| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
It has been observed with certain PCIe USB cards (like Inateck connected
to AM64 EVM or J7200 EVM) that as soon as the primary roothub is
registered, port status change is handled even before xHC is running
leading to cold plug USB devices not detected. For such cases, registering
both the root hubs along with the second HCD is required. Add support for
deferring roothub registration in usb_add_hcd(), so that both primary and
secondary roothubs are registered along with the second HCD.
CC: stable@vger.kernel.org # 5.4+
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Chris Chiu <chris.chiu@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20210909064200.16216-2-kishon@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Refactor struct ehci_regs to avoid accessing beyond the end of
port_status. This change results in no difference in the final
object code.
Avoids several warnings when building with -Warray-bounds:
drivers/usb/host/ehci-brcm.c: In function 'ehci_brcm_reset':
drivers/usb/host/ehci-brcm.c:113:32: warning: array subscript 16 is above array bounds of 'u32[15]' {aka 'unsigned int[15]'} [-Warray-bounds]
113 | ehci_writel(ehci, 0x00800040, &ehci->regs->port_status[0x10]);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/usb/host/ehci.h:274,
from drivers/usb/host/ehci-brcm.c:15:
./include/linux/usb/ehci_def.h:132:7: note: while referencing 'port_status'
132 | u32 port_status[HCS_N_PORTS_MAX];
| ^~~~~~~~~~~
Note that the documentation around this proprietary register was
confusing. If "USB_EHCI_INSNREG00" is at port_status[0x0f], its offset
would be 0x80 (not 0x90). The comments have been adjusted to fix this
apparent typo.
Fixes: 9df231511bd6 ("usb: ehci: Add new EHCI driver for Broadcom STB SoC's")
Cc: Al Cooper <alcooperx@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Cc: bcm-kernel-feedback-list@broadcom.com
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20210818173018.2259231-3-keescook@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The original EHCI register struct used a trailing 0-element array for
addressing the N_PORTS-many available registers. However, after commit
a46af4ebf9ff ("USB: EHCI: define extension registers like normal ones")
the 0-element array started to overlap the USBMODE extension register.
To avoid future compile-time warnings about accessing indexes within a
0-element array, rearrange the struct to actually describe the expected
layout (max 15 registers) with a union. All offsets remain the same, and
bounds checking becomes possible on accesses to port_status and hostpc.
There are no binary differences, and struct offsets continue to match.
"pahole --hex -C ehci_regs" before:
struct ehci_regs {
u32 command; /* 0 0x4 */
u32 status; /* 0x4 0x4 */
u32 intr_enable; /* 0x8 0x4 */
u32 frame_index; /* 0xc 0x4 */
u32 segment; /* 0x10 0x4 */
u32 frame_list; /* 0x14 0x4 */
u32 async_next; /* 0x18 0x4 */
u32 reserved1[2]; /* 0x1c 0x8 */
u32 txfill_tuning; /* 0x24 0x4 */
u32 reserved2[6]; /* 0x28 0x18 */
/* --- cacheline 1 boundary (64 bytes) --- */
u32 configured_flag; /* 0x40 0x4 */
u32 port_status[0]; /* 0x44 0 */
u32 reserved3[9]; /* 0x44 0x24 */
u32 usbmode; /* 0x68 0x4 */
u32 reserved4[6]; /* 0x6c 0x18 */
/* --- cacheline 2 boundary (128 bytes) was 4 bytes ago --- */
u32 hostpc[0]; /* 0x84 0 */
u32 reserved5[17]; /* 0x84 0x44 */
/* --- cacheline 3 boundary (192 bytes) was 8 bytes ago --- */
u32 usbmode_ex; /* 0xc8 0x4 */
/* size: 204, cachelines: 4, members: 18 */
/* last cacheline: 12 bytes */
};
after:
struct ehci_regs {
u32 command; /* 0 0x4 */
u32 status; /* 0x4 0x4 */
u32 intr_enable; /* 0x8 0x4 */
u32 frame_index; /* 0xc 0x4 */
u32 segment; /* 0x10 0x4 */
u32 frame_list; /* 0x14 0x4 */
u32 async_next; /* 0x18 0x4 */
u32 reserved1[2]; /* 0x1c 0x8 */
u32 txfill_tuning; /* 0x24 0x4 */
u32 reserved2[6]; /* 0x28 0x18 */
/* --- cacheline 1 boundary (64 bytes) --- */
u32 configured_flag; /* 0x40 0x4 */
union {
u32 port_status[15]; /* 0x44 0x3c */
struct {
u32 reserved3[9]; /* 0x44 0x24 */
u32 usbmode; /* 0x68 0x4 */
}; /* 0x44 0x28 */
}; /* 0x44 0x3c */
/* --- cacheline 2 boundary (128 bytes) --- */
u32 reserved4; /* 0x80 0x4 */
u32 hostpc[15]; /* 0x84 0x3c */
/* --- cacheline 3 boundary (192 bytes) --- */
u32 reserved5[2]; /* 0xc0 0x8 */
u32 usbmode_ex; /* 0xc8 0x4 */
/* size: 204, cachelines: 4, members: 16 */
/* last cacheline: 12 bytes */
};
With this fixed, adding -Wzero-length-bounds to the build no longer
produces several warnings like this:
In file included from drivers/usb/host/ehci-hcd.c:306:
drivers/usb/host/ehci-hub.c: In function 'ehci_port_handed_over':
drivers/usb/host/ehci-hub.c:1194:8: warning: array subscript '<unknown>' is outside the bounds of an interior zero-length array 'u32[0]' {aka 'unsigned int[]'} [-Wzero-length-bounds]
1194 | reg = &ehci->regs->port_status[portnum - 1];
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/usb/host/ehci.h:274,
from drivers/usb/host/ehci-hcd.c:97:
./include/linux/usb/ehci_def.h:130:7: note: while referencing 'port_status'
130 | u32 port_status[0]; /* up to N_PORTS */
| ^~~~~~~~~~~
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Al Cooper <alcooperx@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: linux-usb@vger.kernel.org
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20210818173018.2259231-2-keescook@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
usb_endpoint_maxp() already returns actual max packet size, no need
to AND 0x7ff.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1628836253-7432-7-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the usb fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The HNP work can be re-scheduled while it's still in-fly. This results in
re-initialization of the busy work, resetting the hrtimer's list node of
the work and crashing kernel with null dereference within kernel/timer
once work's timer is expired. It's very easy to trigger this problem by
re-plugging USB cable quickly. Initialize HNP work only once to fix this
trouble.
