| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
There's an undocumented dependency between LCD layer enable bits [2-5]
and the AXI pipelined read enable bit [28] in the LCD_CONTROL register.
The proper order of operation is:
1) Clear AXI pipelined read enable bit
2) Set LCD layers
3) Set AXI pipelined read enable bit
With this update, LCD can start DMA when TVDDCV is reduced down to 700mV.
Fixes: 7f7b96a8a0a1 ("drm/kmb: Add support for KeemBay Display")
Signed-off-by: Edmund Dea <edmund.j.dea@intel.com>
Signed-off-by: Anitha Chrisanthus <anitha.chrisanthus@intel.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210728003126.1425028-1-anitha.chrisanthus@intel.com
|
|
Fix the following fallthrough warning (on ARM):
drivers/scsi/arm/fas216.c:1379:2: warning: unannotated fall-through between switch labels [-Wimplicit-fallthrough]
default:
^
drivers/scsi/arm/fas216.c:1379:2: note: insert 'break;' to avoid fall-through
default:
^
break;
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/lkml/202107260355.bF00i5bi-lkp@intel.com/
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
|
|
Fix the following fallthrough warning (on ARM):
drivers/scsi/arm/acornscsi.c:2651:2: warning: unannotated fall-through between switch labels [-Wimplicit-fallthrough]
case res_success:
^
drivers/scsi/arm/acornscsi.c:2651:2: note: insert '__attribute__((fallthrough));' to silence this warning
case res_success:
^
__attribute__((fallthrough));
drivers/scsi/arm/acornscsi.c:2651:2: note: insert 'break;' to avoid fall-through
case res_success:
^
break;
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/lkml/202107260355.bF00i5bi-lkp@intel.com/
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
|
|
Gpiolib core code has been updated to support setting friendly names
through properly 'gpio-line-names'. Instead of redefine behaviour here
to skip the core to be executed, just properly assign the desired offset
per bank to get in the core the expected behaviour.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
This driver uses multiple gpiochip banks per device. To support
'gpio-line-names' along the banks 'offset' for each bank must be
set explicitly.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
The default gpiolib-of implementation does not work with the multiple
gpiochip banks per device structure used for example by the gpio-mt7621
and gpio-brcmstb drivers. To fix these kind of situations driver code
is forced to fill the names to avoid the gpiolib code to set names
repeated along the banks. Instead of continue with that antipattern
fix the gpiolib core function to get expected behaviour for every
single situation adding a field 'offset' in the gpiochip structure.
Doing in this way, we can assume this offset will be zero for normal
driver code where only one gpiochip bank per device is used but
can be set explicitly in those drivers that really need more than
one gpiochip.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Replace all remaining handling of GRAPHICS_VER {==,>=} 10 with
{==,>=} 11. With the removal of CNL, there is no platform with graphics
version equals 10.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210728220326.1578242-5-lucas.demarchi@intel.com
|
|
With the removal of CNL, let's consider ICL as the first platform using
that index.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210728220326.1578242-4-lucas.demarchi@intel.com
|
|
CNL is the only platform with GRAPHICS_VER == 10. With its removal we
don't need to handle that version anymore.
Also we can now reduce the max number of slices: the call to
intel_sseu_set_info() with the highest number of slices comes from SKL
and BDW with 3 slices. Recent platforms actually increase the
number of subslices so the number of slices remain 1.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210728220326.1578242-3-lucas.demarchi@intel.com
|
|
Only one reference to CNL that is not needed, but code is the same for
GEN9_BC, so leave the code around and just remove the special
case for CNL.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210728220326.1578242-2-lucas.demarchi@intel.com
|
|
Source needs to write DPCD 103-106 after receiving a PHY request to change
swing/pre-emphasis after reading DPCD 206-207. This is especially needed if
there is a retimer between source and sink and the retimer implements AUX_CH
interception scheme to manage DP PHY settings (e.g. adjusting Swing/Pre-emphasis
equalization level) for DP output channel. If the source doesn't write to
DPCD 103-106, the retimer may not output the requested swing/pre-emphasis and
eventually we fail compliance.
