| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This reverts commit cf8331825a8d10e46fa574fdf015a65cb5a6db86.
There are better Linux interfaces to export the different LED modes
and blinking reasons.
Revert this patch for now and come up with better solution later.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Link: https://lore.kernel.org/r/20210719101640.16047-1-kurt@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pull EFI fixes for v5.14-rc2 from Ard Biesheuvel:
" - Ensure that memblock reservations and IO reserved resources remain in
sync when using the EFI memreserve feature.
- Don't complain about invalid TPM final event log table if it is
missing altogether.
- Comment header fix for the stub.
- Avoid a spurious warning when attempting to reserve firmware memory
that is already reserved in the first place."
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This patch adds to support phy-exynosautov9-ufs driver for ExynosAuto v9
series SoCs. The patch adds "samsung,exynosautov9-ufs-phy" compatible.
Unlike previous exynos ufs phy, the chip uses 0x50 offset as
PHY_TRSV_REG_CFG_OFFSET.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210709094524.110193-3-chanho61.park@samsung.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Instead of using exynos7 ufs definition in phy-exynos7-ufs.h, we should
put it into phy-exynos7-ufs.c to be included different objects or units.
Suggested-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210709094524.110193-2-chanho61.park@samsung.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Currently, VF doesn't enable rx VLAN offload when initializating,
and PF does it for VFs. If user disable the rx VLAN offload for
VF with ethtool -K, and reload the VF driver, it may cause the
rx VLAN offload state being inconsistent between hardware and
software.
Fixes it by enabling rx VLAN offload when VF initializing.
Fixes: e2cb1dec9779 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
For hardware limitation, port VLAN filter is port level, and
effective for all the functions of the port. So if not support
port VLAN bypass, it's necessary to disable the port VLAN filter,
in order to support function level VLAN filter control.
Fixes: 2ba306627f59 ("net: hns3: add support for modify VLAN filter state")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When VF need response from PF, VF will wait (1us - 1s) to receive
the response, or it will wait timeout and the VF action fails.
If VF do not receive response in 1st action because timeout,
the 2nd action may receive response for the 1st action, and get
incorrect response data.VF must reciveve the right response from
PF,or it will cause unexpected error.
This patch adds match_id to check mailbox response from PF to VF,
to make sure VF get the right response:
1. The message sent from VF was labelled with match_id which was a
unique 16-bit non-zero value.
2. The response sent from PF will label with match_id which got from
the request.
3. The VF uses the match_id to match request and response message.
This scheme depends on PF driver supports match_id, if PF driver doesn't
support then VF will uses the original scheme.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, the mailbox synchronous communication between VF and PF use
the following fields to maintain communication:
1. Origin_mbx_msg which was combined by message code and subcode, used
to match request and response.
2. Received_resp which means whether received response.
There may possible mismatches of the following situation:
1. VF sends message A with code=1 subcode=1.
2. PF was blocked about 500ms when processing the message A.
3. VF will detect message A timeout because it can't get the response
within 500ms.
4. VF sends message B with code=1 subcode=1 which equal message A.
5. PF processes the first message A and send the response message to
VF.
6. VF will identify the response matched the message B because the
code/subcode is the same. This will lead to mismatch of request and
response.
To fix the above bug, we use the following scheme:
1. The message sent from VF was labelled with match_id which was a
unique 16-bit non-zero value.
2. The response sent from PF will label with match_id which got from
the request.
3. The VF uses the match_id to match request and response message.
As for PF driver, it only needs to copy the match_id from request to
response.
Fixes: dde1a86e93ca ("net: hns3: Add mailbox support to PF driver")
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Dmabuf sysfs stat is used for dmabuf info track.
But these file maybe still in use after buffer released,
should clear it before buffer release.
