmasks it again if it's not disabled *and* not masked.
This results in a state mismatch between the hardware state and the
state kept in irq_data: The hardware interrupt is masked but
IRQD_IRQ_MASKED is not set. Any further calls to unmask_irq will directly
return and the interrupt can never be enabled again.
Fix this by keeping the hardware and irq_data state in sync by unmasking in
aic_irq_eoi if and only if the irq_data state also assumes the interrupt to
be unmasked.
Fixes: 76cde2639411 ("irqchip/apple-aic: Add support for the Apple Interrupt Controller")
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Acked-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210812100942.17206-1-sven@svenpeter.dev
|
|
Configure speed if loopback is used. read_status is not called for
loopback.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
struct phy_device contains a pointer to the PHY driver and nearly
everywhere this pointer is used to access the PHY driver. Only
mdio_bus_phy_may_suspend() is still using to_phy_driver() instead of the
PHY driver pointer. Uniform PHY driver access by eliminating
to_phy_driver() use in mdio_bus_phy_may_suspend().
Only phy_bus_match() and phy_probe() are still using to_phy_driver(),
because PHY driver pointer is not available there.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
phy_read_status and various other PHY functions support PHY specific
overriding of driver functions by using a PHY specific pointer to the
PHY driver. Add support of PHY specific override to phy_loopback too.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This add frame DMA functionality to the Sparx5 platform.
Ethernet frames can be extracted or injected autonomously to or from the
device’s DDR3/DDR3L memory and/or PCIe memory space. Linked list data
structures in memory are used for injecting or extracting Ethernet frames.
The FDMA generates interrupts when frame extraction or injection is done
and when the linked lists need updating.
The FDMA implements two extraction channels, one per switch core port
towards the VCore CPU system and a total of six injection channels.
Extraction channels are mapped one-to-one to the CPU ports, while injection
channels can be individually assigned to any CPU port.
- FDMA channel 0 through 5 corresponds to CPU port 0 injection direction
FDMA_CH_CFG[channel].CH_INJ_PORT is set to 0.
- FDMA channel 0 through 5 corresponds to CPU port 1 injection direction when
FDMA_CH_CFG[channel].CH_INJ_PORT is set to 1.
- FDMA channel 6 corresponds to CPU port 0 extraction direction.
- FDMA channel 7 corresponds to CPU port 1 extraction direction.
The FDMA implements a strict priority scheme among channels. Extraction
channels are prioritized over injection channels and secondarily channels
with higher channel number are prioritized over channels with lower number.
On the other hand, ports are being served on an equal-bandwidth principle
both on injection and extraction directions. The equal-bandwidth principle
will not force an equal bandwidth. Instead, it ensures that the ports
perform at their best considering the operating conditions.
When more than one injection channel is enabled for injection on the same
CPU port, priority determines which channel can inject data. Ownership
is re-arbitrated on frame boundaries.
The FDMA processes linked lists of DMA Control Block Structures (DCBs). The
DCBs have the same basic structure for both injection and extraction. A DCB
must be placed on a 64-bit word-aligned address in memory. Each DCB has a
per-channel configurable amount of associated data blocks in memory, where
the frame data is stored.
The data blocks that are used by extraction channels must be placed on
64-bit word aligned addresses in memory, and their length must be a
multiple of 128 bytes.
A DCB carries the pointer to the next DCB of the linked list, the INFO word
which holds information for the DCB, and a pair of status word and memory
pointer for every data block that it is associated with.
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The device string on these can differ, apparently, including typos. I've
bought 2 of these in 2012 and googling shows many folks out there with
that broken spelling in their dmesg.
Signed-off-by: Ulrich Spörlein <uqs@FreeBSD.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This commit adds support for the Guitar Hero Live PS4 dongles.
These dongles require a "magic" USB control message to be sent
every 8 seconds otherwise the dongle will not report events where
the strumbar is hit while a fret is being held.
Note that the GHL_GUITAR_POKE_INTERVAL is reduced to 8 seconds in order
to support PS3, Wii U, and PS4 GHL dongles.
Also note that the constant for vendor id 0x1430 has been renamed from
Activision to RedOctane as self-declared by the device.
