| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This patch centralizes computing of max rx/tx qlen, because:
- RX_QLEN()/TX_QLEN() is called in hot path
- computing depends on device's usb speed, now we have ls/fs, hs, ss,
so more checks need to be involved
- in fact, max rx/tx qlen should not only depend on device USB
speed, but also depend on ethernet link speed, so we need to
consider that in future.
- if SG support is done, max tx qlen may need change too
Generally, hard_mtu and rx_urb_size are changed in bind(), reset()
and link_reset() callback, and change mtu network operation, this
patches introduces the API of usbnet_update_max_qlen(), and calls
it in above path.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull ARM SoC specific changes from Arnd Bergmann:
"These changes are all to SoC-specific code, a total of 33 branches on
17 platforms were pulled into this. Like last time, Renesas sh-mobile
is now the platform with the most changes, followed by OMAP and
EXYNOS.
Two new platforms, TI Keystone and Rockchips RK3xxx are added in this
branch, both containing almost no platform specific code at all, since
they are using generic subsystem interfaces for clocks, pinctrl,
interrupts etc. The device drivers are getting merged through the
respective subsystem maintainer trees.
One more SoC (u300) is now multiplatform capable and several others
(shmobile, exynos, msm, integrator, kirkwood, clps711x) are moving
towards that goal with this series but need more work.
Also noteworthy is the work on PCI here, which is traditionally part
of the SoC specific code. With the changes done by Thomas Petazzoni,
we can now more easily have PCI host controller drivers as loadable
modules and keep them separate from the platform code in
drivers/pci/host. This has already led to the discovery that three
platforms (exynos, spear and imx) are actually using an identical PCIe
host controller and will be able to share a driver once support for
spear and imx is added."
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (480 commits)
ARM: integrator: let pciv3 use mem/premem from device tree
ARM: integrator: set local side PCI addresses right
ARM: dts: Add pcie controller node for exynos5440-ssdk5440
ARM: dts: Add pcie controller node for Samsung EXYNOS5440 SoC
ARM: EXYNOS: Enable PCIe support for Exynos5440
pci: Add PCIe driver for Samsung Exynos
ARM: OMAP5: voltagedomain data: remove temporary OMAP4 voltage data
ARM: keystone: Move CPU bringup code to dedicated asm file
ARM: multiplatform: always pick one CPU type
ARM: imx: select syscon for IMX6SL
ARM: keystone: select ARM_ERRATA_798181 only for SMP
ARM: imx: Synertronixx scb9328 needs to select SOC_IMX1
ARM: OMAP2+: AM43x: resolve SMP related build error
dmaengine: edma: enable build for AM33XX
ARM: edma: Add EDMA crossbar event mux support
ARM: edma: Add DT and runtime PM support to the private EDMA API
dmaengine: edma: Add TI EDMA device tree binding
arm: add basic support for Rockchip RK3066a boards
arm: add debug uarts for rockchip rk29xx and rk3xxx series
arm: Add basic clocks for Rockchip rk3066a SoCs
...
|
|
"ci13xxx" is bad for at least the following reasons:
* people often mistype it
* it doesn't add any informational value to the names it's used in
* it needlessly attracts mail filters
This patch replaces it with "ci_hdrc", "ci_udc" or "ci_hw", depending
on the situation. Modules with ci13xxx prefix are also renamed accordingly
and aliases are added for compatibility. Otherwise, no functional changes.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
on i386:
drivers/built-in.o: In function `ci_hdrc_probe':
core.c:(.text+0x20446b): undefined reference to `of_usb_get_phy_mode'
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Tegra EHCI driver directly calls various functions in the Tegra USB
PHY driver. The reverse is also true; the PHY driver calls into the EHCI
driver. This is problematic when the two are built as modules.
The calls from the PHY to EHCI driver were originally added in commit
bbdabdb "usb: add APIs to access host registers from Tegra PHY", for the
following reasons:
1) The register being touched is an EHCI register, so logically only the
EHCI driver should touch it.
2) (1) implies that some locking may be needed to correctly implement the
r/m/w access to this shared register.
3) We were expecting to pass only the PHY register space to the Tegra PHY
driver, and hence it would not have access to touch the shared
registers.
To solve this, that commit added functions in the EHCI driver to touch the
shared register on behalf of the PHY driver.
In practice, we ended up not having any locking in the implementaiton of
those functions, and I've been led to believe this is safe. Equally, (3)
did not happen either. Hence, it is possible for the PHY driver to touch
the shared register directly.
Given that, this patch moves the code to touch the shared register back
into the PHY driver, to eliminate the module problems. If we actually
need locking or co-ordination in the future, I propose we put the lock
support into some pre-existing core module, or into a third separate
module, in order to avoid the circular dependencies.
I apologize for my contribution to code churn here.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Even if a chipidea core is otg capable the board may not be. This allows
to explicitly set the core to host/peripheral mode. Without these flags
the driver falls back to the old behaviour.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch makes it possible to configure the PTW, PTS and STS bits
inside the portsc register for host and device mode before the driver
starts and the phy can be addressed as hardware implementation is
designed.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This adds two little devicetree helper functions for determining the
dr_mode (host, peripheral, otg) and phy_type (utmi, ulpi,...) from
the devicetree.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We had the limit of 255 USB to serial devices on one system for almost
15 years, with no complaints. But now it's time to move on from these
tiny "baby" systems, and bump the number up to 512, which should last
us a few more years:
"512 is a nice number" -- Tobias Winter
Note, this is still a static value, and uses up tty core memory with
this many tty devices allocated. Converting the driver to use
TTY_DRIVER_DYNAMIC_DEV is the next thing to do in order to remove this
limitation.
Reported-by: Tobias Winter <tobias@linuxdingsda.de>
Tested-by: Tobias Winter <tobias@linuxdingsda.de>
Reviewed-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This moves the allocation of minor device numbers from a static array to
be dynamic, using the idr interface. This means that you could
potentially get "gaps" in a minor number range for a single USB serial
device with multiple ports, but all should still work properly.
We remove the 'minor' field from the usb_serial structure, as it no
longer makes any sense for it (use the field in the usb_serial_port
structure if you really want to know this number), and take the fact
that we were overloading a number in this field to determine if we had
initialized the minor numbers or not, and just use a flag variable
instead.
