| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Add device HID AMDI0022 to the AMD UART controller driver match table
and create a platform device for it. This controller can be found on
Microsoft Surface Laptop 4 devices and seems similar enough that we can
just copy the existing AMDI0020 entries.
Cc: <stable@vger.kernel.org> # 5.10+
Tested-by: Sachi King <nakato@nakato.io>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com> # for 8250_dw part
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Link: https://lore.kernel.org/r/20210512210413.1982933-1-luzmaximilian@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Receive FIFO Data Count Trigger field (RTRG[6:0]) in the Receive
FIFO Data Count Trigger Register (HSRTRGR) of HSCIF can only hold values
ranging from 0-127. As the FIFO size is equal to 128 on HSCIF, the user
can write an out-of-range value, touching reserved bits.
Fix this by limiting the trigger value to the FIFO size minus one.
Reverse the order of the checks, to avoid rx_trig becoming zero if the
FIFO size is one.
Note that this change has no impact on other SCIF variants, as their
maximum supported trigger value is lower than the FIFO size anyway, and
the code below takes care of enforcing these limits.
Fixes: a380ed461f66d1b8 ("serial: sh-sci: implement FIFO threshold register setting")
Reported-by: Linh Phung <linh.phung.jy@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/5eff320aef92ffb33d00e57979fd3603bbb4a70f.1620648218.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The commit that added this check did so in a very strange way - first
security_locked_down() is called, its value stored into retval, and if
it's nonzero, then an additional check is made for (change_irq ||
change_port), and if this is true, the function returns. However, if
the goto exit branch is not taken, the code keeps the retval value and
continues executing the function. Then, depending on whether
uport->ops->verify_port is set, the retval value may or may not be reset
to zero and eventually the error value from security_locked_down() may
abort the function a few lines below.
I will go out on a limb and assume that this isn't the intended behavior
and that an error value from security_locked_down() was supposed to
abort the function only in case (change_irq || change_port) is true.
Note that security_locked_down() should be called last in any series of
checks, since the SELinux implementation of this hook will do a check
against the policy and generate an audit record in case of denial. If
the operation was to carry on after calling security_locked_down(), then
the SELinux denial record would be bogus.
See commit 59438b46471a ("security,lockdown,selinux: implement SELinux
lockdown") for how SELinux implements this hook.
Fixes: 794edf30ee6c ("lockdown: Lock down TIOCSSERIAL")
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210507115719.140799-1-omosnace@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently the expression lsr | UART_LSR_TEMT is always true and
this seems suspect. I believe the intent was to mask lsr with UART_LSR_TEMT
to check that bit, so the expression should be using the & operator
instead. Fix this.
Fixes: b9c2470fb150 ("serial: tegra: flush the RX fifo on frame error")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210426105514.23268-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Line disciplines expect a positive value or zero returned from
tty->ops->write_room (invoked by tty_write_room). So make this
assumption explicit by using unsigned int as a return value. Both of
tty->ops->write_room and tty_write_room.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Acked-by: Alex Elder <elder@linaro.org>
Acked-by: Max Filippov <jcmvbkbc@gmail.com> # xtensa
Acked-by: David Sterba <dsterba@suse.com>
Acked-By: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Chris Zankel <chris@zankel.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Cc: Jens Taprogge <jens.taprogge@taprogge.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Scott Branden <scott.branden@broadcom.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: David Lin <dtwlin@gmail.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Link: https://lore.kernel.org/r/20210505091928.22010-23-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Don't access tty->ops->write_room directly, use tty_write_room helper
instead.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210505091928.22010-22-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the classic failpath handling using gotos in st_core_init. That way,
tty_unregister_ldisc needs not be repeated on two places.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210505091928.22010-21-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Now that noone checks the return value of tty_unregister_ldisc, make the
function return 'void'.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210505091928.22010-20-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
tty_unregister_ldisc now returns 0 = success. No need to check the
return value. In fact, the users only warned if an error occured and
didn't do anything useful anyway -- the ldisc module was unloaded in any
case.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: William Hubbs <w.d.hubbs@gmail.com>
