| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This patch adds the support for the OMAP IOMMUs to be suspended
during the auto suspend/resume of the OMAP remoteproc devices. The
remote processors are auto suspended after a certain time of idle
or inactivity period. This is done by introducing two new API,
omap_iommu_domain_deactivate() and omap_iommu_domain_activate()
to allow the client users/master devices of the IOMMU devices to
deactivate & activate the IOMMU devices from their runtime
suspend/resume operations. There is no API exposed by the IOMMU
layer at present, and so these new API are added directly in the
OMAP IOMMU driver to minimize framework changes.
The API simply decrements and increments the runtime usage count
of the IOMMU devices and let the context be saved/restored using
the existing runtime pm callbacks.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Add two new platform data ops to allow the OMAP iommu driver to
be able to invoke the omap_device_enable and omap_device_idle
from within the driver. These are being added to streamline the
sequence between managing the hard reset lines and the clocks
during the suspend path, as the default device pm_domain callback
sequences in omap_device layer are not conducive for the OMAP
IOMMU driver.
This could have been done by expanding the existing pdata ops
for reset management (like in the OMAP remoteproc driver), but
this was chosen to avoid adding additional code in the separate
file in the mach-omap2 layer.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Support has been added to the OMAP IOMMU driver to fix a boot hang
issue on OMAP remoteprocs with AMMU/Unicache, caused by an improper
AMMU/Unicache state upon initial deassertion of the processor reset.
The issue is described in detail in the next three paragraphs.
All the Cortex M3/M4 IPU processor subsystems in OMAP SoCs have a
AMMU/Unicache IP that dictates the memory attributes for addresses
seen by the processor cores. The AMMU/Unicache is configured/enabled
by the SCACHE_CONFIG.BYPASS bit - a value of 1 enables the cache and
mandates all addresses accessed by M3/M4 be defined in the AMMU. This
bit is not programmable from the host processor. The M3/M4 boot
sequence starts out with the AMMU/Unicache in disabled state, and
SYS/BIOS programs the AMMU regions and enables the Unicache during
one of its initial boot steps. This SCACHE_CONFIG.BYPASS bit is
however enabled by default whenever a RET reset is applied to the IP,
irrespective of whether it was previously enabled or not. The AMMU
registers lose their context whenever this reset is applied. The reset
is effective as long as the MMU portion of the subsystem is enabled
and clocked. This behavior is common to all the IPU and DSP subsystems
that have an AMMU/Unicache.
The IPU boot sequence involves enabling and programming the MMU, and
loading the processor and releasing the reset(s) for the processor.
The PM setup code currently sets the target state for most of the
power domains to RET. The L2 MMU can be enabled, programmed and
accessed properly just fine with the domain in hardware supervised
mode, while the power domain goes through a RET->ON->RET transition
during the programming sequence. However, the ON->RET transition
asserts a RET reset, and the SCACHE_CONFIG.BYPASS bit gets auto-set.
An AMMU fault is thrown immediately when the M3/M4 core's reset is
released since the first instruction address itself will not be
defined in any valid AMMU regions. The ON->RET transition happens
automatically on the power domain after enabling the iommu due to
the hardware supervised mode.
This patch adds and invokes the .set_pwrdm_constraint pdata ops, if
present, during the OMAP IOMMU enable and disable functions to resolve
the above boot hang issue. The ops will allow to invoke a mach-omap2
layer API pwrdm_set_next_pwrst() in a multi-arch kernel environment.
The ops also returns the current power domain state while enforcing
the constraint so that the driver can store it and use it to set back
the power domain state while releasing the constraint. The pdata ops
implementation restricts the target power domain to ON during enable,
and back to the original power domain state during disable, and thereby
eliminating the conditions for the boot issue. The implementation is
effective only when the original power domain state is either RET or
OFF, and is a no-op when it is ON or INACTIVE.
The .set_pwrdm_constraint ops need to be plugged in pdata-quirks
for the affected remote processors to be able to boot properly.
Note that the current issue is seen only on kernels with the affected
power domains programmed to enter RET. For eg., IPU1 on DRA7xx is in a
separate domain and is susceptible to this bug, while the IPU2 subsystem
is within CORE power domain, and CORE RET is not supported on this SoC.
IPUs on OMAP4 and OMAP5 are also susceptible since they are in CORE power
domain, and CORE RET is a valid power target on these SoCs.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Re-factore the logic for activate/deactivate guest virtual APIC mode (GAM)
into helper functions, and export them for other drivers (e.g. SVM).
to support run-time activate/deactivate of SVM AVIC.
