Age | Commit message (Collapse) | Author | Files | Lines |
|
This patch adds a new action - 'check_pkt_len' which checks the
packet length and executes a set of actions if the packet
length is greater than the specified length or executes
another set of actions if the packet length is lesser or equal to.
This action takes below nlattrs
* OVS_CHECK_PKT_LEN_ATTR_PKT_LEN - 'pkt_len' to check for
* OVS_CHECK_PKT_LEN_ATTR_ACTIONS_IF_GREATER - Nested actions
to apply if the packet length is greater than the specified 'pkt_len'
* OVS_CHECK_PKT_LEN_ATTR_ACTIONS_IF_LESS_EQUAL - Nested
actions to apply if the packet length is lesser or equal to the
specified 'pkt_len'.
The main use case for adding this action is to solve the packet
drops because of MTU mismatch in OVN virtual networking solution.
When a VM (which belongs to a logical switch of OVN) sends a packet
destined to go via the gateway router and if the nic which provides
external connectivity, has a lesser MTU, OVS drops the packet
if the packet length is greater than this MTU.
With the help of this action, OVN will check the packet length
and if it is greater than the MTU size, it will generate an
ICMP packet (type 3, code 4) and includes the next hop mtu in it
so that the sender can fragment the packets.
Reported-at:
https://mail.openvswitch.org/pipermail/ovs-discuss/2018-July/047039.html
Suggested-by: Ben Pfaff <blp@ovn.org>
Signed-off-by: Numan Siddique <nusiddiq@redhat.com>
CC: Gregory Rose <gvrose8192@gmail.com>
CC: Pravin B Shelar <pshelar@ovn.org>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Tested-by: Greg Rose <gvrose8192@gmail.com>
Reviewed-by: Greg Rose <gvrose8192@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1000BaseT standard requires that a link is reported as down earliest
after 750ms. Several use case however require a much faster detecion
of a broken link. Fast Link Down supports this by intentionally
violating a the standard. This patch exposes the Fast Link Down
feature of 88E1540 and 88E6390. These PHY's can be found as internal
PHY's in several switches: 88E6352, 88E6240, 88E6176, 88E6172,
and 88E6390(X). Fast Link Down and EEE are mutually exclusive.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds support for Fast Link Down as new PHY tunable.
Fast Link Down reduces the time until a link down event is reported
for 1000BaseT. According to the standard it's 750ms what is too long
for several use cases.
v2:
- add comment describing the constants
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of declaring a function in a .c file, declare it in a header
file and include that header file from the source files that define
and that use the function. That allows the compiler to verify
consistency of declaration and definition. See also commit
52267790ef52 ("sock: add MSG_ZEROCOPY") # v4.14.
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch avoids that the following warnings are reported when building
with W=1:
net/core/rtnetlink.c:3580: warning: Function parameter or member 'ndm' not described in 'ndo_dflt_fdb_add'
net/core/rtnetlink.c:3580: warning: Function parameter or member 'tb' not described in 'ndo_dflt_fdb_add'
net/core/rtnetlink.c:3580: warning: Function parameter or member 'dev' not described in 'ndo_dflt_fdb_add'
net/core/rtnetlink.c:3580: warning: Function parameter or member 'addr' not described in 'ndo_dflt_fdb_add'
net/core/rtnetlink.c:3580: warning: Function parameter or member 'vid' not described in 'ndo_dflt_fdb_add'
net/core/rtnetlink.c:3580: warning: Function parameter or member 'flags' not described in 'ndo_dflt_fdb_add'
net/core/rtnetlink.c:3718: warning: Function parameter or member 'ndm' not described in 'ndo_dflt_fdb_del'
net/core/rtnetlink.c:3718: warning: Function parameter or member 'tb' not described in 'ndo_dflt_fdb_del'
net/core/rtnetlink.c:3718: warning: Function parameter or member 'dev' not described in 'ndo_dflt_fdb_del'
