| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
If ->run() fails, it can either free the data structures it
allocated, or leave that task to ->free() which will be called
on failures.
However:
md.c calls ->free() even if ->private_data is NULL, which
causes problems in some personalities.
raid0.c frees the data, but doesn't clear ->private_data,
which will become a problem when we fix md.c
So better fix both these issues at once.
Reported-by: Richard W.M. Jones <rjones@redhat.com>
Fixes: 5aa61f427e4979be733e4847b9199ff9cc48a47e
URL: https://bugzilla.kernel.org/show_bug.cgi?id=94381
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Current implementation doesn't zero out the pages allocated.
Honor the __GFP_ZERO flag and zero out if set.
Cc: <stable@vger.kernel.org> # v3.14+
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
init_mm isn't a normal mm: it has swapper_pg_dir as its pgd (which
contains kernel mappings) and is used as the active_mm for the idle
thread.
When restoring the pgd after an EFI call, we write current->active_mm
into TTBR0. If the current task is actually the idle thread (e.g. when
initialising the EFI RTC before entering userspace), then the TLB can
erroneously populate itself with junk global entries as a result of
speculative table walks.
When we do eventually return to userspace, the task can end up hitting
these junk mappings leading to lockups, corruption or crashes.
This patch fixes the problem in the same way as the CPU suspend code by
ensuring that we never switch to the init_mm in efi_set_pgd and instead
point TTBR0 at the zero page. A check is also added to cpu_switch_mm to
BUG if we get passed swapper_pg_dir.
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Fixes: f3cdfd239da5 ("arm64/efi: move SetVirtualAddressMap() to UEFI stub")
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Commit b4b55cda5874 (Refine the way to release PCI IRQ resources)
introduced a regression in the PCI IRQ resource management by causing
the IRQ resource of a device, established when pci_enabled_device()
is called on a fully disabled device, to be released when the driver
is unbound from the device, regardless of the enable_cnt.
This leads to the situation that an ill-behaved driver can now make a
device unusable to subsequent drivers by an imbalance in their use of
pci_enable/disable_device(). That is a serious problem for secondary
drivers like vfio-pci, which are innocent of the transgressions of
the previous driver.
Since the solution of this problem is not immediate and requires
further discussion, revert commit b4b55cda5874 and the issue it was
supposed to address (a bug related to xen-pciback) will be taken
care of in a different way going forward.
Reported-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
A check that rejects a CDB with FUA bit set if no write cache is
emulated was added by the following commit:
fde9f50 target: Add sanity checks for DPO/FUA bit usage
The condition is as follows:
if (!dev->dev_attrib.emulate_fua_write ||
!dev->dev_attrib.emulate_write_cache)
However, this check is wrong if the backend device supports WCE but
"emulate_write_cache" is disabled.
This patch uses se_dev_check_wce() (previously named
spc_check_dev_wce) to invoke transport->get_write_cache() if the
device has a write cache or check the "emulate_write_cache" attribute
otherwise.
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christophe Vu-Brugier <cvubrugier@fastmail.fm>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch fixes a NULL pointer dereference triggered by a late
target_configure_device() -> alloc_workqueue() failure that results
in target_free_device() being called with DF_CONFIGURED already set,
which subsequently OOPses in destroy_workqueue() code.
Currently this only happens at modprobe target_core_mod time when
core_dev_setup_virtual_lun0() -> target_configure_device() fails,
and the explicit target_free_device() gets called.
To address this bug originally introduced by commit 0fd97ccf45, go
ahead and move DF_CONFIGURED to end of target_configure_device()
code to handle this special failure case.
Reported-by: Claudio Fleiner <cmf@daterainc.com>
Cc: Claudio Fleiner <cmf@daterainc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: <stable@vger.kernel.org> # v3.7+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch fixes a NULL pointer dereference OOPs with pSCSI backends
within target_core_stat.c code. The bug is caused by a configfs attr
read if no pscsi_dev_virt->pdv_sd has been configured.
Reported-by: Olaf Hering <olaf@aepfle.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch adds a missing set of conditional check braces in
ft_invl_hw_context() originally introduced by commit dcd998ccd
when handling DDP failures in ft_recv_write_data() code.
commit dcd998ccdbf74a7d8fe0f0a44e85da1ed5975946
Author: Kiran Patil <kiran.patil@intel.com>
Date: Wed Aug 3 09:20:01 2011 +0000
tcm_fc: Handle DDP/SW fc_frame_payload_get failures in ft_recv_write_data
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Kiran Patil <kiran.patil@intel.com>
Cc: <stable@vger.kernel.org> # 3.1+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch fixes a se_cmd->cmd_kref leak buf when se_sess->sess_tearing_down
is true within target_get_sess_cmd() submission path code.