Note, we still have the limitation of 255 USB to serial devices in the
system, as that is all we are registering with the TTY layer at this
point in time.
Tested-by: Tobias Winter <tobias@linuxdingsda.de>
Reviewed-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
From Simon Horman:
Renesas USB updates for v3.11
These updates are by Sergei Shtylyov to clean-up USB support
present for R8A7779/Marzen and then extend USB support coverage to
R8A7778/BOCK-W.
* tag 'renesas-phy-rcar-usb-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: BOCK-W: add USB support
ARM: shmobile: r8a7778: add USB support
phy-rcar-usb: add R8A7778 support
phy-rcar-usb: handle platform data
ARM: shmobile: Marzen: pass platform data to USB PHY device
phy-rcar-usb: add platform data
phy-rcar-usb: correct base address
ARM: shmobile: r8a7779: remove USB PHY 2nd memory resource
phy-rcar-usb: remove EHCI internal buffer setup
ARM: shmobile: r8a7779: setup EHCI internal buffer
ehci-platform: add pre_setup() method to platform data
ARM: shmobile: Marzen: move USB EHCI, OHCI, and PHY devices to R8A7779 code
Conflicts:
arch/arm/mach-shmobile/board-marzen.c
arch/arm/mach-shmobile/setup-r8a7778.c
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Felipe writes:
usb: patches for v3.11 merge window
All function drivers are now converted to our new configfs-based
binding. Eventually this will help us getting rid of in-kernel
gadget drivers and only keep function drivers in the kernel.
MUSB was taught that it needs to be built for host-only and
device-only modes too. We had this support long ago but it
involved a ridiculous amount of ifdefs. Now we have a much
cleaner approach.
Samsung Exynos4 platform now implements HSIC support.
We're introducing support for AB8540 and AB9540 PHYs.
MUSB module reinsertion now works as expected, before we were
getting -EBUSY being returned by the resource checks done on
driver core.
DWC3 now has minimum support for TI's AM437x series of SoCs.
OMAP5 USB3 PHY learned one extra DPLL configuration values because
that PHY is reused in TI's DRA7xx devices.
We're introducing support for Faraday fotg210 UDCs.
Last, but not least, the usual set of non-critical fixes and cleanups
ranging from usage of platform_{get,set}_drvdata to lock improvements.
Signed-of-by: Felipe Balbi <balbi@ti.com>
|
|
Sometimes there is a need to initialize some non-standard registers mapped to
the EHCI region before accessing the standard EHCI registers. Add pre_setup()
method with 'struct usb_hcd *' parameter to be called just before ehci_setup()
to the 'ehci-platform' driver's platform data for this purpose...
While at it, add the missing incomplete declaration of 'struct platform_device'
to <linux/usb/ehci_pdriver.h>...
The patch has been tested on the Marzen and BOCK-W boards.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The usb_serial_port structure had the number field, which was the minor
number for the port, which almost no one really cared about. They
really wanted the number of the port within the device, which you had to
subtract from the minor of the parent usb_serial_device structure. To
clean this up, provide the real minor number of the port, and the number
of the port within the serial device separately, as these numbers might
not be related in the future.
Bonus is that this cleans up a lot of logic in the drivers, and saves
lines overall.
Tested-by: Tobias Winter <tobias@linuxdingsda.de>
Reviewed-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
--
drivers/staging/serqt_usb2/serqt_usb2.c | 21 +++--------
drivers/usb/serial/ark3116.c | 2 -
drivers/usb/serial/bus.c | 6 +--
drivers/usb/serial/console.c | 2 -
drivers/usb/serial/cp210x.c | 2 -
drivers/usb/serial/cypress_m8.c | 4 +-
drivers/usb/serial/digi_acceleport.c | 6 ---
drivers/usb/serial/f81232.c | 5 +-
drivers/usb/serial/garmin_gps.c | 6 +--
drivers/usb/serial/io_edgeport.c | 58 ++++++++++++--------------------
drivers/usb/serial/io_ti.c | 21 ++++-------
drivers/usb/serial/keyspan.c | 29 +++++++---------
drivers/usb/serial/metro-usb.c | 4 +-
drivers/usb/serial/mos7720.c | 37 +++++++++-----------
drivers/usb/serial/mos7840.c | 52 +++++++++-------------------
drivers/usb/serial/opticon.c | 2 -
drivers/usb/serial/pl2303.c | 2 -
drivers/usb/serial/quatech2.c | 7 +--
drivers/usb/serial/sierra.c | 2 -
drivers/usb/serial/ti_usb_3410_5052.c | 10 ++---
drivers/usb/serial/usb-serial.c | 7 ++-
drivers/usb/serial/usb_wwan.c | 2 -
drivers/usb/serial/whiteheat.c | 20 +++++------
include/linux/usb/serial.h | 6 ++-
24 files changed, 133 insertions(+), 180 deletions(-)
|
|
This patch adds the HWA specific members to struct usb_rpipe_descriptor
and sets them correctly based on the wireless endpoint compananion
descriptor.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch adds Wireless USB root hub support to the USB HCD. It allows
the HWA to create its root hub which previously failed because the HCD
treated wireless root hubs the same as USB2 high speed hubs. The creation
of the root hub would fail in that case due to lack of TTs which wireless
root hubs do not support.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Registered Tegra USB PHY as a separate platform driver.
To synchronize host controller and PHY initialization, used deferred
probe mechanism. As PHY should be initialized before EHCI starts running,
deferred probe of Tegra EHCI driver till PHY probe gets completed.
Got rid of instance number based handling in host driver.
Made use of DT params to get the PHY Pad registers.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
As GPIO information is avail through DT, used it to get Tegra ULPI
reset GPIO number. Added a new member to tegra_usb_phy structure to
store this number.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Added a new PHY mode to support OTG.
Obtained Tegra USB PHY mode using DT property.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Add generic wait_until_sent implementation which polls for empty
hardware buffers using the new port-operation tx_empty.
