| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The PCI channel could go offline during reset due to EEH. Don't bug on in
this case, the error is recoverable.
Fixes: f6bc11e42646 ('net/mlx4_core: Enhance the catas flow to support device reset')
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The error flow in procedure handle_existing_counter() is wrong.
The procedure should exit after encountering the error, not continue
as if everything is OK.
Fixes: 68230242cdbc ('net/mlx4_core: Add port attribute when tracking counters')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously, the shift value used for time-stamping was constant and didn't
depend on the HW chip frequency. Change that to take the frequency into account
and calculate the maximal value in cycles per wraparound of ten seconds. This
time slot was chosen since it gives a good accuracy in time synchronization.
Algorithm for shift value calculation:
* Round up the maximal value in cycles to nearest power of two
* Calculate maximal multiplier by division of all 64 bits set
to above result
* Then, invert the function clocksource_khz2mult() to get the shift from
maximal mult value
Fixes: ec693d47010e ('net/mlx4_en: Add HW timestamping (TS) support')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RdropOvflw counts overrun of HW buffer, therefore should
be used for rx_fifo_errors only.
Currently RdropOvflw counter is mistakenly also set into
rx_missed_errors and rx_over_errors too, which makes the
device total dropped packets accounting to show wrong results.
Fix that. Use it for rx_fifo_errors only.
Fixes: c27a02cd94d6 ('mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC')
Signed-off-by: Amir Vadai <amir@vadai.me>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Thomas reports:
T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=05c6 ProdID=6001 Rev=00.00
S: Manufacturer=USB Modem
S: Product=USB Modem
S: SerialNumber=1234567890ABCDEF
C: #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I: If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If tcp_v4_inbound_md5_hash() returns an error, we must release
the refcount on the request socket, not on the listener.
The bug was added for IPv4 only.
Fixes: 079096f103fac ("tcp/dccp: install syn_recv requests into ehash table")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are some cases where rtt_us derives from deltas of jiffies,
instead of using usec timestamps.
Since we want to track minimal rtt, better to assume a delta of 0 jiffie
might be in fact be very close to 1 jiffie.
It is kind of sad jiffies_to_usecs(1) calls a function instead of simply
using a constant.
Fixes: f672258391b42 ("tcp: track min RTT using windowed min-filter")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
add new id (CONTEC C-NET(PC)C-100TX2)
Signed-off-by: Ken Kawasaki <ken_kawasaki@nifty.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The phy has not been initialized, disconnecting it in the error
path results in a NULL pointer exception. Drop the phy_disconnect
from the error path.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Marvell 88E6240 has been tested successfully without further
changes. Add entry to the table of supported devices.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit 5266698661401a ("tipc: let broadcast packet reception
use new link receive function") we introduced a new per-node
broadcast reception link instance. This link is created at the
moment the node itself is created. Unfortunately, the allocation
is done after the node instance has already been added to the node
lookup hash table. This creates a potential race condition, where
arriving broadcast packets are able to find and access the node
before it has been fully initialized, and before the above mentioned
link has been created. The result is occasional crashes in the function
tipc_bcast_rcv(), which is trying to access the not-yet existing link.
We fix this by deferring the addition of the node instance until after
it has been fully initialized in the function tipc_node_create().
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current default tx ring size of 512 causes an extra page to be
allocated for the tx ring with only 1 entry in it. Reduce it to
511. The default rx ring size is also reduced to 511 to use less
memory by default.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tx push is supported for small packets to reduce DMA latency. The
following bugs are fixed in this patch:
1. Fix the definition of the push BD which is different from the DMA BD.
2. The push buffer has to be zero padded to the next 64-bit word boundary
or tx checksum won't be correct.
3. Increase the tx push packet threshold to 164 bytes (192 bytes with the BD)
so that small tunneled packets are within the threshold.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
20G is not supported by production hardware and only the 40GbaseCR4 standard
is supported.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cleanup bnxt_probe_phy() to cleanly separate 2 code blocks for autoneg
on and off. Autoneg flow control is possible only if autoneg is enabled.
In bnxt_get_settings(), Pause and Asym_Pause are always supported.
Only the advertisement bits change depending on the ethtool -A setting
in auto mode.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1. Determine autoneg on|off setting from link_info->autoneg. Using the
firmware returned setting can be misleading if autoneg is changed and
there hasn't been a phy update from the firmware.
2. If autoneg is disabled, link_info->autoneg should be set to 0 to
indicate both speed and flow control autoneg are disabled.
