| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
For set/query MTU port firmware commands the MTU field
is 16 bits, here I changed all the "int mtu" parameters
of the functions wrapping those firmware commands to be u16.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently when filesystem needs to make sure data is on permanent
storage before committing a transaction it adds inode to transaction's
inode list. During transaction commit, jbd2 writes back all dirty
buffers that have allocated underlying blocks and waits for the IO to
finish. However when doing writeback for delayed allocated data, we
allocate blocks and immediately submit the data. Thus asking jbd2 to
write dirty pages just unnecessarily adds more work to jbd2 possibly
writing back other redirtied blocks.
Add support to jbd2 to allow filesystem to ask jbd2 to only wait for
outstanding data writes before committing a transaction and thus avoid
unnecessary writes.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for your net-next
tree, mostly from Florian Westphal to sort out the lack of sufficient
validation in x_tables and connlabel preparation patches to add
nf_tables support. They are:
1) Ensure we don't go over the ruleset blob boundaries in
mark_source_chains().
2) Validate that target jumps land on an existing xt_entry. This extra
sanitization comes with a performance penalty when loading the ruleset.
3) Introduce xt_check_entry_offsets() and use it from {arp,ip,ip6}tables.
4) Get rid of the smallish check_entry() functions in {arp,ip,ip6}tables.
5) Make sure the minimal possible target size in x_tables.
6) Similar to #3, add xt_compat_check_entry_offsets() for compat code.
7) Check that standard target size is valid.
8) More sanitization to ensure that the target_offset field is correct.
9) Add xt_check_entry_match() to validate that matches are well-formed.
10-12) Three patch to reduce the number of parameters in
translate_compat_table() for {arp,ip,ip6}tables by using a container
structure.
13) No need to return value from xt_compat_match_from_user(), so make
it void.
14) Consolidate translate_table() so it can be used by compat code too.
15) Remove obsolete check for compat code, so we keep consistent with
what was already removed in the native layout code (back in 2007).
16) Get rid of target jump validation from mark_source_chains(),
obsoleted by #2.
17) Introduce xt_copy_counters_from_user() to consolidate counter
copying, and use it from {arp,ip,ip6}tables.
18,22) Get rid of unnecessary explicit inlining in ctnetlink for dump
functions.
19) Move nf_connlabel_match() to xt_connlabel.
20) Skip event notification if connlabel did not change.
21) Update of nf_connlabels_get() to make the upcoming nft connlabel
support easier.
23) Remove spinlock to read protocol state field in conntrack.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull thermal fixes from Eduardo Valentin:
"Specifics in this pull request:
- Fixes in mediatek and OF thermal drivers
- Fixes in power_allocator governor
- More fixes of unsigned to int type change in thermal_core.c.
These change have been CI tested using KernelCI bot. \o/"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
thermal: fix Mediatek thermal controller build
thermal: consistently use int for trip temp
thermal: fix mtk_thermal build dependency
thermal: minor mtk_thermal.c cleanups
thermal: power_allocator: req_range multiplication should be a 64 bit type
thermal: of: add __init attribute
|
|
nla_data() is now aligned on a 64-bit area.
The temporary function nla_put_be64_32bit() is removed in this patch.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts were two cases of simple overlapping changes,
nothing serious.
In the UDP case, we need to add a hlist_add_tail_rcu()
to linux/rculist.h, because we've moved UDP socket handling
away from using nulls lists.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a new rotation matrix sysfs attribute compliant with IIO core
mounting matrix API.
Matrix is retrieved from "in_anglvel_mount_matrix" and
"in_accel_mount_matrix" sysfs attributes. It is declared into mpu6050 DTS
entry as a "mount-matrix" property.
Old interface is kept for backward userspace compatibility and may be
retrieved from legacy platform_data mechanism only.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Expose a rotation matrix to indicate userspace the chip orientation with
respect to the overall hardware system.
Matrix is retrieved from "in_mount_matrix". It is declared into ak8975 DTS
entry as a "mount-matrix" property.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Expose a rotation matrix to indicate userspace the chip placement with
respect to the overall hardware system. This is needed to adjust
coordinates sampled from a sensor chip when its position deviates from the
main hardware system.
Final coordinates computation is delegated to userspace since:
* computation may involve floating point arithmetics ;
* it allows an application to combine adjustments with arbitrary
transformations.