net/core/rtnetlink.c:3718: warning: Function parameter or member 'addr' not described in 'ndo_dflt_fdb_del'
net/core/rtnetlink.c:3718: warning: Function parameter or member 'vid' not described in 'ndo_dflt_fdb_del'
net/core/rtnetlink.c:3861: warning: Function parameter or member 'skb' not described in 'ndo_dflt_fdb_dump'
net/core/rtnetlink.c:3861: warning: Function parameter or member 'cb' not described in 'ndo_dflt_fdb_dump'
net/core/rtnetlink.c:3861: warning: Function parameter or member 'filter_dev' not described in 'ndo_dflt_fdb_dump'
net/core/rtnetlink.c:3861: warning: Function parameter or member 'idx' not described in 'ndo_dflt_fdb_dump'
net/core/rtnetlink.c:3861: warning: Excess function parameter 'nlh' description in 'ndo_dflt_fdb_dump'
Cc: Hubert Sokolowski <hubert.sokolowski@intel.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch avoids that the following warning is reported when building
with W=1:
warning: Function parameter or member 'flags' not described in '__skb_flow_dissect'
Cc: Tom Herbert <tom@herbertland.com>
Fixes: cd79a2382aa5 ("flow_dissector: Add flags argument to skb_flow_dissector functions") # v4.3.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch avoids that the following warnings are reported when building
with W=1:
net/core/dev_ioctl.c:378: warning: Function parameter or member 'ifr' not described in 'dev_ioctl'
net/core/dev_ioctl.c:378: warning: Function parameter or member 'need_copyout' not described in 'dev_ioctl'
net/core/dev_ioctl.c:378: warning: Excess function parameter 'arg' description in 'dev_ioctl'
Cc: Al Viro <viro@zeniv.linux.org.uk>
Fixes: 44c02a2c3dc5 ("dev_ioctl(): move copyin/copyout to callers") # v4.16.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch avoids that the following warning is reported when building
with W=1:
warning: Function parameter or member 'bind_inany' not described in 'reuseport_add_sock'
Cc: Martin KaFai Lau <kafai@fb.com>
Fixes: 2dbb9b9e6df6 ("bpf: Introduce BPF_PROG_TYPE_SK_REUSEPORT") # v4.19.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This partially reverts ed8fe20205ac ("net: dsa: mv88e6xxx: prevent
interrupt storm caused by mv88e6390x_port_set_cmode"). I missed
that chip->ports[].cmode is overwritten anyway by the cmode
caching in mv88e6xxx_setup().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 8fcf0ec44c11f "bnx2x: Add FW 7.13.11.0" added said .bin FW to
linux-firmware; This patch incorporates the FW in the bnx2x driver.
This introduces few FW fixes and the support for Tx VLAN filtering.
Please consider applying it to 'net-next' tree.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
An FoU socket is currently bound to the wildcard-address. While this
works fine, there are several use-cases where the use of the
wildcard-address is not desirable. For example, I use FoU on some
multi-homed servers and would like to use FoU on only one of the
interfaces.
This commit adds support for binding FoU sockets to a given source
address/interface, as well as connecting the socket to a given
destination address/port. udp_tunnel already provides the required
infrastructure, so most of the code added is for exposing and setting
the different attributes (local address, peer address, etc.).
The lookups performed when we add, delete or get an FoU-socket has also
been updated to compare all the attributes a user can set. Since the
comparison now involves several elements, I have added a separate
comparison-function instead of open-coding.
In order to test the code and ensure that the new comparison code works
correctly, I started by creating a wildcard socket bound to port 1234 on
my machine. I then tried to create a non-wildcarded socket bound to the
same port, as well as fetching and deleting the socket (including source
address, peer address or interface index in the netlink request). Both
the create, fetch and delete request failed. Deleting/fetching the
socket was only successful when my netlink request attributes matched
those used to create the socket.