Signed-off-by: Guangming Cao <Guangming.Cao@mediatek.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210720103158.83439-1-guangming.cao@mediatek.com
Signed-off-by: Christian König <christian.koenig@amd.com>
|
|
The Qualcomm SC8180x platform has 4 PCIe controllers and PHYs, typically
used to connect things such as a modem or NVME storage device. Add the
programming sequence to get the PHYs up and running.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210629004509.1788286-2-bjorn.andersson@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
It's a noop on DG1, and in the future when need to support other devices
which let us control the coherency, then it should be an immutable
creation time property for the BO. This will likely be controlled
through a new gem_create_ext extension.
v2: add some kernel doc for the discrete changes, and document the
implicit rules
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Kenneth Graunke <kenneth@whitecape.org>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210715101536.2606307-2-matthew.auld@intel.com
|
|
Replace pci_enable_device() with pcim_enable_device(),
pci_disable_device() will be called in release automatically.
v3:
reformat commit message
update for move to tiny/
v2:
use pcim_enable_device()
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210715132845.2415619-1-yangyingliang@huawei.com
|
|
[Bug][AST2500]
V1:
When AST2500 acts as stand-alone VGA so that DRAM and DVO initialization
have to be achieved by VGA driver with P2A (PCI to AHB) enabling.
However, HW suggests disable Fast reset mode after DRAM initializaton,
because fast reset mode is mainly designed for ARM ICE debugger.
Once Fast reset is checked as enabling, WDT (Watch Dog Timer) should be
first enabled to avoid system deadlock before disable fast reset mode.
V2:
Use to_pci_dev() to get revision of PCI configuration.
V3:
If SCU00 is not unlocked, just enter its password again.
It is unnecessary to clear AHB lock condition and restore WDT default
setting again, before Fast-reset clearing.
V4:
repatch after "error : could not build fake ancestor" resolved.
V5:
Since CVE_2019_6260 item3, Most of AST2500 have disabled P2A(PCIe to AMBA).
However, for backward compatibility, some patches about P2A, such as items
of v5.2 and v5.3, are considered to be upstreamed with comments.
1. Add define macro to improve source readability.
ast_drv.h, ast_main.c, ast_post.c
2. Add comment about "Fast restet" is enabled for ARM-ICE debugger
ast_post.c
3. Add comment about Reset USB port to patch USB unknown device issue
ast_post.c
Signed-off-by: KuoHsiang Chou <kuohsiang_chou@aspeedtech.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210709080900.4056-1-kuohsiang_chou@aspeedtech.com
|
|
The function ast_get_modes() will also return 0, when it try to get the
edid, but it also do not get the edid.
Signed-off-by: Ainux.Wang <ainux.wang@gmail.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210716015615.9150-1-ainux.wang@gmail.com
|
|
The DMA-BUF attachment statistics form a subset of the DMA-BUF
sysfs statistics that recently merged to the drm-misc tree. They are not
UABI yet since they have not merged to the upstream Linux kernel.
Since there has been a reported a performance regression due to the
overhead of sysfs directory creation/teardown during
dma_buf_attach()/dma_buf_detach(), this patch deletes the DMA-BUF
attachment statistics from sysfs.
Fixes: bdb8d06dfefd ("dmabuf: Add the capability to expose DMA-BUF stats in sysfs")
Signed-off-by: Hridya Valsaraju <hridya@google.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210713040742.2680135-1-hridya@google.com
Signed-off-by: Christian König <christian.koenig@amd.com>
|
|
One of the SUSE QA tests triggered:
localhost kernel: efi: Failed to lookup EFI memory descriptor for 0x000000003dcf8000
which comes from x86's version of efi_arch_mem_reserve() trying to
reserve a memory region. Usually, that function expects
EFI_BOOT_SERVICES_DATA memory descriptors but the above case is for the
MOKvar table which is allocated in the EFI shim as runtime services.
That lead to a fix changing the allocation of that table to boot services.
However, that fix broke booting SEV guests with that shim leading to
this kernel fix
8d651ee9c71b ("x86/ioremap: Map EFI-reserved memory as encrypted for SEV")
which extended the ioremap hint to map reserved EFI boot services as
decrypted too.
However, all that wasn't needed, IMO, because that error message in
efi_arch_mem_reserve() was innocuous in this case - if the MOKvar table
is not in boot services, then it doesn't need to be reserved in the
first place because it is, well, in runtime services which *should* be
reserved anyway.
So do that reservation for the MOKvar table only if it is allocated
in boot services data. I couldn't find any requirement about where
that table should be allocated in, unlike the ESRT which allocation is
mandated to be done in boot services data by the UEFI spec.