Unable to handle kernel NULL pointer dereference at virtual address 00000126)
...
PC is at __run_timers.part.0+0x150/0x228
LR is at __next_timer_interrupt+0x51/0x9c
...
(__run_timers.part.0) from [<c0187a2b>] (run_timer_softirq+0x2f/0x50)
(run_timer_softirq) from [<c01013ad>] (__do_softirq+0xd5/0x2f0)
(__do_softirq) from [<c012589b>] (irq_exit+0xab/0xb8)
(irq_exit) from [<c0170341>] (handle_domain_irq+0x45/0x60)
(handle_domain_irq) from [<c04c4a43>] (gic_handle_irq+0x6b/0x7c)
(gic_handle_irq) from [<c0100b65>] (__irq_svc+0x65/0xac)
Cc: stable@vger.kernel.org
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210717182134.30262-6-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add helper to get "role-switch-default-mode", and convert it
to the corresponding enum usb_dr_mode
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1626340078-29111-6-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Similar to UAC1 spec, UAC2 feature unit descriptor
has variable size.
Current audio-v2 feature unit descriptor structure
is used for parsing descriptors, but can't be used
to define your own descriptor.
Add a new macro similar to what audio v1 already has.
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Signed-off-by: Pavel Hofman <pavel.hofman@ivitera.com>
Link: https://lore.kernel.org/r/20210712125529.76070-2-pavel.hofman@ivitera.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some UDCs may have constraints on how many high bandwidth endpoints it can
support in a certain configuration. This API allows for the composite
driver to pass down the total number of endpoints to the UDC so it can verify
it has the required resources to support the configuration.
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1625908395-5498-2-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt patches for 5.14-rc1.
Nothing major here just lots of little changes for new hardware and
features. Highlights are:
- more USB 4 support added to the thunderbolt core
- build warning fixes all over the place
- usb-serial driver updates and new device support
- mtu3 driver updates
- gadget driver updates
- dwc3 driver updates
- dwc2 driver updates
- isp1760 host driver updates
- musb driver updates
- lots of other tiny things.
Full details are in the shortlog.
All of these have been in linux-next for a while now with no reported
issues"
* tag 'usb-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (223 commits)
phy: qcom-qusb2: Add configuration for SM4250 and SM6115
dt-bindings: phy: qcom,qusb2: document sm4250/6115 compatible
dt-bindings: usb: qcom,dwc3: Add bindings for sm6115/4250
USB: cdc-acm: blacklist Heimann USB Appset device
usb: xhci-mtk: allow multiple Start-Split in a microframe
usb: ftdi-elan: remove redundant continue statement in a while-loop
usb: class: cdc-wdm: return the correct errno code
xhci: remove redundant continue statement
usb: dwc3: Fix debugfs creation flow
usb: gadget: hid: fix error return code in hid_bind()
usb: gadget: eem: fix echo command packet response issue
usb: gadget: f_hid: fix endianness issue with descriptors
Revert "USB: misc: Add onboard_usb_hub driver"
Revert "of/platform: Add stubs for of_platform_device_create/destroy()"
Revert "usb: host: xhci-plat: Create platform device for onboard hubs in probe()"
Revert "arm64: dts: qcom: sc7180-trogdor: Add nodes for onboard USB hub"
xhci: solve a double free problem while doing s4
xhci: handle failed buffer copy to URB sg list and fix a W=1 copiler warning
xhci: Add adaptive interrupt rate for isoch TRBs with XHCI_AVOID_BEI quirk
xhci: Remove unused defines for ERST_SIZE and ERST_ENTRIES
...
|
|
Johan writes:
USB-serial updates for 5.14-rc1
Here are the USB-serial updates for 5.14-rc1, including:
- gpio support for CP2108
- chars_in_buffer and write_room return-value updates
- chars_in_buffer and write_room clean ups
Included are also various clean ups.
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.14-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: cp210x: add support for GPIOs on CP2108
USB: serial: drop irq-flags initialisations
USB: serial: mos7840: drop buffer-callback return-value comments
USB: serial: mos7720: drop buffer-callback sanity checks
USB: serial: io_edgeport: drop buffer-callback sanity checks
USB: serial: digi_acceleport: add chars_in_buffer locking
USB: serial: digi_acceleport: reduce chars_in_buffer over-reporting
USB: serial: make usb_serial_driver::chars_in_buffer return uint
USB: serial: make usb_serial_driver::write_room return uint
|
|
Trivial conflicts in net/can/isotp.c and
tools/testing/selftests/net/mptcp/mptcp_connect.sh
scaled_ppm_to_ppb() was moved from drivers/ptp/ptp_clock.c
to include/linux/ptp_clock_kernel.h in -next so re-apply
the fix there.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This reverts commit b4e326165e21d6a11483f6a4de2174b933413554 as the
patch series is causing build issues in linux-next at the moment.
Cc: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/YMuRcrE8xlWnFSWW@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The main issue this driver addresses is that a USB hub needs to be
powered before it can be discovered. For discrete onboard hubs (an
example for such a hub is the Realtek RTS5411) this is often solved
by supplying the hub with an 'always-on' regulator, which is kind
of a hack. Some onboard hubs may require further initialization
steps, like changing the state of a GPIO or enabling a clock, which
requires even more hacks. This driver creates a platform device
representing the hub which performs the necessary initialization.
Currently it only supports switching on a single regulator, support
for multiple regulators or other actions can be added as needed.
Different initialization sequences can be supported based on the
compatible string.
Besides performing the initialization the driver can be configured
to power the hub off during system suspend. This can help to extend
battery life on battery powered devices which have no requirements
to keep the hub powered during suspend. The driver can also be
configured to leave the hub powered when a wakeup capable USB device
is connected when suspending, and power it off otherwise.
