| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Since we added the dpaa2_switch_acl_entry_add() function in the previous
patches to hide all the details of actually adding the ACL entry by
issuing a firmware command, let's use it also for adding a CPU trap for
the STP frames.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support TC_SETUP_CLSMATCHALL by using the same ACL table entries
framework as for tc flower. Adding a matchall rule is done by installing
an entry which has a mask of all zeroes, thus matching on any packet.
This can be used as a catch-all type of rule if used correctly, ie the
priority of the matchall filter should be kept as the lowest one in the
entire filter block.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for tc flower hardware offload on the ingress
path. Shared filter blocks are supported by sharing a single ACL table
between multiple ports.
The following flow keys are supported:
- Ethernet: dst_mac/src_mac
- IPv4: dst_ip/src_ip/ip_proto/tos
- VLAN: vlan_id/vlan_prio/vlan_tpid/vlan_dei
- L4: dst_port/src_port
As per flow actions, the following are supported:
- drop
- mirred egress redirect
- trap
Each ACL entry (filter) can be setup with only one of the listed
actions.
A sorted single linked list is used to keep the ACL entries by their
order of priority. When adding a new filter, this enables us to quickly
ascertain if the new entry has the highest priority of the entire block
or if we should make some space in the ACL table by increasing the
priority of the filters already in the table.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change the default ACL trap rule for STP frames to have the highest
priority.
In the same ACL table will reside both default rules added by the driver
for its internal use as well as rules added with tc flower. In this
case, the default rules such as the STP one that we already have should
have the highest priority.
Also, remove the check for a full ACL table since we already know that
it's sized so that we don't hit this case. The last thing changes is
that default trap filters will not be counted in the acl_tbl's num_rules
variable since their number doesn't change.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce a new structure - dpaa2_switch_acl_tbl - to hold all data
related to an ACL table: number of rules added, ACL table id, etc.
This will be used more in the next patches when adding support for
sharing an ACL table between ports.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The copy_to_user() function returns the number of bytes that it wasn't
able to copy. We want to return -EFAULT to the user.
Fixes: fee6efce565d ("ionic: add hw timestamp support files")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We add the support of XDP ZC TX submission and cleaning into
stmmac_tx_clean(). The function is made to clean as many TX complete
frames as possible, i.e. limit by priv->dma_tx_size instead of NAPI
budget. For TX ring that is associated with XSK pool, the function
stmmac_xdp_xmit_zc() is introduced to TX frame buffers from XSK pool by
using xsk_tx_peek_desc(). To make stmmac_tx_clean() support the cleaning
of XSK TX frames, STMMAC_TXBUF_T_XSK_TX TX buffer type is introduced.
As stmmac_tx_clean() uses the return value to cue whether NAPI function
should continue to poll, we augment the caller of stmmac_tx_clean() to
pass NAPI budget instead of priv->dma_tx_size through 'budget' input and
made stmmac_tx_clean() to always clean up-to the TX ring size instead.
This allows us to use the return boolean status of stmmac_xdp_xmit_zc()
to decide if XSK TX work is done or not: If true, set 'xmits' to return
'budget - 1' so that NAPI poll may exit. Else, set 'xmits' to return
'budget' to make NAPI poll continue to poll since XSK TX work is not
done. Finally, at the end of stmmac_tx_clean(), the function now take
a maximum value between 'count' and 'xmits' so that status from both
TX cleaning and XSK TX (only for XDP ZC) is considered.
This patch adds a new NAPI poll called stmmac_napi_poll_rxtx() that is
meant to be enabled/disabled for RX and TX ring that are bound to XSK
pool. This NAPI poll function starts with cleaning TX ring, then submits
XSK TX frames to TX ring before proceed to perform RX operations, i.e.
, receiving RX frames and replenishing RX ring with RX free buffers
obtained from XSK pool. Therefore, during XSK RX and TX setup, the driver
enables stmmac_napi_poll_rxtx() for RX and TX operations, then during
XSK RX and TX pool tear-down, the driver reenables the exisiting
independent NAPI poll functions accordingly: stmmac_napi_poll_rx() and
stmmac_napi_poll_tx().
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the support for receiving packet via AF_XDP zero-copy
mechanism.
XDP ZC uses 1:1 mapping of XDP buffer to receive packet, therefore the
use of split header is not used currently. The 'xdp_buff' is declared as
union together with a struct that contains 'page', 'addr' and
'page_offset' that are associated with primary buffer.