This se_cmd reference leak can occur during active session shutdown when
ack_kref=1 is passed by target_submit_cmd_[map_sgls,tmr]() callers.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: <stable@vger.kernel.org> # 3.6+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch changes loopback, usb-gadget, vhost-scsi and xen-scsiback
fabric code to invoke transport_register_session() instead of the
unprotected flavour, to ensure se_tpg->session_lock is taken when
adding new session list nodes to se_tpg->tpg_sess_list.
Note that since these four fabric drivers already hold their own
internal TPG mutexes when accessing se_tpg->tpg_sess_list, and
consist of a single se_session created through configfs attribute
access, no list corruption can currently occur.
So for correctness sake, go ahead and use the se_tpg->session_lock
protected version for these four fabric drivers.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch fixes the incorrect use of __transport_register_session()
in tcm_qla2xxx_check_initiator_node_acl() code, that does not perform
explicit se_tpg->session_lock when accessing se_tpg->tpg_sess_list
to add new se_sess nodes.
Given that tcm_qla2xxx_check_initiator_node_acl() is not called with
qla_hw->hardware_lock held for all accesses of ->tpg_sess_list, the
code should be using transport_register_session() instead.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: <stable@vger.kernel.org> # 3.5+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch fixes a iser specific logout bug where early complete()
of conn->conn_logout_comp in iscsit_close_connection() was causing
isert_wait4logout() to complete too soon, triggering a use after
free NULL pointer dereference of iscsi_conn memory.
The complete() was originally added for traditional iscsi-target
when a ISCSI_LOGOUT_OP failed in iscsi_target_rx_opcode(), but given
iser-target does not wait in logout failure, this special case needs
to be avoided.
Reported-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Slava Shwartsman <valyushash@gmail.com>
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This reverts commit 72859d91d93319c00a18c29f577e56bf73a8654a.
The original patch was wrong, iscsit_close_connection() still needs
to release iscsi_conn during both normal + exception IN_LOGOUT status
with ib_isert enabled.
The original OOPs is due to completing conn_logout_comp early within
iscsit_close_connection(), causing isert_wait4logout() to complete
instead of waiting for iscsit_logout_post_handler_*() to be called.
Reported-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Slava Shwartsman <valyushash@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Now that incoming FUA=1 bit check is enforced for backends with FUA or
WCE disabled, go ahead and disallow the changing of related backend
attributes when active fabric exports exist.
This is required to avoid potential failures with existing initiator
LUN registrations that have been previously created with FUA=1.
Reported-by: Christoph Hellwig <hch@lst.de>
Cc: Doug Gilbert <dgilbert@interlog.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Ronnie Sahlberg <ronniesahlberg@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Due to a merge error when creating c5c707f9 ("nfsd: implement pNFS
layout recalls"), we recursively call nfsd4_cb_layout_fail from itself,
leading to stack overflows.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Fixes: c5c707f9 ("nfsd: implement pNFS layout recalls")
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
---
fs/nfsd/nfs4layouts.c | 2 --
1 file changed, 2 deletions(-)
diff --git a/fs/nfsd/nfs4layouts.c b/fs/nfsd/nfs4layouts.c
index 3c1bfa1..1028a06 100644
--- a/fs/nfsd/nfs4layouts.c
+++ b/fs/nfsd/nfs4layouts.c
@@ -587,8 +587,6 @@ nfsd4_cb_layout_fail(struct nfs4_layout_stateid *ls)
rpc_ntop((struct sockaddr *)&clp->cl_addr, addr_str, sizeof(addr_str));
- nfsd4_cb_layout_fail(ls);
-
printk(KERN_WARNING
"nfsd: client %s failed to respond to layout recall. "
" Fencing..\n", addr_str);
--
1.9.1
|
|
The misc subsystem (which is used for /dev/fuse) initializes private_data to
point to the misc device when a driver has registered a custom open file
operation, and initializes it to NULL when a custom open file operation has
*not* been provided.
This subtle quirk is confusing, to the point where kernel code registers
*empty* file open operations to have private_data point to the misc device
structure. And it leads to bugs, where the addition or removal of a custom open
file operation surprisingly changes the initial contents of a file's
private_data structure.
So to simplify things in the misc subsystem, a patch [1] has been proposed to
*always* set the private_data to point to the misc device, instead of only
doing this when a custom open file operation has been registered.
But before this patch can be applied we need to modify drivers that make the
assumption that a misc device file's private_data is initialized to NULL
because they didn't register a custom open file operation, so they don't rely
on this assumption anymore. FUSE uses private_data to store the fuse_conn and
errors out if this is not initialized to NULL at mount time.