The generic implementation will be used for all sub-drivers that
implement tx_empty but does not define wait_until_sent.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add wait_until_sent operation which can be used to wait for hardware
buffers to drain.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Tidy up kernel-doc content for USB GADGET. No functional change.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Some drivers (sierra_net) need the status interrupt URB
active even when the device is closed, because they receive
custom indications from firmware. Add functions to refcount
the status interrupt URB submit/kill operation so that
sub-drivers and the generic driver don't fight over whether
the status interrupt URB is active or not.
A sub-driver can call usbnet_status_start() at any time, but
the URB is only submitted the first time the function is
called. Likewise, when the sub-driver is done with the URB,
it calls usbnet_status_stop() but the URB is only killed when
all users have stopped it. The URB is still killed and
re-submitted for suspend/resume, as before, with the same
refcount it had at suspend.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull sound updates from Takashi Iwai:
"Mostly many small changes spread as seen in diffstat in sound/*
directory by this update. A significant change in the subsystem level
is the introduction of snd_soc_component, which will help more generic
handling of SoC and off-SoC components.
Also, snd_BUG_ON() macro is enabled unconditionally now due to its
misuses, so people might hit kernel warnings (it's a good thing for
us).
- compress-offload: support for capture by Charles Keepax
- HD-audio: codec delay support by Dylan Reid
- HD-audio: improvements/fixes in generic parser: better headphone
mic and headset mic support, jack_modes hint consolidation, proper
beep attach/detachment, generalized power filter controls by David
Henningsson, et al
- HD-audio: Improved management of HDMI codec pins/converters
- HD-audio: Better pin/DAC assignment for VIA codecs
- HD-audio: Haswell HDMI workarounds
- HD-audio: ALC268 codec support, a few new quirks for Chromebooks
- USB: regression fixes: USB-MIDI autopm fix, the recent ISO latency
fix by Clemens Ladisch
- USB: support for DSD formats by Daniel Mack
- USB: A few UAC2 device endian/cock fixes by Eldad Zack
- USB: quirks for Emu 192kHz support, Novation Twitch DJ controller,
Yamaha THRxx devices
- HDSPM: updates for TCO controls by Adrian Knoth
- ASoC: Add a snd_soc_component object type for generic handling of
SoC and off-SoC components by Kuninori Morimoto,
- dmaengine: a large set of cleanups and conversions by Lars-Peter
Clausen
- ASoC DAPM: performance optimizations from Ryo Tsutsui
- ASoC DAPM: support for mixer control sharing by Stephen Warren
- ASoC: multiplatform ARM cleanups from Arnd Bergmann
- ASoC: new codec drivers for AK5385 and TAS5086 from Daniel Mack"
* tag 'sound-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (315 commits)
ALSA: usb-audio: caiaq: fix endianness bug in snd_usb_caiaq_maschine_dispatch
ALSA: asihpi: add format support check in snd_card_asihpi_capture_formats
ALSA: pcm_format_to_bits strong-typed conversion
ALSA: compress: fix the states to check for allowing read
ALSA: hda - Move Thinkpad X220 to use auto parser
ALSA: USB: adjust for changed 3.8 USB API
ALSA: usb - Avoid unnecessary sample rate changes on USB 2.0 clock sources
sound: oss/dmabuf: use dma_map_single
ALSA: ali5451: use mdelay instead of large udelay constants
ALSA: hda - Add the support for ALC286 codec
ALSA: usb-audio: USB quirk for Yamaha THR10C
ALSA: usb-audio: USB quirk for Yamaha THR5A
ALSA: usb-audio: USB quirk for Yamaha THR10
ALSA: usb-audio: Fix autopm error during probing
ALSA: snd-usb: try harder to find USB_DT_CS_ENDPOINT
ALSA: sound kconfig typo
ALSA: emu10k1: Fix dock firmware loading
ASoC: ux500: forward declare msp_i2s_platform_data
ASoC: davinci-mcasp: Add Support BCLK-to-LRCLK ratio for TDM modes
ASoC: davinci-pcm, davinci-mcasp: Clean up active_serializers
...
|
|
Pull networking updates from David Miller:
"Highlights (1721 non-merge commits, this has to be a record of some
sort):
1) Add 'random' mode to team driver, from Jiri Pirko and Eric
Dumazet.
2) Make it so that any driver that supports configuration of multiple
MAC addresses can provide the forwarding database add and del
calls by providing a default implementation and hooking that up if
the driver doesn't have an explicit set of handlers. From Vlad
Yasevich.
3) Support GSO segmentation over tunnels and other encapsulating
devices such as VXLAN, from Pravin B Shelar.
4) Support L2 GRE tunnels in the flow dissector, from Michael Dalton.
5) Implement Tail Loss Probe (TLP) detection in TCP, from Nandita
Dukkipati.
6) In the PHY layer, allow supporting wake-on-lan in situations where
the PHY registers have to be written for it to be configured.
Use it to support wake-on-lan in mv643xx_eth.
From Michael Stapelberg.
7) Significantly improve firewire IPV6 support, from YOSHIFUJI
Hideaki.
8) Allow multiple packets to be sent in a single transmission using
network coding in batman-adv, from Martin Hundebøll.
9) Add support for T5 cxgb4 chips, from Santosh Rastapur.
10) Generalize the VXLAN forwarding tables so that there is more
flexibility in configurating various aspects of the endpoints.
From David Stevens.
11) Support RSS and TSO in hardware over GRE tunnels in bxn2x driver,
from Dmitry Kravkov.
12) Zero copy support in nfnelink_queue, from Eric Dumazet and Pablo
Neira Ayuso.
13) Start adding networking selftests.
14) In situations of overload on the same AF_PACKET fanout socket, or
per-cpu packet receive queue, minimize drop by distributing the
load to other cpus/fanouts. From Willem de Bruijn and Eric
Dumazet.
15) Add support for new payload offset BPF instruction, from Daniel
Borkmann.
16) Convert several drivers over to mdoule_platform_driver(), from
Sachin Kamat.
17) Provide a minimal BPF JIT image disassembler userspace tool, from
Daniel Borkmann.
18) Rewrite F-RTO implementation in TCP to match the final
specification of it in RFC4138 and RFC5682. From Yuchung Cheng.