Cc: Chris Brannon <chris@the-brannons.com>
Cc: Kirk Reiser <kirk@reisers.ca>
Cc: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Andreas Koensgen <ajk@comnets.uni-bremen.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Rodolfo Giometti <giometti@enneenne.com>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Link: https://lore.kernel.org/r/20210505091928.22010-19-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The refcount is checked only in tty_unregister_ldisc and EBUSY returned
if it is nonzero. But none of the tty_unregister_ldisc callers act
anyhow if this (or any other) error is returned. So remove
tty_ldisc_ops::refcount completely and make tty_unregister_ldisc return
'void' in the next patches. That means we assume tty_unregister_ldisc is
not called while the ldisc might be in use. That relies on
try_module_get in get_ldops and module_put in put_ldops.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210505091928.22010-18-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make tty_unregister_ldisc symmetric to tty_register_ldisc by accepting
struct tty_ldisc_ops as a parameter instead of ldisc number. This avoids
checking of the ldisc number bounds in tty_unregister_ldisc.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: William Hubbs <w.d.hubbs@gmail.com>
Cc: Chris Brannon <chris@the-brannons.com>
Cc: Kirk Reiser <kirk@reisers.ca>
Cc: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Andreas Koensgen <ajk@comnets.uni-bremen.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Rodolfo Giometti <giometti@enneenne.com>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Link: https://lore.kernel.org/r/20210505091928.22010-17-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the classic failpath handling using gotos in gsm_init. That way,
tty_unregister_ldisc needs not be repeated on two places.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210505091928.22010-16-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is no reason to pass the ldisc number to tty_register_ldisc
separately. Just set it in the already defined tty_ldisc_ops in all the
ldiscs.
This simplifies tty_register_ldisc a bit too (no need to set the num
member there).
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: William Hubbs <w.d.hubbs@gmail.com>
Cc: Chris Brannon <chris@the-brannons.com>
Cc: Kirk Reiser <kirk@reisers.ca>
Cc: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Andreas Koensgen <ajk@comnets.uni-bremen.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Rodolfo Giometti <giometti@enneenne.com>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Link: https://lore.kernel.org/r/20210505091928.22010-15-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Group the ctrl members under a single struct called ctrl. The new struct
contains 'pgrp', 'session', 'pktstatus', and 'packet'. 'pktstatus' and
'packet' used to be bits in a bitfield. The struct also contains the
lock protecting them to share the same cache line.
Note that commit c545b66c6922b (tty: Serialize tcflow() with other tty
flow control changes) added a padding to the original bitfield. It was
for the bitfield to occupy a whole 64b word to avoid interferring stores
on Alpha (cannot we evaporate this arch with weird implications to C
code yet?). But it doesn't work as expected as the padding
(tty_struct::ctrl_unused) is aligned to a 8B boundary too and occupies
some bytes from the next word.
So make it reliable by:
1) setting __aligned of the struct -- that aligns the start, and
2) making 'unsigned long unused[0]' as the last member of the struct --
pads the end.
Add a kerneldoc comment for this grouped members.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: netdev@vger.kernel.org
Link: https://lore.kernel.org/r/20210505091928.22010-14-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Group the flow flags under a single struct called flow. The new struct
contains 'stopped' and 'tco_stopped' bools which used to be bits in a
bitfield. The struct also contains the lock protecting them to
potentially share the same cache line.
Note that commit c545b66c6922b (tty: Serialize tcflow() with other tty
flow control changes) added a padding to the original bitfield. It was
for the bitfield to occupy a whole 64b word to avoid interferring stores
on Alpha (cannot we evaporate this arch with weird implications to C
code yet?). But it doesn't work as expected as the padding
(tty_struct::unused) is aligned to a 8B boundary too and occupies some
bytes from the next word.
So make it reliable by:
1) setting __aligned of the struct -- that aligns the start, and
2) making 'unsigned long unused[0]' as the last member of the struct --
pads the end.
This is also the perfect time to start the documentation of tty_struct
where all this lives. So we start by documenting what these bools
actually serve for. And why we do all the alignment dances. Only the few
up-to-date information from the Theodore's comment made it into this new
Kerneldoc comment.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: "Maciej W. Rozycki" <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/20210505091928.22010-13-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Char pointer (cp) passed to tty_ldisc_ops::receive_buf{,2} is const.
