| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
In Samsung devices, the method used to compensate for temperature,
age, load etc is by way of VBAT to Ri tables, which correlates the
battery voltage under load (VBAT) to an internal resistance (Ri).
Using this Ri and a measurement of the current out of the battery
(IBAT) the open circuit voltage (OCV) can be calculated as:
OCV = VBAT - (Ri * IBAT)
The details are described in comments to struct
power_supply_battery_info in the commit.
Since not all batteries supply this VBAT-to-Ri data, the fallback
method to use the temperature-to-Ri lookup table can also be used
as a fallback.
Add two helper functions to check if we have the tables needed for
using power_supply_vbat2ri() or power_supply_temp2resist_simple()
respectively, so capacity estimation code can choose which one
to employ.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The Battery Type Indicator (BTI) resistor is a resistor mounted
between a special terminal on the battery and ground. By sending
a fixed current (such as 7mA) through this resistor and measuring
the voltage over it, the resistance can be determined, and this
verifies the battery type.
Typical side view of the battery:
o o o
GND BTI +3.8V
Typical example of the electrical layout:
+3.8 V BTI
| |
| + |
_______ [ ] 7kOhm
___ |
| |
| |
GND GND
By verifying this resistance before attempting to charge the
battery we add an additional level of security.
In some systems this is used for plug-and-play of batteries with
different capacity. In other cases, this is merely used to verify
that the right type of battery is connected, if several batteries
have the same physical shape and can be plugged into the same
slot. Sometimes this is just a surplus security mechanism.
Nokia and Samsung among many other vendors are known to use these
BTI resistors.
Add the BTI properties to struct power_supply_battery_info and
switch the AB8500 charger code over to using it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The AB8500 code is using a special current and voltage setting
when the battery is in "alert mode", i.e. when it is starting
to go outside normal operating conditions so it is too
cold or too hot. This makes sense as a way for the charging
algorithm to deal with hostile environments.
Add the needed members to the struct power_supply_battery_info,
and switch the AB8500 charging code over to using this.
Reviewed-by: Matti Vaittineen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Maintenance charging is the phase of keeping up the charge
after the battery has charged fully using CC/CV charging.
This can be done in many successive phases and is usually
done with a slightly lower constant voltage than CV, and
a slightly lower allowed current.
Add an array of maintenance charging points each with a
current, voltage and safety timer, and add helper functions
to use these. Migrate the AB8500 code over.
This is used in several Samsung products using the AB8500
and these batteries and their complete parameters will
be added later as full examples, but the default battery
in the AB8500 code serves as a reasonable example so far.
Reviewed-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Adds a POWER_SUPPLY_CHARGE_TYPE_BYPASS option to the POWER_SUPPLY_PROP_CHARGE_TYPE
property to facilitate bypass charging operation.
In bypass charging operation, the charger bypasses the charging path around the
integrated converter allowing for a "smart" wall adaptor to perform the power
conversion externally.
This operational mode is critical for the USB PPS standard of power adaptors and is
becoming a common feature in modern charging ICs such as:
- BQ25980
- BQ25975
- BQ25960
- LN8000
- LN8410
Signed-off-by: Ricardo Rivera-Matos <rriveram@opensource.cirrus.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Some (USB) charger ICs have variants with USB D+ and D- pins to do their
own builtin charger-type detection, like e.g. the bq24190 and bq25890 and
also variants which lack this functionality, e.g. the bq24192 and bq25892.
In case the charger-type; and thus the input-current-limit detection is
done outside the charger IC then we need some way to communicate this to
the charger IC. In the past extcon was used for this, but if the external
detection does e.g. full USB PD negotiation then the extcon cable-types do
not convey enough information.
For these setups it was decided to model the external charging "brick"
and the parameters negotiated with it as a power_supply class-device
itself; and power_supply_set_input_current_limit_from_supplier() was
introduced to allow drivers to get the input-current-limit this way.