Technically the driver consists of two drivers, the platform driver
described above and a very thin USB driver that subclasses the
generic driver. The purpose of this driver is to provide the platform
driver with the USB devices corresponding to the hub(s) (a hub
controller may provide multiple 'logical' hubs, e.g. one to support
USB 2.0 and another for USB 3.x).
Note: the current series only supports hubs connected directly to
a root hub (through xhci-plat), support for other configurations
could be added if needed.
Co-developed-by: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20210609150159.v12.2.I7c9a1f1d6ced41dd8310e8a03da666a32364e790@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We want the usb fixes in here as well, and this resolves some merge
issues with:
drivers/usb/dwc3/debugfs.c
drivers/usb/dwc3/gadget.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Gadget API has a theoretical race when a gadget driver is unbound.
Although the pull-up is turned off before the driver's ->unbind
callback runs, if the USB cable were to be unplugged at just the wrong
moment there would be nothing to prevent the UDC driver from invoking
the ->disconnect callback after the unbind has finished. In theory,
other asynchronous callbacks could also happen during the time before
the UDC driver's udc_stop routine is called, and the gadget driver
would not be prepared to handle any of them.
We need a way to tell UDC drivers to stop issuing asynchronous (that is,
->suspend, ->resume, ->disconnect, ->reset, or ->setup) callbacks at
some point after the pull-up has been turned off and before the
->unbind callback runs. This patch adds a new ->udc_async_callbacks
callback to the usb_gadget_ops structure for precisely this purpose,
and it adds the corresponding support to the UDC core.
Later patches in this series add support for udc_async_callbacks to
several UDC drivers.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20210520202144.GC1216852@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When receiving Alert Message, if it is not unexpected but is
unsupported for some reason, the port should return Not_Supported
Message response.
Also, according to PD3.0 Spec 6.5.2.1.4 Event Flags Field, the
OTP/OVP/OCP flags in the Event Flags field in Status Message no longer
require Get_PPS_Status Message to clear them. Thus remove it when
receiving Status Message with those flags being set.
In addition, add the missing AMS operations for Status Message.
Fixes: 64f7c494a3c0 ("typec: tcpm: Add support for sink PPS related messages")
Fixes: 0908c5aca31e ("usb: typec: tcpm: AMS and Collision Avoidance")
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210531164928.2368606-1-kyletso@google.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Current timer PD_T_SINK_WAIT_CAP is set to 240ms which will violate the
SinkWaitCapTimer (tTypeCSinkWaitCap 310 - 620 ms) defined in the PD
Spec if the port is faster enough when running the state machine. Set it
to the lower bound 310ms to ensure the timeout is in Spec.
Fixes: f0690a25a140 ("staging: typec: USB Type-C Port Manager (tcpm)")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210528081613.730661-1-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Introduces usb_role_string() function, which returns a
human-readable name of provided usb role, it's useful to
make the log readable.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1621932786-9335-1-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When vbus auto discharge is enabled, TCPCI based TCPC transitions
into Attached.SNK/Attached.SRC state. During PR_SWAP, TCPCI based
TCPC would disconnect when partner changes power roles. TCPC has
to be moved APPLY RC state during PR_SWAP. This is done by
ROLE_CONTROL.CC1 != ROLE_CONTROL.CC2 and
POWER_CONTROL.AutodischargeDisconnect is 0. Once the swap sequence
is done, AutoDischargeDisconnect is re-enabled.
Fixes: f321a02caebd ("usb: typec: tcpm: Implement enabling Auto Discharge disconnect support")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210517192112.40934-3-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since the removal of the Blackfin port with:
commit 4ba66a976072 ("arch: remove blackfin port")
No one is using or referencing this header and platform data struct.
Remove them.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Link: https://lore.kernel.org/r/20210513084717.2487366-5-rui.silva@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix some spelling mistakes in comments:
trasfer ==> transfer
consumtion ==> consumption
endoint ==> endpoint
sharable ==> shareable
contraints ==> constraints
Auxilary ==> Auxiliary
correspondig ==> corresponding
interupt ==> interrupt
inifinite ==> infinite
assignement ==> assignment
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20210517094020.7310-1-thunder.leizhen@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
tty_operations::chars_in_buffer is being switched to return uint. Do the
same for usb_serial_driver's chars_in_buffer.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
[ johan: amend commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Line disciplines expect a positive value or zero returned from
tty->ops->write_room (invoked by tty_write_room). Both of them are being
updated to return an unsigned int. Switch also
usb_serial_driver::write_room and all its users.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
[ johan: amend commit message, drop unrelated comment change ]
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
It is needed at USB Certification test for Embedded Host 2.0, and
the detail is at CH6.4.1.1 of On-The-Go and Embedded Host Supplement
to the USB Revision 2.0 Specification. Since other USB 2.0 capable
host like XHCI also need it, so move it to HCD core.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Link: https://lore.kernel.org/r/1620452039-11694-1-git-send-email-jun.li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The WWAN framework provides a unified way to handle WWAN/modems and its
control port(s). It has initially been introduced to support MHI/PCI
modems, offering the same control protocols as the USB variants such as
MBIM, QMI, AT... The WWAN framework exposes these control protocols as
character devices, similarly to cdc-wdm, but in a bus agnostic fashion.
This change adds registration of the USB modem cdc-wdm control endpoints
to the WWAN framework as standard control ports (wwanXpY...).
Exposing cdc-wdm through WWAN framework normally maintains backward
compatibility, e.g:
$ qmicli --device-open-qmi -d /dev/wwan0p1QMI --dms-get-ids
instead of
$ qmicli --device-open-qmi -d /dev/cdc-wdm0 --dms-get-ids
However, some tools may rely on cdc-wdm driver/device name for device
detection. It is then safer to keep the 'legacy' cdc-wdm character
device to prevent any breakage. This is handled in this change by
API mutual exclusion, only one access method can be used at a time,
either cdc-wdm chardev or WWAN API.