There is no reason for flag pointer (fp) not to be too. So switch it in
the definition and all uses.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: William Hubbs <w.d.hubbs@gmail.com>
Cc: Chris Brannon <chris@the-brannons.com>
Cc: Kirk Reiser <kirk@reisers.ca>
Cc: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Andreas Koensgen <ajk@comnets.uni-bremen.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20210505091928.22010-12-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A return at the end of a void-returning function is superfluous. Get rid
of it.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210505091928.22010-11-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Handle !TTY_NORMAL as a short path and 'continue' the loop. Do the rest as
a normal code flow. This decreases the indentation level by one and
makes the code flow more understandable.
IOW, we avoid
if (cond) {
LONG CODE;
} else
single_line();
by
if (!cond) {
single_line();
continue;
}
LONG CODE;
While at it, invert also the 'if (!test_bit) A else B' into 'if
(test_bit) B else A'.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210505091928.22010-10-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It might be confusing for readers: there are three distinct dereferences
and increments of 'cp' in n_tty_receive_buf_standard. Do it on a single
place, along with/before the 'fp' dereference.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210505091928.22010-9-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
After the previous patch, noone cares about the return value of
n_tty_receive_char_special. ldata->lnext is checked instead.
So switch return type of n_tty_receive_char_special to void.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210505091928.22010-8-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Move lnext handling from __receive_buf to n_tty_receive_buf_standard. It
simplifies the handling as it needs not fetching 'flag' and decrement
'count' in __receive_buf. Instead, all this is left up to the loop in
n_tty_receive_buf_standard which already does that.
This way, no need to repeat the action when n_tty_receive_char_special
returns true -- ldata->lnext is set there in that case, so the 'if
(ldata->lnext)' check is sufficient. The next patch will switch
n_tty_receive_char_special to return 'void'.
The result is much simplified code flow.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210505091928.22010-7-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
After the previous cleanup patches, parmrk_dbl parameter is always true
-- I_PARMRK is checked only in n_tty_receive_char now. So remove
parmrk_dbl completely.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210505091928.22010-6-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
After the previous patches, n_tty_receive_buf_standard and
n_tty_receive_buf_fast differ only in handling of tty line and input
controls. Unlike n_tty_receive_buf_fast, n_tty_receive_buf_standard
handles them all (I_ISTRIP, I_IUCLC, L_IEXTEN, L_EXTPROC, and I_PARMRK).
So remove n_tty_receive_buf_fast and let n_tty_receive_buf_standard do
the handling. Actually most of the tests are only moved from
__receive_buf to n_tty_receive_buf_standard.
Again, the code duplication is not worth the theoretical speedup.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210505091928.22010-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
n_tty_receive_char_fast is a copy of n_tty_receive_char with one
exception: PARMRK is not doubled in the former. Unify these two and
double PARMRK depending on a newly added parameter (bool parmrk_dbl).
I don't think the theoretical speedup is worth the code duplication.
Which is directly connected with maintenance burden.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210505091928.22010-4-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The wrapper was meant as an optimization in commits eb3e4668bd9e (n_tty:
Un-inline slow-path n_tty_receive_char()) and e60d27c4d8b3 (n_tty:
Factor LNEXT processing from per-char i/o path). But the current
compiler (gcc 10) inlines it anyway (as expected). Actually, I'm not
sure it ever didn't. It would need to be marked with the noinline
attribute.
So remove this useless wrapper.
And if we ever introduce something similar, we need confirming numbers
first.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210505091928.22010-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Noone stepped up in the past two years since it was marked as BROKEN by
commit c7084edc3f6d (tty: mark Siemens R3964 line discipline as BROKEN).
Remove the line discipline for good.
Three remarks:
* we remove also the uapi header (as noone is able to use that interface
anyway)
* we do *not* remove the N_R3964 constant definition from tty.h, so it
remains reserved.
* in_interrupt() check is now removed from vt's con_put_char. Noone else
calls tty_operations::put_char from interrupt context.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210505091928.22010-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
update suspend register settings in Non-DPG mode.
Signed-off-by: Sathishkumar S <sathishkumar.sundararaju@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
enable vcn mgcg flag for picasso.
Signed-off-by: Sathishkumar S <sathishkumar.sundararaju@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Screen flickers rapidly when two 4K 60Hz monitors are in use. This issue
doesn't happen when one monitor is 4K 60Hz (pixelclock 594MHz) and
another one is 4K 30Hz (pixelclock 297MHz).