But in some cases psy drivers may want to know other properties, e.g. the
bq25892 can do "quick-charge" negotiation by pulsing its current draw,
but this should only be done if the usb_type psy-property of its supplier
is set to DCP (and device-properties indicate the board allows higher
voltages).
Instead of adding extra helper functions for each property which
a psy-driver wants to query from its supplier, refactor
power_supply_set_input_current_limit_from_supplier() into a
more generic power_supply_get_property_from_supplier() function.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Pull x86 platform driver updates from Hans de Goede:
"Highlights:
New drivers:
- asus-tf103c-dock
- intel_crystal_cove_charger
- lenovo-yogabook-wmi
- simatic-ipc platform-code + led driver + watchdog driver
- x86-android-tablets (kernel module to workaround DSDT bugs on
these)
amd-pmc:
- bug-fixes
- smar trace buffer support
asus-wmi:
- support for custom fan curves
int3472 (camera info ACPI object for Intel IPU3/SkyCam cameras):
- ACPI core + int3472 changes to delay enumeration of camera sensor
I2C clients until the PMIC for the sensor has been fully probed
- Add support for board data (DSDT info is incomplete) for setting up
the tps68470 PMIC used on some boards with these cameras
- Add board data for the Microsoft Surface Go (original, v2 and v3)
thinkpad_acpi:
- various cleanups
- support for forced battery discharging (for battery calibration)
- support to inhibit battery charging
- this includes power_supply core changes to add new APIs for this
think_lmi:
- enhanced BIOS password support
various other small fixes and hardware-id additions"
* tag 'platform-drivers-x86-v5.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (78 commits)
power: supply: Provide stubs for charge_behaviour helpers
platform/x86: x86-android-tablets: Fix GPIO lookup leak on error-exit
platform/x86: int3472: Add board data for Surface Go 3
platform/x86: Add Asus TF103C dock driver
platform/x86: x86-android-tablets: Add TM800A550L data
platform/x86: x86-android-tablets: Add Asus MeMO Pad 7 ME176C data
platform/x86: x86-android-tablets: Add Asus TF103C data
platform/x86: x86-android-tablets: Add support for preloading modules
platform/x86: x86-android-tablets: Add support for registering GPIO lookup tables
platform/x86: x86-android-tablets: Add support for instantiating serdevs
platform/x86: x86-android-tablets: Add support for instantiating platform-devs
platform/x86: x86-android-tablets: Add support for PMIC interrupts
platform/x86: x86-android-tablets: Don't return -EPROBE_DEFER from a non probe() function
platform/x86: touchscreen_dmi: Remove the Glavey TM800A550L entry
platform/x86: touchscreen_dmi: Enable pen support on the Chuwi Hi10 Plus and Pro
platform/x86: touchscreen_dmi: Correct min/max values for Chuwi Hi10 Pro (CWI529) tablet
platform/x86: Add intel_crystal_cove_charger driver
power: supply: fix charge_behaviour attribute initialization
platform/x86: intel-uncore-frequency: use default_groups in kobj_type
x86/platform/uv: use default_groups in kobj_type
...
|
|
When CONFIG_SYSFS is not enabled provide stubs for the helper functions
to not break their callers.
Fixes: 539b9c94ac83 ("power: supply: add helpers for charge_behaviour sysfs")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20220108153158.189489-1-linux@weissschuh.net
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The function to retrieve battery info (from the device tree) assumes
we have a static info struct that gets populated by calling into
power_supply_get_battery_info().
This is awkward since I want to support tables of static battery
info by just assigning a pointer to all info based on e.g. a
compatible value in the device tree.
We also have a mixture of static and dynamically allocated
variables here.
Bite the bullet and let power_supply_get_battery_info() allocate
also the memory used for the very top level
struct power_supply_battery_info container. Pass pointers
around and lifecycle this with the psy device just like the
stuff we allocate inside it.
Change all current users over.
As part of the change, initializers need to be added to some
previously uninitialized fields in struct
power_supply_battery_info.
