| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The datasheet says that VDD12 must be enabled and at full voltage before
VDD33 is enabled.
Reorder the bulk regulator supply names so that VDD12 is enabled before
VDD33. Any enable ramp delays should be handled by setting proper
constraints on the regulators.
Fixes: bc1aee7fc8f0 ("drm/bridge: Add I2C based driver for ps8640 bridge")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220721092258.3397461-1-wenst@chromium.org
|
|
Change the of_device_get_match_data() cast to (uintptr_t)
to silence the following clang warning:
drivers/dma/imx-dma.c:1048:20: warning: cast to smaller integer type 'enum imx_dma_type' from 'const void *' [-Wvoid-pointer-to-enum-cast]
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 0ab785c894e6 ("dmaengine: imx-dma: Remove unused .id_table")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Link: https://lore.kernel.org/r/20220706111327.940764-1-festevam@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
If the channel has no descriptor and the interrupt is raised then the
kernel will OOPS. Check the result of vchan_next_desc() in the handler
axi_chan_block_xfer_complete() to avoid the error happening.
Signed-off-by: Ben Dooks <ben.dooks@sifive.com>
Link: https://lore.kernel.org/r/20220708170153.269991-4-ben.dooks@sifive.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
During debugging we have seen an issue where axi_chan_dump_lli()
is passed a NULL LLI pointer which ends up causing an OOPS due
to trying to get fields from it. Simply print NULL LLI and exit
to avoid this.
Signed-off-by: Ben Dooks <ben.dooks@sifive.com>
Link: https://lore.kernel.org/r/20220708170153.269991-3-ben.dooks@sifive.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Prox-out events may not be reliably sent by some AES firmware. This can
cause problems for users, particularly due to arbitration logic disabling
touch input while the pen is in prox.
This commit adds a timer which is reset every time a new prox event is
received. When the timer expires we check to see if the pen is still in
prox and force it out if necessary. This is patterend off of the same
solution used by 'hid-letsketch' driver which has a similar problem.
Link: https://github.com/linuxwacom/input-wacom/issues/310
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
joycon_dpad_inputs_jc[] is unterminated. This may result in odd warnings
such as
input: input_set_capability: invalid code 3077588140 for type 1
or in kernel crashes in nintendo_hid_probe(). Terminate the array to fix
the problem.
Fixes: 2af16c1f846bd ("HID: nintendo: add nintendo switch controller driver")
Cc: Daniel J. Ogorchock <djogorchock@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The double `with' is duplicated in line 769, remove one.
Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Newer AMD SOCs use SFH1.1 memory access with new PCI-id. Hence add new
sfh1_1 sub directory to implement SFH1.1 functionality by defining new
PCI id, interface functions, descriptor functions and handlers which
invokes sfh1.1.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Interrupt handling can be used in multiple files to support all
AMD SOCs. Hence move interrupt handling to common interface.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
amd_sfh_work can be used in multiple files to support all AMD SOCs.
Hence move amd_sfh_work to common interface.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Move global functions declared from header files and make them as static
functions wherever applicable.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Add remove operation as part of amd_mp2_ops structure to support all
AMD SOCs and use wherever applicable.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Add PM operations as part of amd_mp2_ops structure to support all
AMD SOCs and use wherever applicable.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Add dynamic descriptor operations as part of amd_mp2_ops structure to
support all AMD SOCs and use wherever applicable.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
request_list variable can be used in multiple files to support all
AMD SOCs. Hence move request_list variable to client data.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
request_list structure can be used in multiple files to support all
AMD SOCs. Hence move request_list structure to header file.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Introduce common macros and structures to support multiple generations
of AMD SOCs, move them to amd_sfh_common.h.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
On removal of hid device during SFH set report may cause NULL pointer
exception. Hence add NULL check for hid device before accessing.
Fixes: 4b2c53d93a4b ("SFH:Transport Driver to add support of AMD Sensor Fusion Hub (SFH)")
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Commit bebcc522fbee ("HID: core: for input reports, process the usages by
priority list") split the iteration into two distinct loops in
hid_process_report().
After this change, the variable field is only used while iterating in the
second loop and the assignment of values to this variable in the first loop
is simply not needed.
Remove the unneeded assignment during retrieval. No functional change and
no change in the resulting object code.
This was discovered as a dead store with clang-analyzer.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Reviewed-by: Tom Rix <trix@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This improves performance and stability of
DL-3xxx/DL-5xxx/DL-6xxx device series.
Specifically prevents device from temporary network dropouts when
playing video from the web and network traffic going through is high.
Signed-off-by: Dominik Czerwik <dominik.czerwik@synaptics.com>
Signed-off-by: Łukasz Spintzyk <lukasz.spintzyk@synaptics.com>
Link: https://lore.kernel.org/r/20220720060518.541-1-lukasz.spintzyk@synaptics.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
On failure, these functions return error pointer, not NULL.