The issue is gone after setting "power_dpm_force_performance_level" to
"high". Following the indication, we found that the issue occurs when
sclk is too low.
So resolve the issue by disabling sclk switching when there are two
monitors requires high pixelclock (> 297MHz).
v2:
- Only apply the fix to Oland.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Update the method of disabling VCN IP for specific SKU for navi1x ASIC,
it will judge whether should add the related IP at the function of
amdgpu_device_ip_block_add().
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Judgement whether to add an sw ip according to the harvest info.
v2: fix indentation (Alex)
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
It is stored in dynamically allocated memory, so sysfs_bin_attr_init() must
be called to initialize it. (Note: "initialization" only sets the .attr.key
member in this struct; it does not change the value of any other members.)
Otherwise, when CONFIG_DEBUG_LOCK_ALLOC=y this message appears during boot:
BUG: key ffff9248900cd148 has not been registered!
Fixes: 9037246bb2da ("drm/amd/display: Add sysfs interface for set/get srm")
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1586
Reported-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Signed-off-by: David Ward <david.ward@gatech.edu>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Create new structure SISLANDS_SMC_SWSTATE_SINGLE, as initialState.levels
and ACPIState.levels are never actually used as flexible arrays. Those
arrays can be used as simple objects of type
SISLANDS_SMC_HW_PERFORMANCE_LEVEL, instead.
Currently, the code fails because flexible array _levels_ in
struct SISLANDS_SMC_SWSTATE doesn't allow for code that accesses
the first element of initialState.levels and ACPIState.levels
arrays:
drivers/gpu/drm/amd/pm/powerplay/si_dpm.c:
4820: table->initialState.levels[0].mclk.vDLL_CNTL =
4821: cpu_to_be32(si_pi->clock_registers.dll_cntl);
...
5021: table->ACPIState.levels[0].mclk.vDLL_CNTL =
5022: cpu_to_be32(dll_cntl);
because such element cannot be accessed without previously allocating
enough dynamic memory for it to exist (which never actually happens).
So, there is an out-of-bounds bug in this case.
That's why struct SISLANDS_SMC_SWSTATE should only be used as type
for object driverState and new struct SISLANDS_SMC_SWSTATE_SINGLE is
created as type for objects initialState, ACPIState and ULVState.
Also, with the change from one-element array to flexible-array member
in commit 0e1aa13ca3ff ("drm/amd/pm: Replace one-element array with
flexible-array in struct SISLANDS_SMC_SWSTATE"), the size of
dpmLevels in struct SISLANDS_SMC_STATETABLE should be fixed to be
SISLANDS_MAX_SMC_PERFORMANCE_LEVELS_PER_SWSTATE instead of
SISLANDS_MAX_SMC_PERFORMANCE_LEVELS_PER_SWSTATE - 1.
Fixes: 0e1aa13ca3ff ("drm/amd/pm: Replace one-element array with flexible-array in struct SISLANDS_SMC_SWSTATE")
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Create new structure SISLANDS_SMC_SWSTATE_SINGLE, as initialState.levels
and ACPIState.levels are never actually used as flexible arrays. Those
arrays can be used as simple objects of type
SISLANDS_SMC_HW_PERFORMANCE_LEVEL, instead.
Currently, the code fails because flexible array _levels_ in
struct SISLANDS_SMC_SWSTATE doesn't allow for code that access
the first element of initialState.levels and ACPIState.levels
arrays:
4353 table->initialState.levels[0].mclk.vDLL_CNTL =
4354 cpu_to_be32(si_pi->clock_registers.dll_cntl);
...
4555 table->ACPIState.levels[0].mclk.vDLL_CNTL =
4556 cpu_to_be32(dll_cntl);
because such element cannot exist without previously allocating
any dynamic memory for it (which never actually happens).
That's why struct SISLANDS_SMC_SWSTATE should only be used as type
for object driverState and new struct SISLANDS_SMC_SWSTATE_SINGLE is
created as type for objects initialState, ACPIState and ULVState.