This 3 dimentional space rotation matrix is expressed as 3x3 array of
strings to support floating point numbers. It may be retrieved from a
"[<dir>_][<type>_]mount_matrix" sysfs attribute file. It is declared into a
device / driver specific DTS property or platform data.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Ticks can happen while the CPU is in dynticks-idle or dynticks-singletask
mode. In fact "nohz" or "dynticks" only mean that we exit the periodic
mode and we try to minimize the ticks as much as possible. The nohz
subsystem uses a confusing terminology with the internal state
"ts->tick_stopped" which is also available through its public interface
with tick_nohz_tick_stopped(). This is a misnomer as the tick is instead
reduced with the best effort rather than stopped. In the best case the
tick can indeed be actually stopped but there is no guarantee about that.
If a timer needs to fire one second later, a tick will fire while the
CPU is in nohz mode and this is a very common scenario.
Now this confusion happens to be a problem with CPU load updates:
cpu_load_update_active() doesn't handle nohz ticks correctly because it
assumes that ticks are completely stopped in nohz mode and that
cpu_load_update_active() can't be called in dynticks mode. When that
happens, the whole previous tickless load is ignored and the function
just records the load for the current tick, ignoring potentially long
idle periods behind.
In order to solve this, we could account the current load for the
previous nohz time but there is a risk that we account the load of a
task that got freshly enqueued for the whole nohz period.
So instead, lets record the dynticks load on nohz frame entry so we know
what to record in case of nohz ticks, then use this record to account
the tickless load on nohz ticks and nohz frame end.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Byungchul Park <byungchul.park@lge.com>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Luiz Capitulino <lcapitulino@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul E . McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1460555812-25375-3-git-send-email-fweisbec@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The CPU load update related functions have a weak naming convention
currently, starting with update_cpu_load_*() which isn't ideal as
"update" is a very generic concept.
Since two of these functions are public already (and a third is to come)
that's enough to introduce a more conventional naming scheme. So let's
do the following rename instead:
update_cpu_load_*() -> cpu_load_update_*()
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Byungchul Park <byungchul.park@lge.com>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Luiz Capitulino <lcapitulino@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul E . McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1460555812-25375-2-git-send-email-fweisbec@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This patch introduces 'write_backward' bit to perf_event_attr, which
controls the direction of a ring buffer. After set, the corresponding
ring buffer is written from end to beginning. This feature is design to
support reading from overwritable ring buffer.
Ring buffer can be created by mapping a perf event fd. Kernel puts event
records into ring buffer, user tooling like perf fetch them from
address returned by mmap(). To prevent racing between kernel and tooling,
they communicate to each other through 'head' and 'tail' pointers.
Kernel maintains 'head' pointer, points it to the next free area (tail
of the last record). Tooling maintains 'tail' pointer, points it to the
tail of last consumed record (record has already been fetched). Kernel
determines the available space in a ring buffer using these two
pointers to avoid overwrite unfetched records.
By mapping without 'PROT_WRITE', an overwritable ring buffer is created.
Different from normal ring buffer, tooling is unable to maintain 'tail'
pointer because writing is forbidden. Therefore, for this type of ring
buffers, kernel overwrite old records unconditionally, works like flight
recorder. This feature would be useful if reading from overwritable ring
buffer were as easy as reading from normal ring buffer. However,
there's an obscure problem.
The following figure demonstrates a full overwritable ring buffer. In
this figure, the 'head' pointer points to the end of last record, and a
long record 'E' is pending. For a normal ring buffer, a 'tail' pointer
would have pointed to position (X), so kernel knows there's no more
space in the ring buffer. However, for an overwritable ring buffer,
kernel ignore the 'tail' pointer.
(X) head
. |
. V
+------+-------+----------+------+---+
|A....A|B.....B|C........C|D....D| |
+------+-------+----------+------+---+
Record 'A' is overwritten by event 'E':
head
|
V
+--+---+-------+----------+------+---+
|.E|..A|B.....B|C........C|D....D|E..|
+--+---+-------+----------+------+---+
Now tooling decides to read from this ring buffer. However, none of these
two natural positions, 'head' and the start of this ring buffer, are
pointing to the head of a record. Even the full ring buffer can be
accessed by tooling, it is unable to find a position to start decoding.
The first attempt tries to solve this problem AFAIK can be found from
[1]. It makes kernel to maintain 'tail' pointer: updates it when ring
buffer is half full. However, this approach introduces overhead to
fast path. Test result shows a 1% overhead [2]. In addition, this method
utilizes no more tham 50% records.