Reviewed-By: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
These helper functions can be used by drivers to implement their own
sysfs-attributes.
This is useful for ACPI-drivers extending the default ACPI-battery with
their own charge_behaviour attributes.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20211123232704.25394-3-linux@weissschuh.net
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
This a revised version of
"[RFC] add standardized attributes for force_discharge and inhibit_charge" [0],
incorporating discussion results.
The biggest change is the switch from two boolean attributes to a single
enum attribute.
[0] https://lore.kernel.org/platform-driver-x86/21569a89-8303-8573-05fb-c2fec29983d1@gmail.com/
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20211123232704.25394-2-linux@weissschuh.net
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
This complements the struct power_supply_battery_info with
extensive kerneldoc explaining the different semantics of the
fields, including an overview of the CC/CV charging concepts
implicit in some of the struct members.
This is done to first establish semantics before I can
add more charging methods by breaking out the CC/CV parameters
to its own struct.
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Some chargers can keep the system powered from the mains even when no
battery is present. It this case none of the currently defined health
statuses applies. Add a new status to report that no battery is present.
Suggested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
This extends the struct power_supply_battery_info with a
"technology" field makes the core DT parser optionally obtain
this from the device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Pull power supply and reset updates from Sebastian Reichel:
"battery/charger driver changes:
- core:
- provide function stubs if CONFIG_POWER_SUPPLY=n
- reduce loglevel for probe defer info
- surface:
- new battery and charger drivers for Surface
- bq27xxx:
- add bq78z100 support
- fix current_now/power_avg for newer chips
- cw2015:
- add CHARGE_NOW support
- ab8500:
- drop pdata support
- convert most DT bindings to YAML
- lots of minor fixes and cleanups
reset drivers:
- ltc2952-poweroff:
- make trigger delay configurable from DT
- minor fixes and cleanups"
* tag 'for-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (97 commits)
power: supply: cpcap-battery: fix invalid usage of list cursor
power: supply: bq256xx: add kerneldoc for structure members
power: supply: act8945a: correct kerneldoc
power: supply: max17040: remove unneeded double cast
power: supply: max17040: handle device_property_read_u8_array() failure
power: supply: max14577: remove unneeded variable initialization
power: supply: surface-charger: Make symbol 'surface_ac_pm_ops' static
power: supply: surface-battery: Make some symbols static
power: reset: restart-poweroff: Add missing MODULE_DEVICE_TABLE
power: reset: hisi-reboot: add missing MODULE_DEVICE_TABLE
power: supply: s3c_adc_battery: fix possible use-after-free in s3c_adc_bat_remove()
power: supply: generic-adc-battery: fix possible use-after-free in gab_remove()
power: supply: Add AC driver for Surface Aggregator Module
power: supply: Add battery driver for Surface Aggregator Module
power: supply: bq25980: Move props from battery node
power: supply: core: Use true and false for bool variable
power: supply: goldfish: Remove the GOLDFISH dependency
power: reset: ltc2952: make trigger delay configurable
power: supply: cpcap-charger: Simplify bool conversion
power: supply: cpcap-charger: Add usleep to cpcap charger to avoid usb plug bounce
...
|
|
Fix the following coccicheck warning:
./include/linux/power_supply.h:507:9-10: WARNING: return of 0/1 in
function 'power_supply_is_watt_property' with return type bool.
./include/linux/power_supply.h:479:9-10: WARNING: return of 0/1 in
function 'power_supply_is_amp_property' with return type bool.
Reported-by: Abaci Robot<abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The build error happens when CONFIG_POWER_SUPPLY is not enabled.
h8300-linux-ld: drivers/usb/dwc3/gadget.o: in function `.L59':
>> gadget.c:(.text+0x655): undefined reference to `power_supply_set_property'
Fixes: 99288de36020 ("usb: dwc3: add an alternate path in vbus_draw callback")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ray Chi <raychi@google.com>
Link: https://lore.kernel.org/r/20210327182809.1814480-3-raychi@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix build error when CONFIG_POWER_SUPPLY is not enabled.