Also, with the change from one-element array to flexible-array member
in commit 96e27e8d919e ("drm/radeon/si_dpm: Replace one-element array
with flexible-array in struct SISLANDS_SMC_SWSTATE"), the size of
dpmLevels in struct SISLANDS_SMC_STATETABLE should be fixed to be
SISLANDS_MAX_SMC_PERFORMANCE_LEVELS_PER_SWSTATE instead of
SISLANDS_MAX_SMC_PERFORMANCE_LEVELS_PER_SWSTATE - 1.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1583
Fixes: 96e27e8d919e ("drm/radeon/si_dpm: Replace one-element array with flexible-array in struct SISLANDS_SMC_SWSTATE")
Cc: stable@vger.kernel.org
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Create new structure NISLANDS_SMC_SWSTATE_SINGLE, as initialState.levels
and ACPIState.levels are never actually used as flexible arrays. Those
arrays can be used as simple objects of type
NISLANDS_SMC_HW_PERFORMANCE_LEVEL, instead.
Currently, the code fails because flexible array _levels_ in
struct NISLANDS_SMC_SWSTATE doesn't allow for code that access
the first element of initialState.levels and ACPIState.levels
arrays:
drivers/gpu/drm/radeon/ni_dpm.c:
1690 table->initialState.levels[0].mclk.vMPLL_AD_FUNC_CNTL =
1691 cpu_to_be32(ni_pi->clock_registers.mpll_ad_func_cntl);
...
1903: table->ACPIState.levels[0].mclk.vMPLL_AD_FUNC_CNTL = cpu_to_be32(mpll_ad_func_cntl);
1904: table->ACPIState.levels[0].mclk.vMPLL_AD_FUNC_CNTL_2 = cpu_to_be32(mpll_ad_func_cntl_2);
because such element cannot exist without previously allocating
any dynamic memory for it (which never actually happens).
That's why struct NISLANDS_SMC_SWSTATE should only be used as type
for object driverState and new struct SISLANDS_SMC_SWSTATE_SINGLE is
created as type for objects initialState, ACPIState and ULVState.
Also, with the change from one-element array to flexible-array member
in commit 434fb1e7444a ("drm/radeon/nislands_smc.h: Replace one-element
array with flexible-array member in struct NISLANDS_SMC_SWSTATE"), the
size of dpmLevels in struct NISLANDS_SMC_STATETABLE should be fixed to
be NISLANDS_MAX_SMC_PERFORMANCE_LEVELS_PER_SWSTATE instead of
NISLANDS_MAX_SMC_PERFORMANCE_LEVELS_PER_SWSTATE - 1.
Bug: https://lore.kernel.org/dri-devel/3eedbe78-1fbd-4763-a7f3-ac5665e76a4a@xenosoft.de/
Fixes: 434fb1e7444a ("drm/radeon/nislands_smc.h: Replace one-element array with flexible-array member in struct NISLANDS_SMC_SWSTATE")
Cc: stable@vger.kernel.org
Reported-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Link: https://lore.kernel.org/dri-devel/9bb5fcbd-daf5-1669-b3e7-b8624b3c36f9@xenosoft.de/
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The new ana_log_size should be used instead of the old one.
