| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
To add the Online controller reset support, driver need to do:
a). reset the controller chips -- Xscale and Gen2 which will change
the function calls and add the reset function related to this two
chips.
b). during the reset, driver will store the pending cmds which not
returned by FW to driver's pending queue. Driver will re-issue those
pending cmds again to FW after the OCR finished.
c). In driver's timeout routine, driver will report to OS as reset.
Also driver's queue routine will block the cmds until the OCR
finished.
d). in Driver's ISR routine, if driver get the FW state as state
change, FW in Failure status and FW support online controller
reset (OCR), driver will start to do the controller reset.
e). In driver's IOCTL routine, the application cmds will wait for the
OCR to finish, then issue the cmds to FW.
Signed-off-by Bo Yang <bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Update lpfc driver version to 8.3.17
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Replace graceful teardown steps with the singular function reset command.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
- Fail I/Os with incomplete data that complete with SCSI Check condition.
- Complete aborted I/Os with host_scribble equal to NULL with success.
- Initialize context1 field of iocbq in the new_scsi_buf routines.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
- Add support for bsg MBX_SLI4_CONFIG.
- Multiply linkup timeout in loopback test code by 100.
- Set iocb_stat to 0 in the lpfcdiag_loop_get_xri function.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
- Added driver support for management application to pass down two security
specific mailbox commands (MBX_SECURITY_MGMT and MBX_AUTH_PORT)
- Added driver support for handling FIPS zeroization trap of host ERATT ER8,
performing selective reset and bringing the device up.
- Added code to detect INIT_LINK mailbox command completion returning status
MBXERR_SEC_NO_PERMISSION.
- Increased the wait timeout on host status register HS_FFRDY and HS_MBRDY
being set.
- Remove the port offline code from the Heartbeat TMO handler.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
- Move Unload flag earlier in vport deletei to stop ELS traffic
- Replaced some unnecessary spin_lock_irqsave with spin_lock_irq
- Fixed circular spinlock dependency between low-level driver and SCSI midlayer
- Remove duplicate code from lpfc_els_retry routine
- Make all error values negative
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
With the change that drivers have to explicitly request the serial
number for SCSI commands, this field should not be part of the zfcp
traces. It is not worth the effort to request the serial number only
for tracing purposes, so simply remove this field from the debug
traces.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
The structure definitions for reporting array errors did not have the correct
size for the Array WWID field. This patch fixes those definitions. It also
fixes part of the output formatting that did not have newlines and fixes size
calculations.
Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
It was disabled when x86_64 was introduced, but it is reported to be
working on 64bit by two different people, so let's enable it back
again.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: "Juergen E. Fischer" <fischer@norbit.de>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
For ALUA we should be handling all states, independent of whether
the mode is explicit or implicit. For 'Transitioning' we should retry
for a certain amount of time; after that we're setting the port
to 'Standby' and return SCSI_DH_RETRY to signal upper layers
a retry is in order here.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Update cxgb4i connection setting and pagepod programming.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Signed-off-by: Karen Xie <kxie@chelsio.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Fixed the locking and releasing skb in the case of error in the pdu
read path, and added define iscsi_task_cxgbi_data to access the
private data inside the iscsi_task.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Signed-off-by: Karen Xie <kxie@chelsio.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
If a Virtual I/O server is rebooted, the client fibre channel sees a
transport event on its CRQ, which causes it to attempt to reconnect
to the CRQ. For a period of time during the VIOS reboot, the client's
attempts to register the CRQ will return H_CLOSED, indicating the server
side is not currently registered. The ibmvfc driver was not handling
this well and was taking the virtual adapter offline. Fix this by
re-enabling our interrupt and waiting for the event on our CRQ
indicating the server is back, at which point we can reconnect.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Following a site power outage which re-enabled all the ports on my FC
switches, my system subsequently booted with far too many luns! I had
let it run hoping it would make multi-user. It didn't. :( It hung solid
after exhausting the last sd device, sdzzz, and attempting to create sdaaaa
and beyond. I was unable to get a dump.