The build error occurs in mips (cavium_octeon_defconfig).
mips-linux-gnu-ld: drivers/usb/dwc3/core.o: in function `dwc3_remove':
drivers/usb/dwc3/core.c:1657: undefined reference to `power_supply_put'
mips-linux-gnu-ld: drivers/usb/dwc3/core.o: in function `dwc3_get_properties':
drivers/usb/dwc3/core.c:1270: undefined reference to `power_supply_get_by_name'
mips-linux-gnu-ld: drivers/usb/dwc3/core.o: in function `dwc3_probe':
drivers/usb/dwc3/core.c:1632: undefined reference to `power_supply_put'
Fixes: 59fa3def35de ("usb: dwc3: add a power supply for current control")
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Ray Chi <raychi@google.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Currently, power_supply framework supports only Battery, UPS,
Mains and USB power_supply_type. Add wireless power_supply_type
so that the drivers which supports wireless can register a power
supply class device with POWER_SUPPLY_TYPE_WIRELESS.
Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
Signed-off-by: Guru Das Srinagesh <gurus@codeaurora.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The generic battery temperature properties are already supported by the
power-supply core. Let's support parsing of the common battery temperature
properties from a device-tree.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
This is a long life mode set in the factory for extended warranty
battery, the power charging rate is customized so that battery at
work last longer.
Presently switching to a different battery charging mode is through
EC PID 0x0710 to configure the battery firmware, this operation will
be blocked by EC with failure code 0x01 when PLL mode is already
in use.
Signed-off-by: Crag Wang <crag.wang@dell.com>
Reviewed-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Add HEALTH_WARM, HEALTH_COOL and HEALTH_HOT to the health enum.
HEALTH_WARM, HEALTH_COOL, and HEALTH_HOT properties are taken
from JEITA specification JISC8712:2015
Acked-by: Andrew F. Davis <afd@ti.com>
Tested-by: Guru Das Srinagesh <gurus@codeaurora.org>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Some battery fuel gauges know when the battery needs to
be recalibrated before providing usable values. This
should be reported via the health property.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Some smart batteries store their manufacture date, which is
useful to identify the battery and/or to know about the cell
quality.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Add a property for reporting the error margin expected
by fuel gauge chips.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Add parsing of new device-tree battery bindings.
- trickle-charge-current-microamp
- precharge-upper-limit-microvolt
- re-charge-voltage-microvolt
- over-voltage-threshold-microvolt
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Since tables pointed to by power_supply_desc->properties and
->usb_types are not expected to change after registration, mark
the pointers accordingly
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Since the battery internal resistance can be changed with the temperature
changes, thus add a resistance temperature table support to look up
the accurate battery internal resistance in a certain temperature.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Pull power supply and reset updates from Sebastian Reichel:
"Core:
- add HWMON compat layer
- new properties:
- input power limit
- input voltage limit
Drivers:
- qcom-pon: add gen2 support
- new driver for storing reboot move in NVMEM
- new driver for Wilco EC charger configuration
- simplify getting the adapter of a client"
* tag 'for-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply:
power: reset: nvmem-reboot-mode: add CONFIG_OF dependency
power_supply: wilco_ec: Add charging config driver
power: supply: cros: allow to set input voltage and current limit
power: supply: add input power and voltage limit properties
power: supply: fix semicolon.cocci warnings
power: reset: nvmem-reboot-mode: use NVMEM as reboot mode write interface
dt-bindings: power: reset: add document for NVMEM based reboot-mode
reset: qcom-pon: Add support for gen2 pon
dt-bindings: power: reset: qcom: Add qcom,pm8998-pon compatibility line
power: supply: Add HWMON compatibility layer
power: supply: sbs-manager: simplify getting the adapter of a client
power: supply: rt9455_charger: simplify getting the adapter of a client
power: supply: rt5033_battery: simplify getting the adapter of a client
power: supply: max17042_battery: simplify getting the adapter of a client
power: supply: max17040_battery: simplify getting the adapter of a client
power: supply: max14656_charger_detector: simplify getting the adapter of a client
power: supply: bq25890_charger: simplify getting the adapter of a client
power: supply: bq24257_charger: simplify getting the adapter of a client
power: supply: bq24190_charger: simplify getting the adapter of a client
|
|
For thermal management strategy you might be interested on limit the
input power for a power supply. We already have current limit but
basically what we probably want is to limit power. So, introduce the
input_power_limit property.