Another attempt can be found from [3], which allows putting the size of
an event at the end of each record. This approach allows tooling to find
records in a backward manner from 'head' pointer by reading size of a
record from its tail. However, because of alignment requirement, it
needs 8 bytes to record the size of a record, which is a huge waste. Its
performance is also not good, because more data need to be written.
This approach also introduces some extra branch instructions to fast
path.
'write_backward' is a better solution to this problem.
Following figure demonstrates the state of the overwritable ring buffer
when 'write_backward' is set before overwriting:
head
|
V
+---+------+----------+-------+------+
| |D....D|C........C|B.....B|A....A|
+---+------+----------+-------+------+
and after overwriting:
head
|
V
+---+------+----------+-------+---+--+
|..E|D....D|C........C|B.....B|A..|E.|
+---+------+----------+-------+---+--+
In each situation, 'head' points to the beginning of the newest record.
From this record, tooling can iterate over the full ring buffer and fetch
records one by one.
The only limitation that needs to be considered is back-to-back reading.
Due to the non-deterministic of user programs, it is impossible to ensure
the ring buffer keeps stable during reading. Consider an extreme situation:
tooling is scheduled out after reading record 'D', then a burst of events
come, eat up the whole ring buffer (one or multiple rounds). When the
tooling process comes back, reading after 'D' is incorrect now.
To prevent this problem, we need to find a way to ensure the ring buffer
is stable during reading. ioctl(PERF_EVENT_IOC_PAUSE_OUTPUT) is
suggested because its overhead is lower than
ioctl(PERF_EVENT_IOC_ENABLE).
By carefully verifying 'header' pointer, reader can avoid pausing the
ring-buffer. For example:
/* A union of all possible events */
union perf_event event;
p = head = perf_mmap__read_head();
while (true) {
/* copy header of next event */
fetch(&event.header, p, sizeof(event.header));
/* read 'head' pointer */
head = perf_mmap__read_head();
/* check overwritten: is the header good? */
if (!verify(sizeof(event.header), p, head))
break;
/* copy the whole event */
fetch(&event, p, event.header.size);
/* read 'head' pointer again */
head = perf_mmap__read_head();
/* is the whole event good? */
if (!verify(event.header.size, p, head))
break;
p += event.header.size;
}
However, the overhead is high because:
a) In-place decoding is not safe.
Copying-verifying-decoding is required.
b) Fetching 'head' pointer requires additional synchronization.
(From Alexei Starovoitov:
Even when this trick works, pause is needed for more than stability of
reading. When we collect the events into overwrite buffer we're waiting
for some other trigger (like all cpu utilization spike or just one cpu
running and all others are idle) and when it happens the buffer has
valuable info from the past. At this point new events are no longer
interesting and buffer should be paused, events read and unpaused until
next trigger comes.)
This patch utilizes event's default overflow_handler introduced
previously. perf_event_output_backward() is created as the default
overflow handler for backward ring buffers. To avoid extra overhead to
fast path, original perf_event_output() becomes __perf_event_output()
and marked '__always_inline'. In theory, there's no extra overhead
introduced to fast path.
Performance testing:
Calling 3000000 times of 'close(-1)', use gettimeofday() to check
duration. Use 'perf record -o /dev/null -e raw_syscalls:*' to capture
system calls. In ns.
Testing environment:
CPU : Intel(R) Core(TM) i7-4790 CPU @ 3.60GHz
Kernel : v4.5.0
MEAN STDVAR
BASE 800214.950 2853.083
PRE1 2253846.700 9997.014
PRE2 2257495.540 8516.293
POST 2250896.100 8933.921
Where 'BASE' is pure performance without capturing. 'PRE1' is test
result of pure 'v4.5.0' kernel. 'PRE2' is test result before this
patch. 'POST' is test result after this patch. See [4] for the detailed
experimental setup.
Considering the stdvar, this patch doesn't introduce performance
overhead to the fast path.
[1] http://lkml.iu.edu/hypermail/linux/kernel/1304.1/04584.html
[2] http://lkml.iu.edu/hypermail/linux/kernel/1307.1/00535.html
[3] http://lkml.iu.edu/hypermail/linux/kernel/1512.0/01265.html
[4] http://lkml.kernel.org/g/56F89DCD.1040202@huawei.com
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Cc: <acme@kernel.org>
Cc: <pi3orama@163.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Brendan Gregg <brendan.d.gregg@gmail.com>
Cc: He Kuang <hekuang@huawei.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: Zefan Li <lizefan@huawei.com>
Link: http://lkml.kernel.org/r/1459865478-53413-1-git-send-email-wangnan0@huawei.com
[ Fixed the changelog some more. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
lock_chain::base is used to store an index into the chain_hlocks[]
array, however that array contains more elements than can be indexed
using the u16.