Signed-off-by: Liu Zixian <liuzixian4@huawei.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220718015357.1722-1-liuzixian4@huawei.com
|
|
there is an unexpected word "the" in the comments that need to be dropped
file: drivers/hid/intel-ish-hid/ishtp-hid-client.c
line: 331
* @device: Pointer to the the ishtp client device for which this message
changed to
* @device: Pointer to the ishtp client device for which this message
Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Smatch Warning:
drivers/hid/hid-mcp2221.c:388 mcp_smbus_write() error: __memcpy()
'&mcp->txbuf[5]' too small (59 vs 255)
drivers/hid/hid-mcp2221.c:388 mcp_smbus_write() error: __memcpy() 'buf'
too small (34 vs 255)
The 'len' variable can take a value between 0-255 as it can come from
data->block[0] and it is user data. So add an bound check to prevent a
buffer overflow in memcpy().
Fixes: 67a95c21463d ("HID: mcp2221: add usb to i2c-smbus host bridge")
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Add default value for `msg->result` so that it won't be garbage bytes
when the mock list is empty.
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Link: https://lore.kernel.org/r/20220720044754.4026295-3-tzungbi@kernel.org
|
|
Merge CROS_KUNIT and CROS_EC_PROTO_KUNIT_TEST so that when they're built
as modules cros_kunit_util doesn't need to export the symbols.
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Link: https://lore.kernel.org/r/20220720044754.4026295-2-tzungbi@kernel.org
|
|
Fix the double `wait' typo in comment.
Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220716040520.31676-1-wangborong@cdjrlc.com
|
|
The semicolon after the `}' is unneeded.
Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
[Removed line mention when pushing]
Link: https://patchwork.freedesktop.org/patch/msgid/20220716184439.72056-1-wangborong@cdjrlc.com
|
|
There is a spelling mistake (writeable) in function rxe_check_bind_mw.
Fix it.
Signed-off-by: Zhang Jiaming <jiaming@nfschina.com>
Reviewed-by: Bob Pearson <rpearsonhpe@gmail.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
Reduce the clutter in the main IPA source directory by creating a
new "data" subdirectory, and locating all of the configuration data
files in there.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Create a variable in the Makefile listing the IPA versions supported
by the driver. Use that to create the list of configuration data
object files used (rather than listing them all individually).
Add a SPDX license comment.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since commit 8797972afff3d ("net: ipa: remove command info pool"),
we don't allocate "command info" entries for command channel
transactions. Fix a comment that seems to suggest we still do.
(Even before that commit, the comment was out of place.)
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When the IPA driver has completed its initialization and setup
stages, it emits a brief message to the log. Add a small message
that reports when it has been removed.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In gsi_trans_free(), there's no point in ipa_gsi_trans_release() if
a transaction is unused. No used TREs means no IPA layer resources
to clean up. So only call ipa_gsi_trans_release() if at least one
TRE was used.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The transaction map is really associated with the transaction pool;
move its definition earlier in the gsi_trans_info structure.
Rearrange initialization in gsi_channel_trans_init() so it
sets the tre_avail value first, then initializes the transaction
pool, and finally allocating the transaction map.
Update comments.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We currently put a transaction on the pending list when it has
been committed. But until the channel's doorbell rings, these
transactions aren't actually "owned" by the hardware yet.
Add a new "committed" state (and list), to represent transactions
that have been committed but not yet sent to hardware. Define
"pending" to mean committed transactions that have been sent
to hardware but have not yet completed.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Create a new attribute group meant to provide a single place that
defines endpoint IDs that might be needed by user space. Not all
defined endpoints are presented, and only those that are defined
will be made visible.
The new attributes use "extended" device attributes to hold endpoint
IDs, which is a little more compact and efficient. Reimplement the
existing modem endpoint ID attribute files using common code.