Discovered using a 2.6.32.13 based system.
correct this by detecting when the last index is utilized and failing
the sd probe of the device. Patch applies to scsi-misc-2.6.
Signed-off-by: Michael Reed <mdr@sgi.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
This adds a fc host dev loss sysfs file. Instead of
calling into the driver using the get_host_def_dev_loss_tmo
callback, we allow drivers to init the dev loss like is done
for other fc host params, and then the fc class will handle
updating the value if the user writes to the new sysfs file.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
This removes the driver's get_host_def_dev_loss_tmo
callback and just has the driver set the dev loss
using the fc class fc_host_dev_loss_tmo macro like is
done for other fc params.
It also adds compat support for the driver's existing
dev loss and nodev sysfs and modparams.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
This removes the driver's get_host_def_dev_loss_tmo
callback and just has the driver set the dev loss
using the fc class fc_host_dev_loss_tmo macro like is
done for other fc params.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
This removes the driver's get_host_def_dev_loss_tmo
callback and just has the driver set the dev loss
using the fc class fc_host_dev_loss_tmo macro like is
done for other fc params.
This patch also removes the module dev loss param.
To override the value the fc host sysfs value being
added in the fc class patch can be used instead of the driver
module param.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
This removes the driver's get_host_def_dev_loss_tmo
callback and just has the driver set the dev loss
using the fc class fc_host_dev_loss_tmo macro like is
done for other fc params.
This also adds a set rport dev loss function so the
fc class host dev loss tmp sysfs support being added
in the fc class patch can update rports.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
We use read/write[bslq] but do not include linux/io.h. This causes
build failures on PPC. Include that file.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Stable Tree <stable@kernel.org>
Acked-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Some cards (like mvsas) have issue troubles if non-NCQ commands are
mixed with NCQ ones. Fix this by using the libata default NCQ check
routine which waits until all NCQ commands are complete before issuing
a non-NCQ one. The impact to cards (like aic94xx) which don't need
this logic should be minimal
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Add support for the Thin Provisioning VPD page and use the TPU and TPWS
bits to switch between UNMAP and WRITE SAME(16) for discards. If no TP
VPD page is present we fall back to old scheme where the max descriptor
count combined with the max lba count are used trigger UNMAP.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
We have flattened the BFA hierarchy and also reduced the number of
source and header files we used to have earlier.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Replace the zfcp_modify_<xxx>_status functions and its accompanying wrappers
with dedicated status modifier functions. This eases code readability and
maintenance.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
The steps for setting the zfcp_adapter online are the same in
zfcp_ccw_set_online and zfcp_ccw_activate. Remove the code duplication
by calling zfcp_ccw_activate from zfcp_ccw_set_online.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Move the code evaluating the ACL/CFDC specific errors to the file
zfcp_cfdc.c. With this change, all code related to the old access
control feature is kept in one file, not split across zfcp_erp.c and
zfcp_fsf.c.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Instead of calling the same handler for both, I/O and task management
commands, use different handlers that call a function for the common
part.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
With the change to use the data on the SCSI device, iterating through
all LUNs/scsi_devices takes the SCSI host_lock. This triggers warnings
from the lock dependency checker:
=========================================================
[ INFO: possible irq lock inversion dependency detected ]
2.6.34.1 #97
---------------------------------------------------------
chchp/3224 just changed the state of lock:
(&(shost->host_lock)->rlock){-.-...}, at: [<00000000003a73f4>] __scsi_iterate_devices+0x38/0xbc
but this lock took another, HARDIRQ-unsafe lock in the past:
(&(&qdio->req_q_lock)->rlock){+.-...}
and interrupts could create inverse lock ordering between them.
other info that might help us debug this: [ 24.972394] 2 locks held by chchp/3224:
#0: (&(sch->lock)->rlock){-.-...}, at: [<0000000000401efa>] do_IRQ+0xb2/0x1e4
#1: (&adapter->port_list_lock){.-....}, at: [<0000000000490302>] zfcp_erp_modify_adapter_status+0x9e/0x16c
[...]