v2: Rebase and use crtc->lane_count (Imre)
Signed-off-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210226081554.984307-1-khaled.almahallawy@intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
|
|
In verify_mpllb_state() encoder is retrieved from best_encoder
of connector_state. As there will be only one connector_state
for bigjoiner and checking encoder may not be needed for
bigjoiner-slave. This code path related to mpll is done on dg2
and need this fix to avoid null pointer dereference issue.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723174239.1551352-30-matthew.d.roper@intel.com
|
|
The PSR enable/disable sequences now require that we program an extra
register in the PHY to adjust the lane disable power setting.
Bspec: 49274
Bspec: 53885
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723174239.1551352-29-matthew.d.roper@intel.com
|
|
Initialization of the PHY is handled by the hardware/firmware, but the
driver should wait up to 25ms for the PHY to report that its calibration
has completed.
Bspec: 49189
Bspec: 50107
Cc: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Matt Atwood <matthew.s.atwood@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723174239.1551352-28-matthew.d.roper@intel.com
|
|
DG2 has some changes to the expected modesetting sequences when compared
to gen12. Adjust our driver logic accordingly. Although the DP
sequence is pretty similar to TGL's, there are some steps that change,
so let's split the handling for that out into a separate function.
v2:
- Switch wait_for_us() -> _wait_for() so that we can parameterize the
timeout rather than duplicating the macro call. (Jani)
Bspec: 54128
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723174239.1551352-27-matthew.d.roper@intel.com
|
|
Vswing programming for SNPS PHYs is just a single step -- look up the
value that corresponds to the voltage level from a table and program it
into the SNPS_PHY_TX_EQ register.
Bspec: 53920
Cc: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Matt Atwood <matthew.s.atwood@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723174239.1551352-26-matthew.d.roper@intel.com
|
|
At the moment we don't have a proper algorithm that can be used to
calculate PHY settings for arbitrary HDMI link rates. The PHY tables
here should support the regular modes of real-world HDMI monitors.
Bspec: 54032
Cc: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Matt Atwood <matthew.s.atwood@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723174239.1551352-25-matthew.d.roper@intel.com
|
|
DG2's SNPS PHYs incorporate a dedicated port PLL called MPLLB which
takes the place of the shared DPLLs we've used on past platforms. Let's
add the MPLLB programming sequences; they'll be plugged into the rest of
the code in future patches.
Bspec: 54032
Bspec: 53881
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Nidhi Gupta <nidhi1.gupta@intel.com>
Reviewed-by: Matt Atwood <matthew.s.atwood@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723174239.1551352-24-matthew.d.roper@intel.com
|
|
Switch to use module_parport_driver() to reduce boilerplate code.
Acked-by: Rodolfo Giometti <giometti@enneenne.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210607153729.58623-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
strcpy() performs no bounds checking on the destination buffer. This
could result in linear overflows beyond the end of the buffer, leading
to all kinds of misbehaviors. The safe replacement is strscpy().
Signed-off-by: Len Baker <len.baker@gmx.com>
Link: https://lore.kernel.org/r/20210718131217.3806-1-len.baker@gmx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
remove some unused static variables. One of them
is used to toggle on the BT coexistence mechanism,
but it is always enabled and it's not conditioned
to the value of the related parameter.
Remove unused field of the registry_priv struct as
well, they were intended for hosting the parameters
this patch rids.
Signed-off-by: Fabio Aiuto <fabioaiuto83@gmail.com>
Link: https://lore.kernel.org/r/20210729125417.4380-1-fabioaiuto83@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This use-after-free happens when a fw_priv object has been freed but
hasn't been removed from the pending list (pending_fw_head). The next
time fw_load_sysfs_fallback tries to insert into the list, it ends up
accessing the pending_list member of the previously freed fw_priv.