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20220719191639.373249-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It's repeated with line 1793-1795, and there isn't any other
handling for it. So remove it.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Link: https://lore.kernel.org/r/20220719142424.4528-1-shenjian15@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
amd-drm-fixes-5.19-2022-07-20:
amdgpu:
- Drop redundant buffer cleanup that can lead to a segfault
- Add a bo_list mutex to avoid possible list corruption in CS
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220720210917.6202-1-alexander.deucher@amd.com
|
|
Saeed Mahameed says:
====================
mlx5-updates-2022-07-17
1) Add resiliency for lost completions for PTP TX port timestamp
2) Report Header-data split state via ethtool
3) Decouple HTB code from main regular TX code
* tag 'mlx5-updates-2022-07-17' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5: CT: Remove warning of ignore_flow_level support for non PF
net/mlx5e: Add resiliency for PTP TX port timestamp
net/mlx5: Expose ts_cqe_metadata_size2wqe_counter
net/mlx5e: HTB, move htb functions to a new file
net/mlx5e: HTB, change functions name to follow convention
net/mlx5e: HTB, remove priv from htb function calls
net/mlx5e: HTB, hide and dynamically allocate mlx5e_htb structure
net/mlx5e: HTB, move stats and max_sqs to priv
net/mlx5e: HTB, move section comment to the right place
net/mlx5e: HTB, move ids to selq_params struct
net/mlx5e: HTB, reduce visibility of htb functions
net/mlx5e: Fix mqprio_rl handling on devlink reload
net/mlx5e: Report header-data split state through ethtool
====================
Link: https://lore.kernel.org/r/20220719203529.51151-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
dpu_encoder_helper_phys_cleanup() was not populating neither
wb or intf to the intf_cfg before calling the reset_intf_cfg().
This causes the reset of the active bits of wb/intf to be
skipped which is incorrect.
Fix this by populating the relevant wb or intf indices correctly.
Fixes: ae4d721ce100 ("drm/msm/dpu: add an API to reset the encoder related hw blocks")
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Tested-by: Jessica Zhang <quic_jesszhan@quicinc.com> # Trogdor (SC8170)
Patchwork: https://patchwork.freedesktop.org/patch/494298/
Link: https://lore.kernel.org/r/1657912468-17254-1-git-send-email-quic_abhinavk@quicinc.com
|
|
A bunch of code was copy/pasted using pr_err as the default way to
report errors. However, drm_err is significantly more useful in
identifying where the error came from. So update the code to use that
instead.
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220715004028.2126239-1-John.C.Harrison@Intel.com
|
|
Add panel identification entry for the AUO B120XAN01.0 (product ID:
0x1062) panel.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220720191158.1590833-1-nfraprado@collabora.com
|
|
Add panel identification entry for the IVO R140NWF5 RH (product ID:
0x057d) panel.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220719203857.1488831-2-nfraprado@collabora.com
|
|
Protect the struct amdgpu_bo_list with a mutex. This is used during command
submission in order to avoid buffer object corruption as recorded in
the link below.
v2 (chk): Keep the mutex looked for the whole CS to avoid using the
list from multiple CS threads at the same time.
Suggested-by: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <Alexander.Deucher@amd.com>
Cc: Andrey Grodzovsky <Andrey.Grodzovsky@amd.com>
Cc: Vitaly Prosyak <Vitaly.Prosyak@amd.com>
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2048
Signed-off-by: Luben Tuikov <luben.tuikov@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Tested-by: Luben Tuikov <luben.tuikov@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
[Why]
The amdgpu_dm file contains most of the code that works as an interface
between DRM API and DC. As a result, this file becomes very large since
it comprises multiple abstractions such as plane manipulation.
[How]
This commit extracts the plane code to its specific file named
amdgpu_dm_plane. This change does not change anything inside the
functions; the only exception is converting some static functions to a
global function.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why & How]
In order to leverage igt tool to maintain mst feature, expose new
debugfs entry "mst_progress_status".
In our dm flow, record down the result of each phase of mst and user
can examine the mst result by checking whether each phase get completed
successfully.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why & How]
Add "is_mst_connector" debugfs entry to help distinguish whether
a connector is in a mst topology or not.
Access it with the following command:
cat /sys/kernel/debug/dri/0/DP-X/is_mst_connector
Result:
- "root" stands for the root connector of the topology
- "branch" stands for branch device of the topology
- "end" stands for leaf node connector of the topology
- "no" stands for the connector is not a device of a mst topology
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why & How]
Correct few problems below to have debugfs trigger_hotplug entry
supports mst case
* Adjust the place for acquiring the hpd_lock. We'll also access
dc_link when simulate unplug
* When detect the connector is a mst root, call
reset_cur_dp_mst_topology() to simulate unplug
* Don't support hotplug caused by CSN message since we can't change
mst topology info directly. We can't simulate that
* Clean up redundant code
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why & How]
Need to leverage this function out of dc_link.c. Change it to public.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Update DML to configure drr_display in vba struct.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
Chen-Yu Tsai
Fabio Estevam
Ben Dooks
Jason Gerecke
Guenter Roeck
Jason Wang
Basavaraj Natikar
Lukas Bulwahn
Dominik Czerwik
Liu Zixian
Jiang Jian
Harshit Mogalapalli
Tzung-Bi Shih
Zhang Jiaming
Alex Elder
Jian Shen
Dave Airlie
Jakub Kicinski
Abhinav Kumar
John Harrison
Nícolas F. R. A. Prado
Luben Tuikov
Rodrigo Siqueira
Wayne Lin
Alvin Lee