| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Using devlink-sb, we can configure 12/16 (the important 75%) of the
switch's controlling watermarks for congestion drops, and we can monitor
50% of the watermark occupancies (we can monitor the reservation
watermarks, but not the sharing watermarks, which are exposed as pool
sizes).
The following definitions can be made:
SB_BUF=0 # The devlink-sb for frame buffers
SB_REF=1 # The devlink-sb for frame references
POOL_ING=0 # The pool for ingress traffic. Both devlink-sb instances
# have one of these.
POOL_EGR=1 # The pool for egress traffic. Both devlink-sb instances
# have one of these.
Editing the hardware watermarks is done in the following way:
BUF_xxxx_I is accessed when sb=$SB_BUF and pool=$POOL_ING
REF_xxxx_I is accessed when sb=$SB_REF and pool=$POOL_ING
BUF_xxxx_E is accessed when sb=$SB_BUF and pool=$POOL_EGR
REF_xxxx_E is accessed when sb=$SB_REF and pool=$POOL_EGR
Configuring the sharing watermarks for COL_SHR(dp=0) is done implicitly
by modifying the corresponding pool size. By default, the pool size has
maximum size, so this can be skipped.
devlink sb pool set pci/0000:00:00.5 sb $SB_BUF pool $POOL_ING \
size 129840 thtype static
Since by default there is no buffer reservation, the above command has
maxed out BUF_COL_SHR_I(dp=0).
Configuring the per-port reservation watermark (P_RSRV) is done in the
following way:
devlink sb port pool set pci/0000:00:00.5/0 sb $SB_BUF \
pool $POOL_ING th 1000
The above command sets BUF_P_RSRV_I(port 0) to 1000 bytes. After this
command, the sharing watermarks are internally reconfigured with 1000
bytes less, i.e. from 129840 bytes to 128840 bytes.
Configuring the per-port-tc reservation watermarks (Q_RSRV) is done in
the following way:
for tc in {0..7}; do
devlink sb tc bind set pci/0000:00:00.5/0 sb 0 tc $tc \
type ingress pool $POOL_ING \
th 3000
done
The above command sets BUF_Q_RSRV_I(port 0, tc 0..7) to 3000 bytes.
The sharing watermarks are again reconfigured with 24000 bytes less.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add devlink integration into the mscc_ocelot switchdev driver. All
physical ports (i.e. the unused ones as well) except the CPU port module
at ocelot->num_phys_ports are registered with devlink, and that requires
keeping the devlink_port structure outside struct ocelot_port_private,
since the latter has a 1:1 mapping with a struct net_device (which does
not exist for unused ports).
Since we use devlink_port_type_eth_set to link the devlink port to the
net_device, we can as well remove the .ndo_get_phys_port_name and
.ndo_get_port_parent_id implementations, since devlink takes care of
retrieving the port name and number automatically, once
.ndo_get_devlink_port is implemented.
Note that the felix DSA driver is already integrated with devlink by
default, since that is a thing that the DSA core takes care of. This is
the reason why these devlink stubs were put in ocelot_net.c and not in
the common library. It is also the reason why ocelot::devlink is a
pointer and not a full structure embedded inside struct ocelot: because
the mscc_ocelot driver allocates that by itself (as the container of
struct ocelot, in fact), but in the case of felix, it is DSA who
allocates the devlink, and felix just propagates the pointer towards
struct ocelot.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We should be moving anything that isn't DSA-specific or SoC-specific out
of the felix DSA driver, and into the common mscc_ocelot switch library.
The number of traffic classes is one of the aspects that is common
between all ocelot switches, so it belongs in the library.
This patch also makes seville use 8 TX queues, and therefore enables
prioritization via the QOS_CLASS field in the NPI injection header.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We'll need to read back the watermark thresholds and occupancy from
hardware (for devlink-sb integration), not only to write them as we did
so far in ocelot_port_set_maxlen. So introduce 2 new functions in struct
ocelot_ops, similar to wm_enc, and implement them for the 3 supported
mscc_ocelot switches.
Remove the INUSE and MAXUSE unpacking helpers for the QSYS_RES_STAT
register, because that doesn't scale with the number of switches that
mscc_ocelot supports now. They have different bit widths for the
watermarks, and we need function pointers to abstract that difference
away.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Instead of reading these values from the reference manual and writing
them down into the driver, it appears that the hardware gives us the
option of detecting them dynamically.