Hence, we now set a file's private_data to NULL explicitly, to be independent
of whatever value the misc subsystem initializes it to by default.
[1] https://lkml.org/lkml/2014/12/4/939
Reported-by: Giedrius Statkevicius <giedriuswork@gmail.com>
Reported-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Tom Van Braeckel <tomvanbraeckel@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
|
|
This reverts commit 2fa645cb2703d9b3786d850db815414dfeefa51d.
The assumption that at least 1 preferred console will be registered
when the stdout-path property is set is invalid, which can result
in _no_ consoles.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Commit 106937e8ccdc ("of: fix handling of '/' in options for
of_find_node_by_path()") caused a regression in OF handling of
stdout-path. While it fixes some cases which have '/' after the ':', it
breaks cases where there is more than one '/' *before* the ':'.
For example, it breaks this boot string
stdout-path = "/rdb/serial@f040ab00:115200";
So rather than doing sequentialized checks (first for '/', then for ':';
or vice versa), to get the correct behavior we need to check for the
first occurrence of either one of them.
It so happens that the handy strcspn() helper can do just that.
Fixes: 106937e8ccdc ("of: fix handling of '/' in options for of_find_node_by_path()")
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: stable@vger.kernel.org # 3.19
Acked-by: Leif Lindholm <leif.lindholm@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
There were regressions seen with commit 106937e8ccdc ("of: fix handling
of '/' in options for of_find_node_by_path()"), where we couldn't handle
extra '/' before the ':'. Let's test for this now.
Confirmed that this test fails without the previous patch and passes
when patched. All other tests pass.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Leif Lindholm <leif.lindholm@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
The error code paths that require cleanup use a goto to jump to the
cleanup code and return an error code. However, the error code variable
res, which is initialized to -EINVAL when declared, is then overwritten
with the return value of of_parse_phandle_with_args(), and reused as the
return code from of_irq_parse_one(). This leads to an undetermined error
being returned instead of the expected -EINVAL value. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Cc: stable@vger.kernel.org # 3.13+
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
The current error-path code (when gpiod_get_index() reports
an error) can never free pwrseq->reset_gpios[0], but might
try to tree pwrseq->reset_gpios[-1], which has unfortunate
consequences.
Signed-off-by: NeilBrown <neil@brown.name>
Fixes: 934f1f48330ed695927a51fa068dc5d673f2da19
Acked-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reported-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
|
|
Use jiffies_to_msecs for converting jiffies as it handles all of the corner
cases reliably and also helps readability. The printk format is fixed up
as jiffies_to_msecs returns unsigned int not unsigned long.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 11ad714b98f6d9ca0067568442afe3e70eb94845 because
it breaks cx82310_eth.
The custom USB_DEVICE_CLASS macro matches
bDeviceClass, bDeviceSubClass and bDeviceProtocol
but the common USB_DEVICE_AND_INTERFACE_INFO matches
bInterfaceClass, bInterfaceSubClass and bInterfaceProtocol instead, which are
not specified.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
/proc/kcore investigates the "System RAM" elements in /proc/iomem to
initialize it's memory tables. Therefore we have to register them
before it tries to do so. kcore uses device_initcall() so let's
use arch_initcall() for the registry.
Also we need ARCH_PROC_KCORE_TEXT to get the virtual addresses of
the kernel image correct.
Reported-by: David Ahern <david.ahern@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Port statistics bitmap will now be initialized at port init. Even before
starting the port, statistics are visible to the user and must be properly masked.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For RoCE ports, we set the u32 PMA values based on u64 HCA counters. In case of
overflow, according to the IB spec, we have to saturate a counter to its
max value, do that.
Fixes: c37791349cc7 ('IB/mlx4: Support PMA counters for IBoE')
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NUM_PORT_STATS was 9 instead of 10, which caused off-by-one bug when
displaying the statistics starting from tx_chksum_offload in ethtool.
Fixes: f8c6455bb04b ('net/mlx4_en: Extend checksum offloading by CHECKSUM COMPLETE')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Processing an event is done in a different context from the one when
the event was dispatched. This requires a check that the slave
net device is still valid when the event is being processed. The check is done
under the iboe lock which ensure correctness.
Fixes: a57500903093 ('IB/mlx4: Add port aggregation support')
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ensure that clients can automatically configure themselves and avoid a
nasty warning at boot by providing capability information.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
We should signal connect (pull up dp) after we have already
at peripheral mode, otherwise, the dp may be toggled due to
we reset controller or do disconnect during the initialization
for peripheral, then, the host may be confused during the
enumeration, eg, it finds the reset can't succeed, but the
device is still there, see below error message.