Note that unknown channel types (other than MBIM, AT or MBIM) are not
registered to the WWAN framework.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking updates from Jakub Kicinski:
"Core:
- bpf:
- allow bpf programs calling kernel functions (initially to
reuse TCP congestion control implementations)
- enable task local storage for tracing programs - remove the
need to store per-task state in hash maps, and allow tracing
programs access to task local storage previously added for
BPF_LSM
- add bpf_for_each_map_elem() helper, allowing programs to walk
all map elements in a more robust and easier to verify fashion
- sockmap: support UDP and cross-protocol BPF_SK_SKB_VERDICT
redirection
- lpm: add support for batched ops in LPM trie
- add BTF_KIND_FLOAT support - mostly to allow use of BTF on
s390 which has floats in its headers files
- improve BPF syscall documentation and extend the use of kdoc
parsing scripts we already employ for bpf-helpers
- libbpf, bpftool: support static linking of BPF ELF files
- improve support for encapsulation of L2 packets
- xdp: restructure redirect actions to avoid a runtime lookup,
improving performance by 4-8% in microbenchmarks
- xsk: build skb by page (aka generic zerocopy xmit) - improve
performance of software AF_XDP path by 33% for devices which don't
need headers in the linear skb part (e.g. virtio)
- nexthop: resilient next-hop groups - improve path stability on
next-hops group changes (incl. offload for mlxsw)
- ipv6: segment routing: add support for IPv4 decapsulation
- icmp: add support for RFC 8335 extended PROBE messages
- inet: use bigger hash table for IP ID generation
- tcp: deal better with delayed TX completions - make sure we don't
give up on fast TCP retransmissions only because driver is slow in
reporting that it completed transmitting the original
- tcp: reorder tcp_congestion_ops for better cache locality
- mptcp:
- add sockopt support for common TCP options
- add support for common TCP msg flags
- include multiple address ids in RM_ADDR
- add reset option support for resetting one subflow
- udp: GRO L4 improvements - improve 'forward' / 'frag_list'
co-existence with UDP tunnel GRO, allowing the first to take place
correctly even for encapsulated UDP traffic
- micro-optimize dev_gro_receive() and flow dissection, avoid
retpoline overhead on VLAN and TEB GRO
- use less memory for sysctls, add a new sysctl type, to allow using
u8 instead of "int" and "long" and shrink networking sysctls
- veth: allow GRO without XDP - this allows aggregating UDP packets
before handing them off to routing, bridge, OvS, etc.
- allow specifing ifindex when device is moved to another namespace
- netfilter:
- nft_socket: add support for cgroupsv2
- nftables: add catch-all set element - special element used to
define a default action in case normal lookup missed
- use net_generic infra in many modules to avoid allocating
per-ns memory unnecessarily
- xps: improve the xps handling to avoid potential out-of-bound
accesses and use-after-free when XPS change race with other
re-configuration under traffic
- add a config knob to turn off per-cpu netdev refcnt to catch
underflows in testing
Device APIs:
- add WWAN subsystem to organize the WWAN interfaces better and
hopefully start driving towards more unified and vendor-
independent APIs
- ethtool:
- add interface for reading IEEE MIB stats (incl. mlx5 and bnxt
support)
- allow network drivers to dump arbitrary SFP EEPROM data,
current offset+length API was a poor fit for modern SFP which
define EEPROM in terms of pages (incl. mlx5 support)
- act_police, flow_offload: add support for packet-per-second
policing (incl. offload for nfp)
- psample: add additional metadata attributes like transit delay for
packets sampled from switch HW (and corresponding egress and
policy-based sampling in the mlxsw driver)
- dsa: improve support for sandwiched LAGs with bridge and DSA
- netfilter:
- flowtable: use direct xmit in topologies with IP forwarding,
bridging, vlans etc.
- nftables: counter hardware offload support
- Bluetooth:
- improvements for firmware download w/ Intel devices
- add support for reading AOSP vendor capabilities
- add support for virtio transport driver
- mac80211:
- allow concurrent monitor iface and ethernet rx decap
- set priority and queue mapping for injected frames
- phy: add support for Clause-45 PHY Loopback
- pci/iov: add sysfs MSI-X vector assignment interface to distribute
MSI-X resources to VFs (incl. mlx5 support)
New hardware/drivers:
- dsa: mv88e6xxx: add support for Marvell mv88e6393x - 11-port
Ethernet switch with 8x 1-Gigabit Ethernet and 3x 10-Gigabit
interfaces.
- dsa: support for legacy Broadcom tags used on BCM5325, BCM5365 and
BCM63xx switches
- Microchip KSZ8863 and KSZ8873; 3x 10/100Mbps Ethernet switches
- ath11k: support for QCN9074 a 802.11ax device
- Bluetooth: Broadcom BCM4330 and BMC4334
- phy: Marvell 88X2222 transceiver support
- mdio: add BCM6368 MDIO mux bus controller
- r8152: support RTL8153 and RTL8156 (USB Ethernet) chips
- mana: driver for Microsoft Azure Network Adapter (MANA)
- Actions Semi Owl Ethernet MAC
- can: driver for ETAS ES58X CAN/USB interfaces
Pure driver changes:
- add XDP support to: enetc, igc, stmmac
- add AF_XDP support to: stmmac
- virtio:
- page_to_skb() use build_skb when there's sufficient tailroom
(21% improvement for 1000B UDP frames)
- support XDP even without dedicated Tx queues - share the Tx
queues with the stack when necessary
- mlx5:
- flow rules: add support for mirroring with conntrack, matching
on ICMP, GTP, flex filters and more
- support packet sampling with flow offloads
- persist uplink representor netdev across eswitch mode changes
- allow coexistence of CQE compression and HW time-stamping
- add ethtool extended link error state reporting
- ice, iavf: support flow filters, UDP Segmentation Offload
- dpaa2-switch:
- move the driver out of staging
- add spanning tree (STP) support
- add rx copybreak support
- add tc flower hardware offload on ingress traffic
- ionic:
- implement Rx page reuse
- support HW PTP time-stamping
- octeon: support TC hardware offloads - flower matching on ingress
and egress ratelimitting.