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
Set DSC BPP to the value forced through
debugfs. It can go from bpc to bpp-1.
v2: Use default dsc bpp when we are just
doing force_dsc_en, use default dsc bpp
for invalid force_dsc_bpp values. (Jani)
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Swati Sharma <swati2.sharma@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210720064907.9771-4-vandita.kulkarni@intel.com
|
|
This patch creates a per connector debugfs node to expose
the Compressed BPP. The same node can be used from userspace
to force DSC to a certain BPP(all accepted values).
This is useful to verify all supported/requested
compression bpp's through IGT
v2: Remove unnecessary logic (Jani)
v3: Drop pipe bpp in debugfs node (Vandita)
v4: Minor cleanups (Vandita)
v5: Fix NULL pointer dereference
v6: Fix dim tool checkpatch errors
Release the lock before return (Vandita)
v7: Rename to file to dsc_bpp, remove unwanted
dsc bpp range check from v6, permissions (Jani)
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Navare Manasi D <manasi.d.navare@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Patnana Venkata Sai <venkata.sai.patnana@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210720064907.9771-3-vandita.kulkarni@intel.com
|
|
Though there is a write option available on fec_suport
debugfs file, so far it has been registering with read
permissions only.
Suggested-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210720064907.9771-2-vandita.kulkarni@intel.com
|
|
Fix comments for GE CS1000 CP210x USB ID assignments.
Fixes: 42213a0190b5 ("USB: serial: cp210x: add some more GE USB IDs")
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Link: https://lore.kernel.org/r/20210714182847.50360-10-don.brace@microchip.com
Reviewed-by: Kevin Barnett <kevin.barnett@microchip.com>
Reviewed-by: Mike McGowen <mike.mcgowen@microchip.com>
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Gerry Morong <gerry.morong@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Correct driver's ISR accessing a data structure member that has not been
fully initialized during driver initialization.
The pqi queue groups can have uninitialized members when an interrupt
fires. This has not resulted in any driver crashes. This was found during
our own internal testing. No bugs were ever filed.
Link: https://lore.kernel.org/r/20210714182847.50360-9-don.brace@microchip.com
Reviewed-by: Kevin Barnett <kevin.barnett@microchip.com>
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Signed-off-by: Mike McGowen <mike.mcgowen@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add support for ZTE RM241-18i 2G device ID:
VID_9005, DID_028F, SVID_1CF2 and SDID_5445
Add support for ZTE RM242-18i 4G device ID:
VID_9005, DID_028F, SVID_1CF2 and SDID_5446
Add support for ZTE RM243-18i device ID:
VID_9005, DID_028F, SVID_1CF2 and SDID_5447
Add support for ZTE SDPSA/B-18i 4G device ID:
VID_9005, DID_028F, SVID_1CF2 and SDID_0B27
Add support for ZTE SDPSA/B_I-18i device ID:
VID_9005, DID_028F, SVID_1CF2 and SDID_0B29
Add support for ZTE SDPSA/B_L-18i 2G device ID:
VID_9005, DID_028F, SVID_1CF2 and SDID_0B45
Link: https://lore.kernel.org/r/20210714182847.50360-8-don.brace@microchip.com
Reviewed-by: Kevin Barnett <kevin.barnett@microchip.com>
Reviewed-by: Mike McGowen <mike.mcgowen@microchip.com>
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Signed-off-by: Balsundar P <balsundar.p@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add support for Norsi ntcom Raid-24i controller:
VID_0x9005, DID_0x028f, SVID_0x1dfc, SDID_0x3161
Link: https://lore.kernel.org/r/20210714182847.50360-7-don.brace@microchip.com
Reviewed-by: Kevin Barnett <kevin.barnett@microchip.com>
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Signed-off-by: Mike McGowen <mike.mcgowen@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Report on SCSI command that has triggered the reset. Also add check for
NULL SCSI commands resulting from issuing sg_reset when there is no
outstanding commands.