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
hub 1-0:1.0: unable to enumerate USB device on port 1
Fixes: the issue existed when the otg fsm code was added.
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A new uas compatible controller has shown up in some people's devices from
the manufacturer Initio Corporation, this controller needs the US_FL_NO_ATA_1X
quirk to work properly with uas, so add it to the uas quirks table.
Reported-and-tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
radeon_bo_create() calls radeon_ttm_placement_from_domain()
before ttm_bo_init() is called. radeon_ttm_placement_from_domain()
uses the ttm bo size to determine when to select top down
allocation but since the ttm bo is not initialized yet the
check is always false. It only took effect when buffers
were validated later. It also seemed to regress suspend
and resume on some systems possibly due to it not
taking effect in radeon_bo_create().
radeon_bo_create() and radeon_ttm_placement_from_domain()
need to be reworked substantially for this to be optimally
effective. Re-enable it at that point.
Noticed-by: Oded Gabbay <oded.gabbay@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
The EHCI IP only needs the UTMI/UPLL (uclk) and the peripheral (iclk)
clocks to work properly. Remove the useless system clock (fclk).
Avoid calling set_rate on the fixed rate UTMI/IPLL clock and remove
useless IS_ENABLED(CONFIG_COMMON_CLK) tests (all at91 platforms have been
moved to the CCF).
This patch also fixes a bug introduced by 3440ef1 (ARM: at91/dt: fix USB
high-speed clock to select UTMI), which was leaving the usb clock
uninitialized and preventing the OHCI driver from setting the usb clock
rate to 48MHz.
This bug was caused by several things:
1/ usb clock drivers set the CLK_SET_RATE_GATE flag, which means the rate
cannot be changed once the clock is prepared
2/ The EHCI driver was retrieving and preparing/enabling the uhpck
clock which was in turn preparing its parent clock (the usb clock),
thus preventing any rate change because of 1/
Fixes: 3440ef169100 ("ARM: at91/dt: fix USB high-speed clock to select UTMI")
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since commit 0f04cf8df0b20a97369cb634663fef0578cbf273 ("drm/exynos:
fix wrong pipe calculation for crtc"), fimd_clear_channel() can be
called when is_drm_iommu_supported() returns true. In this case,
the kernel is going to be panicked because crtc is not set yet.
[ 1.211156] [drm] Initialized drm 1.1.0 20060810
[ 1.216785] Unable to handle kernel NULL pointer dereference at virtual address 00000350
[ 1.223415] pgd = c0004000
[ 1.226086] [00000350] *pgd=00000000
[ 1.229649] Internal error: Oops: 5 [#1] PREEMPT SMP ARM
[ 1.234940] Modules linked in:
[ 1.237982] CPU: 2 PID: 1 Comm: swapper/0 Not tainted 4.0.0-rc1-00062-g7a7cc79-dirty #123
[ 1.246136] Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[ 1.252214] task: ee8c8000 ti: ee8d0000 task.ti: ee8d0000
[ 1.257606] PC is at fimd_wait_for_vblank+0x8/0xc8
[ 1.262370] LR is at fimd_bind+0x138/0x1a8
[ 1.266450] pc : [<c02fb63c>] lr : [<c02fb834>] psr: 20000113
[ 1.266450] sp : ee8d1d28 ip : 00000000 fp : 00000000
[ 1.277906] r10: 00000001 r9 : c09d693c r8 : c0a2d6a8
[ 1.283114] r7 : 00000034 r6 : 00000001 r5 : ee0bb400 r4 : ee244c10
[ 1.289624] r3 : 00000000 r2 : 00000000 r1 : 00000001 r0 : 00000000
[ 1.296135] Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
[ 1.303426] Control: 10c5387d Table: 4000404a DAC: 00000015
[ 1.309154] Process swapper/0 (pid: 1, stack limit = 0xee8d0210)
[ 1.315143] Stack: (0xee8d1d28 to 0xee8d2000)
[ 1.319486] 1d20: 00000000 c0113d18 ee0bb400 ee0bb400 ee245c30 eebbe210
[ 1.327645] 1d40: ee008a40 ee244c10 ee0bb400 00000001 00000034 c02fb834 00000000 c030a858