Co-developed-by: Pascal Giard <pascal.giard@etsmtl.ca>
Signed-off-by: Pascal Giard <pascal.giard@etsmtl.ca>
Signed-off-by: Daniel Nguyen <daniel.nguyen.1@ens.etsmtl.ca>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Commit c49c33637802 ("HID: support for initialization of some Thrustmaster
wheels") messed up the Makefile and quirks during the refactoring of this
commit.
Luckily, ./scripts/checkkconfigsymbols.py warns on non-existing configs:
HID_TMINIT
Referencing files: drivers/hid/Makefile, drivers/hid/hid-quirks.c
Following the discussion (see Link), CONFIG_HID_THRUSTMASTER is the
intended config for CONFIG_HID_TMINIT and the file hid-tminit.c was
actually added as hid-thrustmaster.c.
So, clean up Makefile and adapt quirks to that refactoring.
Fixes: c49c33637802 ("HID: support for initialization of some Thrustmaster wheels")
Link: https://lore.kernel.org/linux-input/CAKXUXMx6dByO03f3dX0X5zjvQp0j2AhJBg0vQFDmhZUhtKxRxw@mail.gmail.com/
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
A quirk was recently added for Elan devices that has same device match
as an entry earlier in the list. The i2c_hid_lookup_quirk function will
always return the last match in the list, so the new entry shadows the
old entry. The quirk in the previous entry, I2C_HID_QUIRK_BOGUS_IRQ,
silenced a flood of messages which have reappeared in the 5.13 kernel.
This change moves the two quirk flags into the same entry.
Fixes: ca66a6770bd9 (HID: i2c-hid: Skip ELAN power-on command after reset)
Signed-off-by: Jim Broadus <jbroadus@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Prevent the ASUS Claymore keyboard from sending a suspend event
when the device sleeps itself. The suspend event causes a system
suspend if uncaught.
Signed off by: Luke D Jones <luke@ljones.dev>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Add dynamic debug for debugging sensors states during
initialization, stop, suspend and resume.
Reviewed-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Add support for power management routines.
Reviewed-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Earlier platforms don’t have sensor status checking mechanism.
Sensors are always enabled without checking sensor status.
Hence invoke hid probe only after the sensor is enabled by
checking sensor status.
Reviewed-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Sometimes sensor enable/disable may take time, without checking the
actual status bits from MP2 FW can lead the amd-sfh to misbehave.
Hence add a status check of enable/disable command
by waiting on the command response before sending the next
command to FW.
Reviewed-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Existing amd-sfh driver is programming the MP2 firmware period field in
units of jiffies, but the MP2 firmware expects in milliseconds unit.
Changing it to milliseconds.
Fixes: 4b2c53d93a4b ("SFH:Transport Driver to add support of AMD Sensor Fusion Hub (SFH)")
Reviewed-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Add driver for Intel Keem Bay SoC PCIe controller. This controller
is based on DesignWare PCIe core.
In Root Complex mode, only internal reference clock is possible for
Keem Bay A0. For Keem Bay B0, external reference clock can be used
and will be the default configuration. Currently, keembay_pcie_of_data
structure has one member. It will be expanded later to handle this
difference.
Endpoint mode link initialization is handled by the boot firmware.
Link: https://lore.kernel.org/r/20210805211010.29484-3-srikanth.thokala@intel.com
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Signed-off-by: Srikanth Thokala <srikanth.thokala@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
In commit 6df6ba974a55 ("PCI: aardvark: Remove PCIe outbound window
configuration") was removed aardvark PCIe outbound window configuration and
commit description said that was recommended solution by HW designers.
But that commit completely removed support for configuring PCIe IO
resources without removing PCIe IO 'ranges' from DTS files. After that
commit PCIe IO space started to be treated as PCIe MEM space and accessing
it just caused kernel crash.
Moreover implementation of PCIe outbound windows prior that commit was
incorrect. It completely ignored offset between CPU address and PCIe bus
address and expected that in DTS is CPU address always same as PCIe bus
address without doing any checks. Also it completely ignored size of every
PCIe resource specified in 'ranges' DTS property and expected that every
PCIe resource has size 128 MB (also for PCIe IO range). Again without any
check. Apparently none of PCIe resource has in DTS specified size of 128
MB. So it was completely broken and thanks to how aardvark mask works,
configuration was completely ignored.
