linux-dev - Linux kernel development work

Age	Commit message (Collapse)	Author	Files	Lines
2013-12-09	ath9k: Use a separate TX gain table for WZR-HP-G450H	Sujith Manoharan	1	-0/+2
	The Buffalo device WZR-HP-G450H uses the index 3 for TX gain, which is set to the high_power table currently. Later variants of the router use the same index, but instead refer to the low_ob_db gain table. This is not handled in the driver since there is no way to distinguish board revisions and the high_power table is used (incorrectly) for the newer variants. By default, devices based on AR9300 using the TX gain index 3 have to use the high_power table. To make sure that WZR-HP-G450H is not broken when the high_power table is updated, use a separate array based on information obtained from the platform data. The current situation where only the original variant of WZR-HP-G450H works properly stays unchanged. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-12-10	ath9k: allow to load EEPROM content via firmware API	Gabor Juhos	1	-0/+2
	The calibration data for devices w/o a separate EEPROM chip can be specified via the 'eeprom_data' field of 'ath9k_platform_data'. The 'eeprom_data' is usually filled from board specific setup functions. It is easy if the EEPROM data is mapped to the memory, but it can be complicated if it is stored elsewhere. The patch adds support for loading of the EEPROM data via the firmware API to avoid this limitation. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22	ath9k: add external_reset callback to ath9k_platfom_data for AR9330	Gabor Juhos	1	-0/+1
	The patch adds a callback to ath9k_platform_data. If the callback is provided by the platform code, then it can be used to hard reset the WMAC device. The callback is required for doing a hard reset of the AR9330 chips to get them working again after a hang. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22	ath9k: add MAC revision detection for AR9330	Gabor Juhos	1	-0/+1
	The AR9330 1.0 and 1.1 are using the same revision, thus it is not possible to distinguish the two chips. The platform setup code can distinguish the chips based on the SoC revision. Add a callback function to ath9k_platform_data in order to allow getting the revision number from the platform code. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-25	ath9k_hw: Get AHB clock information from ath9k_platform_data	Vasanthakumar Thiagarajan	1	-0/+2
	Add a bool in ath9k_platform_data to pass AHB clock speed information. Driver needs this to configure PLL on some SOCs. Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-03-30	ath9k: add support for overriding LED pin and GPIO settings from platform data	Felix Fietkau	1	-0/+4
	Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-03-30	ath9k: add support for overriding the MAC address through platform data	Felix Fietkau	1	-0/+1
	On some devices the correct MAC address is not in the EEPROM data, but stored somewhere else. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29	ath9k: get EEPROM contents from platform data on AHB bus	Gabor Juhos	1	-0/+28
	On the AR913x SOCs we have to provide EEPROM contents via platform_data, because accessing the flash via MMIO is not safe. Additionally different boards may store the radio calibration data at different locations. Changes-licensed-under: ISC Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: Imre Kaloz <kaloz@openwrt.org> Tested-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>