[ 1.335804] 1d60: ee244a10 eeb60780 ee008a40 eeb60740 ee0bb400 c03030d0 00000000 00000000
[ 1.343963] 1d80: ee244a10 ee0bb400 00000000 eeb60740 eeb60810 00000000 00000000 c02f6ba4
[ 1.352123] 1da0: ee0bb400 00000000 00000000 c02e0500 ee244a00 c0a04a14 ee0bb400 c02e1de4
[ 1.360282] 1dc0: 00000000 c030a858 00000002 eeb60820 eeb60820 00000002 eeb60780 c03033d4
[ 1.368441] 1de0: c06e9cec 00000000 ee244a10 eeb60780 c0a056f8 c03035fc c0a04b24 c0a04b24
[ 1.376600] 1e00: ee244a10 00000001 c0a049d0 c02f6d34 c0ad462c eeba0790 00000000 ee244a10
[ 1.384759] 1e20: ffffffed c0a049d0 00000000 c03090b0 ee244a10 c0ad462c c0a2d840 c03077a0
[ 1.392919] 1e40: eeb5e880 c024b738 000008db ee244a10 c0a049d0 ee244a44 00000000 c09e71d8
[ 1.401078] 1e60: 000000c6 c0307a6c c0a049d0 00000000 c03079e0 c0305ea8 ee826e5c ee1dc7b4
[ 1.409237] 1e80: c0a049d0 eeb5e880 c0a058a8 c0306e2c c0896204 c0a049d0 c06e9d10 c0a049d0
[ 1.417396] 1ea0: c06e9d10 c0ad4600 00000000 c0308360 00000000 00000003 c06e9d10 c02f6e14
[ 1.425555] 1ec0: 00000000 c0896204 ffffffff 00000000 00000000 00000000 00000000 00000000
[ 1.433714] 1ee0: 00000000 00000000 c02f6d5c c02f6d5c 00000000 eeb5d740 c09e71d8 c0008a30
[ 1.441874] 1f00: ef7fca5e 00000000 00000000 00000066 00000000 ee8d1f28 c003ff1c c02514e8
[ 1.450033] 1f20: 60000113 ffffffff c093906c ef7fca5e 000000c6 c004018c 00000000 c093906c
[ 1.458192] 1f40: c08a9690 c093840c 00000006 00000006 c09eb2ac c09c0d74 00000006 c09c0d54
[ 1.466351] 1f60: c0a3d680 c09745a0 c09d693c 000000c6 00000000 c0974db4 00000006 00000006
[ 1.474510] 1f80: c09745a0 ffffffff 00000000 c0692e00 00000000 00000000 00000000 00000000
[ 1.482669] 1fa0: 00000000 c0692e08 00000000 c000f040 00000000 00000000 00000000 00000000
[ 1.490828] 1fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 1.498988] 1fe0: 00000000 00000000 00000000 00000000 00000013 00000000 ffffffff ffffffff
[ 1.507159] [<c02fb63c>] (fimd_wait_for_vblank) from [<c02fb834>] (fimd_bind+0x138/0x1a8)
[ 1.515313] [<c02fb834>] (fimd_bind) from [<c03030d0>] (component_bind_all+0xc4/0x20c)
[ 1.523209] [<c03030d0>] (component_bind_all) from [<c02f6ba4>] (exynos_drm_load+0xa0/0x140)
[ 1.531632] [<c02f6ba4>] (exynos_drm_load) from [<c02e0500>] (drm_dev_register+0xa0/0xf4)
[ 1.539788] [<c02e0500>] (drm_dev_register) from [<c02e1de4>] (drm_platform_init+0x44/0xcc)
[ 1.548121] [<c02e1de4>] (drm_platform_init) from [<c03033d4>] (try_to_bring_up_master.part.1+0xc8/0x104)
[ 1.557668] [<c03033d4>] (try_to_bring_up_master.part.1) from [<c03035fc>] (component_master_add_with_match+0xd0/0x118)
[ 1.568431] [<c03035fc>] (component_master_add_with_match) from [<c02f6d34>] (exynos_drm_platform_probe+0xf0/0x118)
[ 1.578847] [<c02f6d34>] (exynos_drm_platform_probe) from [<c03090b0>] (platform_drv_probe+0x48/0x98)
[ 1.588052] [<c03090b0>] (platform_drv_probe) from [<c03077a0>] (driver_probe_device+0x140/0x380)
[ 1.596902] [<c03077a0>] (driver_probe_device) from [<c0307a6c>] (__driver_attach+0x8c/0x90)
[ 1.605321] [<c0307a6c>] (__driver_attach) from [<c0305ea8>] (bus_for_each_dev+0x54/0x88)
[ 1.613480] [<c0305ea8>] (bus_for_each_dev) from [<c0306e2c>] (bus_add_driver+0xec/0x200)
[ 1.621640] [<c0306e2c>] (bus_add_driver) from [<c0308360>] (driver_register+0x78/0xf4)
[ 1.629625] [<c0308360>] (driver_register) from [<c02f6e14>] (exynos_drm_init+0xb8/0x11c)
[ 1.637785] [<c02f6e14>] (exynos_drm_init) from [<c0008a30>] (do_one_initcall+0xac/0x1ec)
[ 1.645950] [<c0008a30>] (do_one_initcall) from [<c0974db4>] (kernel_init_freeable+0x194/0x268)
[ 1.654626] [<c0974db4>] (kernel_init_freeable) from [<c0692e08>] (kernel_init+0x8/0xe4)
[ 1.662699] [<c0692e08>] (kernel_init) from [<c000f040>] (ret_from_fork+0x14/0x34)
[ 1.670246] Code: eaffffd5 c09df884 e92d40f0 e24dd01c (e5905350)
[ 1.676408] ---[ end trace 804468492f306a6f ]---