Cc: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
KVM/arm fixes for 5.3
- A bunch of switch/case fall-through annotation, fixing one actual bug
- Fix PMU reset bug
- Add missing exception class debug strings
|
|
Moritz writes:
FPGA Manager changes for 5.4-rc1
Here is the first set of changes for the 5.4-rc1 merge window.
They're all more or less cleanup patches:
- Carlos' patch addresses a checkpatch warning
- My first patch changes the return type of a function to align it with
the fact that nothing checks the return value and it uncoditionally
returned 0 anyways
- My second patch somehow fell through the cracks before and cleans up
the FPGA bridge bindings by consolidating them instead of repeating
the same paragraph over and over again.
All of these patches have been in the last few linux-next releases
without issues.
Signed-off-by: Moritz Fischer <mdf@kernel.org>
* tag 'fpga-for-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mdf/linux-fpga:
dt-bindings: fpga: Consolidate bridge properties
fpga: altera-pr-ip: Make alt_pr_unregister function void
fpga: altera-cvp: Fix function definition argument
|
|
Fix the warnings for parameter named as "driver" instead of the actual "drv"
in the comments as reported by the kbuild robot.
Reported-by: kbuild test robot <lkp@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20190809102033.28463-1-suzuki.poulose@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Secure Encrypted Virtualization is an x86-specific feature, so it shouldn't
appear in generic kernel code because it forces non-x86 architectures to
define the sev_active() function, which doesn't make a lot of sense.
To solve this problem, add an x86 elfcorehdr_read() function to override
the generic weak implementation. To do that, it's necessary to make
read_from_oldmem() public so that it can be used outside of vmcore.c.
Also, remove the export for sev_active() since it's only used in files that
won't be built as modules.
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.ibm.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Lianbo Jiang <lijiang@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190806044919.10622-6-bauerman@linux.ibm.com
|
|
Now that generic code doesn't reference them, move sme_active() and
sme_me_mask to x86's <asm/mem_encrypt.h>.
Also remove the export for sme_active() since it's only used in files that
won't be built as modules. sme_me_mask on the other hand is used in
arch/x86/kvm/svm.c (via __sme_set() and __psp_pa()) which can be built as a
module so its export needs to stay.
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.ibm.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190806044919.10622-5-bauerman@linux.ibm.com
|
|
Introduce the clk_hw_set_parent() provider call to change parent of
a clock by using the clk_hw pointers.
This eases the clock reparenting from clock rate notifiers and
implementing DVFS with simpler code avoiding the boilerplates
functions as __clk_lookup(clk_hw_get_name()) then clk_set_parent().
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
|
|
Migrating the TI nspire calculators to use the PL111 driver for
framebuffer requires grayscale support for the elder panel
which uses 8bit grayscale only.
DRM does not support 8bit grayscale framebuffers in memory,
but by defining the bus format to be MEDIA_BUS_FMT_Y8_1X8 we
can get the hardware to turn on a grayscaling feature and
convert the RGB framebuffer to grayscale for us.
Cc: Daniel Tang <dt.tangr@gmail.com>
Cc: Fabian Vogt <fabian@ritter-vogt.de>
Tested-by: Fabian Vogt <fabian@ritter-vogt.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190805085847.25554-2-linus.walleij@linaro.org
|
|
drm-misc-next for 5.4:
UAPI Changes:
- HDCP: Add a Content protection type property
Cross-subsystem Changes:
Core Changes:
- Continue to rework the include dependencies
- fb: Remove the unused drm_gem_fbdev_fb_create function
- drm-dp-helper: Make the link rate calculation more tolerant to
non-explicitly defined, yet supported, rates
- fb-helper: Map DRM client buffer only when required, and instanciate a
shadow buffer when the device has a dirty function or says so
- connector: Add a helper to link the DDC adapter used by that connector to
the userspace
- vblank: Switch from DRM_WAIT_ON to wait_event_interruptible_timeout
- dma-buf: Fix a stack corruption
- ttm: Embed a drm_gem_object struct to make ttm_buffer_object a
superclass of GEM, and convert drivers to use it.