3. To enable autoneg flow control, speed autoneg must be enabled.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A recent change to the mdb code confused the compiler to the point
where it did not realize that the port-group returned from
br_mdb_add_group() is always valid when the function returns a nonzero
return value, so we get a spurious warning:
net/bridge/br_mdb.c: In function 'br_mdb_add':
net/bridge/br_mdb.c:542:4: error: 'pg' may be used uninitialized in this function [-Werror=maybe-uninitialized]
__br_mdb_notify(dev, entry, RTM_NEWMDB, pg);
Slightly rearranging the code in br_mdb_add_group() makes the problem
go away, as gcc is clever enough to see that both functions check
for 'ret != 0'.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 9e8430f8d60d ("bridge: mdb: Passing the port-group pointer to br_mdb module")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
EMAC could be disabled, while there is some sb_buff
in use. That buffers got lost for linux.
In order to reproduce run on device during active ethernet work:
ifconfig eth0 down
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
EMAC reset internal tx ring pointer to zero at statup.
txbd_curr and txbd_dirty can be different from zero.
That cause ethernet transfer hang (no packets transmitted).
In order to reproduce, run on device:
ifconfig eth0 down
ifconfig eth0 up
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a race between arc_emac_tx() and arc_emac_tx_clean().
sk_buff got freed by arc_emac_tx_clean() while arc_emac_tx()
submitting sk_buff.
In order to free sk_buff arc_emac_tx_clean() checks:
if ((info & FOR_EMAC) || !txbd->data)
break;
...
dev_kfree_skb_irq(skb);
If condition false, arc_emac_tx_clean() free sk_buff.
In order to submit txbd, arc_emac_tx() do:
priv->tx_buff[*txbd_curr].skb = skb;
...
priv->txbd[*txbd_curr].data = cpu_to_le32(addr);
...
... <== arc_emac_tx_clean() check condition here
... <== (info & FOR_EMAC) is false
... <== !txbd->data is false
...
*info = cpu_to_le32(FOR_EMAC | FIRST_OR_LAST_MASK | len);
In order to reproduce the situation,
run device:
# iperf -s
run on host:
# iperf -t 600 -c <device-ip-addr>
[ 28.396284] ------------[ cut here ]------------
[ 28.400912] kernel BUG at .../net/core/skbuff.c:1355!
[ 28.414019] Internal error: Oops - BUG: 0 [#1] SMP ARM
[ 28.419150] Modules linked in:
[ 28.422219] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G B 4.4.0+ #120
[ 28.429516] Hardware name: Rockchip (Device Tree)
[ 28.434216] task: c0665070 ti: c0660000 task.ti: c0660000
[ 28.439622] PC is at skb_put+0x10/0x54
[ 28.443381] LR is at arc_emac_poll+0x260/0x474
[ 28.447821] pc : [<c03af580>] lr : [<c028fec4>] psr: a0070113
[ 28.447821] sp : c0661e58 ip : eea68502 fp : ef377000
[ 28.459280] r10: 0000012c r9 : f08b2000 r8 : eeb57100
[ 28.464498] r7 : 00000000 r6 : ef376594 r5 : 00000077 r4 : ef376000
[ 28.471015] r3 : 0030488b r2 : ef13e880 r1 : 000005ee r0 : eeb57100
[ 28.477534] Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
[ 28.484658] Control: 10c5387d Table: 8eaf004a DAC: 00000051
[ 28.490396] Process swapper/0 (pid: 0, stack limit = 0xc0660210)
[ 28.496393] Stack: (0xc0661e58 to 0xc0662000)
[ 28.500745] 1e40: 00000002 00000000
[ 28.508913] 1e60: 00000000 ef376520 00000028 f08b23b8 00000000 ef376520 ef7b6900 c028fc64
[ 28.517082] 1e80: 2f158000 c0661ea8 c0661eb0 0000012c c065e900 c03bdeac ffff95e9 c0662100
[ 28.525250] 1ea0: c0663924 00000028 c0661ea8 c0661ea8 c0661eb0 c0661eb0 0000001e c0660000
[ 28.533417] 1ec0: 40000003 00000008 c0695a00 0000000a c066208c 00000100 c0661ee0 c0027410
[ 28.541584] 1ee0: ef0fb700 2f158000 00200000 ffff95e8 00000004 c0662100 c0662080 00000003
[ 28.549751] 1f00: 00000000 00000000 00000000 c065b45c 0000001e ef005000 c0647a30 00000000
[ 28.557919] 1f20: 00000000 c0027798 00000000 c005cf40 f0802100 c0662ffc c0661f60 f0803100
[ 28.566088] 1f40: c0661fb8 c00093bc c000ffb4 60070013 ffffffff c0661f94 c0661fb8 c00137d4