[ 1.680948] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
[ 1.680948]
[ 1.690035] CPU1: stopping
[ 1.692727] CPU: 1 PID: 0 Comm: swapper/1 Tainted: G D 4.0.0-rc1-00062-g7a7cc79-dirty #123
[ 1.702097] Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[ 1.708192] [<c0016c84>] (unwind_backtrace) from [<c00129bc>] (show_stack+0x10/0x14)
[ 1.715908] [<c00129bc>] (show_stack) from [<c0696f58>] (dump_stack+0x78/0xc8)
[ 1.723108] [<c0696f58>] (dump_stack) from [<c0015020>] (handle_IPI+0x16c/0x2b4)
[ 1.730485] [<c0015020>] (handle_IPI) from [<c00086bc>] (gic_handle_irq+0x64/0x6c)
[ 1.738036] [<c00086bc>] (gic_handle_irq) from [<c00134c0>] (__irq_svc+0x40/0x74)
[ 1.745498] Exception stack(0xee8fdf98 to 0xee8fdfe0)
[ 1.750533] df80: 00000000 00000000
[ 1.758695] dfa0: ee8fdfe8 c0021780 c09df938 00000015 10c0387d c0a3d988 4000406a c09df8d4
[ 1.766853] dfc0: c0a27a74 c09df940 01000000 ee8fdfe0 c00101c0 c00101c4 60000113 ffffffff
[ 1.775015] [<c00134c0>] (__irq_svc) from [<c00101c4>] (arch_cpu_idle+0x30/0x3c)
[ 1.782397] [<c00101c4>] (arch_cpu_idle) from [<c005e804>] (cpu_startup_entry+0x180/0x324)
[ 1.790639] [<c005e804>] (cpu_startup_entry) from [<40008764>] (0x40008764)
[ 1.797579] CPU0: stopping
[ 1.800272] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G D 4.0.0-rc1-00062-g7a7cc79-dirty #123
[ 1.809642] Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[ 1.815730] [<c0016c84>] (unwind_backtrace) from [<c00129bc>] (show_stack+0x10/0x14)
[ 1.823450] [<c00129bc>] (show_stack) from [<c0696f58>] (dump_stack+0x78/0xc8)
[ 1.830653] [<c0696f58>] (dump_stack) from [<c0015020>] (handle_IPI+0x16c/0x2b4)
[ 1.838030] [<c0015020>] (handle_IPI) from [<c00086bc>] (gic_handle_irq+0x64/0x6c)
[ 1.845581] [<c00086bc>] (gic_handle_irq) from [<c00134c0>] (__irq_svc+0x40/0x74)
[ 1.853043] Exception stack(0xc09ddf60 to 0xc09ddfa8)
[ 1.858081] df60: 00000000 00000000 c09ddfb0 c0021780 c09df938 00000001 ffffffff c0a3d680
[ 1.866239] df80: c09c0dec c09df8d4 c0a27a74 c09df940 01000000 c09ddfa8 c00101c0 c00101c4
[ 1.874396] dfa0: 60000113 ffffffff
[ 1.877872] [<c00134c0>] (__irq_svc) from [<c00101c4>] (arch_cpu_idle+0x30/0x3c)
[ 1.885251] [<c00101c4>] (arch_cpu_idle) from [<c005e804>] (cpu_startup_entry+0x180/0x324)
[ 1.893499] [<c005e804>] (cpu_startup_entry) from [<c0974bc8>] (start_kernel+0x324/0x37c)
[ 1.901655] [<c0974bc8>] (start_kernel) from [<40008074>] (0x40008074)
[ 1.908161] CPU3: stopping
[ 1.910855] CPU: 3 PID: 0 Comm: swapper/3 Tainted: G D 4.0.0-rc1-00062-g7a7cc79-dirty #123
[ 1.920225] Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[ 1.926313] [<c0016c84>] (unwind_backtrace) from [<c00129bc>] (show_stack+0x10/0x14)
[ 1.934034] [<c00129bc>] (show_stack) from [<c0696f58>] (dump_stack+0x78/0xc8)
[ 1.941237] [<c0696f58>] (dump_stack) from [<c0015020>] (handle_IPI+0x16c/0x2b4)
[ 1.948613] [<c0015020>] (handle_IPI) from [<c00086bc>] (gic_handle_irq+0x64/0x6c)
[ 1.956165] [<c00086bc>] (gic_handle_irq) from [<c00134c0>] (__irq_svc+0x40/0x74)
[ 1.963626] Exception stack(0xee901f98 to 0xee901fe0)
[ 1.968661] 1f80: 00000000 00000000
[ 1.976823] 1fa0: ee901fe8 c0021780 c09df938 00000015 10c0387d c0a3d988 4000406a c09df8d4
[ 1.984982] 1fc0: c0a27a74 c09df940 01000000 ee901fe0 c00101c0 c00101c4 60000113 ffffffff
[ 1.993143] [<c00134c0>] (__irq_svc) from [<c00101c4>] (arch_cpu_idle+0x30/0x3c)
[ 2.000522] [<c00101c4>] (arch_cpu_idle) from [<c005e804>] (cpu_startup_entry+0x180/0x324)
[ 2.008765] [<c005e804>] (cpu_startup_entry) from [<40008764>] (0x40008764)
[ 2.015710] ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
This patch fixes DRM_EXYNOS7DECON to DRM_EXYNOS7_DECON.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
The commit "drm/exynos: remove exynos_plane_dpms" (d9ea6256) removed the