Change the lock_chain structure to use a bitfield to encode the data
it needs and add BUILD_BUG_ON() assertions to check the fields are
wide enough.
Also, for DEBUG_LOCKDEP, assert that we don't run out of elements of
that array; as that would wreck the collision detectoring.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alfredo Alvarez Fernandez <alfredoalvarezfernandez@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sedat Dilek <sedat.dilek@gmail.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20160330093659.GS3408@twins.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
In preparation for providing an alternative (to block device) access
mechanism to persistent memory, convert pmem_rw_bytes() to
nsio_rw_bytes(). This allows ->rw_bytes() functionality without
requiring a 'struct pmem_device' to be instantiated.
In other words, when ->rw_bytes() is in use i/o is driven through
'struct nd_namespace_io', otherwise it is driven through 'struct
pmem_device' and the block layer. This consolidates the disjoint calls
to devm_exit_badblocks() and devm_memunmap() into a common
devm_nsio_disable() and cleans up the init path to use a unified
pmem_attach_disk() implementation.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Consolidate the information for issuing i/o to a blk-namespace, and
eliminate some pointer chasing.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
The do_sys_settimeofday() function uses a timespec, which is not year
2038 safe on 32bit systems.
Thus this patch introduces do_sys_settimeofday64(), which allows us to
transition users of do_sys_settimeofday() to using 64bit time types.
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
[jstultz: Include errno-base.h to avoid build issue on some arches]
Signed-off-by: John Stultz <john.stultz@linaro.org>
|
|
security_settime() uses a timespec, which is not year 2038 safe
on 32bit systems. Thus this patch introduces the security_settime64()
function with timespec64 type. We also convert the cap_settime() helper
function to use the 64bit types.
This patch then moves security_settime() to the header file as an
inline helper function so that existing users can be iteratively
converted.
None of the existing hooks is using the timespec argument and therefor
the patch is not making any functional changes.
Cc: Serge Hallyn <serge.hallyn@canonical.com>,
Cc: James Morris <james.l.morris@oracle.com>,
Cc: "Serge E. Hallyn" <serge@hallyn.com>,
Cc: Paul Moore <pmoore@redhat.com>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: Kees Cook <keescook@chromium.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Reviewed-by: James Morris <james.l.morris@oracle.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
[jstultz: Reworded commit message]
Signed-off-by: John Stultz <john.stultz@linaro.org>
|
|
This header uses OF_DELCARE_1 which is defined in linux/of.h.
This fixes getting unhelpful compiler error messages about missing ')'
before a string constant.
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
|
|
All i2c mux users are using an explicit i2c mux core, drop support
for implicit i2c mux cores.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
All i2c-muxes have a parent adapter and one or many child
adapters. A mux also has some means of selection. Previously,
this was stored per child adapter, but it is only needed
to keep track of this per mux.
Add an i2c mux core, that keeps track of this consistently.
Also add some glue for users of the old interface, which will
create one implicit mux core per child adapter.
Signed-off-by: Peter Rosin <peda@axentia.se>
Tested-by: Antti Palosaari <crope@iki.fi>
Tested-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The open coded conversion from struct page address to virtual address in
lowmem_page_address() involves an intermediate conversion step to pfn
number/physical address. Since the placement of the struct page array
relative to the linear mapping may be completely independent from the
placement of physical RAM (as is that case for arm64 after commit
dfd55ad85e 'arm64: vmemmap: use virtual projection of linear region'),
the conversion to physical address and back again should factor out of
the equation, but unfortunately, the shifting and pointer arithmetic
involved prevent this from happening, and the resulting calculation
essentially subtracts the address of the start of physical memory and
adds it back again, in a way that prevents the compiler from optimizing
it away.
Since the start of physical memory is not a build time constant on arm64,
the resulting conversion involves an unnecessary memory access, which
we would like to get rid of. So replace the open coded conversion with
a call to page_to_virt(), and use the open coded conversion as its
default definition, to be overriden by the architecture, if desired.
The existing arch specific definitions of page_to_virt are all equivalent
to this default definition, so by itself this patch is a no-op.
