| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Move some s_flags defines out of rdmavt and into hfi1 because they are
hfi1 specific and therefore should remain in the driver instead of
bubbling up to rdmavt.
Document device specific ranges in rdmavt and remap
those in hfi1.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Moving receive-side WQE allocation logic into rdmavt will allow
further code reuse between qib and hfi1 drivers.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Brian Welty <brian.welty@intel.com>
Signed-off-by: Harish Chegondi <harish.chegondi@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The s_ahgpsn was incorrectly placed in the read-mostly section of the QP
and the s_curr_size and s_hdrwords are oversized. The misplaced
s_ahgpsn will cause the read-mostly cachelines to thrash.
Place s_ahgpsn in the send side cache lines and correctly size and
s_hdrwords and s_cur_size to keep the send side cachelines at the same
size.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
A destroy of an MR prior to destroying the QP can cause the following
diagnostic if the QP is referencing the MR being de-registered:
hfi1 0000:05:00.0: hfi1_0: rvt_dereg_mr timeout mr ffff8808562108
00 pd ffff880859b20b00
The solution is to when the a non-zero refcount is encountered when
the MR is destroyed the QPs needs to be iterated looking for QPs in
the same PD as the MR. If rvt_qp_mr_clean() detects any such QP
references the rkey/lkey, the QP needs to be put into an error state
via a call to rvt_qp_error() which will trigger the clean up of any
stuck references.
This solution is as specified in IBTA 1.3 Volume 1 11.2.10.5.
[This is reproduced with the 0.4.9 version of qperf and the rc_bw test]
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
There are currently 3 spots in the qib and hfi1 driver that have
knowledge of the internal QP hash list that should only be in
scope to rdmavt QP code.
Add an iterator API for processing all QPs to hide the
nature of the RCU hashlist.
The API consists of:
- rvt_qp_iter_init()
* For iterating QPs one at a time for seq_file semantics
- rvt_qp_iter_next()
* For iterating QPs one at a time for seq_file semantics
- rvt_qp_iter()
* For iterating all QPs
The first two are used for things like seq_file prints.
The last is for code that just needs to iterate all QPs
in the system.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The pmtu field doens't have be stored in the QP structure
as it can easily be calculated when needed.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
|
|
Current computation of qp->timeout_jiffies in rvt_modify_qp() will cause
overflow due to the fact that the input to the function usecs_to_jiffies
is only 32-bit ( unsigned int). Overflow will occur when attr->timeout is
equal to or greater than 30. The consequence is unnecessarily excessive
retry and thus degradation of the system performance.
This patch fixes the problem by limiting the input to 5-bit and calling
usecs_to_jiffies() before multiplying the scaling factor.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Improve code readablity by adding inline functions
to read specific BTH/IB fields without knowledge of
byte offsets.
Reviewed-by: Brian Welty <brian.welty@intel.com>
Reviewed-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Don Hiatt <don.hiatt@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
This field is causing excessive cache line bouncing.
There are spare bytes in the r_lock cache line so the best approach
is to make an rvt QP field and remove from the hfi1 priv field.
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
This patch simply renames struct ib_ah_attr to
rdma_ah_attr as these fields specify attributes that are
not necessarily specific to IB.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Don Hiatt <don.hiatt@intel.com>
Reviewed-by: Niranjana Vishwanathapura <niranjana.vishwanathapura@intel.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The Infiniband spec defines "A multicast address is defined by a
MGID and a MLID" (section 10.5).
The current code only uses the MGID for identifying multicast groups.
Update the driver to be compliant with this definition.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The wqe should be read only and in fact the superfluous reset of the
RVT_SEND_RESERVE_USED flag causes an issue where reserved operations
elicit a bad completion to the ULP.
The maintenance of the flag is now entirely within rvt_post_one_wr()
where a reserved operation will set the flag and a non-reserved operation
will insure the operation that is about to be posted has the flag reset.
Fixes: Commit 856cc4c237ad ("IB/hfi1: Add the capability for reserved operations")
Reviewed-by: Don Hiatt <don.hiatt@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The work to create a completion helper moved the translation of send
wqe operations to completion opcodes to rdmvat.
This precludes having driver dependent operations. Make the translation
driver dependent by doing the translation in the driver prior to the
rvt_qp_swqe_complete() call using restored translation tables.
Fixes: Commit f2dc9cdce83c ("IB/rdmavt: Add a send completion helper")
Fixes: Commit 0771da5a6e9d ("IB/hfi1,IB/qib: Use new send completion helper")
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Rename RVT AETH defines and export in rdma/ib_hdrs.h
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Don Hiatt <don.hiatt@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Return usec from an index into ib_rvt_rnr_table.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Don Hiatt <don.hiatt@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The send complete for RC QPs mismanages the ack count when the
responder side is only in RTR.
A QP in that state cannot send requests, but it can be the target
for operations that elicit responses.
Adjust the RC completion logic to correct the count maintenance
by reflecting RECV_OK in a new state test.
Reviewed-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Convert copy_sge and related SGE state functions to use boolean.
For determining if QP is in user mode, add helper function in rdmavt_qp.h.