This patch reverts back support for PCIe outbound window configuration but
implementation is a new without issues mentioned above. PCIe outbound
window is required when DTS specify in 'ranges' property non-zero offset
between CPU and PCIe address space. To address recommendation by HW
designers as specified in commit description of 6df6ba974a55, set default
outbound parameters as PCIe MEM access without translation and therefore
for this PCIe 'ranges' it is not needed to configure PCIe outbound window.
For PCIe IO space is needed to configure aardvark PCIe outbound window.
This patch fixes kernel crash when trying to access PCIe IO space.
Link: https://lore.kernel.org/r/20210624215546.4015-2-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org # 6df6ba974a55 ("PCI: aardvark: Remove PCIe outbound window configuration")
|
|
Add the missing unlock before return from function arm_smmu_device_group()
in the error handling case.
Fixes: b1a1347912a7 ("iommu/arm-smmu: Fix race condition during iommu_group creation")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210820074949.1946576-1-yangyingliang@huawei.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
For devices that only support the BATTERY_VOLTAGE (0x1001) feature, UPower
requires the additional information provided by this patch, to set them up.
Signed-off-by: Hamza Mahfooz <someguy@effective-light.com>
Reviewed-by: Filipe Laíns <lains@riseup.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
thrustmaster_interrupts() does not free memory for send_buf when
usb_interrupt_msg() fails. This is fixed by the given patch.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
thrustmaster_remove() does not release memory for
tm_wheel->change_request. This is fixed by the patch.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
When thrustmaster_probe() handles errors of usb_submit_urb() it does not
free allocated resources and fails. The patch fixes that.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Use usb_get_dev() to increment the reference count of the usb device
structure in order to avoid releasing the structure while it is still in
use. And use usb_put_dev() to decrement the reference count and thus,
when it will be equal to 0 the structure will be released.
Signed-off-by: Salah Triki <salah.triki@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This function logs a warning if the workqueue gets too big.
In order to save a few cycles, use 'atomic_inc_return()' instead of an
'atomic_inc()/atomic_read()' sequence.
This axes a line of code and saves a 'atomic_read()' call.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
drivers/spi/spi-stm32.c:915:23-25: WARNING !A || A && B is equivalent to !A || B
Condition !A || A && B is equivalent to !A || B.
Generated by: scripts/coccinelle/misc/excluded_middle.cocci
Fixes: 7ceb0b8a3ced ("spi: stm32: finalize message either on dma callback or EOT")
CC: Alain Volmat <alain.volmat@foss.st.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: kernel test robot <lkp@intel.com>
Reviewed-by: Alain Volmat <alain.volmat@foss.st.com>
Link: https://lore.kernel.org/r/20210713191004.GA14729@5eb5c2cbef84
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Saeed Mahameed says:
====================
mlx5-updates-2021-08-19
This series introduces the support for two new mlx5 features:
1) Sample offload for tunneled traffic
2) devlink rate objects support
1) From Chris Mi: Sample offload for tunneled traffic
=====================================================
Background and solution
-----------------------
Currently the sample offload actions send the encapsulated packet
to software. This series de-capsulates the packet before performing
the sampling and set the tunnel properties on the skb metadata
fields to make the behavior consistent with OVS sFlow.
If de-capsulating first, we can't use the same match like before in
default table. So instantiate a post action instance to continue
processing the action list. If HW can preserve reg_c, also use the
post action instance.
Post action infrastructure
--------------------------
Some tc actions are modeled in hardware using multiple tables
causing a tc action list split. For example, CT action is modeled
by jumping to a ct table which is controlled by nf flow table.
sFlow jumps in hardware to a sample table, which continues to a
"default table" where it should continue processing the action list.
Multi table actions are modeled in hardware using a unique fte_id.
The fte_id is set before jumping to a table. Split actions continue
to a post-action table where the matched fte_id value continues the
execution the tc action list.
This series also introduces post action infrastructure. Both ct and
sample use it.