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Since we are removing paravirt_enabled() replace it with a
logical equivalent. Even though PNPBIOS is x86 specific we
add an arch-specific type call, which can be implemented by
any architecture to show how other legacy attribute devices
can later be also checked for with other ACPI legacy attribute
flags.
This implicates the first ACPI 5.2.9.3 IA-PC Boot Architecture
ACPI_FADT_LEGACY_DEVICES flag device, and shows how to add more.
The reason pnpbios gets a defined structure and as such uses
a different approach than the RTC legacy quirk is that ACPI
has a respective RTC flag, while pnpbios does not. We fold
the pnpbios quirk under ACPI_FADT_LEGACY_DEVICES ACPI flag
use case, and use a struct of possible devices to enable
future extensions of this.
As per 0-day, this bumps the vmlinux size using i386-tinyconfig as
follows:
TOTAL TEXT init.text x86_early_init_platform_quirks()
+32 +28 +28 +28
That's 4 byte overhead total, the rest is cleared out on init
as its all __init text.
v2: split out subarch handlng on switch to make it easier
later to add other subarchs. The 'fall-through' switch
handling can be confusing and we'll remove it later
when we add handling for X86_SUBARCH_CE4100.
v3: document vmlinux size impact as per 0-day, and also
explain why pnpbios is treated differently than the
RTC legacy feature.
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: andrew.cooper3@citrix.com
Cc: andriy.shevchenko@linux.intel.com
Cc: bigeasy@linutronix.de
Cc: boris.ostrovsky@oracle.com
Cc: david.vrabel@citrix.com
Cc: ffainelli@freebox.fr
Cc: george.dunlap@citrix.com
Cc: glin@suse.com
Cc: jgross@suse.com
Cc: jlee@suse.com
Cc: josh@joshtriplett.org
Cc: julien.grall@linaro.org
Cc: konrad.wilk@oracle.com
Cc: kozerkov@parallels.com
Cc: lenb@kernel.org
Cc: lguest@lists.ozlabs.org
Cc: linux-acpi@vger.kernel.org
Cc: lv.zheng@intel.com
Cc: matt@codeblueprint.co.uk
Cc: mbizon@freebox.fr
Cc: rjw@rjwysocki.net
Cc: robert.moore@intel.com
Cc: rusty@rustcorp.com.au
Cc: tiwai@suse.de
Cc: toshi.kani@hp.com
Cc: xen-devel@lists.xensource.com
Link: http://lkml.kernel.org/r/1460592286-300-12-git-send-email-mcgrof@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
As of commit b12ff41658171f53 ("ARM: shmobile: r8a7779: Remove legacy PM
Domain remainings"), rcar_sysc_power_is_off() is no longer used from
SoC-specific code.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Move the pm-rcar driver from arch/arm/mach-shmobile/ to
drivers/soc/renesas/, and its header file to include/linux/soc/renesas/,
so it can be shared between arm32 (R-Car H1 and Gen2) and arm64 (R-Car
Gen3). Rename it to rcar-sysc as it's really a driver for the R-Car
System Controller (SYSC).
Kill the intermediate PM_RCAR config symbol, as it's not user
configurable anymore, and to prepare for SoC-specific make rules.
Add the missing #include <linux/types.h> to rcar-sysc.h, which was
exposed by different include order.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Now that all the architectures implement the necessary glue code
we can introduce down_write_killable(). The only difference wrt. regular
down_write() is that the slow path waits in TASK_KILLABLE state and the
interruption by the fatal signal is reported as -EINTR to the caller.
Signed-off-by: Michal Hocko <mhocko@suse.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Chris Zankel <chris@zankel.net>
Cc: David S. Miller <davem@davemloft.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Cc: Signed-off-by: Jason Low <jason.low2@hp.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-alpha@vger.kernel.org
Cc: linux-arch@vger.kernel.org
Cc: linux-ia64@vger.kernel.org
Cc: linux-s390@vger.kernel.org
Cc: linux-sh@vger.kernel.org
Cc: linux-xtensa@linux-xtensa.org
Cc: sparclinux@vger.kernel.org
Link: http://lkml.kernel.org/r/1460041951-22347-12-git-send-email-mhocko@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
As a part of the ongoing consolidation of genpd, it's become questionable
whether clients actually needs to be able to assign their own set of
->save|restore_state() callbacks. Currently all users copes fine with the
default callbacks, so let's remove the configuration option and stick to
the default ones.