- hdcp: Improvements to report the content protection type to the
userspace
Driver Changes:
- Remove drm_gem_prime_import/export from being defined in the drivers
- Drop DRM_AUTH usage from drivers
- Continue to drop drmP.h
- Convert drivers to the connector ddc helper
- ingenic: Add support for more panel-related cases
- komeda: Support for dual-link
- lima: Reduce logging
- mpag200: Fix the cursor support
- panfrost: Export GPU features register to userspace through an ioctl
- pl111: Remove the CLD pads wiring support from the DT
- rockchip: Rework to use DRM PSR helpers, fix a bug in the VOP_WIN_GET
macro
- sun4i: Improve support for color encoding and range
- tinydrm: Rework SPI support, improve MIPI-DBI support, move to drm/tiny
- vkms: Rework of the CRC tracking
- bridges:
- sii902x: Add support for audio graph card
- tc358767: Rework AUX data handling code
- ti-sn65dsi86: Add Debugfs and proper DSI mode flags support
- panels
- Support for GiantPlus GPM940B0, Sharp LQ070Y3DG3B, Ortustech
COM37H3M, Novatek NT39016, Sharp LS020B1DD01D, Raydium RM67191,
Boe Himax8279d, Sharp LD-D5116Z01B
- Conversion of the device tree bindings to the YAML description
- jh057n00900: Rework the enable / disable path
- fbdev:
- ssd1307fb: Support more devices based on that controller
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190808121423.xzpedzkpyecvsiy4@flea
|
|
sk_validate_xmit_skb() and drivers depend on the sk member of
struct sk_buff to identify segments requiring encryption.
Any operation which removes or does not preserve the original TLS
socket such as skb_orphan() or skb_clone() will cause clear text
leaks.
Make the TCP socket underlying an offloaded TLS connection
mark all skbs as decrypted, if TLS TX is in offload mode.
Then in sk_validate_xmit_skb() catch skbs which have no socket
(or a socket with no validation) and decrypted flag set.
Note that CONFIG_SOCK_VALIDATE_XMIT, CONFIG_TLS_DEVICE and
sk->sk_validate_xmit_skb are slightly interchangeable right now,
they all imply TLS offload. The new checks are guarded by
CONFIG_TLS_DEVICE because that's the option guarding the
sk_buff->decrypted member.
Second, smaller issue with orphaning is that it breaks
the guarantee that packets will be delivered to device
queues in-order. All TLS offload drivers depend on that
scheduling property. This means skb_orphan_partial()'s
trick of preserving partial socket references will cause
issues in the drivers. We need a full orphan, and as a
result netem delay/throttling will cause all TLS offload
skbs to be dropped.
Reusing the sk_buff->decrypted flag also protects from
leaking clear text when incoming, decrypted skb is redirected
(e.g. by TC).
See commit 0608c69c9a80 ("bpf: sk_msg, sock{map|hash} redirect
through ULP") for justification why the internal flag is safe.
The only location which could leak the flag in is tcp_bpf_sendmsg(),
which is taken care of by clearing the previously unused bit.
v2:
- remove superfluous decrypted mark copy (Willem);
- remove the stale doc entry (Boris);
- rely entirely on EOR marking to prevent coalescing (Boris);
- use an internal sendpages flag instead of marking the socket
(Boris).
v3 (Willem):
- reorganize the can_skb_orphan_partial() condition;
- fix the flag leak-in through tcp_bpf_sendmsg.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This enum is only used in drivers/usb/dwc3/dwc3-omap3.c
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Implement the RSS functionality and add the corresponding callbacks in
XGMAC core.
Changes from v1:
- Do not use magic constants (Jakub)
- Use ethtool_rxfh_indir_default() (Jakub)
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When GRO decides not to coalesce a packet, in napi_frags_finish(), instead
of passing it to the stack immediately, place it on a list in the napi
struct. Then, at flush time (napi_complete_done(), napi_poll(), or
napi_busy_loop()), call netif_receive_skb_list_internal() on the list.
We'd like to do that in napi_gro_flush(), but it's not called if
!napi->gro_bitmask, so we have to do it in the callers instead. (There are
a handful of drivers that call napi_gro_flush() themselves, but it's not
clear why, or whether this will affect them.)
Because a full 64 packets is an inefficiently large batch, also consume the
list whenever it exceeds gro_normal_batch, a new net/core sysctl that
defaults to 8.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Supported ports in ethtool <eth1> are displayed based on media type.
For media type fibre and twinaxial, port type is "FIBRE". Media type
Base-T is "TP" and media KR is "Backplane".
V1->V2:
Corrected the subject.