[ 28.574267] 1f60: 00000001 00000000 00000000 c001ffa0 00000000 c0660000 00000000 c065a364
[ 28.582441] 1f80: c0661fb8 c0647a30 00000000 00000000 00000000 c0661fb0 c000ffb0 c000ffb4
[ 28.590608] 1fa0: 60070013 ffffffff 00000051 00000000 00000000 c005496c c0662400 c061bc40
[ 28.598776] 1fc0: ffffffff ffffffff 00000000 c061b680 00000000 c0647a30 00000000 c0695294
[ 28.606943] 1fe0: c0662488 c0647a2c c066619c 6000406a 413fc090 6000807c 00000000 00000000
[ 28.615127] [<c03af580>] (skb_put) from [<ef376520>] (0xef376520)
[ 28.621218] Code: e5902054 e590c090 e3520000 0a000000 (e7f001f2)
[ 28.627307] ---[ end trace 4824734e2243fdb6 ]---
[ 34.377068] Internal error: Oops: 17 [#1] SMP ARM
[ 34.382854] Modules linked in:
[ 34.385947] CPU: 0 PID: 3 Comm: ksoftirqd/0 Not tainted 4.4.0+ #120
[ 34.392219] Hardware name: Rockchip (Device Tree)
[ 34.396937] task: ef02d040 ti: ef05c000 task.ti: ef05c000
[ 34.402376] PC is at __dev_kfree_skb_irq+0x4/0x80
[ 34.407121] LR is at arc_emac_poll+0x130/0x474
[ 34.411583] pc : [<c03bb640>] lr : [<c028fd94>] psr: 60030013
[ 34.411583] sp : ef05de68 ip : 0008e83c fp : ef377000
[ 34.423062] r10: c001bec4 r9 : 00000000 r8 : f08b24c8
[ 34.428296] r7 : f08b2400 r6 : 00000075 r5 : 00000019 r4 : ef376000
[ 34.434827] r3 : 00060000 r2 : 00000042 r1 : 00000001 r0 : 00000000
[ 34.441365] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
[ 34.448507] Control: 10c5387d Table: 8f25c04a DAC: 00000051
[ 34.454262] Process ksoftirqd/0 (pid: 3, stack limit = 0xef05c210)
[ 34.460449] Stack: (0xef05de68 to 0xef05e000)
[ 34.464827] de60: ef376000 c028fd94 00000000 c0669480 c0669480 ef376520
[ 34.473022] de80: 00000028 00000001 00002ae4 ef376520 ef7b6900 c028fc64 2f158000 ef05dec0
[ 34.481215] dea0: ef05dec8 0000012c c065e900 c03bdeac ffff983f c0662100 c0663924 00000028
[ 34.489409] dec0: ef05dec0 ef05dec0 ef05dec8 ef05dec8 ef7b6000 ef05c000 40000003 00000008
[ 34.497600] dee0: c0695a00 0000000a c066208c 00000100 ef05def8 c0027410 ef7b6000 40000000
[ 34.505795] df00: 04208040 ffff983e 00000004 c0662100 c0662080 00000003 ef05c000 ef027340
[ 34.513985] df20: ef05c000 c0666c2c 00000000 00000001 00000002 00000000 00000000 c0027568
[ 34.522176] df40: ef027340 c003ef48 ef027300 00000000 ef027340 c003edd4 00000000 00000000
[ 34.530367] df60: 00000000 c003c37c ffffff7f 00000001 00000000 ef027340 00000000 00030003
[ 34.538559] df80: ef05df80 ef05df80 00000000 00000000 ef05df90 ef05df90 ef05dfac ef027300
[ 34.546750] dfa0: c003c2a4 00000000 00000000 c000f578 00000000 00000000 00000000 00000000
[ 34.554939] dfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 34.563129] dfe0: 00000000 00000000 00000000 00000000 00000013 00000000 ffffffff dfff7fff
[ 34.571360] [<c03bb640>] (__dev_kfree_skb_irq) from [<c028fd94>] (arc_emac_poll+0x130/0x474)
[ 34.579840] [<c028fd94>] (arc_emac_poll) from [<c03bdeac>] (net_rx_action+0xdc/0x28c)
[ 34.587712] [<c03bdeac>] (net_rx_action) from [<c0027410>] (__do_softirq+0xcc/0x1f8)
[ 34.595482] [<c0027410>] (__do_softirq) from [<c0027568>] (run_ksoftirqd+0x2c/0x50)
[ 34.603168] [<c0027568>] (run_ksoftirqd) from [<c003ef48>] (smpboot_thread_fn+0x174/0x18c)
[ 34.611466] [<c003ef48>] (smpboot_thread_fn) from [<c003c37c>] (kthread+0xd8/0xec)
[ 34.619075] [<c003c37c>] (kthread) from [<c000f578>] (ret_from_fork+0x14/0x3c)
[ 34.626317] Code: e8bd8010 e3a00000 e12fff1e e92d4010 (e59030a4)
[ 34.632572] ---[ end trace cca5a3d86a82249a ]---
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch corrects the unaligned accesses seen on GRE TEB tunnels when
generating hash keys. Specifically what this patch does is make it so that
we force the use of skb_copy_bits when the GRE inner headers will be
unaligned due to NET_IP_ALIGNED being a non-zero value.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently our netdevice ops is a one static global variable which
is referenced by all mlx5e netdevice instances. This can be
problematic when different driver instances do not share same
HW capabilities (e.g SRIOV PF and VFs probed to the host).