The root cause here is that all code paths that abort the fw load
don't delete it from the pending list. For example:
_request_firmware()
-> fw_abort_batch_reqs()
-> fw_state_aborted()
To fix this, delete the fw_priv from the list in __fw_set_state() if
the new state is DONE or ABORTED. This way, all aborts will remove
the fw_priv from the list. Accordingly, remove calls to list_del_init
that were being made before calling fw_state_(aborted|done).
Also, in fw_load_sysfs_fallback, don't add the fw_priv to the pending
list if it is already aborted. Instead, just jump out and return early.
Fixes: bcfbd3523f3c ("firmware: fix a double abort case with fw_load_sysfs_fallback")
Cc: stable <stable@vger.kernel.org>
Reported-by: syzbot+de271708674e2093097b@syzkaller.appspotmail.com
Tested-by: syzbot+de271708674e2093097b@syzkaller.appspotmail.com
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Acked-by: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Anirudh Rayabharam <mail@anirudhrb.com>
Link: https://lore.kernel.org/r/20210728085107.4141-3-mail@anirudhrb.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The only motivation for using -EAGAIN in commit 0542ad88fbdd81bb
("firmware loader: Fix _request_firmware_load() return val for fw load
abort") was to distinguish the error from -ENOMEM, and so there is no
real reason in keeping it. -EAGAIN is typically used to tell the
userspace to try something again and in this case re-using the sysfs
loading interface cannot be retried when a timeout happens, so the
return value is also bogus.
-ETIMEDOUT is received when the wait times out and returning that
is much more telling of what the reason for the failure was. So, just
propagate that instead of returning -EAGAIN.
Suggested-by: Luis Chamberlain <mcgrof@kernel.org>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Acked-by: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Anirudh Rayabharam <mail@anirudhrb.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210728085107.4141-2-mail@anirudhrb.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
pci_irq_vector() may be used to retrieve IRQ vector for a PCI device.
Use it instead of direct access.
Acked-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210721150216.64823-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
IRQ_NONE definition is solely for IRQ handlers and not for generic
probe code. Replace it with plain integer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210721150216.64823-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Buffers and structures passed to MEI bus and client API can be made
const for safer code and clear indication that it is not modified.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210729102803.46289-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix uart corruption issue when rx power off.
Add spin lock in mtk8250_dma_rx_complete function in APDMA mode.
when uart is used as a communication port with external device(GPS).
when external device(GPS) power off, the power of rx pin is also from
1.8v to 0v. Even if there is not any data in rx. But uart rx pin can
capture the data "0".
If uart don't receive any data in specified cycle, uart will generates
BI(Break interrupt) interrupt.
If external device(GPS) power off, we found that BI interrupt appeared
continuously and very frequently.
When uart interrupt type is BI, uart IRQ handler(8250 framwork
API:serial8250_handle_irq) will push data to tty buffer.
mtk8250_dma_rx_complete is a task of mtk_uart_apdma_rx_handler.
mtk8250_dma_rx_complete priority is lower than uart irq
handler(serial8250_handle_irq).
if we are in process of mtk8250_dma_rx_complete, uart appear BI
interrupt:1)serial8250_handle_irq will priority execution.2)it may cause
write tty buffer conflict in mtk8250_dma_rx_complete.
So the spin lock protect the rx receive data process is not break.
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210729084640.17613-2-zhiyong.tao@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Patch e60c2991f18b make the lpuart32_get_mctrl always return 0, actually
this will break the functions of device which use flow control such as
Bluetooth.
For lpuart32 plaform, the hardware can handle the CTS automatically.
So we should set TIOCM_CTS active. Also need to set CAR and DSR active.
Patch has been tested on lpuart32 platforms such as imx8qm and imx8ulp.
Fixes: e60c2991f18b ("serial: fsl_lpuart: remove RTSCTS handling from get_mctrl()")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20210729083109.31541-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For years we've been carrying legacy omap-serial in addition to
8250_omap driver and 8250_omap should be used instead.
Let's finally start planning on removing omap-serial by first not
building it if 8250_omap is selected to save some memory.