Or kernel NULL pointer dereference will happen like below:
[ 38.957849][ T69] BUG: kernel NULL pointer dereference, address: 000000000000003c
[ 38.975550][ T69] #PF: supervisor write access in kernel mode
[ 38.975955][ T69] #PF: error_code(0x0002) - not-present page
[ 38.976905][ T69] PGD 0 P4D 0
[ 38.979388][ T69] Oops: 0002 [#1] SMP NOPTI
[ 38.980488][ T69] CPU: 0 PID: 69 Comm: kworker/0:2 Not tainted 5.12.0+ #54
[ 38.981254][ T69] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014
[ 38.982502][ T69] Workqueue: events nvme_loop_execute_work
[ 38.985219][ T69] RIP: 0010:memcpy_orig+0x68/0x10f
[ 38.986203][ T69] Code: 83 c2 20 eb 44 48 01 d6 48 01 d7 48 83 ea 20 0f 1f 00 48 83 ea 20 4c 8b 46 f8 4c 8b 4e f0 4c 8b 56 e8 4c 8b 5e e0 48 8d 76 e0 <4c> 89 47 f8 4c 89 4f f0 4c 89 57 e8 4c 89 5f e0 48 8d 7f e0 73 d2
[ 38.987677][ T69] RSP: 0018:ffffc900001b7d48 EFLAGS: 00000287
[ 38.987996][ T69] RAX: 0000000000000020 RBX: 0000000000000024 RCX: 0000000000000010
[ 38.988327][ T69] RDX: ffffffffffffffe4 RSI: ffff8881084bc004 RDI: 0000000000000044
[ 38.988620][ T69] RBP: 0000000000000024 R08: 0000000100000000 R09: 0000000000000000
[ 38.988991][ T69] R10: 0000000100000000 R11: 0000000000000001 R12: 0000000000000024
[ 38.989289][ T69] R13: ffff8881084bc000 R14: 0000000000000000 R15: 0000000000000024
[ 38.989845][ T69] FS: 0000000000000000(0000) GS:ffff888237c00000(0000) knlGS:0000000000000000
[ 38.990234][ T69] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 38.990490][ T69] CR2: 000000000000003c CR3: 00000001085b2000 CR4: 00000000000006f0
[ 38.991105][ T69] Call Trace:
[ 38.994157][ T69] sg_copy_buffer+0xb8/0xf0
[ 38.995357][ T69] nvmet_copy_to_sgl+0x48/0x6d
[ 38.995565][ T69] nvmet_execute_get_log_page_ana+0xd4/0x1cb
[ 38.995792][ T69] nvmet_execute_get_log_page+0xc9/0x146
[ 38.995992][ T69] nvme_loop_execute_work+0x3e/0x44
[ 38.996181][ T69] process_one_work+0x1c3/0x3c0
[ 38.996393][ T69] worker_thread+0x44/0x3d0
[ 38.996600][ T69] ? cancel_delayed_work+0x90/0x90
[ 38.996804][ T69] kthread+0xf7/0x130
[ 38.996961][ T69] ? kthread_create_worker_on_cpu+0x70/0x70
[ 38.997171][ T69] ret_from_fork+0x22/0x30
[ 38.997705][ T69] Modules linked in:
[ 38.998741][ T69] CR2: 000000000000003c
[ 39.000104][ T69] ---[ end trace e719927b609d0fa0 ]---
Fixes: 5e1f689913a4 ("nvme-multipath: fix double initialization of ANA state")
Signed-off-by: Hou Pu <houpu.main@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
This loop ends on -1 so the error message will never be printed.
Fixes: 4bcf59a5dea0 ("serial: 8250: 8250_omap: Account for data in flight during DMA teardown")
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YIpd+kOpXKMpEXPf@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This fixes the following checkpatch.pl warnings:
WARNING: Missing a blank line after declarations
WARNING: braces {} are not necessary for any arm of this statement
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/257ffd691b4a062ad017333c9430d69da6dbd29a.1619594713.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use 'hlist_for_each_entry' instead of hand writing it.
This saves a few lines of code.
The comment about warning generated by some gcc version is also removed.
The way 'hlist_for_each_entry' is written should prevent such a warning to
be emitted.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/14024ddeb2b3a8c5b0138b5ba5083f54d00164a9.1619594713.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The variable id being initialized with a value that is never read
and it is being updated later with a new value. The initialization is
redundant and can be removed. Since id is just being used in a for-loop
inside a local scope, move the declaration of id to that scope.
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Addresses-Coverity: ("Unused value")
Link: https://lore.kernel.org/r/20210426101106.9122-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Our SoC's have always had a NS16650A UART core and older SoC's would
have a compatible string of: 'compatible = ""ns16550a"' and use the
8250_of driver. Our newer SoC's have added enhancements to the base
core to add support for DMA and accurate high speed baud rates and use
this newer 8250_bcm7271 driver. The Device Tree node for our enhanced
UARTs has a compatible string of: 'compatible = "brcm,bcm7271-uart",
"ns16550a"''. With both drivers running and the link order setup so
that the 8250_bcm7217 driver is initialized before the 8250_of driver,
we should bind the 8250_bcm7271 driver to the enhanced UART, or for
upstream kernels that don't have the 8250_bcm7271 driver, we bind to
the 8250_of driver.