19) Provide netlink socket diag of netlink sockets ("Yo dawg, I hear
you like netlink, so I implemented netlink dumping of netlink
sockets.") From Andrey Vagin.
20) Remove ugly passing of rtnetlink attributes into rtnl_doit
functions, from Thomas Graf.
21) Allow userspace to be able to see if a configuration change occurs
in the middle of an address or device list dump, from Nicolas
Dichtel.
22) Support RFC3168 ECN protection for ipv6 fragments, from Hannes
Frederic Sowa.
23) Increase accuracy of packet length used by packet scheduler, from
Jason Wang.
24) Beginning set of changes to make ipv4/ipv6 fragment handling more
scalable and less susceptible to overload and locking contention,
from Jesper Dangaard Brouer.
25) Get rid of using non-type-safe NLMSG_* macros and use nlmsg_*()
instead. From Hong Zhiguo.
26) Optimize route usage in IPVS by avoiding reference counting where
possible, from Julian Anastasov.
27) Convert IPVS schedulers to RCU, also from Julian Anastasov.
28) Support cpu fanouts in xt_NFQUEUE netfilter target, from Holger
Eitzenberger.
29) Network namespace support for nf_log, ebt_log, xt_LOG, ipt_ULOG,
nfnetlink_log, and nfnetlink_queue. From Gao feng.
30) Implement RFC3168 ECN protection, from Hannes Frederic Sowa.
31) Support several new r8169 chips, from Hayes Wang.
32) Support tokenized interface identifiers in ipv6, from Daniel
Borkmann.
33) Use usbnet_link_change() helper in USB net driver, from Ming Lei.
34) Add 802.1ad vlan offload support, from Patrick McHardy.
35) Support mmap() based netlink communication, also from Patrick
McHardy.
36) Support HW timestamping in mlx4 driver, from Amir Vadai.
37) Rationalize AF_PACKET packet timestamping when transmitting, from
Willem de Bruijn and Daniel Borkmann.
38) Bring parity to what's provided by /proc/net/packet socket dumping
and the info provided by netlink socket dumping of AF_PACKET
sockets. From Nicolas Dichtel.
39) Fix peeking beyond zero sized SKBs in AF_UNIX, from Benjamin
Poirier"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1722 commits)
filter: fix va_list build error
af_unix: fix a fatal race with bit fields
bnx2x: Prevent memory leak when cnic is absent
bnx2x: correct reading of speed capabilities
net: sctp: attribute printl with __printf for gcc fmt checks
netlink: kconfig: move mmap i/o into netlink kconfig
netpoll: convert mutex into a semaphore
netlink: Fix skb ref counting.
net_sched: act_ipt forward compat with xtables
mlx4_en: fix a build error on 32bit arches
Revert "bnx2x: allow nvram test to run when device is down"
bridge: avoid OOPS if root port not found
drivers: net: cpsw: fix kernel warn on cpsw irq enable
sh_eth: use random MAC address if no valid one supplied
3c509.c: call SET_NETDEV_DEV for all device types (ISA/ISAPnP/EISA)
tg3: fix to append hardware time stamping flags
unix/stream: fix peeking with an offset larger than data in queue
unix/dgram: fix peeking with an offset larger than data in queue
unix/dgram: peek beyond 0-sized skbs
openvswitch: Remove unneeded ovs_netdev_get_ifindex()
...
|
|
Both phy-tegra-usb.c and ehci-tegra.c export symbols used by the other one,
which does not work if one of them or both are loadable modules, resulting
in an error like:
drivers/built-in.o: In function `utmi_phy_clk_disable':
drivers/usb/phy/phy-tegra-usb.c:302: undefined reference to `tegra_ehci_set_phcd'
drivers/built-in.o: In function `utmi_phy_clk_enable':
drivers/usb/phy/phy-tegra-usb.c:324: undefined reference to `tegra_ehci_set_phcd'
drivers/built-in.o: In function `utmi_phy_power_on':
drivers/usb/phy/phy-tegra-usb.c:447: undefined reference to `tegra_ehci_set_pts'
This turns the interface into a one-way dependency by letting the tegra ehci
driver pass two function pointers for callbacks that need to be called by
the phy driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Venu Byravarasu <vbyravarasu@nvidia.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ASoC: Updates for v3.10
A bunch of changes here, the most interesting one subsystem wise being
Morimoto-san's work to create snd_soc_component which doesn't do much
for now but will be pretty important going forwards:
- Add a new component object type which will form the basis of moving
to a more generic handling of SoC and off-SoC components, contributed
by Kuninori Morimoto.
- A fairly large set of cleanups for the dmaengine integration from
Lars-Peter Clausen, starting to move towards being able to have a
generic driver based on the library.
- Performance optimisations to DAPM from Ryo Tsutsui.
- Support for mixer control sharing in DAPM from Stephen Warren.
- Multiplatform ARM cleanups from Arnd Bergmann.
- New CODEC drivers for AK5385 and TAS5086 from Daniel Mack.
|
|
The link change is detected via the interrupt pipe, and bulk
pipes are responsible for transfering packets, so it is reasonable
to stop bulk transfer after link is reported as off.
Two adavantages may be obtained with stopping bulk transfer
after link becomes off:
- USB bus bandwidth is saved(USB bus is shared bus except for
USB3.0), for example, lots of 'IN' token packets and 'NYET'
handshake packets is transfered on 2.0 bus.
- probabaly power might be saved for usb host controller since
cancelling bulk transfer may disable the asynchronous schedule of
host controller.