Although the common use case is limit the input power, in some
specific cases it is the voltage that is problematic (i.e some regulators
have different efficiencies at higher voltage resulting in more heat).
So introduce also the input_voltage_limit property.
This happens in one Chromebook and is used on the Pixel C's thermal
management strategy to effectively limit the input power to 5V 3A when
the screen is on. When the screen is on, the display, the CPU, and the GPU
all contribute more heat to the system than while the screen is off, and
we made a tradeoff to throttle the charger in order to give more of the
thermal budget to those other components.
So there's nothing fundamentally broken about the hardware that would
cause the Pixel C to malfunction if we were charging at 9V or 12V instead
of 5V when the screen is on, i.e. if userspace doesn't change this.
What would happen is that you wouldn't meet Google's skin temperature
targets on the system if the charger was allowed to run at 9V or 12V with
the screen on.
For folks hacking on Pixel Cs (which is now outside of Google's official
support window for Android) and customizing their own kernel and userspace
this would be acceptable, but we wanted to expose this feature in the
power supply properties because the feature does exist in the Emedded
Controller firmware of the Pixel C and all of Google's Chromebooks with
USB-C made since 2015 in case someone running an up to date kernel wanted
to limit the charging power for thermal or other reasons.
This patch exposes a new property, similar to input current limit, to
re-configure the maximum voltage from the external supply at runtime
based on system-level knowledge or user input.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Add code implementing HWMON adapter/compatibility layer to allow
expositing various sensors present on power supply devices via HWMON
subsystem. This is done in order to allow userspace to use single
ABI/library(libsensors) to access/manipulate all of the sensors of the
system.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Chris Healy <cphealy@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Based on 1 normalized pattern(s):
you may use this code as per gpl version 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 5 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528171439.762454146@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add POWER_SUPPLY_HEALTH_OVERCURRENT constant in order to allow
singalling overcurrent condition via power supply health information.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: Enric Balletbo Serra <enric.balletbo@collabora.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-kernel@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Add POWER_SUPPLY_PROP_CHARGE_CONTROL_START_THRESHOLD
and POWER_SUPPLY_PROP_CHARGE_CONTROL_END_THRESHOLD properties, to expand
the existing CHARGE_CONTROL_* properties. I am adding them in order
to support a new Chrome OS device, but these properties should be
general enough that they can be used on other devices.
When the charge_type is "Custom", the charge controller uses the
POWER_SUPPLY_PROP_CHARGE_CONTROL_* properties as configuration for some
other algorithm. For example, in the use case that I am supporting,
this means the battery begins charging when the percentage
level drops below POWER_SUPPLY_PROP_CHARGE_CONTROL_START_THRESHOLD and
charging ceases when the percentage level goes above
POWER_SUPPLY_PROP_CHARGE_CONTROL_END_THRESHOLD.
v5 changes:
- Add the other missing CHARGE_CONTROL_* properties documentation in
a separate commit
- Split up adding the charge types and adding the
POWER_SUPPLY_PROP_CHARGE_CONTROL_START_THRESHOLD and
POWER_SUPPLY_PROP_CHARGE_CONTROL_END_THRESHOLD properties into
two different commits.
v4 changes:
- Add documentation for the new properties, and add documentation for
the the previously missing charge_control_limit and
charge_control_limit_max properties.