Signed-off-by: Rahul Verma <rahulv@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
device_node_to_regmap() is exactly like syscon_node_to_regmap(), but it
does not check that the node is compatible with "syscon", and won't
attach the first clock it finds to the regmap.
The rationale behind this, is that one device node with a standard
compatible string "foo,bar" can be covered by multiple drivers sharing a
regmap, or by a single driver doing all the job without a regmap, but
these are implementation details which shouldn't reflect on the
devicetree.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Cc: linux-mips@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Cc: od@zcrc.me
Cc: Mathieu Malaterre <malat@debian.org>
|
|
Convert pci_resource_to_user() to a weak function so the existing
architecture-specific implementations will automatically override the
generic one. This allows us to remove HAVE_ARCH_PCI_RESOURCE_TO_USER
definitions and avoid the conditional compilation for this single function.
Link: https://lore.kernel.org/r/20190729101401.28068-1-efremov@linux.com
Link: https://lore.kernel.org/r/20190729101401.28068-2-efremov@linux.com
Link: https://lore.kernel.org/r/20190729101401.28068-3-efremov@linux.com
Link: https://lore.kernel.org/r/20190729101401.28068-4-efremov@linux.com
Link: https://lore.kernel.org/r/20190729101401.28068-5-efremov@linux.com
Link: https://lore.kernel.org/r/20190729101401.28068-6-efremov@linux.com
Signed-off-by: Denis Efremov <efremov@linux.com>
[bhelgaas: squash into one commit]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Paul Burton <paul.burton@mips.com> # MIPS
|
|
The TLS progress params context WQE should not include an
Eth segment, drop it.
In addition, align the tls_progress_params layout with the
HW specification document:
- fix the tisn field name.
- remove the valid bit.
Fixes: a12ff35e0fb7 ("net/mlx5: Introduce TLS TX offload hardware bits and structures")
Fixes: d2ead1f360e8 ("net/mlx5e: Add kTLS TX HW offload support")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Fix the used constants for TLS TIS opmods, per the HW specification.
Fixes: a12ff35e0fb7 ("net/mlx5: Introduce TLS TX offload hardware bits and structures")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
According to Section 3.5 of the "Intel Low Power S0 Idle" document [1],
Function 5 of the LPS0 _DSM is expected to be invoked when the system
configuration matches the criteria for entering the target low-power
state of the platform. In particular, this means that all devices
should be suspended and in low-power states already when that function
is invoked.
This is not the case currently, however, because Function 5 of the
LPS0 _DSM is invoked by it before the "noirq" phase of device suspend,
which means that some devices may not have been put into low-power
states yet at that point. That is a consequence of the previous
design of the suspend-to-idle flow that allowed the "noirq" phase of
device suspend and the "noirq" phase of device resume to be carried
out for multiple times while "suspended" (if any spurious wakeup
events were detected) and the point of the LPS0 _DSM Function 5
invocation was chosen so as to call it (and LPS0 _DSM Function 6
analogously) once per suspend-resume cycle (regardless of how many
times the "noirq" phases of device suspend and resume were carried
out while "suspended").
Now that the suspend-to-idle flow has been redesigned to carry out
the "noirq" phases of device suspend and resume once in each cycle,
the code can be reordered to follow the specification that it is
based on more closely.
For this purpose, add ->prepare_late and ->restore_early platform
callbacks for suspend-to-idle, to be executed, respectively, after
the "noirq" phase of suspending devices and before the "noirq"
phase of resuming them and make ACPI use them for the invocation
of LPS0 _DSM functions as appropriate.
While at it, move the LPS0 entry requirements check to be made
before invoking Functions 3 and 5 of the LPS0 _DSM (also once
per cycle) as follows from the specification [1].
Link: https://uefi.org/sites/default/files/resources/Intel_ACPI_Low_Power_S0_Idle.pdf # [1]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
|
|
System firmware advertises the address of the 'Runtime
Configuration Interface table version 2 (RCI2)' via
an EFI Configuration Table entry. This code retrieves the RCI2
table from the address and exports it to sysfs as a binary
attribute 'rci2' under /sys/firmware/efi/tables directory.
The approach adopted is similar to the attribute 'DMI' under
/sys/firmware/dmi/tables.
RCI2 table contains BIOS HII in XML format and is used to populate
BIOS setup page in Dell EMC OpenManage Server Administrator tool.
The BIOS setup page contains BIOS tokens which can be configured.