RX buffers are now allocated either via page_pool or xsk pool. For RX
buffers from xsk_pool they are allocated and deallocated using below
functions:
* stmmac_alloc_rx_buffers_zc(struct stmmac_priv *priv, u32 queue)
* dma_free_rx_xskbufs(struct stmmac_priv *priv, u32 queue)
With above functions now available, we then extend the following driver
functions to support XDP ZC:
* stmmac_reinit_rx_buffers()
* __init_dma_rx_desc_rings()
* init_dma_rx_desc_rings()
* __free_dma_rx_desc_resources()
Note: stmmac_alloc_rx_buffers_zc() may return -ENOMEM due to RX XDP
buffer pool is not allocated (e.g. samples/bpf/xdpsock TX-only). But,
it is still ok to let TX XDP ZC to continue, therefore, the -ENOMEM
is silently ignored to let the driver succcessfully transition to XDP
ZC mode for the said RX and TX queue.
As XDP ZC buffer size is different, the DMA buffer size is required
to be reprogrammed accordingly for RX DMA/Queue that is populated with
XDP buffer from XSK pool.
Next, to add or remove per-queue XSK pool, stmmac_xdp_setup_pool()
will call stmmac_xdp_enable_pool() or stmmac_xdp_disable_pool()
that in-turn coordinates the tearing down and setting up RX ring via
RX buffers and descriptors removal and reallocation through
stmmac_disable_rx_queue() and stmmac_enable_rx_queue(). In addition,
stmmac_xsk_wakeup() is added to initiate XDP RX buffer replenishing
by signalling user application to add available XDP frames back to
FILL queue.
For RX processing using XDP zero-copy buffer, stmmac_rx_zc() is
introduced which is implemented with the assumption that RX split
header is disabled. For XDP verdict is XDP_PASS, the XDP buffer is
copied into a sk_buff allocated through stmmac_construct_skb_zc()
and sent to Linux network GRO inside stmmac_dispatch_skb_zc(). Free RX
buffers are then replenished using stmmac_rx_refill_zc()
v2: introduce __stmmac_disable_all_queues() to contain the original code
that does napi_disable() and then make stmmac_setup_tc_block_cb()
to use it. Move synchronize_rcu() into stmmac_disable_all_queues()
that eventually calls __stmmac_disable_all_queues(). Then,
make both stmmac_release() and stmmac_suspend() to use
stmmac_disable_all_queues(). Thanks David Miller for spotting the
synchronize_rcu() issue in v1 patch.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prepare stmmac_xdp_run_prog() for AF_XDP zero-copy support which will be
added by upcoming patches by splitting out the XDP verdict processing
into __stmmac_xdp_run_prog() and it callable for XDP ZC path which does
not need to verify bpf_prog is not NULL.
The stmmac_xdp_run_prog() is used for regular XDP Rx path which requires
bpf_prog to be verified.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Below functions are made to be per-queue in preparation of XDP ZC:
__init_dma_rx_desc_rings(struct stmmac_priv *priv, u32 queue, gfp_t flags)
__init_dma_tx_desc_rings(struct stmmac_priv *priv, u32 queue)
The original functions below are stay maintained for all queue usage:
init_dma_rx_desc_rings(struct net_device *dev, gfp_t flags)
init_dma_tx_desc_rings(struct net_device *dev)
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The per-queue RX buffer allocation in stmmac_reinit_rx_buffers() can be
made to use stmmac_alloc_rx_buffers() by merging the page_pool alloc
checks for "buf->page" and "buf->sec_page" in stmmac_init_rx_buffers().
This is in preparation for XSK pool allocation later.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rearrange RX buffer page_pool recycling logics into dma_recycle_rx_skbufs,
so that we prepare stmmac_reinit_rx_buffers() for XSK pool expansion.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch restructures the per RX queue buffer allocation from page_pool
to stmmac_alloc_rx_buffers().
We also rearrange dma_free_rx_skbufs() so that it can be used in
init_dma_rx_desc_rings() during freeing of RX buffer in the event of
page_pool allocation failure to replace the more efficient method earlier.