With this patch, when link becomes off, about ~10% performance
boost can be found on bulk transfer of anther usb device which
is attached to same bus with the usbnet device, see below
test on next-20130410:
- read from usb mass storage(Sandisk Extreme USB 3.0) on pandaboard
with below command after unplugging ethernet cable:
dd if=/dev/sda iflag=direct of=/dev/null bs=1M count=800
- without the patch
1, 838860800 bytes (839 MB) copied, 36.2216 s, 23.2 MB/s
2, 838860800 bytes (839 MB) copied, 35.8368 s, 23.4 MB/s
3, 838860800 bytes (839 MB) copied, 35.823 s, 23.4 MB/s
4, 838860800 bytes (839 MB) copied, 35.937 s, 23.3 MB/s
5, 838860800 bytes (839 MB) copied, 35.7365 s, 23.5 MB/s
average: 23.6MB/s
- with the patch
1, 838860800 bytes (839 MB) copied, 32.3817 s, 25.9 MB/s
2, 838860800 bytes (839 MB) copied, 31.7389 s, 26.4 MB/s
3, 838860800 bytes (839 MB) copied, 32.438 s, 25.9 MB/s
4, 838860800 bytes (839 MB) copied, 32.5492 s, 25.8 MB/s
5, 838860800 bytes (839 MB) copied, 31.6178 s, 26.5 MB/s
average: 26.1MB/s
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch introduces the API of usbnet_link_change, so that
usbnet can handle link change centrally, which may help to
implement killing traffic URBs for saving USB bus bandwidth
and host controller power.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Felipe writes:
usb: patches for v3.10 merge window
Here is the big Gadget & PHY pull request. Many of us have
been really busy lately getting multiple drivers to a better
position.
Since this pull request is so large, I will divide it in sections
so it's easier to grasp what's included.
- cleanups:
. UDC drivers no longer touch gadget->dev, that's now udc-core
responsibility
. Many more UDC drivers converted to usb_gadget_map/unmap_request()
. UDC drivers no longer initialize DMA-related fields from gadget's
device structure
. UDC drivers don't touch gadget.dev.driver directly
. UDC drivers don't assign gadget.dev.release directly
. Removal of some unused DMA_ADDR_INVALID
. Introduction of CONFIG_USB_PHY
. All phy drivers have been moved to drivers/usb/phy and renamed to
a common naming scheme
. Fix PHY layer so it never returns a NULL pointer, also fix all
callers to avoid using IS_ERR_OR_NULL()
. Sparse fixes all over the place
. drivers/usb/otg/ has been deleted
. Marvel drivers (mv_udc, ehci-mv, mv_otg and mv_u3d) improved clock
usage
- new features:
. UDC core now provides a generic way for tracking and reporting
UDC's state (not attached, resuming, suspended, addressed,
default, etc)
. twl4030-usb learned that it shouldn't be enabled during init
. Full DT support for DWC3 has been implemented
. ab8500-usb learned about pinctrl framework
. nop PHY learned about DeviceTree and regulators
. DWC3 learned about suspend/resume
. DWC3 can now be compiled in host-only and gadget-only (as well as
DRD) configurations
. UVC now enables streaming endpoint based on negotiated speed
. isp1301 now implements the PHY API properly
. configfs-based interface for gadget drivers which will lead to
the removal of all code which just combines functions together
to build functional gadget drivers.
. f_serial and f_obex were converted to new configfs interface while
maintaining old interface around.
- non-critical fixes:
. UVC gadget driver got fixes for Endpoint usage and stream calculation
. ab8500-usb fixed unbalanced clock and regulator API usage
. twl4030-usb got a fix for when OMAP3 is booted with cable connected
. fusb300_udc got a fix for DMA usage
. UVC got fixes for two assertions of the USB Video Class Compliance
specification revision 1.1
. build warning issues caused by recent addition of __must_check to
regulator API
These are all changes which deserve a mention, all other changes are related
to these one or minor spelling fixes and other similar tasks.
Signed-of-by: Felipe Balbi <balbi@ti.com>
|
|
Back-merge for cleaning up usb-audio code the recent commit modified,
and further UAC2 autoclock patches.
|
|
|# modprobe dummy_hcd num=2
|# modprobe libcomposite
|# lsmod
|Module Size Used by
|libcomposite 31648 0
|dummy_hcd 19871 0
|# mkdir /sys/kernel/config/usb_gadget/oha
|# cd /sys/kernel/config/usb_gadget/oha
|# mkdir configs/def.1
|# mkdir configs/def.2
|# mkdir functions/acm.ttyS1
|# mkdir strings/0x1
|mkdir: cannot create directory `strings/0x1': Invalid argument
|# mkdir strings/0x409
|# mkdir strings/1033
|mkdir: cannot create directory `strings/1033': File exists
|# mkdir strings/1032
|# mkdir configs/def.1/strings/0x409
|# mkdir configs/def.2/strings/0x409
|#find . -ls
| 975 0 drwxr-xr-x 5 root root 0 Dec 23 17:40 .
| 978 0 drwxr-xr-x 4 root root 0 Dec 23 17:43 ./strings
| 4100 0 drwxr-xr-x 2 root root 0 Dec 23 17:43 ./strings/1032
| 995 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./strings/1032/serialnumber
| 996 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./strings/1032/product
| 997 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./strings/1032/manufacturer
| 2002 0 drwxr-xr-x 2 root root 0 Dec 23 17:41 ./strings/0x409
| 998 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./strings/0x409/serialnumber
| 999 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./strings/0x409/product
| 1000 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./strings/0x409/manufacturer
| 977 0 drwxr-xr-x 4 root root 0 Dec 23 17:41 ./configs
| 4081 0 drwxr-xr-x 3 root root 0 Dec 23 17:41 ./configs/def.2
| 4082 0 drwxr-xr-x 3 root root 0 Dec 23 17:42 ./configs/def.2/strings
| 2016 0 drwxr-xr-x 2 root root 0 Dec 23 17:42 ./configs/def.2/strings/0x409
| 1001 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./configs/def.2/strings/0x409/configuration
| 1002 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./configs/def.2/bmAttributes
| 1003 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./configs/def.2/MaxPower
| 979 0 drwxr-xr-x 3 root root 0 Dec 23 17:42 ./configs/def.1
| 980 0 drwxr-xr-x 3 root root 0 Dec 23 17:42 ./configs/def.1/strings
| 5122 0 drwxr-xr-x 2 root root 0 Dec 23 17:42 ./configs/def.1/strings/0x409
| 1004 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./configs/def.1/strings/0x409/configuration