Now we have two constant global netdevice ops variables, one
for basic netdevice ops and the other with extended SRIOV ops,
on netdevice construction we choose the one suitable for
current device capabilities.
Fixes: 66e49dedada6 ("net/mlx5e: Add support for SR-IOV ndos")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently mlx5e_select_queue is redundant since num_tc is always 1.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mlx5_ifc.h is a header file representing the API and ABI between
the driver to the firmware and hardware. This file is used from
both the mlx5_ib and mlx5_core drivers.
Previously, this file used incrementing counter to indicate
reserved fields, for example:
struct mlx5_ifc_odp_per_transport_service_cap_bits {
u8 send[0x1];
u8 receive[0x1];
u8 write[0x1];
u8 read[0x1];
u8 reserved_0[0x1];
u8 srq_receive[0x1];
u8 reserved_1[0x1a];
};
If one developer implements through net-next feature A that uses
reserved_0, they replace it with featureA and renames reserved_1 to
reserved_0. In the same kernel cycle, a 2nd developer could implement
feature B through the rdma tree, that uses reserved_1 and split it to
featureB and a smaller reserved_1 field. This will cause a conflict
when the two trees are merged.
The source of this conflict is that the 1st developer changed *all*
reserved fields.
As Linus suggested, we change the layout of structs to:
struct mlx5_ifc_odp_per_transport_service_cap_bits {
u8 send[0x1];
u8 receive[0x1];
u8 write[0x1];
u8 read[0x1];
u8 reserved_at_4[0x1];
u8 srq_receive[0x1];
u8 reserved_at_6[0x1a];
};
This makes the conflicts much more rare and preserves the locality of
changes.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Alaa Hleihel <alaa@mellanox.com>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is presently a race condition between the bonding periodic
link monitor and the updating of a slave's speed and duplex. The former
occurs on a periodic basis, and the latter in response to a driver's
calling of netif_carrier_on.
It is possible for the periodic monitor to run between the
driver call of netif_carrier_on and the receipt of the NETDEV_CHANGE
event that causes bonding to update the slave's speed and duplex. This
manifests most notably as a report that a slave is up and "0 Mbps full
duplex" after enslavement, but in principle could report an incorrect
speed and duplex after any link up event if the device comes up with a
different speed or duplex. This affects the 802.3ad aggregator
selection, as the speed and duplex are selection criteria.
This is fixed by updating the speed and duplex in the periodic
monitor, prior to using that information.
This was done historically in bonding, but the call to
bond_update_speed_duplex was removed in commit 876254ae2758 ("bonding:
don't call update_speed_duplex() under spinlocks"), as it might sleep
under lock. Later, the locking was changed to only hold RTNL, and so
after commit 876254ae2758 ("bonding: don't call update_speed_duplex()
under spinlocks") this call is again safe.
Tested-by: "Tantilov, Emil S" <emil.s.tantilov@intel.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: dingtianhong <dingtianhong@huawei.com>
Fixes: 876254ae2758 ("bonding: don't call update_speed_duplex() under spinlocks")
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Acked-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The am79c961a.c driver fails to build with clang because of an
unusual inline assembly construct:
drivers/net/ethernet/amd/am79c961a.c:53:7: error: invalid % escape in inline assembly string
"str%?h %1, [%2] @ NET_RAP\n\t"
The same change has been done a decade ago in arch/arm as of
6a39dd6222dd ("[ARM] 3759/2: Remove uses of %?"), but apparently
some drivers were missed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The smc91x driver doesn't honor the probe deferral mechanism when the
interrupt source is not yet available, such as one provided by a gpio
controller not probed.
Fix this by propagating the platform_get_irq() error code as the probe
return value.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the two wildcard entries, they serve no purpose and will match way too
many devices, some of them being covered by the driver in
drivers/net/phy/broadcom.c. Remove the now unused bcm7xxx_dummy_config_init()
function which would produce a warning.
Fixes: b560a58c45c6 ("net: phy: add Broadcom BCM7xxx internal PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since we were wrongly advertising gigabit features for these 10/100 only
Ethernet PHYs, bcm7xxx_config_init() which is supposed to apply workaround
would have not run since the check would be true, now that we have fixed the
PHY features, remove that check since it has no reasoning to be there anymore.