This enables further clarifications of the related code and let's also
rename pm_genpd_default_save|restore_state() into
__genpd_runtime_suspend|resume() to apply the rule of static functionnames
in genpd.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The genpd governor validates the latency constraints to find out whether
it's acceptable to runtime suspend a device. Earlier this validation was
made to know whether it was okay to invoke the ->stop() callback for the
device, hence the governor used the name "stop_ok" for the related
variables.
To clarify the code around this, let's rename these variables from
"stop_ok" to "suspend_ok".
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The ignore_children flag is used only when CONFIG_PM is set, so let's move
it into that section within the struct dev_pm_info.
Move also the corresponding pm_suspend_ignore_children() API out of
device.h into pm_runtime.h, to be consistent with similar APIs.
Unfortunate this causes the Toshiba PCI SD mmc host driver to fail to
compile as it needs pm_runtime.h, so let's fix this here as well.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
- make modeset hw state checker atomic aware (Maarten)
- close races in gpu stuck detection/seqno reading (Chris)
- tons&tons of small improvements from Chris Wilson all over the gem code
- more dsi/bxt work from Ramalingam&Jani
- macro polish from Joonas
- guc fw loading fixes (Arun&Dave)
- vmap notifier (acked by Andrew) + i915 support by Chris Wilson
- create bottom half for execlist irq processing (Chris Wilson)
- vlv/chv pll cleanup (Ville)
- rework DP detection, especially sink detection (Shubhangi Shrivastava)
- make color manager support fully atomic (Maarten)
- avoid livelock on chv in execlist irq handler (Chris)
* tag 'drm-intel-next-2016-04-11' of git://anongit.freedesktop.org/drm-intel: (82 commits)
drm/i915: Update DRIVER_DATE to 20160411
drm/i915: Avoid allocating a vmap arena for a single page
drm,i915: Introduce drm_malloc_gfp()
drm/i915/shrinker: Restrict vmap purge to objects with vmaps
drm/i915: Refactor duplicate object vmap functions
drm/i915: Consolidate common error handling in intel_pin_and_map_ringbuffer_obj
drm/i915/dmabuf: Tighten struct_mutex for unmap_dma_buf
drm/i915: implement WaClearTdlStateAckDirtyBits
drm/i915/bxt: Reversed polarity of PORT_PLL_REF_SEL bit
drm/i915: Rename hw state checker to hw state verifier.
drm/i915: Move modeset state verifier calls.
drm/i915: Make modeset state verifier take crtc as argument.
drm/i915: Replace manual barrier() with READ_ONCE() in HWS accessor
drm/i915: Use simplest form for flushing the single cacheline in the HWS
drm/i915: Harden detection of missed interrupts
drm/i915: Separate out the seqno-barrier from engine->get_seqno
drm/i915: Remove forcewake dance from seqno/irq barrier on legacy gen6+
drm/i915: Fixup the free space logic in ring_prepare
drm/i915: Simplify check for idleness in hangcheck
drm/i915: Apply a mb between emitting the request and hangcheck
...
|
|
Backmerge 4.6-rc3 for i915.
Linux 4.6-rc3
|
|
* 'clk-hw-register' (early part):
clk: fixed-rate: Add hw based registration APIs
clk: gpio: Add hw based registration APIs
clk: composite: Add hw based registration APIs
clk: fractional-divider: Add hw based registration APIs
clk: fixed-factor: Add hw based registration APIs
clk: mux: Add hw based registration APIs
clk: gate: Add hw based registration APIs
clk: divider: Add hw based registration APIs
clkdev: Add clk_hw based registration APIs
clk: Add clk_hw OF clk providers
clk: Add {devm_}clk_hw_{register,unregister}() APIs
clkdev: Remove clk_register_clkdevs()
|
|
* clk-composite-unregister:
clk: composite: Add unregister function
|
|
The composite clock didn't have any unregistration function, which forced
us to use clk_unregister directly on it.
While it was already not great from an API point of view, it also meant
that we were leaking the clk_composite structure allocated in
clk_register_composite.
Add a clk_unregister_composite function to fix this.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
doc.2016.04.19a: Documentation updates
exp.2016.03.31d: Expedited grace-period updates
fixes.2016.03.31d: Miscellaneous fixes
torture.2016.004.21a Torture-test updates
|
|
Pull networking fixes from David Miller:
1) Fix memory leak in iwlwifi, from Matti Gottlieb.
2) Add missing registration of netfilter arp_tables into initial
namespace, from Florian Westphal.
3) Fix potential NULL deref in DecNET routing code.