Signed-off-by: Nick Crews <ncrews@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Add "Standard", "Adaptive", and "Custom" modes to the charge_type
property, to expand the existing "Trickle" and "Fast" modes.
I am adding them in order to support a new Chrome OS device,
but these properties should be general enough that they can be
used on other devices.
The meaning of "Standard" is obvious, but "Adaptive" and "Custom" are
more tricky: "Adaptive" means that the charge controller uses some
custom algorithm to change the charge type automatically, with no
configuration needed. "Custom" means that the charge controller uses the
POWER_SUPPLY_PROP_CHARGE_CONTROL_* properties as configuration for some
other algorithm.
v5 changes:
- Split up adding the charge types and adding the
POWER_SUPPLY_PROP_CHARGE_CONTROL_START_THRESHOLD and
POWER_SUPPLY_PROP_CHARGE_CONTROL_END_THRESHOLD properties into
two different commits.
v4 changes:
- Add documentation for the new properties, and add documentation for
the the previously missing charge_control_limit and
charge_control_limit_max properties.
Signed-off-by: Nick Crews <ncrews@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Add a field for "voltage_max_design_uv" to present fully charged
battery voltage.
Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Add functionality to setup device specific sysfs attributes
in a race condition free manner
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
We have introduced some battery properties to present the OCV table
temperatures and OCV capacity table values. Thus this patch add OCV
temperature and OCV table for battery information, as well as providing
some helper functions to use the OCV capacity table for users.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Add one field for 'struct power_supply_battery_info' to present the battery
factory internal resistance.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
If a device gets removed right after having registered a power_supply node,
we might enter in a deadlock between the remove call (that has a lock on
the parent device) and the deferred register work.
Allow the deferred register work to exit without taking the lock when
we are in the remove state.
Stack trace on a Ubuntu 16.04:
[16072.109121] INFO: task kworker/u16:2:1180 blocked for more than 120 seconds.
[16072.109127] Not tainted 4.13.0-41-generic #46~16.04.1-Ubuntu
[16072.109129] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[16072.109132] kworker/u16:2 D 0 1180 2 0x80000000
[16072.109142] Workqueue: events_power_efficient power_supply_deferred_register_work
[16072.109144] Call Trace:
[16072.109152] __schedule+0x3d6/0x8b0
[16072.109155] schedule+0x36/0x80
[16072.109158] schedule_preempt_disabled+0xe/0x10
[16072.109161] __mutex_lock.isra.2+0x2ab/0x4e0
[16072.109166] __mutex_lock_slowpath+0x13/0x20
[16072.109168] ? __mutex_lock_slowpath+0x13/0x20
[16072.109171] mutex_lock+0x2f/0x40
[16072.109174] power_supply_deferred_register_work+0x2b/0x50
[16072.109179] process_one_work+0x15b/0x410
[16072.109182] worker_thread+0x4b/0x460
[16072.109186] kthread+0x10c/0x140
[16072.109189] ? process_one_work+0x410/0x410
[16072.109191] ? kthread_create_on_node+0x70/0x70
[16072.109194] ret_from_fork+0x35/0x40
[16072.109199] INFO: task test:2257 blocked for more than 120 seconds.