I then repeated the tests, but with a socket bound to a local ip
address, a socket bound to a local address + interface, and a bound
socket that was also «connected» to a peer. Add only worked when no
socket with the matching source address/interface (or wildcard) existed,
while fetch/delete was only successful when all attributes matched.
In addition to testing that the new code work, I also checked that the
current behavior is kept. If none of the new attributes are provided,
then an FoU-socket is configured as before (i.e., wildcarded). If any
of the new attributes are provided, the FoU-socket is configured as
expected.
v1->v2:
* Fixed building with IPv6 disabled (kbuild).
* Fixed a return type warning and make the ugly comparison function more
readable (kbuild).
* Describe more in detail what has been tested (thanks David Miller).
* Make peer port required if peer address is specified.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The C2 classification engine has a 256 entry TCAM, used for ternary
matches on an 8 byte Header Extracted Key. For now, we compute the
various indices for classification and RSS that use this engine thanks
to a set of macros.
This commit mainly renames the macros used to make it clear that they
should be used with the C2 engine, but also make use of the full 256
entries in the engine. For now, the C2 entries are only used for RSS.
These entries are put at the end of the TCAM range, in case we want to
add higher priority matches later on.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When classifying a packet pertaining to a given flow, the classifier
will issue multiple lookup commands until it finds one with the 'last'
bit set. It expects all prorities to be assign continuously (although
not necessarily in an ordered fashion) from 0 to the number of lookups.
We can initialize this once, and make sure unused lookups are given an
empty port map. This avoids having to maintain priorities and the
information of which lookup is the last.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
C2 TCAM entries can be invalidated to avoid unwanted matches. Make sure
all entries are invalidated at init, then validate only the ones we use.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Flow Table dictates what lookups will be issued for each flow type.
The lookup sequence for each flow is similar, and the index of each
lookup is computed by some macros.
There are similar mechanisms for the C2 TCAM lookups, so in order to
avoid confusion, rename the flow table index computing macros with a
common prefix.
The only difference in behaviour is that we now use the very first entry
in the flow for the RSS lookup (the first entry was previously unused).
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The classifier allows to combine multiple lookups in one "sequence" that
is counted as a single lookup to an engine, with a single result.
We don't actually use that feature, so remove any places where we set
this field, so that the classifier doesn't try to interpret these
fields.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This commit renames some of the classifier functions to follow the
naming 'mvpp2_port_*' that's used for function that act on a given port.
This commit is purely cosmetic.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move C2 read/write helpers higher in the file to ease future work that
rely on these helpers
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When writing a C2 entry to hardware, some registers writes will only
take effect when the TCAM_DATA4 register is written. This includes all
C2 TCAM registers, and the C2 invalidate register.
To make sure we always write C2 entries correctly, document that
behaviour with a comment, and move TCAM writes to the end of the
mvpp2_cls_c2_write helper.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The cls_table is a global read-only table containing the different
parameters that are used by various tables in the classifier. It
describes the links between the Header Parser, the decoding table and
the flow_table.
There are several possible way we want to iterate over that table,
depending on wich classifier engine we want to configure. For the Header
Parser, we want to iterate over each entry. For the Decoding table, we
want to iterate over each entry having a unique flow_id. Finally, when
configuring an ethtool flow, we want to iterate over each entry having a
unique flow_id and that has a given flow_type.
This commit introduces some iterator to both provide syntactic sugar and
also clarify the way we want to iterate over the table.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PPv2's Classifier uses multiple engines to perform classification. So
far, only the C2 engine is used, which has a 256 entries TCAM.
So far, we only accessed the relevant entries from the C2 engines, which
are the one implementing RSS. To implement and debug ntuple
classification offload, beaing able to see the hit count for each C2
entry is helpful, so this commit moves the logic to a dedicated
directory allowing to access each entry.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Classifier flow table is the central part of the PPv2 Classifier,
since it describes all classification steps performed for each flow.