4) Restrict NETLINK_URELEASE to truly bound sockets only, from Dmitry
Ivanov.
5) Fix dst ref counting in VRF, from David Ahern.
6) Fix TSO segmenting limits in i40e driver, from Alexander Duyck.
7) Fix heap leak in PACKET_DIAG_MCLIST, from Mathias Krause.
8) Ravalidate IPV6 datagram socket cached routes properly, particularly
with UDP, from Martin KaFai Lau.
9) Fix endian bug in RDS dp_ack_seq handling, from Qing Huang.
10) Fix stats typing in bcmgenet driver, from Eric Dumazet.
11) Openvswitch needs to orphan SKBs before ipv6 fragmentation handing,
from Joe Stringer.
12) SPI device reference leak in spi_ks8895 PHY driver, from Mark Brown.
13) atl2 doesn't actually support scatter-gather, so don't advertise the
feature. From Ben Hucthings.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (72 commits)
openvswitch: use flow protocol when recalculating ipv6 checksums
Driver: Vmxnet3: set CHECKSUM_UNNECESSARY for IPv6 packets
atl2: Disable unimplemented scatter/gather feature
net/mlx4_en: Split SW RX dropped counter per RX ring
net/mlx4_core: Don't allow to VF change global pause settings
net/mlx4_core: Avoid repeated calls to pci enable/disable
net/mlx4_core: Implement pci_resume callback
net: phy: spi_ks8895: Don't leak references to SPI devices
net: ethernet: davinci_emac: Fix platform_data overwrite
net: ethernet: davinci_emac: Fix Unbalanced pm_runtime_enable
qede: Fix single MTU sized packet from firmware GRO flow
qede: Fix setting Skb network header
qede: Fix various memory allocation error flows for fastpath
tcp: Merge tx_flags and tskey in tcp_shifted_skb
tcp: Merge tx_flags and tskey in tcp_collapse_retrans
drivers: net: cpsw: fix wrong regs access in cpsw_ndo_open
tcp: Fix SOF_TIMESTAMPING_TX_ACK when handling dup acks
openvswitch: Orphan skbs before IPv6 defrag
Revert "Prevent NUll pointer dereference with two PHYs on cpsw"
VSOCK: Only check error on skb_recv_datagram when skb is NULL
...
|
|
Equivalent to "vxlan: break dependency with netdev drivers", don't
autoload geneve module in case the driver is loaded. Instead make the
coupling weaker by using netdevice notifiers as proxy.
Cc: Jesse Gross <jesse@kernel.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently all drivers depend and autoload the vxlan module because how
vxlan_get_rx_port is linked into them. Remove this dependency:
By using a new event type in the netdevice notifier call chain we proxy
the request from the drivers to flush and resetup the vxlan ports not
directly via function call but by the already existing netdevice
notifier call chain.
I added a separate new event type, NETDEV_OFFLOAD_PUSH_VXLAN, to do so.
We don't need to save those ids, as the event type field is an unsigned
long and using specialized event types for this purpose seemed to be a
more elegant way. This also comes in beneficial if in future we want to
add offloading knobs for vxlan.
Cc: Jesse Gross <jesse@kernel.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce the feature of multi-packet WQE (RX Work Queue Element)
referred to as (MPWQE or Striding RQ), in which WQEs are larger
and serve multiple packets each.
Every WQE consists of many strides of the same size, every received
packet is aligned to a beginning of a stride and is written to
consecutive strides within a WQE.
In the regular approach, each regular WQE is big enough to be capable
of serving one received packet of any size up to MTU or 64K in case of
device LRO is enabled, making it very wasteful when dealing with
small packets or device LRO is enabled.
For its flexibility, MPWQE allows a better memory utilization
(implying improvements in CPU utilization and packet rate) as packets
consume strides according to their size, preserving the rest of
the WQE to be available for other packets.
MPWQE default configuration:
Num of WQEs = 16
Strides Per WQE = 2048
Stride Size = 64 byte
The default WQEs memory footprint went from 1024*mtu (~1.5MB) to
16 * 2048 * 64 = 2MB per ring.
However, HW LRO can now be supported at no additional cost in memory
footprint, and hence we turn it on by default and get an even better
performance.
Performance tested on ConnectX4-Lx 50G.
To isolate the feature under test, the numbers below were measured with
HW LRO turned off. We verified that the performance just improves when
LRO is turned back on.