This is used to determine if QP needs the last byte ordering.
While here, change rvt_pd.user to a boolean.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Brian Welty <brian.welty@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
To move common code across target to rdmavt for code reuse.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Brian Welty <brian.welty@intel.com>
Signed-off-by: Venkata Sandeep Dhanalakota <venkata.s.dhanalakota@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Add rvt_compute_aeth() and rvt_get_credit() as shared functions in
rdmavt, moved from hfi1/qib logic.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Brian Welty <brian.welty@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Add rvt_rc_error() and rvt_comm_est() as shared functions in
rdmavt, moved from hfi1/qib logic.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Brian Welty <brian.welty@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Add rvt_div_round_up_mtu() and rvt_div_mtu() routines to
do the computation based on the pmtu and the log_pmtu.
Change divides in qib, hfi1 to use the new inlines.
Reviewed-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Add a helper to release mr references held by
an swqe.
Reviewed-by: Brian Welty <brian.welty@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
This is for use by client drivers to drive
send completions into a CQ.
A new exported table allows for the mapping
of ib_wr_opcode into a ib_wc_opcode.
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
This centralizes the function and improves code readability.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The use of the specific opcode test is redundant since
all ack entry users correctly manipulate the mr pointer
to selectively trigger the reference clearing.
The overly specific test hinders the use of implementation
specific operations.
The change needs to get rid of the union to insure that
an atomic value is not seen as an MR pointer.
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Hanging has been observed while writing a file over NFSoRDMA. Dmesg on
the server contains messages like these:
[ 931.992501] svcrdma: Error -22 posting RDMA_READ
[ 952.076879] svcrdma: Error -22 posting RDMA_READ
[ 982.154127] svcrdma: Error -22 posting RDMA_READ
[ 1012.235884] svcrdma: Error -22 posting RDMA_READ
[ 1042.319194] svcrdma: Error -22 posting RDMA_READ
Here is why:
With the base memory management extension enabled, FRMR is used instead
of FMR. The xprtrdma server issues each RDMA read request as the following
bundle:
(1)IB_WR_REG_MR, signaled;
(2)IB_WR_RDMA_READ, signaled;
(3)IB_WR_LOCAL_INV, signaled & fencing.
These requests are signaled. In order to generate completion, the fast
register work request is processed by the hfi1 send engine after being
posted to the work queue, and the corresponding lkey is not valid until
the request is processed. However, the rdmavt driver validates lkey when
the RDMA read request is posted and thus it fails immediately with error
-EINVAL (-22).
This patch changes the work flow of local operations (fast register and
local invalidate) so that fast register work requests are always
processed immediately to ensure that the corresponding lkey is valid
when subsequent work requests are posted. Local invalidate requests are
processed immediately if fencing is not required and no previous local
invalidate request is pending.
To allow completion generation for signaled local operations that have
been processed before posting to the work queue, an internal send flag
RVT_SEND_COMPLETION_ONLY is added. The hfi1 send engine checks this flag
and only generates completion for such requests.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Jianxin Xiong <jianxin.xiong@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
This fix allows for support of in-kernel reserved operations
without impacting the ULP user.
The low level driver can register a non-zero value which
will be transparently added to the send queue size and hidden
from the ULP in every respect.
ULP post sends will never see a full queue due to a reserved
post send and reserved operations will never exceed that
registered value.
The s_avail will continue to track the ULP swqe availability
and the difference between the reserved value and the reserved
in use will track reserved availabity.
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Some work requests are local operations, such as IB_WR_REG_MR and
IB_WR_LOCAL_INV. They differ from non-local operations in that:
(1) Local operations can be processed immediately without being posted
to the send queue if neither fencing nor completion generation is needed.
However, to ensure correct ordering, once a local operation is posted to
the work queue due to fencing or completion requiement, all subsequent
local operations must also be posted to the work queue until all the
local operations on the work queue have completed.
(2) Local operations don't send packets over the wire and thus don't
need (and shouldn't update) the packet sequence numbers.
Define a new a flag bit for the post send table to identify local
operations.
Add a new field to the QP structure to track the number of local
operations on the send queue to determine if direct processing of new
local operations should be enabled/disabled.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jianxin Xiong <jianxin.xiong@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Add flexibility for driver dependent operations in post send
because different drivers will have differing post send
operation support.
This includes data structure definitions to support a table
driven scheme along with the necessary validation routine
using the new table.
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Reviewed-by: Jianxin Xiong <jianxin.xiong@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
rdmavt allows the driver to specify the size of the ack queue, but
only uses it for the modify QP limit testing for setting the atomic
limit value.
The driver dependent size is now used to size the s_ack_queue ring
dynamicially.
Since the driver knows its size, the driver will use its define
for any ring size dependent code.
Reviewed-by: Mitko Haralanov <mitko.haralanov@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The RVT_S_WAIT_PIO_DRAIN flag was missing from
the set of flags indicating a qp is waiting
on a resource.