The problem is that when both the 8250_of and 8250_bcm7271 drivers
were running, occasionally the 8250_of driver would be bound to the
enhanced UART instead of the 8250_bcm7271 driver. This was happening
because we use SCMI based clocks which come up late in initialization
and cause probe DEFER's when the two drivers get their clocks.
Occasionally the SCMI clock would become ready between the 8250_bcm7271
probe and the 8250_of probe and the 8250_of driver would be bound. To
fix this we decided to config only our 8250_bcm7271 driver and added
"ns16665a0" to the compatible string so the driver would work on our
older system.
This commit has of_platform_serial_probe() check specifically for the
"brcm,bcm7271-uart" and whether its companion driver is enabled. If it
is the case, and the clock provider is not ready, we want to make sure
that when the 8250_bcm7271.c driver returns EPROBE_DEFER, we are not
getting the UART registered via 8250_of.c.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jim Quinlan <jim2101024@gmail.com>
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210423183206.3917725-1-f.fainelli@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The variable line being initialized with a value that is never read
and it is being updated later with a new value. The initialization is
redundant and can be removed.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Addresses-Coverity: ("Unused value")
Link: https://lore.kernel.org/r/20210423081317.318352-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Previously this driver's use of devm_ioremap_resource() led to
duplicated calls to __release_region() when unbinding it (one from
serial8250_release_std_resource() and one from devres_release_all()),
the second of which resulted in a warning message:
# echo 1e787000.serial > /sys/bus/platform/drivers/aspeed-vuart/unbind
[33091.774200] Trying to free nonexistent resource <000000001e787000-000000001e78703f>
With this change the driver uses the generic serial8250 code's
UPF_IOREMAP to take care of the register mapping automatically instead
of doing its own devm_ioremap_resource(), thus avoiding the duplicate
__release_region() on unbind.
In doing this we eliminate vuart->regs, since it merely duplicates
vuart->port->port.membase, which we now use for our I/O accesses.
Reported-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Link: https://lore.kernel.org/r/20210510014231.647-4-zev@bewilderbeest.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Previously this had only been initialized if we hit the throttling path
in aspeed_vuart_handle_irq(); moving it to the probe function is a
slight consistency improvement and avoids redundant reinitialization in
the interrupt handler. It also serves as preparation for converting the
driver's I/O accesses to use port->port.membase instead of its own
vuart->regs.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Link: https://lore.kernel.org/r/20210510014231.647-3-zev@bewilderbeest.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is a small prepatory step for changing the way this driver does
its I/O accesses.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Link: https://lore.kernel.org/r/20210510014231.647-2-zev@bewilderbeest.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
With commit 312c004d36ce ("[PATCH] driver core: replace "hotplug" by
"uevent"") already in the tree over a decade, update the name of
FW_ACTION defines to follow semantics, and reflect what the defines are
really meant for, i.e. whether or not generate user space event.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20210425020024.28057-1-shawn.guo@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The value of 'ret' is not used which reported by svace, so just return
instead of break.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Link: https://lore.kernel.org/r/1619484575-26098-1-git-send-email-tiantao6@hisilicon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
SYSRQ doesn't work with DMA. This is because there is no error
indication whether a symbol had a framing error or not. Actually,
this is not completely correct, there is a bit in the data register
which is set in this case, but we'd have to read change the DMA access
to 16 bit and we'd need to post process the data, thus make the DMA
pointless in the first place.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20210512141255.18277-10-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The LPUART can loop the RX and TX signal. Add support for it.
Please note, this was only tested on the 32 bit version of the LPUART.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20210512141255.18277-9-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The LPUART doesn't have the ability to control the RTS or CTS line
manually. Instead it will set it automatically when data is send or
handle it when data is received. Thus drop the wrong code in set_mctrl.
For the 32 bit version this was already done in the commit 2b30efe2e88a
("tty: serial: lpuart: Remove unnecessary code from set_mctrl"). Keep
the 8-bit version in sync and remove it there, too.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20210512141255.18277-8-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
Maximilian Luz
Geert Uytterhoeven
Ondrej Mosnacek
Colin Ian King
Jiri Slaby
Sathishkumar S
Kai-Heng Feng
Likun Gao
David Ward
Gustavo A. R. Silva
Hou Pu
Dan Carpenter
Christophe JAILLET
Jim Quinlan
Zev Weiss
Shawn Guo
Tian Tao
Michael Walle