Example:
sg_reset -d /dev/sgXY
smartpqi 0000:39:00.0: resetting scsi 4:0:1:0 due to cmd 0x12
Link: https://lore.kernel.org/r/20210714182847.50360-6-don.brace@microchip.com
Reviewed-by: Kevin Barnett <kevin.barnett@microchip.com>
Reviewed-by: Mike McGowen <mike.mcgowen@microchip.com>
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Signed-off-by: Murthy Bhat <Murthy.Bhat@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Change Microsemi to Microchip.
Link: https://lore.kernel.org/r/20210714182847.50360-5-don.brace@microchip.com
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Gerry Morong <gerry.morong@microchip.com>
Reviewed-by: Justin Lindley <Justin.lindley@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Change driver module macros to reflect copyright changes: Microsemi to
Microchip.
Link: https://lore.kernel.org/r/20210714182847.50360-4-don.brace@microchip.com
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Gerry Morong <gerry.morong@microchip.com>
Reviewed-by: Justin Lindley <Justin.lindley@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Updated copyright notices and company name strings to reflect Microchip
ownership.
Link: https://lore.kernel.org/r/20210714182847.50360-3-don.brace@microchip.com
Reviewed-by: Mike McGowen <mike.mcgowen@microchip.com>
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add support for H3C P4408-Ma-8i-2GB device ID:
VID_9005, DID_028F, SVID_193D and SDID_1108
VID_9005, DID_028F, SVID_193D and SDID_1109
Link: https://lore.kernel.org/r/20210714182847.50360-2-don.brace@microchip.com
Reviewed-by: Kevin Barnett <kevin.barnett@microchip.com>
Reviewed-by: Mike McGowen <mike.mcgowen@microchip.com>
Reviewed-by: Murthy Bhat <Murthy.Bhat@microchip.com>
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Signed-off-by: Mahesh Rajashekhara <mahesh.rajashekhara@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The IOC firmware assumes that the host driver is still alive after shutdown
and continues to post events to host memory (due to faulty expander phy
links, etc). This leads to 0x2666 (a bus fault occurred during a host-IOC
memory access).
Perform an IOC soft reset as part of shutdown to disable event posting.
Link: https://lore.kernel.org/r/20210705145951.32258-1-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Fix an 11-year old bug in ngene_command_config_free_buf() while
addressing the following warnings caught with -Warray-bounds:
arch/alpha/include/asm/string.h:22:16: warning: '__builtin_memcpy' offset [12, 16] from the object at 'com' is out of the bounds of referenced subobject 'config' with type 'unsigned char' at offset 10 [-Warray-bounds]
arch/x86/include/asm/string_32.h:182:25: warning: '__builtin_memcpy' offset [12, 16] from the object at 'com' is out of the bounds of referenced subobject 'config' with type 'unsigned char' at offset 10 [-Warray-bounds]
The problem is that the original code is trying to copy 6 bytes of
data into a one-byte size member _config_ of the wrong structue
FW_CONFIGURE_BUFFERS, in a single call to memcpy(). This causes a
legitimate compiler warning because memcpy() overruns the length
of &com.cmd.ConfigureBuffers.config. It seems that the right
structure is FW_CONFIGURE_FREE_BUFFERS, instead, because it contains
6 more members apart from the header _hdr_. Also, the name of
the function ngene_command_config_free_buf() suggests that the actual
intention is to ConfigureFreeBuffers, instead of ConfigureBuffers
(which takes place in the function ngene_command_config_buf(), above).
Fix this by enclosing those 6 members of struct FW_CONFIGURE_FREE_BUFFERS
into new struct config, and use &com.cmd.ConfigureFreeBuffers.config as
the destination address, instead of &com.cmd.ConfigureBuffers.config,
when calling memcpy().
This also helps with the ongoing efforts to globally enable
-Warray-bounds and get us closer to being able to tighten the
FORTIFY_SOURCE routines on memcpy().
Link: https://github.com/KSPP/linux/issues/109
Fixes: dae52d009fc9 ("V4L/DVB: ngene: Initial check-in")
Cc: stable@vger.kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/linux-hardening/20210420001631.GA45456@embeddedor/
|
|
The SM4250/6115 have 4 rpm power domains, ported from downstream DT.