- stmmac:
- add RX frame steering based on VLAN priority in tc flower
- support frame preemption (FPE)
- intel: add cross time-stamping freq difference adjustment
- ocelot:
- support forwarding of MRP frames in HW
- support multiple bridges
- support PTP Sync one-step timestamping
- dsa: mv88e6xxx, dpaa2-switch: offload bridge port flags like
learning, flooding etc.
- ipa: add IPA v4.5, v4.9 and v4.11 support (Qualcomm SDX55, SM8350,
SC7280 SoCs)
- mt7601u: enable TDLS support
- mt76:
- add support for 802.3 rx frames (mt7915/mt7615)
- mt7915 flash pre-calibration support
- mt7921/mt7663 runtime power management fixes"
* tag 'net-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2451 commits)
net: selftest: fix build issue if INET is disabled
net: netrom: nr_in: Remove redundant assignment to ns
net: tun: Remove redundant assignment to ret
net: phy: marvell: add downshift support for M88E1240
net: dsa: ksz: Make reg_mib_cnt a u8 as it never exceeds 255
net/sched: act_ct: Remove redundant ct get and check
icmp: standardize naming of RFC 8335 PROBE constants
bpf, selftests: Update array map tests for per-cpu batched ops
bpf: Add batched ops support for percpu array
bpf: Implement formatted output helpers with bstr_printf
seq_file: Add a seq_bprintf function
sfc: adjust efx->xdp_tx_queue_count with the real number of initialized queues
net:nfc:digital: Fix a double free in digital_tg_recv_dep_req
net: fix a concurrency bug in l2tp_tunnel_register()
net/smc: Remove redundant assignment to rc
mpls: Remove redundant assignment to err
llc2: Remove redundant assignment to rc
net/tls: Remove redundant initialization of record
rds: Remove redundant assignment to nr_sig
dt-bindings: net: mdio-gpio: add compatible for microchip,mdio-smi0
...
|
|
Johan writes:
USB-serial updates for 5.13-rc1
Here are the USB-serial updates for 5.13-rc1, including:
- better type detection for pl2303
- support for more line speeds for pl2303 (TA/TB)
- fixed CSIZE handling for the new xr driver
- core support for multi-interface functions
- TIOCGSERIAL and TIOCSSERIAL fixes
- generic TIOCSSERIAL support (e.g. for closing_wait)
- fixed return value for unsupported ioctls
- support for gpio valid masks in cp210x
- drain-delay fixes and improvements
- support for multi-port devices for xr
- generalisation of the xr driver to support three new device classes
(XR21B142X, XR21B1411 and XR2280X)
Included are also various clean ups.
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.13-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial: (72 commits)
USB: cdc-acm: add more Maxlinear/Exar models to ignore list
USB: serial: xr: add copyright notice
USB: serial: xr: reset FIFOs on open
USB: serial: xr: add support for XR22801, XR22802, XR22804
USB: serial: xr: add support for XR21B1411
USB: serial: xr: add support for XR21B1421, XR21B1422 and XR21B1424
USB: serial: xr: add type abstraction
USB: serial: xr: drop type prefix from shared defines
USB: serial: xr: move pin configuration to probe
USB: serial: xr: rename GPIO-pin defines
USB: serial: xr: rename GPIO-mode defines
USB: serial: xr: add support for XR21V1412 and XR21V1414
USB: serial: ti_usb_3410_5052: clean up termios CSIZE handling
USB: serial: ti_usb_3410_5052: use kernel types consistently
USB: serial: ti_usb_3410_5052: add port-command helpers
USB: serial: ti_usb_3410_5052: clean up vendor-request helpers
USB: serial: ti_usb_3410_5052: drop unnecessary packed attributes
USB: serial: io_ti: drop unnecessary packed attributes
USB: serial: io_ti: use kernel types consistently
USB: serial: io_ti: add read-port-command helper
...
|
|
>From PD Spec:
The Sink Shall transition to Sink Standby before a positive or
negative voltage transition of VBUS. During Sink Standby
the Sink Shall reduce its power draw to pSnkStdby. This allows
the Source to manage the voltage transition as well as
supply sufficient operating current to the Sink to maintain PD
operation during the transition. The Sink Shall
complete this transition to Sink Standby within tSnkStdby
after evaluating the Accept Message from the Source. The
transition when returning to Sink operation from Sink Standby
Shall be completed within tSnkNewPower. The
pSnkStdby requirement Shall only apply if the Sink power draw
is higher than this level.
The above requirement needs to be met to prevent hard resets
from port partner.