The defconfigs have switched over to using 8250_omap, and we have
a fixup in place for the the serial console since commit 00648d0282dc
("tty: serial: 8250: omap: add ttySx console if the user didn't").
So people updating their systems without omap-serial will see
boot time warnings on what is going on.
Cc: Andy Shevchenko <andriy.shevchenko@intel.com>
Cc: Dario Binacchi <dariobin@libero.it>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210727103149.51175-2-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We want to remove the use of pm_runtime_irq_safe() from serial drivers
to allow making PM runtime handling generic. Let's simplify things by
disabling PM runtime autoidle for omap-serial as this driver has been
deprecated for years because of the 8250_omap driver.
There are still some omap-serial users that seem to hang on to it for
some unknown rs485 reasons it seems. But presumably those folks do not
need PM runtime autoidle with omap-serial, and hopefully can just move
to using 8250_omap driver instead.
For 8250_omap driver, we will eventually move to use generic serial
layer PM based on patches done by Andy Shevchenko to remove
pm_runtime_irq_safe() usage.
Cc: Andy Shevchenko <andriy.shevchenko@intel.com>
Cc: Dario Binacchi <dariobin@libero.it>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210727103149.51175-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The struct pxa25x_ep_ops is only assigned to the ops field in the
usb_ep struct, which is a pointer to const struct usb_ep_ops.
Make it const to allow the compiler to put it in read-only memory.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20210728092052.4178-1-rikard.falkeborn@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add a new compatible for SDM660's DWC3.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210728221921.52068-1-konrad.dybcio@somainline.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Removing the qede module version which is not needed and not allowed
with inbox drivers.
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Removing the qed module version which is not needed and not allowed
with inbox drivers.
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Surprisingly, this configuration:
ip link add br0 type bridge vlan_filtering 1
ip link set swp2 master br0
bridge vlan del dev swp2 vid 1
still has the sja1105 switch sending untagged packets to the CPU (and
failing to decode them, since dsa_find_designated_bridge_port_by_vid
searches by VID 1 and rightfully finds no bridge VLAN 1 on a port).
Dumping the switch configuration, the VLANs are managed properly:
- the pvid of swp2 is 1 in the MAC Configuration Table, but
- only the CPU port is in the port membership of VLANID 1 in the VLAN
Lookup Table
When the ingress packets are tagged with VID 1, they are properly
dropped. But when they are untagged, they are able to reach the CPU
port. Also, when the pvid in the MAC Configuration Table is changed to
e.g. 55 (an unused VLAN), the untagged packets are also dropped.
So it looks like:
- the switch bypasses ingress VLAN membership checks for untagged traffic
- the reason why the untagged traffic is dropped when I make the pvid 55
is due to the lack of valid destination ports in VLAN 55, rather than
an ingress membership violation
- the ingress VLAN membership cheks are only done for VLAN-tagged traffic
Interesting. It looks like there is an explicit bit to drop untagged
traffic, so we should probably be using that to preserve user expectations.
Note that only VLAN-aware ports should drop untagged packets due to no
pvid - when VLAN-unaware, the software bridge doesn't do this even if
there is no pvid on any bridge port and on the bridge itself. So the new
sja1105_drop_untagged() function cannot simply be called with "false"
from sja1105_bridge_vlan_add() and with "true" from sja1105_bridge_vlan_del.
Instead, we need to also consider the VLAN awareness state. That means
we need to hook the "drop untagged" setting in all the same places where
the "commit pvid" logic is, and it needs to factor in all the state when
flipping the "drop untagged" bit: is our current pvid in the VLAN Lookup
Table, and is the current port in that VLAN's port membership list?
VLAN-unaware ports will never drop untagged frames because these checks
always succeed by construction, and the tag_8021q VLANs cannot be changed
by the user.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that we no longer have the ultra-central sja1105_build_vlan_table(),
we need to be more careful about checking all corner cases manually.