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Link: https://lore.kernel.org/r/20210627185927.695411-6-iskren.chernev@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Switch to use module_parport_driver() to reduce boilerplate code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210616140432.39406-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Given that all serio drivers except one implement write() method
let's make it mandatory to avoid testing for its presence whenever
we attempt to use it.
Link: https://lore.kernel.org/r/YFgUxG/TljMuVeQ3@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The NSLU2 has been migrated to devicetree and there we use
the gpio-beeper.c driver instead, the boardfile will be deleted
for kernel v5.15 so drop this custom and now unneeded driver.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210714115028.916360-1-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Drop the DRM IRQ midlayer in favor of Linux IRQ interfaces. DRM's
IRQ helpers are mostly useful for UMS drivers. Modern KMS drivers
don't benefit from using it.
This patch also fixes a bug where the driver didn't release the
IRQ.
v2:
* automatically release IRQ via devm_request_irq() (Paul)
* mention the bugfix (Sam)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20210715100258.6638-1-tzimmermann@suse.de
|
|
In "qmp_cooling_devices_register", the count value is initially
QMP_NUM_COOLING_RESOURCES, which is 2. Based on the initial count value,
the memory for cooling_devs is allocated. Then while calling the
"qmp_cooling_device_add" function, count value is post-incremented for
each child node.
This makes the out of bound access to the cooling_dev array. Fix it by
passing the QMP_NUM_COOLING_RESOURCES definition to devm_kzalloc() and
initializing the count to 0.
While at it, let's also free the memory allocated to cooling_dev if no
cooling device is found in DT and during unroll phase.
Cc: stable@vger.kernel.org # 5.4
Fixes: 05589b30b21a ("soc: qcom: Extend AOSS QMP driver to support resources that are used to wake up the SoC.")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210629153249.73428-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Allow the qcom_scm driver to be loadable as a permenent module.
This still uses the "depends on QCOM_SCM || !QCOM_SCM" bit to
ensure that drivers that call into the qcom_scm driver are
also built as modules. While not ideal in some cases its the
only safe way I can find to avoid build errors without having
those drivers select QCOM_SCM and have to force it on (as
QCOM_SCM=n can be valid for those drivers).
Reviving this now that Saravana's fw_devlink defaults to on,
which should avoid loading troubles seen before.
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Will Deacon <will@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Link: https://lore.kernel.org/r/20210707045320.529186-1-john.stultz@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Let's skip printing anything if there's nothing to see. This makes it so
the file length is 0 instead of 1, for the newline, and helps scripts
figure out if there's anything to see in these files.
Cc: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210628030150.2627905-1-swboyd@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
rpmhpd_aggregate_corner() takes a corner as parameter, but in
rpmhpd_power_off() the code requests the level of the first corner
instead.
In all (known) current cases the first corner has level 0, so this
change should be a nop, but in case that there's a power domain with a
non-zero lowest level this makes sure that rpmhpd_power_off() actually
requests the lowest level - which is the closest to "power off" we can
get.
While touching the code, also skip the unnecessary zero-initialization
of "ret".
Fixes: 279b7e8a62cc ("soc: qcom: rpmhpd: Add RPMh power domain driver")
Reviewed-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Tested-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20210703005416.2668319-2-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
It seems we don't need platform specific implementation for the AOSS
QMP, so let's introduce a generic compatible to avoid having to update
the driver for each platform.
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Tested-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20210709174142.1274554-4-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
refcount_t type and corresponding API can protect refcounters from
accidental underflow and overflow and further use-after-free situations.
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1626674392-55857-1-git-send-email-xiyuyang19@fudan.edu.cn
|
|
The user can pass in any value to the driver through the 'ioctl'
interface. The driver dost not check, which may cause DoS bugs.