use of the enabled flag, which means that the code may attempt to call
win_enable on a NULL crtc. This results in the following oops on
Arndale:
[ 1.673479] Unable to handle kernel NULL pointer dereference at virtual address 00000368
[ 1.681500] pgd = c0004000
[ 1.684154] [00000368] *pgd=00000000
[ 1.687713] Internal error: Oops: 5 [#1] PREEMPT SMP ARM
[ 1.693012] Modules linked in:
[ 1.696045] CPU: 1 PID: 1 Comm: swapper/0 Not tainted
3.19.0-07545-g57485fa #1907
[ 1.703524] Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
(....)
[ 2.014803] [<c02f9cfc>] (exynos_plane_destroy) from [<c02e61b4>] (drm_mode_config_cleanup+0x168/0x20c)
[ 2.024178] [<c02e61b4>] (drm_mode_config_cleanup) from [<c02f66fc>] (exynos_drm_load+0xac/0x12c)
This patch adds in a check to ensure exynos_crtc is not NULL before it
is dereferenced.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
of_iomap() doesn't return error pointers, it returns NULL on error.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
These files are not used anymore.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Replace inline asm statement in __get_cpu_architecture() with equivalent
macro invocation, i.e. read_cpuid_ext(CPUID_EXT_MMFR0);
As an added bonus, this squashes a potential bug, described by Paul
Walmsley in commit 067e710b9a98 ("ARM: 7801/1: prevent gcc 4.5 from
reordering extended CP15 reads above is_smp() test").
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The set_memory_* functions currently only support module
addresses. The addresses are validated using is_module_addr.
That function is special though and relies on internal state
in the module subsystem to work properly. At the time of
module initialization and calling set_memory_*, it's too early
for is_module_addr to work properly so it always returns
false. Rather than be subject to the whims of the module state,
just bounds check against the module virtual address range.
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Allow prefetch settings overriding by device tree, in case
l2x0_cache_size_of_parse() returns value, prefetch tuning
properties are silently ignored. E.g. arm,double-linefill* and
arm,prefetch*.
This happens for example, when "cache-size" or "cache-sets"
properties haven't been filled in l2c dt node.
Comments from Fabrice Gasnier:
Allow device tree to override the L2C prefetch settings, even when
l2x0_cache_size_of_parse() fails to parse the cache geometry due to (eg)
missing "cache-size" or "cache-sets" properties.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
On sun4i-a10, when GPIOs are configured as external interrupt the value for
them in the data register does not seem to get updated, so set their mux to
input (and restore afterwards) when reading the pin.
Missed edges seem to be buffered, so this does not introduce a race
condition.
I've also tested this on sun5i-a13 and sun7i-a20 and those do not seem to
be affected, the input value representation in the data register does seem
to correctly get updated to the actual pin value while in irq mode there.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
After importing multi-lower layer support, users could mount a r/o
partition as the left most lowerdir instead of using it as upperdir.
And a r/o upperdir may cause an error like
overlayfs: failed to create directory ./workdir/work
during mount.
This patch check the *s_flags* of upper fs and return an error if
it is a r/o partition. The checking of *upper_mnt->mnt_sb->s_flags*
can be removed now.
This patch also remove
/* FIXME: workdir is not needed for a R/O mount */
from ovl_fill_super() because:
1) for upper fs r/o case
Setting a r/o partition as upper is prevented, no need to care about
workdir in this case.