[16072.109202] Not tainted 4.13.0-41-generic #46~16.04.1-Ubuntu
[16072.109204] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[16072.109206] test D 0 2257 2256 0x00000004
[16072.109208] Call Trace:
[16072.109211] __schedule+0x3d6/0x8b0
[16072.109215] schedule+0x36/0x80
[16072.109218] schedule_timeout+0x1f3/0x360
[16072.109221] ? check_preempt_curr+0x5a/0xa0
[16072.109224] ? ttwu_do_wakeup+0x1e/0x150
[16072.109227] wait_for_completion+0xb4/0x140
[16072.109230] ? wait_for_completion+0xb4/0x140
[16072.109233] ? wake_up_q+0x70/0x70
[16072.109236] flush_work+0x129/0x1e0
[16072.109240] ? worker_detach_from_pool+0xb0/0xb0
[16072.109243] __cancel_work_timer+0x10f/0x190
[16072.109247] ? device_del+0x264/0x310
[16072.109250] ? __wake_up+0x44/0x50
[16072.109253] cancel_delayed_work_sync+0x13/0x20
[16072.109257] power_supply_unregister+0x37/0xb0
[16072.109260] devm_power_supply_release+0x11/0x20
[16072.109263] release_nodes+0x110/0x200
[16072.109266] devres_release_group+0x7c/0xb0
[16072.109274] wacom_remove+0xc2/0x110 [wacom]
[16072.109279] hid_device_remove+0x6e/0xd0 [hid]
[16072.109284] device_release_driver_internal+0x158/0x210
[16072.109288] device_release_driver+0x12/0x20
[16072.109291] bus_remove_device+0xec/0x160
[16072.109293] device_del+0x1de/0x310
[16072.109298] hid_destroy_device+0x27/0x60 [hid]
[16072.109303] usbhid_disconnect+0x51/0x70 [usbhid]
[16072.109308] usb_unbind_interface+0x77/0x270
[16072.109311] device_release_driver_internal+0x158/0x210
[16072.109315] device_release_driver+0x12/0x20
[16072.109318] usb_driver_release_interface+0x77/0x80
[16072.109321] proc_ioctl+0x20f/0x250
[16072.109325] usbdev_do_ioctl+0x57f/0x1140
[16072.109327] ? __wake_up+0x44/0x50
[16072.109331] usbdev_ioctl+0xe/0x20
[16072.109336] do_vfs_ioctl+0xa4/0x600
[16072.109339] ? vfs_write+0x15a/0x1b0
[16072.109343] SyS_ioctl+0x79/0x90
[16072.109347] entry_SYSCALL_64_fastpath+0x24/0xab
[16072.109349] RIP: 0033:0x7f20da807f47
[16072.109351] RSP: 002b:00007ffc422ae398 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
[16072.109353] RAX: ffffffffffffffda RBX: 00000000010b8560 RCX: 00007f20da807f47
[16072.109355] RDX: 00007ffc422ae3a0 RSI: 00000000c0105512 RDI: 0000000000000009
[16072.109356] RBP: 0000000000000000 R08: 00007ffc422ae3e0 R09: 0000000000000010
[16072.109357] R10: 00000000000000a6 R11: 0000000000000246 R12: 0000000000000000
[16072.109359] R13: 00000000010b8560 R14: 00007ffc422ae2e0 R15: 0000000000000000
Reported-and-tested-by: Richard Hughes <rhughes@redhat.com>
Tested-by: Aaron Skomra <Aaron.Skomra@wacom.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Fixes: 7f1a57fdd6cb ("power_supply: Fix possible NULL pointer dereference on early uevent")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
|
|
To allow users of the power supply framework to be hw description
agnostic, this commit adds the ability to pass a fwnode pointer,
via the power_supply_config structure, to the initialisation code
of the core, instead of explicitly specifying of_ndoe. If that
fwnode pointer is provided then it will automatically resolve down
to of_node on platforms which support it, otherwise it will be NULL.
In the future, when ACPI support is added, this can be modified to
accommodate ACPI without the need to change calling code which
already provides the fwnode handle in this manner.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This commit adds the 'usb_type' property to represent USB supplies
which can report a number of different types based on a connection
event.
Examples of this already exist in drivers whereby the existing 'type'
property is updated, based on an event, to represent what was
connected (e.g. USB, USB_DCP, USB_ACA, ...). Current implementations
however don't show all supported connectable types, so this knowledge
has to be exlicitly known for each driver that supports this.
The 'usb_type' property is intended to fill this void and show users
all possible USB types supported by a driver. The property, when read,
shows all available types for the driver, and the one currently chosen
is highlighted/bracketed. It is expected that the 'type' property
would then just show the top-level type 'USB', and this would be
static.