Sample for tunnel in TC SW
--------------------------
tc filter add dev vxlan1 protocol ip parent ffff: prio 3 \
flower src_mac 24:25:d0:e1:00:00 dst_mac 02:25:d0:13:01:02 \
enc_src_ip 192.168.1.14 enc_dst_ip 192.168.1.13 \
enc_dst_port 4789 enc_key_id 4 \
action sample rate 1 group 6 \
action tunnel_key unset \
action mirred egress redirect dev enp4s0f0_1
MLX5 sample HW offload
----------------------
For the following typical flow table:
+-------------------------------+
+ original flow table +
+-------------------------------+
+ original match +
+-------------------------------+
+ sample action + other actions +
+-------------------------------+
We translate the tc filter with sample action to the following HW model:
+---------------------+
+ original flow table +
+---------------------+
+ original match +
+---------------------+
| set fte_id (if reg_c preserve cap)
| do decap
v
+------------------------------------------------+
+ Flow Sampler Object +
+------------------------------------------------+
+ sample ratio +
+------------------------------------------------+
+ sample table id | default table id +
+------------------------------------------------+
| |
v v
+-----------------------------+ +-------------------+
+ sample table + + default table +
+-----------------------------+ +-------------------+
+ forward to management vport + |
+-----------------------------+ |
+-------+------+
| |reg_c preserve cap
| |or decap action
v v
+-----------------+ +-------------+
+ per vport table + + post action +
+-----------------+ +-------------+
+ original match +
+-----------------+
+ other actions +
+-----------------+
2) From Dmytro Linkin: devlink rate object support for mlx5_core driver
=======================================================================
HIGH-LEVEL OVERVIEW
Devlink leaf rate objects created per vport (VF/SF, and PF on BlueField)
in switchdev mode on devlink port registration.
Implement devlink ops callbacks to create/destroy rate groups, set TX
rate values of the vport/group, assign vport to the group.
Driver accepts TX rate values as fraction of 1Mbps.
Refactor existing eswitch QoS infrastructure to be accessible by legacy
NDO rate API and new devlink rate API. NDO rate API is not
removed/disabled in switchdev mode to not break existing users. Rate
values configured with NDO rate API are not visible for devlink
infrastructure, therefore APIs should not be used simultaneously.
IMPLEMENTATION DETAILS
Driver provide two level rate hierarchy to manage bandwidth - group
level and vport level. Initially each vport added to internal unlimited
group created by default. Each rate element (vport or group) receive
bandwidth relative to its parent element (for groups the parent is a
physical link itself) in a Round Robin manner, where element get
bandwidth value according to its weight. Example:
Created four rate groups with tx_share limits:
$ devlink port function rate add \
pci/0000:06:00.0/group_1 tx_share 30gbit
$ devlink port function rate add \
pci/0000:06:00.0/group_2 tx_share 20gbit
$ devlink port function rate add \
pci/0000:06:00.0/group_3 tx_share 20gbit
$ devlink port function rate add \
pci/0000:06:00.0/group_4 tx_share 10gbit
Weights created in HW for each group are relative to the bigest tx_share
value, which is 30gbit:
<group_1> 1.0
<group_2> 0.67
<group_3> 0.67
<group_4> 0.33
Assuming link speed is 50 Gbit/sec and each group can sustain such
amount of traffic, maximum bandwidth is 50 / (1.0 + 0.67 + 0.67 + 0.33)
= ~18.75 Gbit/sec. Normilized bandwidth values for groups:
<group_1> 18.75 * 1.0 = 18.75 Gbit/sec
<group_2> 18.75 * 0.67 = 12.5 Gbit/sec
<group_3> 18.75 * 0.67 = 12.5 Gbit/sec
<group_4> 18.75 * 0.33 = 6.25 Gbit/sec
If in example above group_1 doesn't produce any traffic, then maximum
bandwidth becomes 50 / (0.67 + 0.67 + 0.33) = ~30.0 Gbit/sec. Normalized
values:
<group_2> 30.0 * 0.67 = 20.0 Gbit/sec
<group_3> 30.0 * 0.67 = 20.0 Gbit/sec
<group_4> 30.0 * 0.33 = 10.0 Gbit/sec
Same normalization applied to each vport in the group.
Normalized values are internal, therefore driver provides QoS
tracepoints for next events:
* vport rate element creation/deletion:
* vport rate element configuration;
* group rate element creation/deletion;
* group rate element configuration.