Signed-off-by: Narendra K <Narendra.K@dell.com>
Reviewed-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
|
|
The SAL systab is an Itanium specific EFI configuration table, so
move its handling into arch/ia64 where it belongs.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
|
|
The SGI UV UEFI machines are tightly coupled to the x86 architecture
so there is no need to keep any awareness of its existence in the
generic EFI layer, especially since we already have the infrastructure
to handle arch-specific configuration tables, and were even already
using it to some extent.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
|
|
The function efi_is_table_address() and the associated array of table
pointers is specific to x86. Since we will be adding some more x86
specific tables, let's move this code out of the generic code first.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
|
|
The patch moving bits into mutex.c was a little too much; by also
moving struct mutex_waiter a few less common CONFIGs would no longer
build.
Fixes: 5f35d5a66b3e ("locking/mutex: Make __mutex_owner static to mutex.c")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
|
|
The UWB and wusbcore code is long obsolete, so let us just move the code
out of the real part of the kernel and into the drivers/staging/
location with plans to remove it entirely in a few releases.
Link: https://lore.kernel.org/r/20190806101509.GA11280@kroah.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The following functions:
- clk_bulk_enable()
- clk_bulk_prepare()
- clk_bulk_disable()
- clk_bulk_unprepare()
already expect const clk_bulk_data * as a second parameter, however
their no-op version have mismatching prototypes that don't. Fix that.
While at it, constify the second argument of clk_bulk_prepare_enable()
and clk_bulk_disable_unprepare(), since the functions they are
comprised of already accept const clk_bulk_data *.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-clk@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lkml.kernel.org/r/20190717145651.17250-1-andrew.smirnov@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Reference counters are preferred to use refcount_t instead of
atomic_t.
This is because the implementation of refcount_t can prevent
overflows and detect possible use-after-free.
So convert atomic_t ref counters to refcount_t.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Acked-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
All users pass PAGE_SIZE here, and if we wanted to support single entries
for huge pages we should really just add a HMM_FAULT_HUGEPAGE flag instead
that uses the huge page size instead of having the caller calculate that
size once, just for the hmm code to verify it.
Link: https://lore.kernel.org/r/20190806160554.14046-8-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
The start, end and page_shift values are all saved in the range structure,
so we might as well use that for argument passing.
Link: https://lore.kernel.org/r/20190806160554.14046-7-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Link: https://lore.kernel.org/r/20190806160554.14046-6-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Booting a large arm64 server (HiSi D05) leads to the following
shouting at boot time:
[ 20.722132] debugfs: File 'irqchip@(____ptrval____)-3' in directory 'domains' already present!
[ 20.730851] debugfs: File 'irqchip@(____ptrval____)-3' in directory 'domains' already present!
[ 20.739560] debugfs: File 'irqchip@(____ptrval____)-3' in directory 'domains' already present!
[ 20.748267] debugfs: File 'irqchip@(____ptrval____)-3' in directory 'domains' already present!
[ 20.756975] debugfs: File 'irqchip@(____ptrval____)-3' in directory 'domains' already present!
[ 20.765683] debugfs: File 'irqchip@(____ptrval____)-3' in directory 'domains' already present!
[ 20.774391] debugfs: File 'irqchip@(____ptrval____)-3' in directory 'domains' already present!
and many more... Evidently, we expect something a bit more informative
than ____ptrval____, and certainly we want all of our domains, not just
the first one.
For that, turn the %p used to generate the fwnode name into something
that won't be repainted (%pa). Given that we've now fixed all users to
pass a pointer to a PA, it will actually do the right thing.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>
|
|
The function override_function_with_return() is defined separately for
each architecture and every architecture's definition is almost same
with each other. E.g. x86 and powerpc both define function in its own
asm/error-injection.h header and override_function_with_return() has
the same definition, the only difference is that x86 defines an extra
function just_return_func() but it is specific for x86 and is only used
by x86's override_function_with_return(), so don't need to export this
function.
This patch consolidates override_function_with_return() definition into
asm-generic/error-injection.h header, thus all architectures can use the
common definition. As result, the architecture specific headers are
removed; the include/linux/error-injection.h header also changes to
include asm-generic/error-injection.h header rather than architecture
header, furthermore, it includes linux/compiler.h for successful
compilation.
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Now that the driver core supports dev_groups for individual drivers,
expose that pointer to struct usb_device_driver to make it easier for USB
drivers to also use it.