It has 512 entries, shared between all ports, which are divided into
sequences that are pointed-to by the decoding table. Being able to see
which entries in the flow table were hit is a key point when
implementing and debugging classification offload.
This commit allows reading each flow table entry's hit count
independently, with a clear-on-read behaviour.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current way to store the required private data needed to access
various debugfs entries is to alloc them on the fly, share them within
the entries that need to access them, and finally have one entry free
that data upon closing. This leads to hard to maintain code, and is very
error-prone.
This commit stores all debugfs related data in the same place, making
sure this is allocated only when the debugfs directory is successfully
created, so that we don't waste memory when we don't use this feature.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The cls_flow table represent the overall configuration of the
classifier, used to match the different traffic classes in the Parsing
and Classification engines.
This configuration is static, and applies to all PPv2 instances, we must
therefore keep it const so that no modifications of this table are
performed at runtime.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The macro definition MVPP2_N_FLOWS is ambiguous because it really
represents the number of entries in the Header Parser that are used to
identify the classification flows.
Rename the macro to clearly state that we represent the number of flows
in the Header Parser.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The PPv2 classifier allows to perform multiple lookups on the same
engine when classifying a packet. These lookups can match similar parts
of a packet header, but perform different actions upon matching. To
differentiate these types of lookups, it's possible to specify a Lookup
Type in the flow table entries, which will be part of the key for the
lookup engines.
This commit introduces the use of Lookup Types for C2 matches. Since for
now we only perform C2 lookups to enable RSS, we only need one Lookup
Type.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Classifier flow table has 512 entries, that contains lookups
commands executed consecutively for every flow. Since we have 21
different flows, we have to carefully manage the flow table use.
As of today, the start index of a lookup sequence is computed
directly based in the flow->id. There are 8 reserved flow ids, from
0-7, which don't have any corresponding sequence in the flow table. We
can therefore ignore them when computing the index, and make so that the
first non-reserved flow point to the very beginning of the flow table.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Suggested-by: Alan Winkowski <walan@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PPv2's classifier supports extracting the MAC Destination Address from the
L2 header to perform RSS and flow steering. Add the missing case when
setting the Header Extracted Key fields in the flow table.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
int is not long enough to store all netdev_features, use the correct
dedicated type to store them when building the list of dev->features.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some enums in ice_tx_desc_cmd_bits have a trailing /* 2 BITS */ comment,
but the value has just one bit set (ex. ICE_TX_DESC_CMD_L4T_EOFT_SCTP
has the value 0x200 (i.e. only bit 9 is set). This is confusing and
misleading. So remove the comment.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Since the driver now hard codes the ITR granularity to 2 us in the
GLINT_CTL register the comment next to ITR_GRAN_S needs to be updated.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Remove some redundant text in the function header for __ice_vsi_get_qs
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Single statement if conditions don't need braces. Remove it.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Commit 37bb83901286 ("ice: Move common functions out of ice_main.c part
7/7") seems to have inadvertently introduced a function prototype for
ice_vsi_cfg_tc without a corresponding function implementation. Remove it.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Currently we aren't checking for the ICE_FC_NONE case for the current
flow control mode. This is causing "Unknown" to be printed for the
current flow control method if flow control is disabled. Fix this by
adding the case for ICE_FC_NONE to print "None".
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Currently the ice_q_vector structure and ice_ring_container structure
are taking up more space than necessary due to cache alignment holes
and unnecessary variables respectively. This is not helping the
driver's performance. The following fixes were done to improve cache
alignment, reduce wasted space, and increase performance.
1. Remove the ice_latency_range enum as it is unused.
2. Remove the latency_range variable in the ice_ring_container structure.
3. Change the size of the itr_idx in the ice_ring_container structure
from an int to an u16. This reduced the size of ice_ring_container
structure to 32 Bytes so it has no holes or padding.
4. Re-arrange the ice_q_vector structure using pahole to align
members as best as possible in regards to 64 Byte cache line size.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
If filter already exists, do not go through error path flow but instead
continue to process rest of the function. Hence have an appropriate check
after adding MAC filters.