Fixes: e18556ee3bd83 ("net: phy: bcm7xxx: do not use PHY_BRCM_100MBPS_WAR")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The PHY entries for BCM7425/29/35 declare the 40nm Ethernet PHY as being
10/100/1000 capable, while this is just a 10/100 capable PHY device, fix that.
Fixes: d068b02cfdfc2 ("net: phy: add BCM7425 and BCM7429 PHYs")
Fixes: 9458ceab4917 ("net: phy: bcm7xxx: Add entry for BCM7435")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The clear and set masks in the call to phy_set_clr_bits() called from
bcm7xxx_config_init() are inverted. We need to fix this by swapping the two
arguments, that is, set 0 bits, but clear the shade mode 2 enable bit.
Fixes: b560a58c45c66 ("net: phy: add Broadcom BCM7xxx internal PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When adding support for the R-Car gen3 gPTP active in configuration mode,
some call sites of ravb_ptp_{init|stop}() were missed due to an oversight.
Add checks for the R-Car gen2 SoCs around these...
Fixes: f5d7837f96e5 ("ravb: ptp: Add CONFIG mode support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When adding support for the R-Car gen3 gPTP active in configuration mode,
the code setting the CCC.CSEL field was duplicated due to an oversight.
For R-Car gen 2 it's just redundant and for R-Car gen3 the write at this
time is probably ignored due to CCC.GAC bit being already set...
Fixes: f5d7837f96e5 ("ravb: ptp: Add CONFIG mode support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The unix_dgram_sendmsg routine use the following test
if (unlikely(unix_peer(other) != sk && unix_recvq_full(other))) {
to determine if sk and other are in an n:1 association (either
established via connect or by using sendto to send messages to an
unrelated socket identified by address). This isn't correct as the
specified address could have been bound to the sending socket itself or
because this socket could have been connected to itself by the time of
the unix_peer_get but disconnected before the unix_state_lock(other). In
both cases, the if-block would be entered despite other == sk which
might either block the sender unintentionally or lead to trying to unlock
the same spin lock twice for a non-blocking send. Add a other != sk
check to guard against this.
Fixes: 7d267278a9ec ("unix: avoid use-after-free in ep_remove_wait_queue")
Reported-By: Philipp Hahn <pmhahn@pmhahn.de>
Signed-off-by: Rainer Weikusat <rweikusat@mobileactivedefense.com>
Tested-by: Philipp Hahn <pmhahn@pmhahn.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The present unix_stream_read_generic contains various code sequences of
the form
err = -EDISASTER;
if (<test>)
goto out;
This has the unfortunate side effect of possibly causing the error code
to bleed through to the final
out:
return copied ? : err;
and then to be wrongly returned if no data was copied because the caller
didn't supply a data buffer, as demonstrated by the program available at
http://pad.lv/1540731
Change it such that err is only set if an error condition was detected.
Fixes: 3822b5c2fc62 ("af_unix: Revert 'lock_interruptible' in stream receive code")
Reported-by: Joseph Salisbury <joseph.salisbury@canonical.com>
Signed-off-by: Rainer Weikusat <rweikusat@mobileactivedefense.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
batman-adv checks in different situation if a new device is already on top
of a different batman-adv device. This is done by getting the iflink of a
device and all its parent. It assumes that this iflink is always a parent
device in an acyclic graph. But this assumption is broken by devices like
veth which are actually a pair of two devices linked to each other. The
recursive check would therefore get veth0 when calling dev_get_iflink on
veth1. And it gets veth0 when calling dev_get_iflink with veth1.
Creating a veth pair and loading batman-adv freezes parts of the system
ip link add veth0 type veth peer name veth1
modprobe batman-adv
An RCU stall will be detected on the system which cannot be fixed.
INFO: rcu_sched self-detected stall on CPU
1: (5264 ticks this GP) idle=3e9/140000000000001/0
softirq=144683/144686 fqs=5249
(t=5250 jiffies g=46 c=45 q=43)
Task dump for CPU 1:
insmod R running task 0 247 245 0x00000008
ffffffff8151f140 ffffffff8107888e ffff88000fd141c0 ffffffff8151f140
0000000000000000 ffffffff81552df0 ffffffff8107b420 0000000000000001
ffff88000e3fa700 ffffffff81540b00 ffffffff8107d667 0000000000000001
Call Trace:
<IRQ> [<ffffffff8107888e>] ? rcu_dump_cpu_stacks+0x7e/0xd0
[<ffffffff8107b420>] ? rcu_check_callbacks+0x3f0/0x6b0
[<ffffffff8107d667>] ? hrtimer_run_queues+0x47/0x180
[<ffffffff8107cf9d>] ? update_process_times+0x2d/0x50
[<ffffffff810873fb>] ? tick_handle_periodic+0x1b/0x60
[<ffffffff810290ae>] ? smp_trace_apic_timer_interrupt+0x5e/0x90
[<ffffffff813bbae2>] ? apic_timer_interrupt+0x82/0x90
<EOI> [<ffffffff812c3fd7>] ? __dev_get_by_index+0x37/0x40
[<ffffffffa0031f3e>] ? batadv_hard_if_event+0xee/0x3a0 [batman_adv]
[<ffffffff812c5801>] ? register_netdevice_notifier+0x81/0x1a0
[...]