The following log reveals it:
divide error: 0000 [#1] PREEMPT SMP KASAN PTI
RIP: 0010:SetOverlayViewPort+0x133/0x5f0 drivers/video/fbdev/kyro/STG4000OverlayDevice.c:476
Call Trace:
kyro_dev_overlay_viewport_set drivers/video/fbdev/kyro/fbdev.c:378 [inline]
kyrofb_ioctl+0x2eb/0x330 drivers/video/fbdev/kyro/fbdev.c:603
do_fb_ioctl+0x1f3/0x700 drivers/video/fbdev/core/fbmem.c:1171
fb_ioctl+0xeb/0x130 drivers/video/fbdev/core/fbmem.c:1185
vfs_ioctl fs/ioctl.c:48 [inline]
__do_sys_ioctl fs/ioctl.c:753 [inline]
__se_sys_ioctl fs/ioctl.c:739 [inline]
__x64_sys_ioctl+0x19b/0x220 fs/ioctl.c:739
do_syscall_64+0x32/0x80 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x44/0xae
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1626235762-2590-1-git-send-email-zheyuma97@gmail.com
|
|
As of now any communication between CGXs PFs and
their VFs within the system is possible only by
external switches sending packets back to the
system. This patch adds internal switching support.
Broadcast packet replication is not covered here.
RVU admin function (AF) maintains MAC addresses
of all interfaces in the system. When switching is
enabled, MCAM entries are allocated to install rules
such that packets with DMAC matching any of the
internal interface MAC addresses is punted back
into the system via the loopback channel.
On the receive side the default unicast rules
are modified to not check for ingress channel.
So any packet with matching DMAC irrespective of
which interface it is coming from will be forwarded
to the respective PF/VF interface.
The transmit side rules and default unicast rules
are updated if user changes MAC address of an interface.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
AF till now only manages the allocation and freeing of
MCAM rules for other PF/VFs in system. To implement
L2 switching between all CGX mapped PF and VFs, AF
requires MCAM entries for DMAC rules for each PF and VF.
This patch modifies AF driver such that AF can also
allocate MCAM rules and install rules for other
PFs and VFs. All the checks like channel verification
for RX rules and PF_FUNC verification for TX rules are
relaxed in case AF is allocating or installing rules.
Also all the entry and counter to owner mappings are
set to NPC_MCAM_INVALID_MAP when they are free indicating
those are not allocated to AF nor PF/VFs.
This patch also ensures that AF allocated and installed
entries are displayed in debugfs.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For enabling VF-VF switching the packets egressing
out of CGX mapped VFs needed to be sent to LBK
so that same packets are received back to the system.
But the LBK link also needs to be enabled in addition
to a VF's mapped CGX_LMAC link otherwise hardware
raises send error interrupt indicating selected LBK
link is not enabled in NIX_AF_TL3_TL2X_LINKX_CFG register.
Hence this patch enables all LBK links in
TL3_TL2_LINKX_CFG registers.
Also to enable packet flow between PFs/VFs of NIX0
to PFs/VFs of NIX1(in 98xx silicon) the NPC TX DMAC
rules has to be installed such that rules must be hit
for any TX interface i.e., NIX0-TX or NIX1-TX provided
DMAC match creteria is met. Hence this patch changes the
behavior such that MCAM is programmed to match with any
NIX0/1-TX interface for TX rules.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Building on ARCH=arc causes a "redefined" warning, so rename this
driver's CACHE_LINE_MASK to avoid the warning.
../drivers/net/ethernet/hisilicon/hip04_eth.c:134: warning: "CACHE_LINE_MASK" redefined
134 | #define CACHE_LINE_MASK 0x3F
In file included from ../include/linux/cache.h:6,
from ../include/linux/printk.h:9,
from ../include/linux/kernel.h:19,
from ../include/linux/list.h:9,
from ../include/linux/module.h:12,
from ../drivers/net/ethernet/hisilicon/hip04_eth.c:7:
../arch/arc/include/asm/cache.h:17: note: this is the location of the previous definition
17 | #define CACHE_LINE_MASK (~(L1_CACHE_BYTES - 1))
Fixes: d413779cdd93 ("net: hisilicon: Add an tx_desc to adapt HI13X1_GMAC")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The security restrictions on the FSI-attached SPI controllers have
been applied universally to all controllers, so the controller can no
longer transfer more than 8 bytes for one transfer. Refactor the driver
to remove the looping and support for larger transfers, and remove the
"restricted" compatible string, as all the controllers are now
considered restricted.