Without the patch: (5V/3A during SNK_DISCOVERY all the way through
explicit contract)
[ 95.711984] CC1: 0 -> 0, CC2: 0 -> 5 [state TOGGLING, polarity 0, connected]
[ 95.712007] state change TOGGLING -> SNK_ATTACH_WAIT [rev3 NONE_AMS]
[ 95.712017] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev3 NONE_AMS]
[ 95.837190] VBUS on
[ 95.882075] state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED [delayed 170 ms]
[ 95.882082] state change SNK_DEBOUNCED -> SNK_ATTACHED [rev3 NONE_AMS]
[ 95.882086] polarity 1
[ 95.883151] set_auto_vbus_discharge_threshold mode:0 pps_active:n vbus:5000 ret:0
[ 95.883441] enable vbus discharge ret:0
[ 95.883445] Requesting mux state 1, usb-role 2, orientation 2
[ 95.883776] state change SNK_ATTACHED -> SNK_STARTUP [rev3 NONE_AMS]
[ 95.883879] pending state change SNK_STARTUP -> SNK_DISCOVERY @ 500 ms [rev3 NONE_AMS]
[ 96.038960] VBUS on
[ 96.383939] state change SNK_STARTUP -> SNK_DISCOVERY [delayed 500 ms]
[ 96.383946] Setting voltage/current limit 5000 mV 3000 mA
[ 96.383961] vbus=0 charge:=1
[ 96.386044] state change SNK_DISCOVERY -> SNK_WAIT_CAPABILITIES [rev3 NONE_AMS]
[ 96.386309] pending state change SNK_WAIT_CAPABILITIES -> HARD_RESET_SEND @ 450 ms [rev3 NONE_AMS]
[ 96.394404] PD RX, header: 0x2161 [1]
[ 96.394408] PDO 0: type 0, 5000 mV, 3000 mA [E]
[ 96.394410] PDO 1: type 0, 9000 mV, 2000 mA []
[ 96.394412] state change SNK_WAIT_CAPABILITIES -> SNK_NEGOTIATE_CAPABILITIES [rev2 POWER_NEGOTIATION]
[ 96.394416] Setting usb_comm capable false
[ 96.395083] cc=0 cc1=0 cc2=5 vbus=0 vconn=sink polarity=1
[ 96.395089] Requesting PDO 1: 9000 mV, 2000 mA
[ 96.395093] PD TX, header: 0x1042
[ 96.397404] PD TX complete, status: 0
[ 96.397424] pending state change SNK_NEGOTIATE_CAPABILITIES -> HARD_RESET_SEND @ 60 ms [rev2 POWER_NEGOTIATION]
[ 96.400826] PD RX, header: 0x363 [1]
[ 96.400829] state change SNK_NEGOTIATE_CAPABILITIES -> SNK_TRANSITION_SINK [rev2 POWER_NEGOTIATION]
[ 96.400832] pending state change SNK_TRANSITION_SINK -> HARD_RESET_SEND @ 500 ms [rev2 POWER_NEGOTIATION]
[ 96.577315] PD RX, header: 0x566 [1]
[ 96.577321] Setting voltage/current limit 9000 mV 2000 mA
[ 96.578363] set_auto_vbus_discharge_threshold mode:3 pps_active:n vbus:9000 ret:0
[ 96.578370] state change SNK_TRANSITION_SINK -> SNK_READY [rev2 POWER_NEGOTIATION]
With the patch:
[ 168.398573] CC1: 0 -> 0, CC2: 0 -> 5 [state TOGGLING, polarity 0, connected]
[ 168.398605] state change TOGGLING -> SNK_ATTACH_WAIT [rev3 NONE_AMS]
[ 168.398619] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev3 NONE_AMS]
[ 168.522348] VBUS on
[ 168.568676] state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED [delayed 170 ms]
[ 168.568684] state change SNK_DEBOUNCED -> SNK_ATTACHED [rev3 NONE_AMS]
[ 168.568688] polarity 1
[ 168.569867] set_auto_vbus_discharge_threshold mode:0 pps_active:n vbus:5000 ret:0
[ 168.570158] enable vbus discharge ret:0
[ 168.570161] Requesting mux state 1, usb-role 2, orientation 2
[ 168.570504] state change SNK_ATTACHED -> SNK_STARTUP [rev3 NONE_AMS]
[ 168.570634] pending state change SNK_STARTUP -> SNK_DISCOVERY @ 500 ms [rev3 NONE_AMS]
[ 169.070689] state change SNK_STARTUP -> SNK_DISCOVERY [delayed 500 ms]
[ 169.070695] Setting voltage/current limit 5000 mV 3000 mA
[ 169.070702] vbus=0 charge:=1
[ 169.072719] state change SNK_DISCOVERY -> SNK_WAIT_CAPABILITIES [rev3 NONE_AMS]
[ 169.073145] pending state change SNK_WAIT_CAPABILITIES -> HARD_RESET_SEND @ 450 ms [rev3 NONE_AMS]
[ 169.077162] PD RX, header: 0x2161 [1]
[ 169.077172] PDO 0: type 0, 5000 mV, 3000 mA [E]
[ 169.077178] PDO 1: type 0, 9000 mV, 2000 mA []
[ 169.077183] state change SNK_WAIT_CAPABILITIES -> SNK_NEGOTIATE_CAPABILITIES [rev2 POWER_NEGOTIATION]
[ 169.077191] Setting usb_comm capable false
[ 169.077753] cc=0 cc1=0 cc2=5 vbus=0 vconn=sink polarity=1
[ 169.077759] Requesting PDO 1: 9000 mV, 2000 mA
[ 169.077762] PD TX, header: 0x1042
[ 169.079990] PD TX complete, status: 0
[ 169.080013] pending state change SNK_NEGOTIATE_CAPABILITIES -> HARD_RESET_SEND @ 60 ms [rev2 POWER_NEGOTIATION]
[ 169.083183] VBUS on
[ 169.084195] PD RX, header: 0x363 [1]
[ 169.084200] state change SNK_NEGOTIATE_CAPABILITIES -> SNK_TRANSITION_SINK [rev2 POWER_NEGOTIATION]
[ 169.084206] Setting standby current 5000 mV @ 500 mA
[ 169.084209] Setting voltage/current limit 5000 mV 500 mA
[ 169.084220] pending state change SNK_TRANSITION_SINK -> HARD_RESET_SEND @ 500 ms [rev2 POWER_NEGOTIATION]
[ 169.260222] PD RX, header: 0x566 [1]
[ 169.260227] Setting voltage/current limit 9000 mV 2000 mA
[ 169.261315] set_auto_vbus_discharge_threshold mode:3 pps_active:n vbus:9000 ret:0
[ 169.261321] state change SNK_TRANSITION_SINK -> SNK_READY [rev2 POWER_NEGOTIATION]
[ 169.261570] AMS POWER_NEGOTIATION finished
Fixes: f0690a25a140b ("staging: typec: USB Type-C Port Manager (tcpm)")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210414024000.4175263-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This can be used by Type-C controller drivers which use a standard
usb-connector fwnode, with altmodes sub-node, to describe the available
altmodes.
Note there are is no devicetree bindings documentation for the altmodes
node, this is deliberate. ATM the fwnodes used to register the altmodes
are only used internally to pass platform info from a drivers/platform/x86
driver to the type-c subsystem.
When a devicetree user of this functionally comes up and the dt-bindings
have been hashed out the internal use can be adjusted to match the
dt-bindings.
Currently the typec_port_register_altmodes() function expects
an "altmodes" child fwnode on port->dev with this "altmodes" fwnode having
child fwnodes itself with each child containing 2 integer properties:
1. A "svid" property, which sets the id of the altmode, e.g. displayport
altmode has a svid of 0xff01.