This can be avoided by checking if two devices are each others parent and
stopping the check in this situation.
Fixes: b7eddd0b3950 ("batman-adv: prevent using any virtual device created on batman-adv as hard-interface")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[sven@narfation.org: rewritten description, extracted fix]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
|
|
The batadv_orig_node_vlan reference counter in batadv_tt_global_size_mod
can only be reduced when the list entry was actually removed. Otherwise the
reference counter may reach zero when batadv_tt_global_size_mod is called
from two different contexts for the same orig_node_vlan but only one
context is actually removing the entry from the list.
The release function for this orig_node_vlan is not called inside the
vlan_list_lock spinlock protected region because the function
batadv_tt_global_size_mod still holds a orig_node_vlan reference for the
object pointer on the stack. Thus the actual release function (when
required) will be called only at the end of the function.
Fixes: 7ea7b4a14275 ("batman-adv: make the TT CRC logic VLAN specific")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
|
|
The batadv_gw_node reference counter in batadv_gw_node_update can only be
reduced when the list entry was actually removed. Otherwise the reference
counter may reach zero when batadv_gw_node_update is called from two
different contexts for the same gw_node but only one context is actually
removing the entry from the list.
The release function for this gw_node is not called inside the list_lock
spinlock protected region because the function batadv_gw_node_update still
holds a gw_node reference for the object pointer on the stack. Thus the
actual release function (when required) will be called only at the end of
the function.
Fixes: bd3524c14bd0 ("batman-adv: remove obsolete deleted attribute for gateway node")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
|
|
The iwl_trans_pcie_start_fw() function may return the positive value EIO
instead of -EIO in case of error.
Signed-off-by: Anton Protopopov <a.s.protopopov@gmail.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
When we load the firmware, we hold trans_pcie->mutex to
avoid nested flows. We also rely on the ISR to wake up the
thread when the DMA has finished copying a chunk. During
this flow, we enable the RF-Kill interrupt.
The problem is that the RF-Kill interrupt handler can take
the mutex and bring the device down. This means that if
we load the firmware while the RF-Kill switch is enabled
(which will happen when we load the INIT firmware to read
the device's capabilities and register to mac80211), we
may get an RF-Kill interrupt immediately and the ISR will
be waiting for the mutex held by the thread that is
currently loading the firmware. At this stage, the ISR
won't be able to service the DMA's interrupt needed to
wake up the thread that load the firmware. We are in a
deadlock situation which ends when the thread that loads
the firmware fails on timeout and releases the mutex.
To fix this, take the mutex later in the flow, disable
the interrupts and synchronize_irq() to give a chance to
the RF-Kill interrupt to run and complete.
After that, mask all the interrupts besides the DMA
interrupt and proceed with firmware load. Make sure to
check that there was no RF-Kill interrupt when the
interrupts were disabled.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=111361
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
The firmware can perform a scheduled scan with not matchsets passed,
but it can't send notification that results were found. Since the
userspace then cannot know when we got new results and the firmware
wouldn't trigger a wake in case we are sleeping, it's better not to
allow scans without matchsets.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=110831
Cc: <stable@vger.kernel.org> [3.17+]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
My analysis in the below mail applies, although the second part is
unnecessary because i isn't used in arithmetic operations here:
https://marc.info/?l=openbsd-tech&m=145377854103866&w=2
Thanks for your time.
Signed-off-by: Michael McConville <mmcco@mykolab.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
BRIDGE_VLAN_FILTERING automatically adds a newly bridged port to the
VLAN with the bridge's default_pvid.
The mv88e6xxx driver currently reserves VLANs 4000+ for unbridged ports
isolation. When a port joins a bridge, it leaves its reserved VLAN. When
a port leaves a bridge, it joins again its reserved VLAN.
But if the VLAN filtering is disabled, or if this hardware VLAN is
already in use, the bridged port ends up with no default VLAN, and the
communication with the CPU is thus broken.
To fix this, make a port join its reserved VLAN once on setup, never
leave it, and restore its PVID after another one was eventually used.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current bridge code calls switchdev_port_obj_del on a VLAN port even
if the corresponding switchdev_port_obj_add call returned -EOPNOTSUPP.
If the DSA driver doesn't return -EOPNOTSUPP for a software port VLAN in
its port_vlan_del function, the VLAN is not deleted. Unbridging the port
also generates a stack trace for the same reason.