For example, when a port leaves a VLAN-aware bridge, it becomes
standalone so its pvid should become a tag_8021q RX VLAN again. However,
sja1105_commit_pvid() only gets called from sja1105_bridge_vlan_add()
and from sja1105_vlan_filtering(), and no VLAN awareness change takes
place (VLAN filtering is a global setting for sja1105, so the switch
remains VLAN-aware overall).
This means that we need to put another sja1105_commit_pvid() call in
sja1105_bridge_member().
Fixes: 6dfd23d35e75 ("net: dsa: sja1105: delete vlan delta save/restore logic")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add an empty drivers/net/mctp/, for future interface drivers.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The chip supports high transfer rates, but with the small default buffers
(64 bytes read), some entire blocks are regularly lost. This typically
happens at 1.5 Mbps (which is the default speed on Rockchip devices) when
used as a console to access U-Boot where the output of the "help" command
misses many lines and where "printenv" mangles the environment.
The FTDI driver doesn't suffer at all from this. One difference is that
it uses 512 bytes rx buffers and 256 bytes tx buffers. Adopting these
values completely resolved the issue, even the output of "dmesg" is
reliable. I preferred to leave the Tx value unchanged as it is not
involved in this issue, while a change could increase the risk of
triggering the same issue with other devices having too small buffers.
I verified that it backports well (and works) at least to 5.4. It's of
low importance enough to be dropped where it doesn't trivially apply
anymore.
Cc: stable@vger.kernel.org
Signed-off-by: Willy Tarreau <w@1wt.eu>
Link: https://lore.kernel.org/r/20210724152739.18726-1-w@1wt.eu
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Remove the btusb_table entry for 413c:8197 so the device is handled
by the later Dell vendor entry, which specifies patchram loading.
T: Bus=01 Lev=02 Prnt=02 Port=03 Cnt=02 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=413c ProdID=8197 Rev= 1.12
S: Manufacturer=Dell Computer Corp
S: Product=DW380 Bluetooth Module
S: SerialNumber=74E54354F609
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=btusb
E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Signed-off-by: Ian Mackinnon <imackinnon@gmail.com>
Tested-By: Aathif Naseer <aathif394@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
strcpy() performs no bounds checking on the destination buffer. This
could result in linear overflows beyond the end of the buffer, leading
to all kinds of misbehaviors. The safe replacement is strscpy() but in
this case it is better to use the scnprintf to simplify the arithmetic.
This is a previous step in the path to remove the strcpy() function
entirely from the kernel.
Signed-off-by: Len Baker <len.baker@gmx.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
File-scope struct nfcmrvl_if_ops is not modified so can be made const.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several functions do not modify pointed data so arguments and local
variables can be const for correctness and safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several functions do not modify pointed data so arguments and local
variables can be const for correctness and safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several functions do not modify pointed data so arguments and local
variables can be const for correctness and safety. This allows also
making file-scope nci_core_get_config_otp_ram_version array const.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Loop iterators are simple integers, no point to optimize the size and
use u8. It only raises the question whether the variable is used in
some other context.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Size of firmware is a type of size_t, so print it directly instead of
casting to int.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
nfcsim_abort_cmd() does not modify struct nfcsim, so local variable
can be a pointer to const.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
virtual_ncidev_ioctl() does not modify struct nfc_dev, so local variable
can be a pointer to const.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several functions do not modify pointed data so arguments and local
variables can be const for correctness and safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several functions do not modify pointed data so arguments and local
variables can be const for correctness and safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Edmund Dea
Gustavo A. R. Silva
Sergio Paracuellos
Lucas De Marchi
Khaled Almahallawy
Animesh Manna
Gwan-gyeong Mun
Matt Roper
Andy Shevchenko
Len Baker
Fabio Aiuto
Anirudh Rayabharam
Krzysztof Kozlowski
Zhiyong Tao
Sherry Sun
Tony Lindgren
Rikard Falkeborn
Konrad Dybcio
Shai Malin
Vladimir Oltean
Jeremy Kerr
Willy Tarreau
Ian Mackinnon