PATCHES OVERVIEW
1 - Moving and isolation of eswitch QoS logic in separate file;
2 - Implement devlink leaf rate object support for vports;
3 - Implement rate groups creation/deletion;
4 - Implement TX rate management for the groups;
5 - Implement parent set for vports;
6 - Eswitch QoS tracepoints.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Luiz Augusto von Dentz says:
====================
bluetooth-next pull request for net-next:
- Add support for Foxconn Mediatek Chip
- Add support for LG LGSBWAC92/TWCM-K505D
- hci_h5 flow control fixes and suspend support
- Switch to use lock_sock for SCO and RFCOMM
- Various fixes for extended advertising
- Reword Intel's setup on btusb unifying the supported generations
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the new drm_connector_oob_hotplug_event() functions to let drm/kms
drivers know about DisplayPort over Type-C hotplug events.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://lore.kernel.org/r/20210817215201.795062-9-hdegoede@redhat.com
|
|
Make dp_altmode_notify() handle the dp->data.conf == 0 case too,
rather then having separate code-paths for this in various places
which call it.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://lore.kernel.org/r/20210817215201.795062-8-hdegoede@redhat.com
|
|
Add a new drm_connector_oob_hotplug_event() function and
oob_hotplug_event drm_connector_funcs member.
On some hardware a hotplug event notification may come from outside the
display driver / device. An example of this is some USB Type-C setups
where the hardware muxes the DisplayPort data and aux-lines but does
not pass the altmode HPD status bit to the GPU's DP HPD pin.
In cases like this the new drm_connector_oob_hotplug_event() function can
be used to report these out-of-band events.
Changes in v2:
- Make drm_connector_oob_hotplug_event() take a fwnode as argument and
have it call drm_connector_find_by_fwnode() internally. This allows
making drm_connector_find_by_fwnode() a drm-internal function and
avoids code outside the drm subsystem potentially holding on the
a drm_connector reference for a longer period.
Changes in v3:
- Drop the data argument to the drm_connector_oob_hotplug_event
function since it is not used atm. This can be re-added later when
a use for it actually arises.
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://lore.kernel.org/r/20210817215201.795062-5-hdegoede@redhat.com
|
|
Add a function to find a connector based on a fwnode.
This will be used by the new drm_connector_oob_hotplug_event()
function which is added by the next patch in this patch-set.
Changes in v2:
- Complete rewrite to use a global connector list in drm_connector.c
rather then using a class-dev-iter in drm_sysfs.c
Changes in v3:
- Add forward declaration for struct fwnode_handle to drm_crtc_internal.h
(fixes warning reported by kernel test robot <lkp@intel.com>)
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://lore.kernel.org/r/20210817215201.795062-4-hdegoede@redhat.com
|
|
Add a fwnode pointer to struct drm_connector and register an acpi_bus_type
for the connectors with the ACPI subsystem (when CONFIG_ACPI is enabled).
The adding of the fwnode pointer allows drivers to associate a fwnode
that represents a connector with that connector.
When the new fwnode pointer points to an ACPI-companion, then the new
acpi_bus_type will cause the ACPI subsys to bind the device instantiated
for the connector with the fwnode by calling acpi_bind_one(). This will
result in a firmware_node symlink under /sys/class/card#-<connecter-name>/
which helps to verify that the fwnode-s and connectors are properly
matched.
Changes in v2:
- Make drm_connector_cleanup() call fwnode_handle_put() on
connector->fwnode and document this
Co-developed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://lore.kernel.org/r/20210817215201.795062-3-hdegoede@redhat.com
|
|
Give connector sysfs devices there own device_type, this allows us to
check if a device passed to functions dealing with generic devices is
a drm_connector or not.
A check like this is necessary in the drm_connector_acpi_bus_match()
function added in the next patch in this series.
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://lore.kernel.org/r/20210817215201.795062-2-hdegoede@redhat.com
|
|
Add initial support for platform_profile where the support is
based on availability of ASUS_THROTTLE_THERMAL_POLICY.
Because throttle_thermal_policy is used by platform_profile and is
writeable separately to platform_profile any userspace changes to
throttle_thermal_policy need to notify platform_profile.
In future throttle_thermal_policy sysfs should be removed so that
only one method controls the laptop power profile.
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Link: https://lore.kernel.org/r/20210818190731.19170-2-luke@ljones.dev
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Use led_classdev_notify_brightness_hw_changed() instead of F16 key.