The replacement is needed to make the RX buffer alloc and free method
scalable to XDP ZC xsk_pool alloc and free later.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the SM8350 SoC, which includes IPA version 4.9.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All the uses of HWTSTAMP_FILTER_* values need to be
bit shifters, not straight values.
v2: fixed subject and added Cc Dan and SoB Allen
Fixes: f8ba81da73fc ("ionic: add ethtool support for PTP")
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: Allen Hubbe <allenbh@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The reset process for ibmvnic commonly takes multiple seconds, clearly
making it inappropriate for schedule_work/system_wq. The reason to make
this change is that ibmvnic's use of the default system-wide workqueue
for a relatively long-running work item can negatively affect other
workqueue users. So, queue the relatively slow reset job to the
system_long_wq.
Suggested-by: Nathan Lynch <nathanl@linux.ibm.com>
Signed-off-by: Lijun Pan <lijunp213@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Marc Kleine-Budde says:
====================
pull-request: can-next 2021-04-13
this is a pull request of 14 patches for net-next/master.
The first patch is by Yoshihiro Shimoda and updates the DT bindings
for the rcar_can driver.
Vincent Mailhol contributes 3 patches that add support for several
ETAS USB CAN adapters.
The final 10 patches are by me and clean up the peak_usb CAN driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the following versioncheck warning:
./drivers/net/wireless/rsi/rsi_91x_ps.c: 19 linux/version.h not needed.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
in st_nci_spi_write function, first assign a value to a variable then
goto exit label. return statement just follow the label and exit label
just used once, so we should directly return and remove exit label.
Signed-off-by: wengjianfeng <wengjianfeng@yulong.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is more correct to use dev_kfree_skb_irq when packets are dropped,
and to use dev_consume_skb_irq when packets are consumed.
Fixes: 0d973388185d ("ibmvnic: Introduce xmit_more support using batched subCRQ hcalls")
Suggested-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: Lijun Pan <lijunp213@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current implementation relies on H_IOCTL call to issue a
H_SESSION_ERR_DETECTED command to let the hypervisor to send a failover
signal. However, it may not work if there is no backup device or if
the vnic is already in error state,
e.g., "ibmvnic 30000003 env3: rx buffer returned with rc 6".
Add a last resort, that is to schedule a failover reset via CRQ command.
Signed-off-by: Lijun Pan <lijunp213@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
msm-next from Rob:
* Big DSI phy/pll cleanup. Includes some clk patches, acked by
maintainer
* Initial support for sc7280
* compatibles fixes for sm8150/sm8250
* cleanups for all dpu gens to use same bandwidth scaling paths (\o/)
* various shrinker path lock contention optimizations
* unpin/swap support for GEM objects (disabled by default, enable with
msm.enable_eviction=1 .. due to various combinations of iommu drivers
with older gens I want to get more testing on hw I don't have in front
of me before enabling by default)
* The usual assortment of misc fixes and cleanups
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGvL=4aw15qoY8fbKG9FCgnx8Y-dCtf7xiFwTQSHopwSQg@mail.gmail.com
|
|
of_get_mac_address() already supports fetching the MAC address by an
nvmem provider. But until now, it was just working for platform devices.
Esp. it was not working for DSA ports and PCI devices. It gets more
common that PCI devices have a device tree binding since SoCs contain
integrated root complexes.
Use the nvmem of_* binding to fetch the nvmem cells by a struct
device_node. We still have to try to read the cell by device first
because there might be a nvmem_cell_lookup associated with that device.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
of_get_mac_address() returns a "const void*" pointer to a MAC address.
Lately, support to fetch the MAC address by an NVMEM provider was added.
But this will only work with platform devices. It will not work with
PCI devices (e.g. of an integrated root complex) and esp. not with DSA
ports.
There is an of_* variant of the nvmem binding which works without
devices. The returned data of a nvmem_cell_read() has to be freed after
use. On the other hand the return of_get_mac_address() points to some
static data without a lifetime. The trick for now, was to allocate a
device resource managed buffer which is then returned. This will only
work if we have an actual device.
Change it, so that the caller of of_get_mac_address() has to supply a
buffer where the MAC address is written to. Unfortunately, this will
touch all drivers which use the of_get_mac_address().
Usually the code looks like:
const char *addr;
addr = of_get_mac_address(np);
if (!IS_ERR(addr))
ether_addr_copy(ndev->dev_addr, addr);
This can then be simply rewritten as:
of_get_mac_address(np, ndev->dev_addr);
Sometimes is_valid_ether_addr() is used to test the MAC address.
of_get_mac_address() already makes sure, it just returns a valid MAC
address. Thus we can just test its return code. But we have to be
careful if there are still other sources for the MAC address before the
of_get_mac_address(). In this case we have to keep the
is_valid_ether_addr() call.