| 1005 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./configs/def.1/bmAttributes
| 1006 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./configs/def.1/MaxPower
| 976 0 drwxr-xr-x 3 root root 0 Dec 23 17:41 ./functions
| 981 0 drwxr-xr-x 2 root root 0 Dec 23 17:41 ./functions/acm.ttyS1
| 1007 0 -r--r--r-- 1 root root 4096 Dec 23 17:43 ./functions/acm.ttyS1/port_num
| 1008 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./UDC
| 1009 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./bcdUSB
| 1010 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./bcdDevice
| 1011 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./idProduct
| 1012 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./idVendor
| 1013 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./bMaxPacketSize0
| 1014 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./bDeviceProtocol
| 1015 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./bDeviceSubClass
| 1016 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./bDeviceClass
|# cat functions/acm.ttyS1/port_num
|0
|# ls -lah /dev/ttyGS*
|crw-rw---T 1 root dialout 252, 0 Dec 23 17:41 /dev/ttyGS0
|
|# echo 0x1234 > idProduct
|# echo 0xabcd > idVendor
|# echo 1122 > strings/0x409/serialnumber
|# echo "The manufacturer" > strings/0x409/manufacturer
|# echo 1 > strings/1032/manufacturer
|# echo 1sa > strings/1032/product
|# echo tada > strings/1032/serialnumber
|echo "Primary configuration" > configs/def.1/strings/0x409/configuration
|# echo "Secondary configuration" > configs/def.2/strings/0x409/configuration
|# ln -s functions/acm.ttyS1 configs/def.1/
|# ln -s functions/acm.ttyS1 configs/def.2/
|find configs/def.1/ -ls
| 979 0 drwxr-xr-x 3 root root 0 Dec 23 17:49 configs/def.1/
| 6264 0 lrwxrwxrwx 1 root root 0 Dec 23 17:48 configs/def.1/acm.ttyS1 -> ../../../../usb_gadget/oha/functions/acm.ttyS1
| 980 0 drwxr-xr-x 3 root root 0 Dec 23 17:42 configs/def.1/strings
| 5122 0 drwxr-xr-x 2 root root 0 Dec 23 17:49 configs/def.1/strings/0x409
| 6284 0 -rw-r--r-- 1 root root 4096 Dec 23 17:47 configs/def.1/strings/0x409/configuration
| 6285 0 -rw-r--r-- 1 root root 4096 Dec 23 17:49 configs/def.1/bmAttributes
| 6286 0 -rw-r--r-- 1 root root 4096 Dec 23 17:49 configs/def.1/MaxPower
|
|echo 120 > configs/def.1/MaxPower
|
|# ls -lh /sys/class/udc/
|total 0
|lrwxrwxrwx 1 root root 0 Dec 23 17:50 dummy_udc.0 -> ../../devices/platform/dummy_udc.0/udc/dummy_udc.0
|lrwxrwxrwx 1 root root 0 Dec 23 17:50 dummy_udc.1 -> ../../devices/platform/dummy_udc.1/udc/dummy_udc.1
|# echo dummy_udc.0 > UDC
|# lsusb
|Bus 001 Device 002: ID abcd:1234 Unknown
|
|lsusb -d abcd:1234 -v
|Device Descriptor:
…
| idVendor 0xabcd Unknown
| idProduct 0x1234
| bcdDevice 3.06
| iManufacturer 1 The manufacturer
| iProduct 2
| iSerial 3 1122
| bNumConfigurations 2
…
|echo "" > UDC
v5…v6
- wired up strings with usb_gstrings_attach()
- add UDC attribe. Write "udc-name" will bind the gadget. Write an empty
string (it should contain \n since 0 bytes write get optimzed away)
will unbind the UDC from the gadget. The name of available UDCs can be
obtained from /sys/class/udc/
v4…v5
- string rework. This will add a strings folder incl. language code like
strings/409/manufacturer
as suggested by Alan.
- rebased ontop reworked functions.c which has usb_function_instance
which is used prior after "mkdir acm.instance" and can be directly
used for configuration via configfs.
v3…v4
- moved functions from the root folde down to the gadget as suggested
by Michał
- configs have now their own configs folder as suggested by Michał.
The folder is still name.bConfigurationValue where name becomes the
sConfiguration. Is this usefull should we just stilc
configs/bConfigurationValue/ ?
- added configfs support to the ACM function. The port_num attribute is
exported by f_acm. An argument has been added to the USB alloc
function to distinguish between "old" (use facm_configure() to
configure and configfs interface (expose a config_node).
The port_num is currently a dumb counter. It will
require some function re-work to make it work.
scheduled for v5:
- sym linking function into config.
v2…v3
- replaced one ifndef by ifdef as suggested by Micahał
- strstr()/strchr() function_make as suggested by Micahł
- replace [iSerialNumber|iProduct|iManufacturer] with
[sSerialNumber|sProduct|sManufacturer] as suggested by Alan
- added creation of config descriptors
v1…v2
- moved gadgets from configfs' root directory into /udcs/ within our
"usb_gadget" folder. Requested by Andrzej & Michał
- use a dot as a delimiter between function's name and its instance's name
as suggested by Michał
- renamed all config_item_type, configfs_group_operations, make_group,
drop_item as suggested by suggested by Andrzej to remain consisten
within this file and within other configfs users
- Since configfs.c and functions.c are now part of the udc-core module,
the module itself is now called udc. Also added a tiny ifdef around
init code becuase udc-core is subsys init and this is too early for
configfs in the built-in case. In the module case, we can only have
one init function.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch fixup below sparse errors
CHECK ${RENESAS_USB}/common.c
${RENESAS_USB}/common.c:313:17: error: incompatible types in conditional expression (different base types)
${RENESAS_USB}/common.c:322:17: error: incompatible types in conditional expression (different base types)
${RENESAS_USB}/common.c:384:17: error: incompatible types in conditional expression (different base types)
${RENESAS_USB}/common.c:524:9: error: incompatible types in conditional expression (different base types)
${RENESAS_USB}/common.c:545:9: error: incompatible types in conditional expression (different base types)
${RENESAS_USB}/common.c:574:9: error: incompatible types in conditional expression (different base types)
${RENESAS_USB}/common.c:606:9: error: incompatible types in conditional expression (different base types)
${RENESAS_USB}/mod_gadget.c:233:28: warning: symbol 'req_clear_feature' was not declared. Should it be static?