Signed-off-by: Matan Ziv-Av <matan@svgalib.org>
Link: https://lore.kernel.org/r/2196990f167efe6a42d51fb85f4db4cdf4d9e80e.1629291912.git.matan@svgalib.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Send F21 which is the standard for this key, instead of F13.
Signed-off-by: Matan Ziv-Av <matan@svgalib.org>
Link: https://lore.kernel.org/r/b847895c1f170e2e59df5757a4d603d28149f648.1629291912.git.matan@svgalib.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Add support for the difference between various models:
- Use dmi to detect laptop model.
- 2019 and newer models use _wmbb method to set battery charge limit.
Signed-off-by: Matan Ziv-Av <matan@svgalib.org>
Link: https://lore.kernel.org/r/bd6922a412e50c2dcfb7ce24fc8687f577181d65.1629291912.git.matan@svgalib.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Dynamic BIOS SAR driver exposing dynamic SAR information from BIOS
The Dynamic SAR (Specific Absorption Rate) driver uses ACPI DSM
(Device Specific Method) to communicate with BIOS and retrieve
dynamic SAR information and change notifications. The driver uses
sysfs to expose this data to userspace via read and notify.
Sysfs interface is documented in detail under:
Documentation/ABI/testing/sysfs-driver-intc_sar
Signed-off-by: Shravan S <s.shravan@intel.com>
Link: https://lore.kernel.org/r/20210723211452.27995-2-s.shravan@intel.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Some devices may expose non-functioning entries that are reserved for
future use. These entries have zero size. Ignore them during probe.
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Link: https://lore.kernel.org/r/20210817224018.1013192-5-david.e.box@linux.intel.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
This patch fixes the bug 212671.
Althrough the Fn lock (Fn + Esc) works on Legion 5 (R7000P), its LED
light does not change with the state. This modification sets the Fn lock
state to its current value on receiving the wmi event
8FC0DE0C-B4E4-43FD-B0F3-8871711C1294 to update the LED state.
Signed-off-by: Meng Dong <whenov@gmail.com>
Link: https://lore.kernel.org/r/20210817171203.12855-1-whenov@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Reported as working here:
https://github.com/t-8ch/linux-gigabyte-wmi-driver/issues/1#issuecomment-901207693
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20210818164435.99821-1-linux@weissschuh.net
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The deprecated i2c probe functionality doesn't work with OF
compatible strings, as it only checks for the i2c device id. Switch
to the new way of probing and grab the match data to select the
chip type.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
|
|
Much of the fwnode processing in the PCA955x driver is now in the
LEDs core driver, so pass the fwnode in the init data when
registering the LED device. In order to preserve the existing naming
scheme, check for an empty name and set it to the LED number.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
|
|
In order to retain the LED state after a system reboot, check the
documented default-state device tree property during initialization.
Modify the behavior of the probe according to the property.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
|
|
Add a function to fetch the state of the hardware LED.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
|
|
Format the code. Add some variables to help shorten lines.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
|
|
Read the retain-state-shutdown device tree property to set the
existing LED_RETAIN_AT_SHUTDOWN flag. Then check the flag when
unregistering, and if set, don't set the brightness to OFF. This
is useful for systems that want to keep the HW state of the LED
across reboots.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
|
|
This should give a more complete view of the various bits of internal
resource manager state, for device local-memory.
v2(Thomas):
- Move the region printing into a nice helper
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210819093419.295636-2-matthew.auld@intel.com
|
|
Implement the debug hook for the buddy resource manager. For this we
want to print out the status of the memory manager, including how much
memory is still allocatable, what page sizes we have etc. This will be
triggered when TTM is unable to fulfil an allocation request for device
local-memory.
v2(Thomas):
- s/MB/MiB
- s/KB/KiB
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210819093419.295636-1-matthew.auld@intel.com
|
Vladimir Oltean
Sven Peter
Gerhard Engleder
Steen Hegelund
Ulrich Spörlein
Daniel Nguyen
Lukas Bulwahn
Jim Broadus
Luke D. Jones
Basavaraj Natikar
Srikanth Thokala
Pali Rohár
Yang Yingliang
Hamza Mahfooz
Evgeny Novikov
Salah Triki
Christophe JAILLET
kernel test robot
David S. Miller
Hans de Goede
Matan Ziv-Av
Shravan S
David E. Box
Meng Dong
Thomas Weißschuh
Eddie James
Matthew Auld