The following coccinelle patch was used to convert common cases to the
new style. Afterwards, I've manually gone over the drivers and fixed the
return code variable: either used a new one or if one was already
available use that. Mansour Moufid, thanks for that coccinelle patch!
<spml>
@a@
identifier x;
expression y, z;
@@
- x = of_get_mac_address(y);
+ x = of_get_mac_address(y, z);
<...
- ether_addr_copy(z, x);
...>
@@
identifier a.x;
@@
- if (<+... x ...+>) {}
@@
identifier a.x;
@@
if (<+... x ...+>) {
...
}
- else {}
@@
identifier a.x;
expression e;
@@
- if (<+... x ...+>@e)
- {}
- else
+ if (!(e))
{...}
@@
expression x, y, z;
@@
- x = of_get_mac_address(y, z);
+ of_get_mac_address(y, z);
... when != x
</spml>
All drivers, except drivers/net/ethernet/aeroflex/greth.c, were
compile-time tested.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds EEE support.
Signed-off-by: René van Dorst <opensource@vdorst.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
msm-next pull request has a baseline with stuff from -fixes, roll
forward first.
Some simple conflicts in amdgpu, ttm and one in i915 where git gets
confused and tries to add the same function twice.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Kalle Valo says:
====================
wireless-drivers-next patches for v5.13
First set of patches for v5.13. I have been offline for a couple of
and I have a smaller pull request this time. The next one will be
bigger. Nothing really special standing out.
ath11k
* add initial support for QCN9074, but not enabled yet due to firmware problems
* enable radar detection for 160MHz secondary segment
* handle beacon misses in station mode
rtw88
* 8822c: support firmware crash dump
mt7601u
* enable TDLS support
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull MTD fix from Richard Weinberger:
"Fix WAITRDY break condition and timeout in mtk nand driver"
* tag 'fixes-for-5.12-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: rawnand: mtk: Fix WAITRDY break condition and timeout
|
|
In case of error, the function devm_ioremap() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should
be replaced with NULL test.
Fixes: 0af65b9b915e ("remoteproc: qcom: wcss: Add non pas wcss Q6 support for QCS404")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20210319094100.4185044-1-weiyongjun1@huawei.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The PRU firmware interrupt mappings are configured and unconfigured in
.start() and .stop() callbacks respectively using the variables 'evt_count'
and a 'mapped_irq' pointer. These variables are modified only during these
callbacks but are not re-initialized/reset properly during unwind or
failure paths. These stale values caused a kernel crash while stopping a
PRU remoteproc running a different firmware with no events on a subsequent
run after a previous run that was running a firmware with events.
Fix this crash by ensuring that the evt_count is 0 and the mapped_irq
pointer is set to NULL in pru_dispose_irq_mapping(). Also, reset these
variables properly during any failures in the .start() callback. While
at this, the pru_dispose_irq_mapping() callsites are all made to look
the same, moving any conditional logic to inside the function.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Fixes: c75c9fdac66e ("remoteproc: pru: Add support for PRU specific interrupt configuration")
Reported-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20210407155641.5501-4-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The irq_create_fwspec_mapping() returns a proper virq value on success
and 0 upon any failure. The pru_handle_intrmap() treats this as an error
and disposes all firmware event mappings correctly, but is returning
this incorrect value as is, letting the pru_rproc_start() interpret it
as a success and boot the PRU.
Fix this by returning an error value back upon any such failure. While
at this, revise the error trace to print some meaningful info about the
failed event.
Fixes: c75c9fdac66e ("remoteproc: pru: Add support for PRU specific interrupt configuration")
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20210407155641.5501-3-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The PRU firmware interrupt mapping logic in pru_handle_intrmap() uses
of_irq_find_parent() with PRU device node to get a handle to the PRUSS
Interrupt Controller at present. This logic however requires that the
PRU nodes always define a interrupt-parent property. This property is
neither a required/defined property as per the PRU remoteproc binding,
nor is relevant from a DT node point of view without any associated
interrupts. The current logic finds a wrong interrupt controller and
fails to perform proper mapping without any interrupt-parent property
in the PRU nodes.
Fix this logic to always find and use the sibling interrupt controller.
Also, while at this, fix the acquired interrupt controller device node
reference properly.