This can be quickly tested on a VLAN filtering enabled system with:
# brctl addbr br0
# brctl addif br0 lan0
# brctl addbr br1
# brctl addif br1 lan1
# brctl delif br1 lan1
Both bridges have a default default_pvid set to 1. lan0 uses the
hardware VLAN 1 while lan1 falls back to the software VLAN 1.
Unbridging lan1 does not delete its software VLAN, and thus generates
the following stack trace:
[ 2991.681705] device lan1 left promiscuous mode
[ 2991.686237] br1: port 1(lan1) entered disabled state
[ 2991.725094] ------------[ cut here ]------------
[ 2991.729761] WARNING: CPU: 0 PID: 869 at net/bridge/br_vlan.c:314 __vlan_group_free+0x4c/0x50()
[ 2991.738437] Modules linked in:
[ 2991.741546] CPU: 0 PID: 869 Comm: ip Not tainted 4.4.0 #16
[ 2991.747039] Hardware name: Freescale Vybrid VF5xx/VF6xx (Device Tree)
[ 2991.753511] Backtrace:
[ 2991.756008] [<80014450>] (dump_backtrace) from [<8001469c>] (show_stack+0x20/0x24)
[ 2991.763604] r6:80512644 r5:00000009 r4:00000000 r3:00000000
[ 2991.769343] [<8001467c>] (show_stack) from [<80268e44>] (dump_stack+0x24/0x28)
[ 2991.776618] [<80268e20>] (dump_stack) from [<80025568>] (warn_slowpath_common+0x98/0xc4)
[ 2991.784750] [<800254d0>] (warn_slowpath_common) from [<80025650>] (warn_slowpath_null+0x2c/0x34)
[ 2991.793557] r8:00000000 r7:9f786a8c r6:9f76c440 r5:9f786a00 r4:9f68ac00
[ 2991.800366] [<80025624>] (warn_slowpath_null) from [<80512644>] (__vlan_group_free+0x4c/0x50)
[ 2991.808946] [<805125f8>] (__vlan_group_free) from [<80514488>] (nbp_vlan_flush+0x44/0x68)
[ 2991.817147] r4:9f68ac00 r3:9ec70000
[ 2991.820772] [<80514444>] (nbp_vlan_flush) from [<80506f08>] (del_nbp+0xac/0x130)
[ 2991.828201] r5:9f56f800 r4:9f786a00
[ 2991.831841] [<80506e5c>] (del_nbp) from [<8050774c>] (br_del_if+0x40/0xbc)
[ 2991.838724] r7:80590f68 r6:00000000 r5:9ec71c38 r4:9f76c440
[ 2991.844475] [<8050770c>] (br_del_if) from [<80503dc0>] (br_del_slave+0x1c/0x20)
[ 2991.851802] r5:9ec71c38 r4:9f56f800
[ 2991.855428] [<80503da4>] (br_del_slave) from [<80484a34>] (do_setlink+0x324/0x7b8)
[ 2991.863043] [<80484710>] (do_setlink) from [<80485e90>] (rtnl_newlink+0x508/0x6f4)
[ 2991.870616] r10:00000000 r9:9ec71ba8 r8:00000000 r7:00000000 r6:9f6b0400 r5:9f56f800
[ 2991.878548] r4:8076278c
[ 2991.881110] [<80485988>] (rtnl_newlink) from [<80484048>] (rtnetlink_rcv_msg+0x18c/0x22c)
[ 2991.889315] r10:9f7d4e40 r9:00000000 r8:00000000 r7:00000000 r6:9f7d4e40 r5:9f6b0400
[ 2991.897250] r4:00000000
[ 2991.899814] [<80483ebc>] (rtnetlink_rcv_msg) from [<80497c74>] (netlink_rcv_skb+0xb0/0xcc)
[ 2991.908104] r8:00000000 r7:9f7d4e40 r6:9f7d4e40 r5:80483ebc r4:9f6b0400
[ 2991.914928] [<80497bc4>] (netlink_rcv_skb) from [<80483eb4>] (rtnetlink_rcv+0x34/0x3c)
[ 2991.922874] r6:9f5ea000 r5:00000028 r4:9f7d4e40 r3:80483e80
[ 2991.928622] [<80483e80>] (rtnetlink_rcv) from [<80497604>] (netlink_unicast+0x180/0x200)
[ 2991.936742] r4:9f4edc00 r3:80483e80
[ 2991.940362] [<80497484>] (netlink_unicast) from [<80497a88>] (netlink_sendmsg+0x33c/0x350)
[ 2991.948648] r8:00000000 r7:00000028 r6:00000000 r5:9f5ea000 r4:9ec71f4c
[ 2991.955481] [<8049774c>] (netlink_sendmsg) from [<80457ff0>] (sock_sendmsg+0x24/0x34)
[ 2991.963342] r10:00000000 r9:9ec71e28 r8:00000000 r7:9f1e2140 r6:00000000 r5:00000000
[ 2991.971276] r4:9ec71f4c
[ 2991.973849] [<80457fcc>] (sock_sendmsg) from [<80458af0>] (___sys_sendmsg+0x1fc/0x204)
[ 2991.981809] [<804588f4>] (___sys_sendmsg) from [<804598d0>] (__sys_sendmsg+0x4c/0x7c)
[ 2991.989640] r10:00000000 r9:9ec70000 r8:80010824 r7:00000128 r6:7ee946c4 r5:00000000
[ 2991.997572] r4:9f1e2140
[ 2992.000128] [<80459884>] (__sys_sendmsg) from [<80459918>] (SyS_sendmsg+0x18/0x1c)
[ 2992.007725] r6:00000000 r5:7ee9c7b8 r4:7ee946e0