Yes, users of usb_device_driver are much rare, but there are instances
already that use custom sysfs files, so adding this support will make
things easier for those drivers. usbip is one example, hubs might be
another one.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20190806144502.17792-3-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Now that the driver core supports dev_groups for individual drivers,
expose that pointer to struct usb_driver to make it easier for USB
drivers to also use it.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20190806144502.17792-2-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
MT7629 is an ARM platform SoC which has the same PCIe IP as MT7622.
The HW default value of its PCI host controller Device ID is invalid,
fix it to match the hardware implementation.
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
[lorenzo.pieralisi@arm.com: commit log/minor spelling update]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
|
|
Just minor overlapping changes in the conflicts here.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
"Yeah I should have sent a pull request last week, so there is a lot
more here than usual:
1) Fix memory leak in ebtables compat code, from Wenwen Wang.
2) Several kTLS bug fixes from Jakub Kicinski (circular close on
disconnect etc.)
3) Force slave speed check on link state recovery in bonding 802.3ad
mode, from Thomas Falcon.
4) Clear RX descriptor bits before assigning buffers to them in
stmmac, from Jose Abreu.
5) Several missing of_node_put() calls, mostly wrt. for_each_*() OF
loops, from Nishka Dasgupta.
6) Double kfree_skb() in peak_usb can driver, from Stephane Grosjean.
7) Need to hold sock across skb->destructor invocation, from Cong
Wang.
8) IP header length needs to be validated in ipip tunnel xmit, from
Haishuang Yan.
9) Use after free in ip6 tunnel driver, also from Haishuang Yan.
10) Do not use MSI interrupts on r8169 chips before RTL8168d, from
Heiner Kallweit.
11) Upon bridge device init failure, we need to delete the local fdb.
From Nikolay Aleksandrov.
12) Handle erros from of_get_mac_address() properly in stmmac, from
Martin Blumenstingl.
13) Handle concurrent rename vs. dump in netfilter ipset, from Jozsef
Kadlecsik.
14) Setting NETIF_F_LLTX on mac80211 causes complete breakage with
some devices, so revert. From Johannes Berg.
15) Fix deadlock in rxrpc, from David Howells.
16) Fix Kconfig deps of enetc driver, we must have PHYLIB. From Yue
Haibing.
17) Fix mvpp2 crash on module removal, from Matteo Croce.
18) Fix race in genphy_update_link, from Heiner Kallweit.
19) bpf_xdp_adjust_head() stopped working with generic XDP when we
fixes generic XDP to support stacked devices properly, fix from
Jesper Dangaard Brouer.
20) Unbalanced RCU locking in rt6_update_exception_stamp_rt(), from
David Ahern.
21) Several memory leaks in new sja1105 driver, from Vladimir Oltean"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (214 commits)
net: dsa: sja1105: Fix memory leak on meta state machine error path
net: dsa: sja1105: Fix memory leak on meta state machine normal path
net: dsa: sja1105: Really fix panic on unregistering PTP clock
net: dsa: sja1105: Use the LOCKEDS bit for SJA1105 E/T as well
net: dsa: sja1105: Fix broken learning with vlan_filtering disabled
net: dsa: qca8k: Add of_node_put() in qca8k_setup_mdio_bus()
net: sched: sample: allow accessing psample_group with rtnl
net: sched: police: allow accessing police->params with rtnl
net: hisilicon: Fix dma_map_single failed on arm64
net: hisilicon: fix hip04-xmit never return TX_BUSY
net: hisilicon: make hip04_tx_reclaim non-reentrant
tc-testing: updated vlan action tests with batch create/delete
net sched: update vlan action for batched events operations
net: stmmac: tc: Do not return a fragment entry
net: stmmac: Fix issues when number of Queues >= 4
net: stmmac: xgmac: Fix XGMAC selftests
be2net: disable bh with spin_lock in be_process_mcc
net: cxgb3_main: Fix a resource leak in a error path in 'init_one()'
net: ethernet: sun4i-emac: Support phy-handle property for finding PHYs
net: bridge: move default pvid init/deinit to NETDEV_REGISTER/UNREGISTER
...
|
|
Fixes: c8424e776b09 ("MODSIGN: Export module signature definitions")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
|
|
Now that blk_rq_map_kern can map both kmem and vmem, move internal
metadata mapping down to the lower level driver.