Fixes: c75c9fdac66e ("remoteproc: pru: Add support for PRU specific interrupt configuration")
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20210407155641.5501-2-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
A for-loop is using a u8 loop counter that is being compared to
a u32 cmp_dcbcfg->numapp to check for the end of the loop. If
cmp_dcbcfg->numapp is larger than 255 then the counter j will wrap
around to zero and hence an infinite loop occurs. Fix this by making
counter j the same type as cmp_dcbcfg->numapp.
Addresses-Coverity: ("Infinite loop")
Fixes: aeac8ce864d9 ("ice: Recognize 860 as iSCSI port in CEE mode")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
pci_disable_device() called in __ixgbe_shutdown() decreases
dev->enable_cnt by 1. pci_enable_device_mem() which increases
dev->enable_cnt by 1, was removed from ixgbe_resume() in commit
6f82b2558735 ("ixgbe: use generic power management"). This caused
unbalanced increase/decrease. So add pci_enable_device_mem() back.
Fix the following call trace.
ixgbe 0000:17:00.1: disabling already-disabled device
Call Trace:
__ixgbe_shutdown+0x10a/0x1e0 [ixgbe]
ixgbe_suspend+0x32/0x70 [ixgbe]
pci_pm_suspend+0x87/0x160
? pci_pm_freeze+0xd0/0xd0
dpm_run_callback+0x42/0x170
__device_suspend+0x114/0x460
async_suspend+0x1f/0xa0
async_run_entry_fn+0x3c/0xf0
process_one_work+0x1dd/0x410
worker_thread+0x34/0x3f0
? cancel_delayed_work+0x90/0x90
kthread+0x14c/0x170
? kthread_park+0x90/0x90
ret_from_fork+0x1f/0x30
Fixes: 6f82b2558735 ("ixgbe: use generic power management")
Signed-off-by: Yongxin Liu <yongxin.liu@windriver.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The ixgbe driver currently generates a NULL pointer dereference when
performing the ethtool loopback test. This is due to the fact that there
isn't a q_vector associated with the test ring when it is setup as
interrupts are not normally added to the test rings.
To address this I have added code that will check for a q_vector before
returning a napi_id value. If a q_vector is not present it will return a
value of 0.
Fixes: b02e5a0ebb17 ("xsk: Propagate napi_id to XDP socket Rx path")
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
All other users of the dummy netdevice embed the netdev in other
structures:
init_dummy_netdev(&mal->dummy_dev);
init_dummy_netdev(ð->dummy_dev);
init_dummy_netdev(&ar->napi_dev);
init_dummy_netdev(&irq_grp->napi_ndev);
init_dummy_netdev(&wil->napi_ndev);
init_dummy_netdev(&trans_pcie->napi_dev);
init_dummy_netdev(&dev->napi_dev);
init_dummy_netdev(&bus->mux_dev);
The AIP and VNIC implementation turns that model inside out and used a
kfree() to free what appears to be a netdev struct when in reality, it is
a struct that enbodies the rx state as well as the dummy netdev used to
support napi_poll across disparate receive contexts. The relationship is
infered by the odd allocation:
const int netdev_size = sizeof(*dd->dummy_netdev) +
sizeof(struct hfi1_netdev_priv);
<snip>
dd->dummy_netdev = kcalloc_node(1, netdev_size, GFP_KERNEL, dd->node);
Correct the issue by:
- Correctly naming the alloc and free functions
- Renaming hfi1_netdev_priv to hfi1_netdev_rx
- Replacing dd dummy_netdev with a netdev_rx pointer
- Embedding the net_device in hfi1_netdev_rx
- Moving the init_dummy_netdev to the alloc routine
- Adjusting wrappers to fit the new model
Fixes: 6991abcb993c ("IB/hfi1: Add functions to receive accelerated ipoib packets")
Link: https://lore.kernel.org/r/1617026056-50483-11-git-send-email-dennis.dalessandro@cornelisnetworks.com
Reviewed-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
Signed-off-by: Marc Zyngier <maz@kernel.org>
|
|
Now that the xr_serial got support for other models, add their USB IDs
as well.
The Maxlinear/Exar USB UARTs can be used in either ACM mode using the
cdc-acm driver or in "custom driver" mode in which further features such
as hardware and software flow control, GPIO control and in-band
line-status reporting are available.
In ACM mode the device always enables RTS/CTS flow control, something
which could prevent transmission in case the CTS input isn't wired up
correctly.