2. A "vdo" property, typically used as a bitmask describing the
capabilities of the altmode, the bits in the vdo are specified in the
specification of the altmode.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210409134033.105834-2-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Adding functions that can be used to link/unlink ports -
USB ports, TBT3/USB4 ports, DisplayPorts and so on - to
the USB Type-C connectors they are attached to inside a
system. The symlink that is created for the port device is
named "connector".
Initially only ACPI is supported. ACPI port object shares
the _PLD (Physical Location of Device) with the USB Type-C
connector that it's attached to.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20210407065555.88110-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
The closing_wait parameter determines how long to wait for the transfer
buffers to drain during close and the default timeout of 30 seconds may
not be sufficient at low line speeds. In other cases, when for example
flow is stopped, the default timeout may instead be too long.
Add generic support for TIOCSSERIAL and TIOCGSERIAL with handling of the
three common parameters close_delay, closing_wait and line for the
benefit of all USB serial drivers while still allowing drivers to
implement further functionality through the existing callbacks.
This currently includes a few drivers that report their base baud clock
rate even if that is really only of interest when setting custom
divisors through the deprecated ASYNC_SPD_CUST interface; an interface
which only the FTDI driver actually implements.
Some drivers have also been reporting back a fake UART type, something
which should no longer be needed and will be dropped by a follow-on
patch.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
The old method for reporting link speed assumed a driver uses the
generic phy (mii) MDIO read/write functions. CDC devices don't
expose the phy.
Add a primitive internal version reporting back directly what
the CDC notification/status operations recorded.
v2: rebased on upstream
v3: changed names and made clear which units are used
v4: moved hunks to correct patch; rewrote commmit messages
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Tested-by: Roland Dreier <roland@kernel.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Tested-by: Grant Grundler <grundler@chromium.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The generic functions assumed devices provided an MDIO interface (accessed
via older mii code, not phylib). This is true only for genuine ethernet.
Devices with a higher level of abstraction or based on different
technologies do not have MDIO. To support this case, first rename
the existing functions with _mii suffix.
v2: rebased on changed upstream
v3: changed names to clearly say that this does NOT use phylib
v4: moved hunks to correct patch; reworded commmit messages
Signed-off-by : Oliver Neukum <oneukum@suse.com>
Tested-by: Roland Dreier <roland@kernel.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Tested-by: Grant Grundler <grundler@chromium.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A single USB function can be implemented using a group of interfaces and
this is for example commonly used for Communication Class devices.
Add support for multi-interface functions to USB serial core and export
an interface that allows drivers to claim a second sibling interface.
The interface could easily be extended to allow claiming further
interfaces if ever needed.
When a driver claims a sibling interface in probe(), core allocates
resources for any bulk in, bulk out, interrupt in and interrupt out
endpoints found also on the sibling interface.
Disconnect is implemented so that unbinding either interface will
release the other interface while disconnect() is called precisely once.
Similarly, suspend() is called when the first sibling interface is
suspended and resume() is called when the last sibling interface is
resumed by USB core.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
The suspending flag was added back in 2009 but no users ever followed.
Remove it.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
This patch adds an ignore_oc flag which can be set by EHCI controller
not supporting or wanting to disable overcurrent checking. The EHCI
platform data in include/linux/usb/ehci_pdriver.h is also augmented to
take advantage of this new flag.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Link: https://lore.kernel.org/r/20210223174455.1378-2-noltari@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Following a general rule, add the kerneldoc for a function next
to it's definition, but not next to its declaration in a header
file.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/c4d2e010ae2bf67cdfa0b55e6d1deb9339d9d3dc.1615170625.git.chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add a new function to convert bInterval into the time expressed
in 1us unit.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/25c8a09b055f716c1e5bf11fea72c3418f844482.1615170625.git.chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pull Kbuild updates from Masahiro Yamada:
- Fix false-positive build warnings for ARCH=ia64 builds
- Optimize dictionary size for module compression with xz
- Check the compiler and linker versions in Kconfig
- Fix misuse of extra-y
- Support DWARF v5 debug info
- Clamp SUBLEVEL to 255 because stable releases 4.4.x and 4.9.x
exceeded the limit
- Add generic syscall{tbl,hdr}.sh for cleanups across arches
- Minor cleanups of genksyms
- Minor cleanups of Kconfig
* tag 'kbuild-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (38 commits)
initramfs: Remove redundant dependency of RD_ZSTD on BLK_DEV_INITRD
kbuild: remove deprecated 'always' and 'hostprogs-y/m'
kbuild: parse C= and M= before changing the working directory
kbuild: reuse this-makefile to define abs_srctree
kconfig: unify rule of config, menuconfig, nconfig, gconfig, xconfig
kconfig: omit --oldaskconfig option for 'make config'
kconfig: fix 'invalid option' for help option
kconfig: remove dead code in conf_askvalue()
kconfig: clean up nested if-conditionals in check_conf()
kconfig: Remove duplicate call to sym_get_string_value()
Makefile: Remove # characters from compiler string
Makefile: reuse CC_VERSION_TEXT
kbuild: check the minimum linker version in Kconfig
kbuild: remove ld-version macro
scripts: add generic syscallhdr.sh
scripts: add generic syscalltbl.sh
arch: syscalls: remove $(srctree)/ prefix from syscall tables
arch: syscalls: add missing FORCE and fix 'targets' to make if_changed work
gen_compile_commands: prune some directories
kbuild: simplify access to the kernel's version
...
|
|
Pull USB and Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt driver changes for
5.12-rc1.