Signed-off-by: Preethi Banala <preethi.banala@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch fixes issue that occurs when VF is attempting to remove
default LAN/MAC address, which is programmed by the administrator.
We shouldn't return error for the call by the VF, but continue with
the remaining steps to handle MAC opcode. Also update the dev_err
message to explicitly say that VF can't change MAC programmed by PF.
Also change "mac" to "MAC" for kernel print statements in the same file.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The VPINT_MBX_CTL register array must be programmed to enable VF admin
queue interrupts. Without this, VFs never get interrupts on vector 0,
and some VF drivers will fail to init.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
commit 63f545ed1285 ("ice: Add support for adaptive interrupt moderation")
was meant to add support for adaptive interrupt moderation but there was
an error on my part while formatting the patch, and thus only part of the
patch ended up being submitted.
This patch rectifies the error by adding the rest of the code.
Fixes: 63f545ed1285 ("ice: Add support for adaptive interrupt moderation")
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch implements the following pci_error_handler ops:
.error_detected = ice_pci_err_detected
.slot_reset = ice_pci_err_slot_reset
.reset_notify = ice_pci_err_reset_notify
.reset_prepare = ice_pci_err_reset_prepare
.reset_done = ice_pci_err_reset_done
.resume = ice_pci_err_resume
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Currently we check if the __ICE_PREPARED_FOR_RESET bit is set prior to
calling ice_prepare_for_reset in ice_reset_subtask(), but we aren't
checking that bit in ice_do_reset() before calling
ice_prepare_for_reset(). This is not consistent and can cause issues if
ice_prepare_for_reset() is called prior to ice_do_reset(). Fix this by
checking if the __ICE_PREPARED_FOR_RESET bit is set internal to
ice_prepare_for_reset().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When communicating with the AVF driver, we need to use the status codes
from virtchnl.h, not our own ice-specific codes. Without this, when an
error occurs, the VF will report nonsensical results.
NOTE: this depends on changes made to include/linux/avf/virtchnl.h by
commit bb58fd7eeffc ("i40e: Update status codes")
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Two log messages contained newlines in the middle of the message. This
resulted in unexpected driver log output.
This patch removes the newlines to restore consistency with the rest of
the driver log messages.
Signed-off-by: Jeremiah Kyle <jeremiah.kyle@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When the conntrack is initialized, there is no helper attached
yet so the nat info initialization (nf_nat_setup_info) skips
adding the seqadj ext.
A helper is attached later when the conntrack is not confirmed
but is going to be committed. In this case, if NAT is needed then
adds the seqadj ext as well.
Fixes: 16ec3d4fbb96 ("openvswitch: Fix cached ct with helper.")
Signed-off-by: Flavio Leitner <fbl@sysclose.org>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When running stacktrace_build_id_nmi, try to query
kernel.perf_event_max_sample_rate sysctl and use it as a sample_freq.
If there was an error reading sysctl, fallback to 5000.
kernel.perf_event_max_sample_rate sysctl can drift and/or can be
adjusted by the perf tool, so assuming a fixed number might be
problematic on a long running machine.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Take advantage of the software Rx batching by using
netif_receive_skb_list instead of napi_gro_receive.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the return value check which testing the wrong variable
in tipc_mcast_send_sync().
Fixes: c55c8edafa91 ("tipc: smooth change between replicast and broadcast")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The AQCS109 supports a proprietary 2-pair 1Gbps mode. The standard
registers don't allow to tell between 1000BaseT and 1000BaseT2.
Add reporting this proprietary mode based on a vendor register.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add reporting firmware details. These details are available only once
the firmware has finished initializing the chip. This can take some
time and we need to poll for init completion.
v2:
- Propagate timeout in aqr107_wait_reset_complete(). Don't bail out
completely on timeout because chip may be functional even w/o
firmware image.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|