Ensure that cdc_acm will not bind to these devices if the custom
USB-serial driver is enabled.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/5155887a764cbc11f8da0217fe08a24a77d120b4.1616571453.git.mchehab+huawei@kernel.org
[ johan: rewrite commit message, clean up entries ]
Cc: Oliver Neukum <oneukum@suse.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Add another copyright notice for the work done in 2021.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Reset the transmit and receive FIFOs before enabling the UARTs as part
of open() in order to flush any stale data.
Note that the XR21V141X needs a type-specific implementation due to its
UART Manager registers.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
The XR22801, XR22802 and XR22804 are compound devices with an embedded
hub and up to seven downstream USB devices including one, two or four
UARTs respectively.
The UART function is similar to XR21B142X but most registers are offset
by 0x40, the register requests are different and are directed at the
device rather than interface, and 5 and 6-bit words are not supported.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
The single-port XR21B1411 is similar to the XR21B142X type but uses
12-bit registers and 16-bit register addresses, the register requests
are different and are directed at the device rather than interface, and
5 and 6-bit words are not supported.
The register layout is very similar to XR21B142X except that most
registers are offset by 0xc00 (corresponding to a channel index of 12 in
the MSB of wIndex). As the device is single-port so that the derived
channel index is 0, the current register accessors can be reused after
simply changing the address width.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
The XR21B1421, XR21B1422 and XR21B1424 are the one-, two- and four-port
models of a second XR21B142X type of the Maxlinear/Exar USB UARTs.
The XR21B142X type differs from XR21V141X in several ways, including:
- register layout
- register width (16-bit instead of 8-bit)
- vendor register requests
- UART enable/disable sequence
- custom-driver mode flag
- three additional GPIOs (9 instead of 6)
As for XR21V141X, the XR21B142X vendor requests encode the channel index
in the MSB of wIndex, but it lacks the UART Manager registers which
have been replaced by regular UART registers. The new type also uses the
interface number of the control interface (0, 2, 4, 6) as channel index
instead of the channel number (0, 1, 2, 3).
The XR21B142X lacks the divisor and format registers used by XR21V141X
and instead uses the CDC SET_LINE_CONTROL request to configure the line
settings.
Note that the currently supported XR21V141X type lacks the custom-driver
mode flag that prevents the device from entering CDC-ACM mode when a CDC
requests is received. This specifically means that the SET_LINE_CONTROL
request cannot be used with XR21V141X even though it is otherwise
supported.
The UART enable sequence for XR21B142X does not involve explicitly
enabling the FIFOs, but according to datasheet the UART must be disabled
when writing any register but GPIO_SET, GPIO_CLEAR, TX_BREAK and
ERROR_STATUS.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
There are at least four types of Maxlinear/Exar USB UARTs which differ
in various ways such as in their register layouts:
XR21V141X
XR21B142X
XR21B1411
XR22804
It is not clear whether the device type can be inferred from the
descriptors so encode it in the device-id table for now.
Add a type structure that can be used to abstract the register layout
and other features, and use it when accessing the XR21V141X UART
registers that are shared by all types.
Note that the currently supported XR21V141X type is the only type that
has a set of UART Manager registers and that these will need to be
handled specifically.
Similarly, XR21V141X is the only type which has the divisor registers
and that needs to use the format register when configuring the line
settings.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
In preparation for adding support for further types, drop the type
prefix from defines that are not specific to XR21V141X.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
There's no need to configure the pins on every open and judging from the
vendor driver and datasheet it can be done before enabling the UART.
Move pin configuration from open() to port probe and make sure to
deassert DTR and RTS after configuring all pins as GPIO.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Rename the GPIO-pin defines so that they reflect how they are used.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Rename the GPIO mode defines so that they reflect the datasheet and how
they are used.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Add support for the two- and four-port variants of XR21V1410.
Use the interface number of each control interface (e.g. 0, 2, 4, 6) to
derive the zero-based channel index:
XR21V1410 0
XR21V1412 0, 1
XR21V1414 0, 1, 2, 3
Note that the UART registers reside in separate blocks per channel,
while the UART Manager functionality is implemented using per-channel
registers.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Remove the random white space from the CSIZE switch.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
Ioana Ciornei
Dan Carpenter
Ong Boon Leong
Alex Elder
Shannon Nelson
Lijun Pan
David S. Miller
Yang Li
wengjianfeng
Daniel Vetter
Michael Walle
René van Dorst
Linus Torvalds
Wei Yongjun
Suman Anna
Colin Ian King
Yongxin Liu
Alexander Duyck
Mike Marciniszyn
Marc Zyngier
Mauro Carvalho Chehab
Johan Hovold