=========================================================
[ INFO: possible irq lock inversion dependency detected ]
2.6.34.1 #98
---------------------------------------------------------
chchp/3235 just changed the state of lock:
(&(shost->host_lock)->rlock){-.-...}, at: [<00000000003a73f4>] __scsi_iterate_devices+0x38/0xbc
but this lock took another, HARDIRQ-unsafe lock in the past:
(&(&qdio->stat_lock)->rlock){+.-...}
and interrupts could create inverse lock ordering between them.
other info that might help us debug this:
2 locks held by chchp/3235:
#0: (&(sch->lock)->rlock){-.-...}, at: [<0000000000401efa>] do_IRQ+0xb2/0x1e4
#1: (&adapter->port_list_lock){.-.-..}, at: [<00000000004902f6>] zfcp_erp_modify_adapter_status+0x9e/0x16c
[...]
To stop this warning, change the request queue lock to disable irqs,
not only softirq. The changes are required only outside of the
critical "send fcp command" path.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Enable the LUN scanning mechanism in the SCSI midlayer:
- Do not set the disable_target_scan bit in the FC transport class.
- Set max_lun to 0xFFFFFFFF to allow the midlayer scan to include
the two-level hierachical LUNs (like 0x40XX40XX00000000, but in SCSI
midlayer LUN format).
- Set max_id to a high value to allow triggering the SCSI device
rescan from sysfs.
When running in NPIV mode, zfcp accepts all LUNs in slave_attach. When
running in non-NPIV mode, the list of zfcp_unit structs determines
which SCSI devices are allowed on the current system.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
This is the large change to switch from using the data in
zfcp_unit to zfcp_scsi_dev. Keeping everything working requires doing
the switch in one piece. To ensure that no code keeps using the data
in zfcp_unit, this patch also removes the data from zfcp_unit that is
now being replaced with zfcp_scsi_dev.
For zfcp, the scsi_device together with zfcp_scsi_dev exist from the
call of slave_alloc to the call of slave_destroy. The data in
zfcp_scsi_dev is initialized in zfcp_scsi_slave_alloc and the LUN is
opened; the final shutdown for the LUN is run from slave_destroy.
Where the scsi_device or zfcp_scsi_dev is needed, the pointer to the
scsi_device is passed as function argument and inside the function
converted to the pointer to zfcp_scsi_dev; this avoids back and forth
conversion betweeen scsi_device and zfcp_scsi_dev.
While changing the function arguments from zfcp_unit to scsi_device,
the functions names are renamed form "unit" to "lun". This is to have
a seperation between zfcp_scsi_dev/LUN and the zfcp_unit; only code
referring to the remaining configuration information in zfcp_unit
struct uses "unit".
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
With the change for the LUN data to be part of the scsi_device, the
slave_destroy callback will be the final call to the
zfcp_erp_unit_shutdown function. The erp tries to acquire a reference
to run the action asynchronously and fail, if it cannot get the
reference. But calling scsi_device_get from slave_destroy will fail,
because the scsi_device is already in the state SDEV_DEL.