It's been an active set of development in these subsystems for the
past few months:
- loads of typec features added for new hardware
- xhci features and bugfixes
- dwc3 features added for more hardware support
- dwc2 fixes and new hardware support
- cdns3 driver updates for more hardware support
- gadget driver cleanups and minor fixes
- usb-serial fixes, new driver, and more devices supported
- thunderbolt feature additions for new hardware
- lots of other tiny fixups and additions
The chrome driver changes are in here as well, as they depended on
some of the typec changes, and the maintainer acked them.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (300 commits)
dt-bindings: usb: mediatek: musb: add mt8516 compatbile
dt-bindings: usb: mtk-xhci: add compatible for mt2701 and mt7623
dt-bindings: usb: mtk-xhci: add optional assigned clock properties
Documentation: connector: Update the description of sink-vdos
usb: misc: usb3503: Fix logic in usb3503_init()
dt-bindings: usb: usb-device: fix typo in required properties
usb: Replace lkml.org links with lore
dt-bindings: usb: dwc3: add description for rk3328
dt-bindings: usb: convert rockchip,dwc3.txt to yaml
usb: quirks: add quirk to start video capture on ELMO L-12F document camera reliable
USB: quirks: sort quirk entries
USB: serial: drop bogus to_usb_serial_port() checks
USB: serial: make remove callback return void
USB: serial: drop if with an always false condition
usb: gadget: Assign boolean values to a bool variable
usb: typec: tcpm: Get Sink VDO from fwnode
dt-bindings: connector: Add SVDM VDO properties
usb: typec: displayport: Fill the negotiated SVDM Version in the header
usb: typec: ucsi: Determine common SVDM Version
usb: typec: tcpm: Determine common SVDM Version
...
|
|
Instead of storing the version in a single integer and having various
kernel (and userspace) code how it's constructed, export individual
(major, patchlevel, sublevel) components and simplify kernel code that
uses it.
This should also make it easier on userspace.
Signed-off-by: Sasha Levin <sashal@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
Johan writes:
USB-serial updates for 5.12-rc1
Here are the USB-serial updates for 5.12-rc1, including:
- a line-speed fix for newer pl2303 devices
- a line-speed fix for FTDI FT-X devices
- a new xr_serial driver for MaxLinear/Exar devices (non-ACM mode)
- a cdc-acm blacklist entry for when the xr_serial driver is enabled
- cp210x support for software flow control
- various cp210x modem-control fixes
- an updated ZTE P685M modem entry to stop claiming the QMI interface
- an update to drop the port_remove() driver-callback return value
Included are also various clean ups.
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.12-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial: (41 commits)
USB: serial: drop bogus to_usb_serial_port() checks
USB: serial: make remove callback return void
USB: serial: drop if with an always false condition
USB: serial: option: update interface mapping for ZTE P685M
USB: serial: ftdi_sio: restore divisor-encoding comments
USB: serial: ftdi_sio: fix FTX sub-integer prescaler
USB: serial: cp210x: clean up auto-RTS handling
USB: serial: cp210x: fix RTS handling
USB: serial: cp210x: clean up printk zero padding
USB: serial: cp210x: clean up flow-control debug message
USB: serial: cp210x: drop shift macros
USB: serial: cp210x: fix modem-control handling
USB: serial: cp210x: suppress modem-control errors
USB: serial: mos7720: fix error code in mos7720_write()
USB: serial: xr: fix B0 handling
USB: serial: xr: fix pin configuration
USB: serial: xr: fix gpio-mode handling
USB: serial: xr: simplify line-speed logic
USB: serial: xr: clean up line-settings handling
USB: serial: xr: document vendor-request recipient
...
|
|
All usb_serial drivers return 0 in their remove callbacks and driver
core ignores the value returned by usb_serial_device_remove(). So change
the remove callback to return void and return 0 unconditionally in
usb_serial_device_remove().
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Link: https://lore.kernel.org/r/20210208143149.963644-2-uwe@kleine-koenig.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
PD Rev 3.0 introduces SVDM Version 2.0. This patch makes the field
configuable in the header in order to be able to be compatible with
older SVDM version.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210205033415.3320439-3-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
PD Spec Revision 3.0 Version 2.0 + ECNs 2020-12-10
6.4.4.2.3 Structured VDM Version
"The Structured VDM Version field of the Discover Identity Command
sent and received during VDM discovery Shall be used to determine the
lowest common Structured VDM Version supported by the Port Partners or
Cable Plug and Shall continue to operate using this Specification
Revision until they are Detached."
Add a variable in typec_capability to specify the highest SVDM version
supported by the port and another variable in typec_partner to cache the
negotiated SVDM version between the port and the partner.
Also add setter/getter functions for the negotiated SVDM version.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210205033415.3320439-2-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The USB "maximum-speed" property can now take the SSP signaling rate
generation and lane count with these new strings:
"super-speed-plus-gen2x2"
"super-speed-plus-gen2x1"
"super-speed-plus-gen1x2"
Introduce usb_get_maximum_ssp_rate() to parse for the corresponding
usb_ssp_rate enum. The original usb_get_maximum_speed() will return
USB_SPEED_SUPER_PLUS if it matches one of these new strings.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/f8ed896313d8cd8e2d2b540fc82db92b3ddf8a47.1611106162.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Reland VDO definitions of PD Revision 2.0 as they are still used in
PD2.0 products.
Fixes: 0e1d6f55a12e ("usb: pd: Update VDO definitions")
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210204005036.1555294-1-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This converts the driver to use the new tasklet API introduced in
commit 12cc923f1ccc ("tasklet: Introduce new initialization API")
It is unfortunate that we need to add a pointer to the driver context to
get back to the usbnet device, but the space will be reclaimed once
there are no more users of the old API left and we can remove the data
value and flag from the tasklet struct.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20210130234637.26505-1-kernel@esmil.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
"PD Spec Revision 3.0 Version 2.0 + ECNs 2020-12-10" introduces several
changes regarding the ID Header VDO and the Product Type VDOs.
Signed-off-by: Kyle Tso <kyletso@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20210202161733.932215-3-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
Kishon Vijay Abraham I
Kees Cook
Chunfeng Yun
Greg Kroah-Hartman
Dmitry Osipenko
Ruslan Bilovol
Wesley Cheng
Linus Torvalds
Jakub Kicinski
Matthias Kaehlcke
Alan Stern
Kyle Tso
Badhri Jagan Sridharan
Rui Miguel Silva
Zhen Lei
Jiri Slaby
Peter Chen
Loic Poulain
Hans de Goede
Heikki Krogerus
Johan Hovold
Oliver Neukum
Florian Fainelli
Sasha Levin
Uwe Kleine-König
Thinh Nguyen
Emil Renner Berthing