${RENESAS_USB}/mod_gadget.c:274:28: warning: symbol 'req_set_feature' was not declared. Should it be static?
${RENESAS_USB}/mod_gadget.c:375:28: warning: symbol 'req_get_status' was not declared. Should it be static?
[ balbi@ti.com : added three sparse fixes to mod_gadget.c ]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch (as1675) removes the CONFIG_USB_SUSPEND option, essentially
replacing it everywhere with CONFIG_PM_RUNTIME (except for one place
in hub.c, where it is replaced with CONFIG_PM because the code needs
to be used in both runtime and system PM). The net result is code
shrinkage and simplification.
There's very little point in keeping CONFIG_USB_SUSPEND because almost
everybody enables it. The few that don't will find that the usbcore
module has gotten somewhat bigger and they will have to take active
measures if they want to prevent hubs from being runtime suspended.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This lets us fix the build error that happens when these two trees are merged
together.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove the port MSR-wait queue now that all drivers have been migrated
to the tty-port queue.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add generic get_icount implementation that subdrivers relying on the
port interrupt counters can use.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add generic TIOCMIWAIT implementation which correctly handles hangup,
USB-device disconnect, does not rely on the deprecated sleep_on
functions and hence does not suffer from the races currently affecting
several usb-serial drivers.
This makes it much easier to add TIOCMIWAIT support to subdrivers as the
tricky details related to hangup and disconnect (e.g. atomicity, that
the private port data may have been freed when woken up, and waking up
processes at disconnect) have been handled once and for all.
To add support to a subdriver, simply set the tiocmiwait-port-operation
field, update the port icount fields and wake up any process sleeping on
the tty-port modem-status-change wait queue on changes.
Note that the tty-port initialised flag can be used to detect
disconnected as the port will be hung up as part of disconnect (and
cannot be reactivated due to the disconnected flag). However, as the
tty-port implementation currently wakes up processes before calling port
shutdown, the tty-hupping flag must also be checked to detect hangup for
now.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add tiocmiwait operation to struct usb_serial_driver.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove empty generic release implementation and make the release
callback non-mandatory (like attach, probe and disconnect).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove the now empty generic disconnect callback and make the disconnect
callback non-mandatory.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Userspace applications need to know the maximum supported message
size.
The cdc-wdm driver translates between a character device stream
and a message based protocol. Each message is transported as a
usb control message with no further encapsulation or syncronization.
Each read or write on the character device should translate to
exactly one usb control message to ensure that message boundaries
are kept intact. That means that the userspace application must
know the maximum message size supported by the device and driver,
making this size a vital part of the cdc-wdm character device API.
CDC WDM and CDC MBIM functions export the maximum supported
message size through CDC functional descriptors. The cdc-wdm and
cdc_mbim drivers will parse these descriptors and use the value
chosen by the device. The only current way for a userspace
application to retrive the value is by duplicating the descriptor
parsing. This is an unnecessary complex task, and application
writers are likely to postpone it, using a fixed value and adding
a "todo" item.
QMI functions have no way to tell the host what message size they
support. The qmi_wwan driver use a fixed value based on protocol
recommendations and observed device behaviour. Userspace
applications must know and hard code the same value. This scheme
will break if we ever encounter a QMI device needing a device
specific message size quirk. We are currently unable to support
such a device because using a non default size would break the
implicit userspace API.
The message size is currently a hidden attribute of the cdc-wdm
userspace API. Retrieving it is unnecessarily complex, increasing
the possibility of drivers and applications using different limits.
The resulting errors are hard to debug, and can only be replicated
on identical hardware.
Exporting the maximum message size from the driver simplifies the
task for the userspace application, and creates a unified
information source independent of device and function class. It also
serves to document that the message size is part of the cdc-wdm
userspace API.
This proposed API extension has been presented for the authors of
userspace applications and libraries using the current API: libmbim,
libqmi, uqmi, oFono and ModemManager. The replies were:
Aleksander Morgado:
"We do really need max message size for MBIM; and as you say, it may be
good to have the max message size info also for QMI, so the new ioctl
seems a good addition. So +1 from my side, for what it's worth."
Dan Williams:
"Yeah, +1 here. I'd prefer the sysfs file, but the fact that that
doesn't work for fd passing pretty much kills it."
No negative replies are so far received.
Cc: Aleksander Morgado <aleksander@lanedo.com>
Cc: Dan Williams <dcbw@redhat.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
xhci driver divides the root hub into two logical hubs which work
respectively for usb 2.0 and usb 3.0 devices. They are independent
devices in the usb core. But in the ACPI table, it's one device node
and all usb2.0 and usb3.0 ports are under it. Binding usb port with
its acpi node needs the raw port number which is reflected in the xhci
extended capabilities table. This patch is to add find_raw_port_number
callback to struct hc_driver(), fill it with xhci_find_raw_port_number()
which will return raw port number and add a wrap usb_hcd_find_raw_port_number().
Otherwise, refactor xhci_find_real_port_number(). Using
xhci_find_raw_port_number() to get real index in the HW port status
registers instead of scanning through the xHCI roothub port array.
This can help to speed up.
All addresses in xhci->usb2_ports and xhci->usb3_ports array are
kown good ports and don't include following bad ports in the extended
capabilities talbe.
(1) root port that doesn't have an entry
(2) root port with unknown speed
(3) root port that is listed twice and with different speeds.
So xhci_find_raw_port_number() will only return port num of good ones
and never touch bad ports above.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
|
Pull USB fixes from Greg Kroah-Hartman:
"Here are a number of USB fixes that resolve issues that have been
reported against 3.9-rc3."