[ 2992.012430] [<80459900>] (SyS_sendmsg) from [<80010660>] (ret_fast_syscall+0x0/0x3c)
[ 2992.020182] ---[ end trace 5d4bc29f4da04280 ]---
To fix this, return -EOPNOTSUPP in _mv88e6xxx_port_vlan_del instead of
-ENOENT if the hardware VLAN doesn't exist or the port is not a member.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
smatch detected a suspicious looking bitop condition:
drivers/net/ethernet/cavium/liquidio/lio_main.c:2529
handle_timestamp() warn: suspicious bitop condition
(skb_shinfo(skb)->tx_flags | SKBTX_IN_PROGRESS is always non-zero,
so the logic is definitely not correct. Use & to mask the correct
bit.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit c0eb454034aa ("hv_netvsc: Don't ask for additional head room in the
skb") got rid of needed_headroom setting for the driver. With the change I
hit the following issue trying to use ptkgen module:
[ 57.522021] kernel BUG at net/core/skbuff.c:1128!
[ 57.522021] invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC
...
[ 58.721068] Call Trace:
[ 58.721068] [<ffffffffa0144e86>] netvsc_start_xmit+0x4c6/0x8e0 [hv_netvsc]
...
[ 58.721068] [<ffffffffa02f87fc>] ? pktgen_finalize_skb+0x25c/0x2a0 [pktgen]
[ 58.721068] [<ffffffff814f5760>] ? __netdev_alloc_skb+0xc0/0x100
[ 58.721068] [<ffffffffa02f9907>] pktgen_thread_worker+0x257/0x1920 [pktgen]
Basically, we're calling skb_cow_head(skb, RNDIS_AND_PPI_SIZE) and crash on
if (skb_shared(skb))
BUG();
We probably need to restore needed_headroom setting (but shrunk to
RNDIS_AND_PPI_SIZE as we don't need more) to request the required headroom
space. In theory, it should not give us performance penalty.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When stopping the port, the CPU notifier are still there whereas the
mvneta_stop_dev function calls mvneta_percpu_disable() on each CPUs.
It was possible to have a new CPU coming at this point which could be
racy.
This patch adds a flag preventing executing the code notifier for a new
CPU when the port is stopping. It also uses the spinlock introduces
previously. To avoid the deadlock, the lock has been moved outside the
mvneta_percpu_elect function.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Electing a CPU must be done in an atomic way: it should be done after or
before the removal/insertion of a CPU and this function is not reentrant.
During the loop of mvneta_percpu_elect we associates the queues to the
CPUs, if there is a topology change during this loop, then the mapping
between the CPUs and the queues could be wrong. During this loop the
interrupt mask is also updating for each CPUs, It should not be changed
in the same time by other part of the driver.
This patch adds spinlock to create the needed critical sections.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the MVNETA_INTR_* registers, the queues related fields are per cpu,
according to the datasheet (comment in [] are added by me):
"In a multi-CPU system, bits of RX[or TX] queues for which the access by
the reading[or writing] CPU is disabled are read as 0, and cannot be
cleared[or written]."
That means that each time we want to manipulate these bits we had to do
it on each cpu and not only on the current cpu.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Daniel Jurgens
Eran Ben Elisha
Eugenia Emantayev
Amir Vadai
Bjørn Mork
Eric Dumazet
Ken Kawasaki
Sascha Hauer
Jon Paul Maloy
Michael Chan
Arnd Bergmann
Hariprasad Shenai
Alexander Kochetkov
Alexander Duyck
Saeed Mahameed
Matan Barak
Jay Vosburgh
Robert Jarzmik
Florian Fainelli
Sergei Shtylyov
Rainer Weikusat
Andrew Lunn
Sven Eckelmann
Anton Protopopov
Emmanuel Grumbach
Luca Coelho
Michael McConville
Vivien Didelot
Colin Ian King
Vitaly Kuznetsov
Gregory CLEMENT