Currently the 'usb_type' enum contains all of the USB variant types
that exist for the 'type' enum at this time, and in addition has
SDP and PPS types. The mirroring is intentional so as to not impact
existing usage of the 'type' property.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch adds the to_power_supply macro to upcast
a device to a power_supply struct.
This is needed because the same piece of code using
container_of is used in various other places, so we
abstract away such low-level operations via a macro.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ognjen Galic <smclt30p@gmail.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
On some devices the USB Type-C port power (USB PD 2.0) negotiation is
done by a separate port-controller IC, while the current limit is
controlled through another (charger) IC.
It has been decided to model this by modelling the external Type-C
power brick (adapter/charger) as a power-supply class device which
supplies the charger-IC, with its voltage-now and current-max representing
the negotiated voltage and max current draw.
This commit adds a power_supply_set_input_current_limit_from_supplier
helper function which charger power-supply drivers can call to get
the max-current from their supplier and have this applied
through their set_property call-back to their input-current-limit.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
|
|
Battery chargers use POWER_SUPPLY_PROP_PRECHARGE_CURRENT
Clarify related item POWER_SUPPLY_PROP_CHARGE_TERM_CURRENT
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
|
|
power_supply_get_battery_info() reads battery data from devicetree.
struct power_supply_battery_info provides battery data to drivers.
Its fields correspond to elements in enum power_supply_property.
Drivers may surface battery data in sysfs via corresponding
POWER_SUPPLY_PROP_* fields.
Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
|
|
Apple currently supports three very common USB chargers:
https://www.apple.com/power-adapters/
These chargers implement a proprietary Apple method for advertising
1A, 2.1A, and 2.4A at 5V called "Brick ID".
In addition, 3rd parties implement the same charging method in many
charging accessories that work with iOS devices.
Devices that have charger detection chips such as the Pericom PI3USB9281,
eg. Google Chromebook Pixel 2015, are capable of detecting
these chargers, so let's add a type to facilicate passing that info
up to userspace.
This adds a separate power supply type for Apple's proprietary
"Brick ID" charging method.
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
|
|
power_supply_get_property() should ideally return -EAGAIN if it is
called while the power_supply is being registered. There was no way
previously to determine if use_cnt == 0 meant that the power_supply
wasn't fully registered yet, or if it had already been unregistered.
Add a new boolean to the power_supply struct to simply show if
registration is completed. Lastly, modify the check in
power_supply_show_property() to also ignore -EAGAIN when so it
doesn't complain about not returning the property.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
This adds power supply types for USB chargers defined in
the USB Type-C Specification 1.1 and in the
USB Power Delivery Specification Revision 2.0 V1.1.
The following are added :
POWER_SUPPLY_TYPE_USB_TYPE_C, /* Type C Port */
POWER_SUPPLY_TYPE_USB_PD, /* Power Delivery Port */
POWER_SUPPLY_TYPE_USB_PD_DRP, /* PD Dual Role Port */
Signed-off-by: Benson Leung <bleung@chromium.org>
[tomeu: remove the mention to Type C from the comments]
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Todd Broch <tbroch@chromium.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
This commit adds a resource-managed version of the
power_supply_get_by_phandle() function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
Linus Walleij
Ricardo Rivera-Matos
Hans de Goede
Linus Torvalds
Thomas Weißschuh
Luca Ceresoli
Jiapeng Chong
Ray Chi
Subbaraman Narayanamurthy
Dmitry Osipenko
Crag Wang
Dan Murphy
Sebastian Reichel
Matti Vaittinen
Michał Mirosław
Baolin Wang
Enric Balletbo i Serra
Andrey Smirnov
Thomas Gleixner
Nick Crews
Artur Rojek
Benjamin Tissoires
Adam Thomson
Ognjen Galic
Liam Breck
Benson Leung
Rhyland Klein