* tag 'usb-3.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (37 commits)
USB: ti_usb_3410_5052: fix use-after-free in TIOCMIWAIT
USB: ssu100: fix use-after-free in TIOCMIWAIT
USB: spcp8x5: fix use-after-free in TIOCMIWAIT
USB: quatech2: fix use-after-free in TIOCMIWAIT
USB: pl2303: fix use-after-free in TIOCMIWAIT
USB: oti6858: fix use-after-free in TIOCMIWAIT
USB: mos7840: fix use-after-free in TIOCMIWAIT
USB: mos7840: fix broken TIOCMIWAIT
USB: mct_u232: fix use-after-free in TIOCMIWAIT
USB: io_ti: fix use-after-free in TIOCMIWAIT
USB: io_edgeport: fix use-after-free in TIOCMIWAIT
USB: ftdi_sio: fix use-after-free in TIOCMIWAIT
USB: f81232: fix use-after-free in TIOCMIWAIT
USB: cypress_m8: fix use-after-free in TIOCMIWAIT
USB: ch341: fix use-after-free in TIOCMIWAIT
USB: ark3116: fix use-after-free in TIOCMIWAIT
USB: serial: add modem-status-change wait queue
USB: serial: fix interface refcounting
USB: io_ti: fix get_icount for two port adapters
USB: garmin_gps: fix memory leak on disconnect
...
|
|
Add modem-status-change wait queue to struct usb_serial_port that
subdrivers can use to implement TIOCMIWAIT.
Currently subdrivers use a private wait queue which may have been
released when waking up after device disconnected.
Note that we're adding a new wait queue rather than reusing the tty-port
one as we do not want to get woken up at hangup (yet).
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Building a kernel for imx_v4_v5_defconfig with CONFIG_USB_ULPI disabled, results
in the following error:
arch/arm/mach-imx/built-in.o: In function 'pca100_init':
platform-mx2-emma.c:(.init.text+0x6788): undefined reference to 'otg_ulpi_create'
platform-mx2-emma.c:(.init.text+0x682c): undefined reference to 'mxc_ulpi_access_ops'
Fix this by providing a no-op definition of *otg_ulpi_create for the case when
CONFIG_USB_ULPI is not defined.
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Pull networking fixes from David Miller:
1) Fix ARM BPF JIT handling of negative 'k' values, from Chen Gang.
2) Insufficient space reserved for bridge netlink values, fix from
Stephen Hemminger.
3) Some dst_neigh_lookup*() callers don't interpret error pointer
correctly, fix from Zhouyi Zhou.
4) Fix transport match in SCTP active_path loops, from Xugeng Zhang.
5) Fix qeth driver handling of multi-order SKB frags, from Frank
Blaschka.
6) fec driver is missing napi_disable() call, resulting in crashes on
unload, from Georg Hofmann.
7) Don't try to handle PMTU events on a listening socket, fix from Eric
Dumazet.
8) Fix timestamp location calculations in IP option processing, from
David Ward.
9) FIB_TABLE_HASHSZ setting is not controlled by the correct kconfig
tests, from Denis V Lunev.
10) Fix TX descriptor push handling in SFC driver, from Ben Hutchings.
11) Fix isdn/hisax and tulip/de4x5 kconfig dependencies, from Arnd
Bergmann.
12) bnx2x statistics don't handle 4GB rollover correctly, fix from
Maciej Żenczykowski.
13) Openvswitch bug fixes for vport del/new error reporting, missing
genlmsg_end() call in netlink processing, and mis-parsing of
LLC/SNAP ethernet types. From Rich Lane.
14) SKB pfmemalloc state should only be propagated from the head page of
a compound page, fix from Pavel Emelyanov.
15) Fix link handling in tg3 driver for 5715 chips when autonegotation
is disabled. From Nithin Sujir.
16) Fix inverted test of cpdma_check_free_tx_desc return value in
davinci_emac driver, from Mugunthan V N.
17) vlan_depth is incorrectly calculated in skb_network_protocol(), from
Li RongQing.
18) Fix probing of Gobi 1K devices in qmi_wwan driver, and fix NCM
device mode backwards compat in cdc_ncm driver. From Bjørn Mork.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (52 commits)
inet: limit length of fragment queue hash table bucket lists
qeth: Fix scatter-gather regression
qeth: Fix invalid router settings handling
qeth: delay feature trace
tcp: dont handle MTU reduction on LISTEN socket
bnx2x: fix occasional statistics off-by-4GB error
vhost/net: fix heads usage of ubuf_info
bridge: Add support for setting BR_ROOT_BLOCK flag.
bnx2x: add missing napi deletion in error path
drivers: net: ethernet: ti: davinci_emac: fix usage of cpdma_check_free_tx_desc()
ethernet/tulip: DE4x5 needs VIRT_TO_BUS
isdn: hisax: netjet requires VIRT_TO_BUS
net: cdc_ncm, cdc_mbim: allow user to prefer NCM for backwards compatibility
rtnetlink: Mask the rta_type when range checking
Revert "ip_gre: make ipgre_tunnel_xmit() not parse network header as IP unconditionally"
Fix dst_neigh_lookup/dst_neigh_lookup_skb return value handling bug
smsc75xx: configuration help incorrectly mentions smsc95xx
net: fec: fix missing napi_disable call
net: fec: restart the FEC when PHY speed changes
skb: Propagate pfmemalloc on skb from head page only
...
|
|
Update irq handling code to notify all possible link status changes of
AB8500 and AB8505 to the ux500-musb glue driver. The additional event
codes will be used for pm-runtime implementation, and are defined in a
separate ux500-specific header.
This also modify the irq registration code to use devm_* helpers and
drop all non necessary fail path code.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
in cases where PHY layer isn't enabled, we want
to still return an error code (actually an error
pointer) so that our users don't need to cope with
either error pointer of NULL.
This will simplify users as below:
- return IS_ERR(phy) ? PTR_ERR(phy) : -ENODEV;
+ return PTR_ERR(phy);
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
return -EPROBE_DEFER from dwc3_omap_mailbox in dwc3-omap.c, if the probe of
dwc3-omap has not yet been executed or failed.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
Ming Lei
Linus Torvalds
Alexander Shishkin
Peter Chen
Stephen Warren
Sascha Hauer
Michael Grzeschik
Greg Kroah-Hartman
Olof Johansson
Greg Kroah-Hartman
Sergei Shtylyov
Thomas Pugliese
Venu Byravarasu
Johan Hovold
Robert P. J. Day
Dan Williams
Arnd Bergmann
Takashi Iwai
Sebastian Andrzej Siewior
Kuninori Morimoto
Alan Stern
Bjørn Mork
Lan Tianyu
Fabio Estevam
Fabio Baltieri
Felipe Balbi
Kishon Vijay Abraham I