2) for "mount overlay -o ro" with a r/w upper fs case
Users could remount overlayfs to r/w in this case, so workdir should
not be omitted.
Signed-off-by: hujianyang <hujianyang@huawei.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
|
|
Recently multi-lower layer mount support allow upperdir and workdir
to be omitted, then cause overlayfs can be mount with only one
lowerdir directory. This action make no sense and have potential risk.
This patch check the total number of lower directories to prevent
mounting overlayfs with only one directory.
Also, an error message is added to indicate lower directories exceed
OVL_MAX_STACK limit.
Signed-off-by: hujianyang <hujianyang@huawei.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
|
|
Overlayfs should print an error message if an incorrect mount option
is caught like other filesystems.
After this patch, improper option input could be clearly known.
Reported-by: Fabian Sturm <fabian.sturm@aduu.de>
Signed-off-by: hujianyang <hujianyang@huawei.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
|
|
We don't want to end up in a state where we track that the pipe has its
primary plane enabled when primary plane registers are programmed with
values that look possible but the plane actually disabled.
Refuse to read out the fb state when the primary plane isn't enabled.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Suggested-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reported-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Reference: http://mid.gmane.org/20150203191507.GA2374@crion86
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Revisiting commit d23b8ad8ab23 ("tc: add BPF based action") with regards
to eBPF support, I was thinking that it might be better to improve
return semantics from a BPF program invoked through BPF_PROG_RUN().
Currently, in case filter_res is 0, we overwrite the default action
opcode with TC_ACT_SHOT. A default action opcode configured through tc's
m_bpf can be: TC_ACT_RECLASSIFY, TC_ACT_PIPE, TC_ACT_SHOT, TC_ACT_UNSPEC,
TC_ACT_OK.
In cls_bpf, we have the possibility to overwrite the default class
associated with the classifier in case filter_res is _not_ 0xffffffff
(-1).
That allows us to fold multiple [e]BPF programs into a single one, where
they would otherwise need to be defined as a separate classifier with
its own classid, needlessly redoing parsing work, etc.
Similarly, we could do better in act_bpf: Since above TC_ACT* opcodes
are exported to UAPI anyway, we reuse them for return-code-to-tc-opcode
mapping, where we would allow above possibilities. Thus, like in cls_bpf,
a filter_res of 0xffffffff (-1) means that the configured _default_ action
is used. Any unkown return code from the BPF program would fail in
tcf_bpf() with TC_ACT_UNSPEC.
Should we one day want to make use of TC_ACT_STOLEN or TC_ACT_QUEUED,
which both have the same semantics, we have the option to either use
that as a default action (filter_res of 0xffffffff) or non-default BPF
return code.
All that will allow us to transparently use tcf_bpf() for both BPF
flavours.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The gpiochip_lock_as_irq call can fail and return an error,
while the irq_startup is not expected to fail (returns an
unsigned int which is not checked by irq core code).
irq_request/release_resources functions have been created
to address this problem.
Move gpiochip_lock/unlock_as_irq calls into
irq_request/release_resources functions to prevent using a
gpio as an irq if the gpiochip_lock_as_irq call failed.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
There is a typo here so we deadlock.
Fixes: dd1f1f391dd7 ('rtc: at91rm9200: rework wakeup and interrupt handling')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: David Dueck <davidcdueck@googlemail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
We are keeping track of how many extents we need to reserve properly based on
the amount we want to write, but we were still incrementing outstanding_extents
if we wrote less than what we requested. This isn't quite right since we will
be limited to our max extent size. So instead lets do something horrible! Keep
track of how many outstanding_extents we reserved, and decrement each time we
allocate an extent. If we use our entire reserve make sure to jack up
outstanding_extents on the inode so the accounting works out properly. Thanks,
Reported-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Josef Bacik <jbacik@fb.com>
|
NeilBrown
Suzuki K. Poulose
Will Deacon
Rafael J. Wysocki
Christophe Vu-Brugier
Nicholas Bellinger
Dan Carpenter
Bart Van Assche
Christoph Hellwig
Tom Van Braeckel
Peter Hurley
Brian Norris
Laurent Pinchart
NeilBrown
Nicholas Mc Guire
Ondrej Zary
David S. Miller
Eran Ben Elisha
Majd Dibbiny
Moni Shoua
Mark Brown
Peter Chen
Hans de Goede
Alex Deucher
Boris Brezillon
Hyungwon Hwang
Inki Dae
Charles Keepax
Andrzej Hajda
Mason
Laura Abbott
Fabrice Gasnier
hujianyang
Damien Lespiau
Daniel Borkmann
Josef Bacik