* Netperf single TCP stream:
- BW raised by 10-15% for representative packet sizes:
default, 64B, 1024B, 1478B, 65536B.
* Netperf multi TCP stream:
- No degradation, line rate reached.
* Pktgen: packet rate raised by 2-10% for traffic of different message
sizes: 64B, 128B, 256B, 1024B, and 1500B.
* Pktgen: packet loss in bursts of small messages (64byte),
single stream:
- | num packets | packets loss before | packets loss after
| 2K | ~ 1K | 0
| 8K | ~ 6K | 0
| 16K | ~13K | 0
| 32K | ~28K | 0
| 64K | ~57K | ~24K
As expected as the driver can receive as many small packets (<=64B) as
the number of total strides in the ring (default = 2048 * 16) vs. 1024
(default ring size regardless of packets size) before this feature.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A queue counter can collect several statistics for one or more
hardware queues (QPs, RQs, etc ..) that the counter is attached to.
For Ethernet it will provide an "out of buffer" counter which
collects the number of all packets that are dropped due to lack
of software buffers.
Here we add device commands to alloc/query/dealloc queue counters.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Rana Shahout <ranas@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Maintain the PCI status and provide wrappers for enabling and disabling
the PCI device. Performing the actions more than once without doing
its opposite results in warning logs.
This occurred when EEH hotplugged the device causing a warning for
disabling an already disabled device.
Fixes: 2ba5fbd62b25 ('net/mlx4_core: Handle AER flow properly')
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch folds NETIF_F_ALL_TSO into the bitmask for NETIF_F_GSO_SOFTWARE.
The idea is to avoid duplication of defines since the only difference
between the two was the GSO_UDP bit.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
move trace_call_bpf() into helper function to minimize the size
of perf_trace_*() tracepoint handlers.
text data bss dec hex filename
10541679 5526646 2945024 19013349 1221ee5 vmlinux_before
10509422 5526646 2945024 18981092 121a0e4 vmlinux_after
It may seem that perf_fetch_caller_regs() can also be moved,
but that is incorrect, since ip/sp will be wrong.
bpf+tracepoint performance is not affected, since
perf_swevent_put_recursion_context() is now inlined.
export_symbol_gpl can also be dropped.
No measurable change in normal perf tracepoints.
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit 17e8351a7739 consistently use int for temperature,
however it missed a few in trip temperature and thermal_core.
In current codes, the trip->temperature used "unsigned long"
and zone->temperature used"int", if the temperature is negative
value, it will get wrong result when compare temperature with
trip temperature.
This patch can fix it.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
This LSM enforces that kernel-loaded files (modules, firmware, etc)
must all come from the same filesystem, with the expectation that
such a filesystem is backed by a read-only device such as dm-verity
or CDROM. This allows systems that have a verified and/or unchangeable
filesystem to enforce module and firmware loading restrictions without
needing to sign the files individually.
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
|
|
A string representation of the kernel_read_file_id enumeration is
needed for displaying messages (eg. pr_info, auditing) that can be
used by multiple LSMs and the integrity subsystem. To simplify
keeping the list of strings up to date with the enumeration, this
patch defines two new preprocessing macros named __fid_enumify and
__fid_stringify to create the enumeration and an array of strings.
kernel_read_file_id_str() returns a string based on the enumeration.
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
[kees: removed removal of my old version, constified pointer values]
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: James Morris <james.l.morris@oracle.com>
|
|
Allocate a NULL-terminated file path with special characters escaped,
safe for logging.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: James Morris <james.l.morris@oracle.com>
|
|
Provide an escaped (but readable: no inter-argument NULLs) commandline
safe for logging.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: James Morris <james.l.morris@oracle.com>
|
|
Handle allocating and escaping a string safe for logging.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: James Morris <james.l.morris@oracle.com>
|
Saeed Mahameed
Jan Kara
David S. Miller
Linus Torvalds
Nicolas Dichtel
Gregor Boirie
Frederic Weisbecker
Ingo Molnar
Wang Nan
Peter Zijlstra
Dan Williams
Baolin Wang
David Lechner
Peter Rosin
Ard Biesheuvel
Luis R. Rodriguez
Geert Uytterhoeven
Michal Hocko
Ulf Hansson
Dave Airlie
Stephen Boyd
Maxime Ripard
Paul E. McKenney
Hannes Frederic Sowa
Tariq Toukan
Daniel Jurgens
Alexander Duyck
Alexei Starovoitov
Wei Ni
Kees Cook
Mimi Zohar