Eddie James (2):
spi: fsi: Reduce max transfer size to 8 bytes
dt-bindings: fsi: Remove ibm,fsi2spi-restricted compatible
.../devicetree/bindings/fsi/ibm,fsi2spi.yaml | 1 -
drivers/spi/spi-fsi.c | 125 +++---------------
2 files changed, 22 insertions(+), 104 deletions(-)
--
2.27.0
|
|
To avoid races between iavf_init_task(), iavf_reset_task(),
iavf_watchdog_task(), iavf_adminq_task() as well as the shutdown and
remove functions more locking is required.
The current protection by __IAVF_IN_CRITICAL_TASK is needed in
additional places.
- The reset task performs state transitions, therefore needs locking.
- The adminq task acts on replies from the PF in
iavf_virtchnl_completion() which may alter the states.
- The init task is not only run during probe but also if a VF gets stuck
to reinitialize it.
- The shutdown function performs a state transition.
- The remove function performs a state transition and also free's
resources.
iavf_lock_timeout() is introduced to avoid waiting infinitely
and cause a deadlock. Rather unlock and print a warning.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The iavf watchdog task overrides adapter->state to __IAVF_RESETTING
when it detects a pending reset. Then schedules iavf_reset_task() which
takes care of the reset.
The reset task is capable of handling the reset without changing
adapter->state. In fact we lose the state information when the watchdog
task prematurely changes the adapter state. This may lead to a crash if
instead of the reset task the iavf_remove() function gets called before
the reset task.
In that case (if we were in state __IAVF_RUNNING previously) the
iavf_remove() function triggers iavf_close() which fails to close the
device because of the incorrect state information.
This may result in a crash due to pending interrupts.
kernel BUG at drivers/pci/msi.c:357!
[...]
Call Trace:
[<ffffffffbddf24dd>] pci_disable_msix+0x3d/0x50
[<ffffffffc08d2a63>] iavf_reset_interrupt_capability+0x23/0x40 [iavf]
[<ffffffffc08d312a>] iavf_remove+0x10a/0x350 [iavf]
[<ffffffffbddd3359>] pci_device_remove+0x39/0xc0
[<ffffffffbdeb492f>] __device_release_driver+0x7f/0xf0
[<ffffffffbdeb49c3>] device_release_driver+0x23/0x30
[<ffffffffbddcabb4>] pci_stop_bus_device+0x84/0xa0
[<ffffffffbddcacc2>] pci_stop_and_remove_bus_device+0x12/0x20
[<ffffffffbddf361f>] pci_iov_remove_virtfn+0xaf/0x160
[<ffffffffbddf3bcc>] sriov_disable+0x3c/0xf0
[<ffffffffbddf3ca3>] pci_disable_sriov+0x23/0x30
[<ffffffffc0667365>] i40e_free_vfs+0x265/0x2d0 [i40e]
[<ffffffffc0667624>] i40e_pci_sriov_configure+0x144/0x1f0 [i40e]
[<ffffffffbddd5307>] sriov_numvfs_store+0x177/0x1d0
Code: 00 00 e8 3c 25 e3 ff 49 c7 86 88 08 00 00 00 00 00 00 5b 41 5c 41 5d 41 5e 41 5f 5d c3 48 8b 7b 28 e8 0d 44
RIP [<ffffffffbbbf1068>] free_msi_irqs+0x188/0x190
The solution is to not touch the adapter->state in iavf_watchdog_task()
and let the reset task handle the state transition.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
Kurt Kanzenbach
Ingo Molnar
Chanho Park
Jian Shen
Peng Li
Chengwen Feng
Guangming Cao
Bjorn Andersson
Matthew Auld
Yang Yingliang
KuoHsiang Chou
Ainux.Wang
Hridya Valsaraju
Borislav Petkov
Vandita Kulkarni
Patnana Venkata Sai
Ian Ray
Don Brace
Mike McGowen
Balsundar P
Murthy Bhat
Kevin Barnett
Mahesh Rajashekhara
Sreekanth Reddy
Gustavo A. R. Silva
Iskren Chernev
Andy Shevchenko
Dmitry Torokhov
Linus Walleij
Thomas Zimmermann
Manivannan Sadhasivam
John Stultz
Stephen Boyd
Xiyu Yang
Zheyu Ma
Subbaraya Sundeep
Randy Dunlap
Mark Brown
Stefan Assmann