Introduce a new call into the zfcp erp to solve this: The function
zfcp_erp_unit_shutdown_wait will close the LUN and wait for the erp to
finish without acquiring an additional reference. The wait allows to
omit the reference; the caller waiting for the erp to finish already
has a reference that holds the struct in place.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
These sysfs attributes will require different functions. Implement
them without using macros, so that the open coded functions can be
changed later.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Move the code for managing zfcp_unit devices to the new file
zfcp_unit.c. This is in preparation for the change that zfcp_unit will
only track the LUNs configured via unit_add, other data will be moved
from zfcp_unit to the new struct zfcp_scsi_dev.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Add a new data structure zfcp_scsi_dev that holds zfcp private data
for each SCSI device. Use scsi_transport_reserve_device to let the
SCSI midlayer automatically allocate this with each SCSI device.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
By default, ibmvfc does not log any async events in order
to avoid flooding the log with them. Improve on this by
logging by default events that are not likely to flood the
log, such as link up/down. Having these events in the log
will improve the ability to debug issues with ibmvfc.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Get rid of init_MUTEX[_LOCKED]() and use sema_init() instead.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: aacraid@adaptec.com
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
This patch updates the scsi_debug virtual LLD to use
root_device_register() and root_device_unregister() from
include/linux/device.h instead of device_register() and
device_unregister() respectively within scsi_debug_init() and
scsi_debug_exit() This simply involved converting the static struct
device pseudo_primary into a pointer that is setup by the call to
root_device_register().
This patch also contains the correct IS_ERR() conditional check of
root_device_register() from within scsi_debug_init().
Thanks to Richard Sharpe and Dmitry Torokhov for their help with this
item.
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
When an rport is "blocked" and a bsg request is received, the bsg request gets
placed on the queue but the queue stalls. If the fc object is then deleted - the
bsg queue never restarts and keeps the reference on the object, and stops the
overall teardown.
This patch restarts the bsg queue on teardown and drains any pending requests,
allowing the teardown to succeed.
Signed-off-by: Carl Lajeunesse <carl.lajeunesse@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Make sure that the rport registration did complete and then register
SCSI device directly. Otherwise the unit_enqueue would race with the
call to zfcp_scsi_queue_unit_register.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
The isr optimization patch that was submitted a few months ago
exposed problems with receiving and handling spurious HRRQ interrutps.
commit 64ffdb762241c0a9c0c8fac7ea92aa0ba1529334
Author: Wayne Boyer <wayneb@linux.vnet.ibm.com>
Date: Wed May 19 11:56:13 2010 -0700
[SCSI] ipr: improve interrupt service routine performance
That patch is reverted with this one. A new patch will be submitted
once the issue is better understood and properly handled in the driver.
Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
The previous thin provisioning support was not very user friendly
because it depended on all the relevant options being set on the command
line.
Implement support for the Thin Provisioning VPD page from SBC3 r24 and
add module options for TPU (UNMAP) and TPWS (WRITE SAME (16) with UNMAP
bit). This allows us to have sane default and to enable thin
provisioning with a simple tpu=1 or tpws=1 on the command line depending
on whether we want UNMAP or WRITE SAME behavior.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Fix kconfig dependency warnings in scsi/Kconfig:
warning: (SCSI_SAS_LIBSAS && SCSI || SCSI_MPT2SAS && SCSI_LOWLEVEL && PCI && SCSI || FUSION_SAS && FUSION && PCI && SCSI) selects SCSI_SAS_ATTRS which has unmet direct dependencies (SCSI && BLK_DEV_BSG)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Return -ENOMEM if the allocations fail.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Fix typo in scsi_transport_iscsi.c kernel-doc notation:
Warning(drivers/scsi/scsi_transport_iscsi.c:548): No description found for parameter 'cmd'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Return recovered from pci_mmio_enabled function if it is 82XX.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
The sg table size is increased from 128 to 1024 to support multiple sg lists
and number of sg elements per scsi command.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
bo yang
James Smart
Christof Schmitt
Wayne Boyer
Jiri Slaby
Hannes Reinecke
kxie@chelsio.com
Brian King
Michael Reed
Mike Christie
David Milburn
Martin K. Petersen
Krishna Gudipati
Swen Schillig
Shyam Sundar
Thomas Gleixner
Nicholas Bellinger
Randy Dunlap
Dan Carpenter
Saurav Kashyap
Giridhar Malavali