This caused the sleep/wakeup for adaptive pio
drain to lose a wakeup "hanging" a QP.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Tracking user/QP ownership is needed to debug issues with
user ULPs like OpenMPI.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The change requires a new pio_busy field in the iowait structure to
track the number of outstanding pios. The new counter together
with the sdma counter serve as the basis for a packet by packet decision
as to which egress mechanism to use. Since packets given to different
egress mechanisms are not ordered, this scheme will preserve the order.
The iowait drain/wait mechanisms are extended for a pio case. An
additional qp wait flag is added for the PIO drain wait case.
Currently the only pio wait is for buffers, so the no_bufs_available()
routine name is changed to pio_wait() and a third argument is passed
with one of the two pio wait flags to generalize the routine. A module
parameter is added to hold a configurable threshold. For now, the
module parameter is zero.
A heuristic routine is added to return the func pointer of the proper
egress routine to use.
The heuristic is as follows:
- SMI always uses pio
- GSI,UD qps <= threshold use pio
- UD qps > threadhold use sdma
o No coordination with sdma is required because order is not required
and this qp pio count is not maintained for UD
- RC/UC ONLY packets <= threshold chose as follows:
o If sdmas pending, use SDMA
o Otherwise use pio and enable the pio tracking count at
the time the pio buffer is allocated
- RC/UC ONLY packets > threshold use SDMA
o If pio's are pending the pio_wait with the new wait flag is
called to delay for pios to drain
The threshold is potentially reduced by the QP's mtu.
The sc_buffer_alloc() has two additional args (a callback, a void *)
which are exploited by the RC/UC cases to pass a new complete routine
and a qp *.
When the shadow ring completes the credit associated with a packet,
the new complete routine is called. The verbs_pio_complete() will then
decrement the busy count and trigger any drain waiters in qp destroy
or reset.
Reviewed-by: Jubin John <jubin.john@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
pahole noted the wasted 4 bytes after s_lock and r_lock.
Move s_flags and r_psn to fill the holes.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Remove exported functions which are no longer required as the
functionality has moved into rdmavt. This also requires re-ordering some
of the functions since their prototype no longer appears in a header
file. Rather than add forward declarations it is just cleaner to
re-order some of the functions.
Reviewed-by: Jubin John <jubin.john@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
This patch adds an additional lock to reduce contention on the s_lock.
This lock is used in post_send() so that the post_send is not
serialized with the send engine and other send related processing.
To do this the s_next_psn is now maintained on post_send() while
post_send() related fields are moved to a new cache line. There is
an s_avail maintained for the post_send() to mitigate trading cache
lines with the send engine. The lock is released/acquired around
releasing the just built packet to the egress mechanism.
Reviewed-by: Jubin John <jubin.john@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Harish Chegondi <harish.chegondi@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
A busy_jiffies variable is maintained and updated when rc qps are
created and deleted. busy_jiffies is a scaled value of the number
of rc qps in the device. busy_jiffies is incremented every rc qp
scaling interval. busy_jiffies is added to the rc timeout
in add_retry_timer and mod_retry_timer. The rc qp scaling interval
is selected based on extensive performance evaluation of targeted
workloads.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Vennila Megavannan <vennila.megavannan@intel.com>
Signed-off-by: Jubin John <jubin.john@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The field is a vestige from ipath.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Update all files added by rdmavt which do not yet have 2016 as the
copyright year.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Harish Chegondi <harish.chegondi@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
s_sde should be in the low level driver QP private data.
Remove the definition from rvt_qp.
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
This patch adds in the multicast add and remove functions as well as the
ancillary infrastructure needed.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Add modify qp and supporting functions.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Add in a post_send and post_one_send to rdmavt. The ULP will provide a WQE
to rdmavt which will then walk and queue each element. Rdmavt will then
queue the work to be done in the driver or kick the driver's progress
routine.
There needs to be a follow on patch which adds in another lock for the
head of the queue so that it can be added to and read from in parallel.
This will touch protocol handlers and require other changes in the
drivers. This will be done separately.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Until all queue pair functionality is moved to rdmavt we need to provide
access to the reset function. This is only temporary and will be reverted
back to a static, non exported function in the end.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Harish Chegondi <harish.chegondi@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Use the flags originally provided for hfi1 in the rdmavt driver. These will
be made available to drivers in the qp header file.
Reviewed-by: Harish Chegondi <harish.chegondi@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Add table init as well as teardown for handling qpn maps. Drivers can still
provide this functionality by setting the QP_INIT_DRIVER bit.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Until all functionality is moved over to rdmavt drivers still need to
access a number of fields in data structures that are predominantly
meant to be used by rdmavt. Once these rdmavt_<ibta_object>.h header
files are no longer being touched by drivers their content should be
moved to rdmavt/<ibta_object>.h. While here move a couple #defines
over to more general IB verbs header files because they fit better.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
Mike Marciniszyn
Brian Welty
Sebastian Sanchez
Doug Ledford
Kaike Wan
Don Hiatt
Dasaratharaman Chandramouli
Michael J. Ruhl
Venkata Sandeep Dhanalakota
Ira Weiny
Jianxin Xiong
Dennis Dalessandro
Vennila Megavannan