Reviewed-by: Javier González <javier@javigon.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hans Holmberg <hans@owltronix.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Move the redundant sync handling interface and wait for a completion in
the lightnvm core instead.
Reviewed-by: Javier González <javier@javigon.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hans Holmberg <hans@owltronix.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
__mutex_owner() should only be used by the mutex api's.
So, to put this restiction let's move the __mutex_owner()
function definition from linux/mutex.h to mutex.c file.
There exist functions that uses __mutex_owner() like
mutex_is_locked() and mutex_trylock_recursive(), So
to keep legacy thing intact move them as well and
export them.
Move mutex_waiter structure also to keep it private to the
file.
Signed-off-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: mingo@redhat.com
Cc: will@kernel.org
Link: https://lkml.kernel.org/r/1564585504-3543-1-git-send-email-mojha@codeaurora.org
|
|
Currently rwsems is the only locking primitive that lacks this
debug feature. Add it under CONFIG_DEBUG_RWSEMS and do the magic
checking in the locking fastpath (trylock) operation such that
we cover all cases. The unlocking part is pretty straightforward.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Waiman Long <longman@redhat.com>
Cc: mingo@kernel.org
Cc: Davidlohr Bueso <dave@stgolabs.net>
Link: https://lkml.kernel.org/r/20190729044735.9632-1-dave@stgolabs.net
|
|
dev_groups added to struct driver
Persistent tag for others to pull this branch from
This is the first patch in a longer series that adds the ability for the
driver core to create and remove a list of attribute groups
automatically when the device is bound/unbound from a specific driver.
See:
https://lore.kernel.org/r/20190731124349.4474-2-gregkh@linuxfoundation.org
for details on this patch, and examples of how to use it in other
drivers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
IMA will need to verify a PKCS#7 signature which has already been parsed.
For this reason, factor out the code which does that from
verify_pkcs7_signature() into a new function which takes a struct
pkcs7_message instead of a data buffer.
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.ibm.com>
Reviewed-by: Mimi Zohar <zohar@linux.ibm.com>
Cc: David Howells <dhowells@redhat.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
|
|
IMA will use the module_signature format for append signatures, so export
the relevant definitions and factor out the code which verifies that the
appended signature trailer is valid.
Also, create a CONFIG_MODULE_SIG_FORMAT option so that IMA can select it
and be able to use mod_check_sig() without having to depend on either
CONFIG_MODULE_SIG or CONFIG_MODULES.
s390 duplicated the definition of struct module_signature so now they can
use the new <linux/module_signature.h> header instead.
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.ibm.com>
Acked-by: Jessica Yu <jeyu@kernel.org>
Reviewed-by: Philipp Rudo <prudo@linux.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
|
|
Add new attribute named "serial_number" as a standard interface for
user space to acquire the serial number of the device.
For ST-Ericsson SoCs this is exposed by the cryptically named "soc_id"
attribute, but this provides a human readable standardized name for this
property.
Tested-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vaishali Thakkar <vaishali.thakkar@linaro.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
There was no users left - so drop the code to support EARLY_EVENT_BLANK.
This patch removes the support in backlight,
and drop the notifier in fbmem.
That EARLY_EVENT_BLANK is not used can be verified that no driver set any of:
lcd_ops.early_set_power()
lcd_ops.r_early_set_power()
Noticed while browsing backlight code for other reasons.
v2:
- Fix changelog to say "EARLY_EVENT_BLANK" (Daniel)
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: "Michał Mirosław" <mirq-linux@rere.qmqm.pl>
Cc: Peter Rosin <peda@axentia.se>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-fbdev@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190725143224.GB31803@ravnborg.org
|
Suman Anna
Suthikulpanit, Suravee
Paolo Bonzini
Greg Kroah-Hartman
Suzuki K Poulose
Thiago Jung Bauermann
Neil Armstrong
Linus Walleij
Dave Airlie
Jakub Kicinski
Masahiro Yamada
Jose Abreu
Edward Cree
Rahul Verma
Paul Cercueil
Denis Efremov
Tariq Toukan
Rafael J. Wysocki
Narendra K
Ard Biesheuvel
Peter Zijlstra
Andrey Smirnov
Chuhong Yuan
Christoph Hellwig
Marc Zyngier
Leo Yan
Jianjun Wang
David S. Miller
Linus Torvalds
Stephen Rothwell
Hans Holmberg
Mukesh Ojha
Davidlohr Bueso
Bjorn Andersson
Sam Ravnborg