The number of frame references corresponds to what the reference manual
notes, however it seems that the frame buffers are reported as slightly
less than the books would indicate. On VSC9959 (Felix), the books say it
should have 128KB of packet buffer, but the registers indicate only
129840 bytes (126.79 KB). Also, the unit of measurement for FREECNT from
the documentation of all these devices is incorrect (taken from an older
generation). This was confirmed by Younes Leroul from Microchip support.
Not having anything better to do with these values at the moment* (this
will change soon), let's just print them.
*The frame buffer size is, in fact, used to calculate the tail dropping
watermarks.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Introduce the header file include/soc/canaan/k210-sysctl.h to have a
common definition of the Canaan Kendryte K210 SoC system controller
registers. Simplify the k210 system controller driver code by removing
unused register bits definition. The MAINTAINERS file is updated,
adding the entry "CANAAN/KENDRYTE K210 SOC SYSTEM CONTROLLER DRIVER"
with myself listed as maintainer for this driver.
This is a preparatory patch for introducing the K210 clock driver. No
functional changes are introduced.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
|
Since the introduction of the switchdev API, port attributes were
transmitted to drivers for offloading using a two-step transactional
model, with a prepare phase that was supposed to catch all errors, and a
commit phase that was supposed to never fail.
Some classes of failures can never be avoided, like hardware access, or
memory allocation. In the latter case, merely attempting to move the
memory allocation to the preparation phase makes it impossible to avoid
memory leaks, since commit 91cf8eceffc1 ("switchdev: Remove unused
transaction item queue") which has removed the unused mechanism of
passing on the allocated memory between one phase and another.
It is time we admit that separating the preparation from the commit
phase is something that is best left for the driver to decide, and not
something that should be baked into the API, especially since there are
no switchdev callers that depend on this.
This patch removes the struct switchdev_trans member from switchdev port
attribute notifier structures, and converts drivers to not look at this
member.
In part, this patch contains a revert of my previous commit 2e554a7a5d8a
("net: dsa: propagate switchdev vlan_filtering prepare phase to
drivers").
For the most part, the conversion was trivial except for:
- Rocker's world implementation based on Broadcom OF-DPA had an odd
implementation of ofdpa_port_attr_bridge_flags_set. The conversion was
done mechanically, by pasting the implementation twice, then only
keeping the code that would get executed during prepare phase on top,
then only keeping the code that gets executed during the commit phase
on bottom, then simplifying the resulting code until this was obtained.
- DSA's offloading of STP state, bridge flags, VLAN filtering and
multicast router could be converted right away. But the ageing time
could not, so a shim was introduced and this was left for a further
commit.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Reviewed-by: Linus Walleij <linus.walleij@linaro.org> # RTL8366RB
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Requests sent to RPMH can be sent as fire-n-forget or response required,
with the latter ensuring the command has been completed by the hardware
accelerator. Commands in a request with tcs_cmd::wait set, would ensure
that those select commands are sent as response required, even though
the actual TCS request may be fire-n-forget.
Also, commands with .wait flag were also guaranteed to be complete
before the following command in the TCS is sent. This means that the
next command of the same request blocked until the current request is
completed. This could mean waiting for a voltage to settle or series of
NOCs be configured before the next command is sent. But drivers using
this feature have never cared about the serialization aspect. By not
enforcing the serialization we can allow the hardware to run in parallel
improving the performance.
Let's clarify the usage of this member in the tcs_cmd structure to mean
only completion and not serialization. This should also improve the
performance of bus requests where changes could happen in parallel.
Also, CPU resume from deep idle may see benefits from certain wake
requests.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Link: https://lore.kernel.org/r/1610008770-13891-1-git-send-email-mkshah@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
NPS platform has been removed from ARC port and there are no in-tree
user of it now . So RIP !
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
Add modularization support to the Tegra124 EMC driver, which now can be
compiled as a loadable kernel module.
Note that EMC clock must be registered at clk-init time, otherwise PLLM
will be disabled as unused clock at boot time if EMC driver is compiled
as a module. Hence add a prepare/complete callbacks. similarly to what is
done for the Tegra20/30 EMC drivers.
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20201228154920.18846-2-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Pull ARM SoC driver updates from Arnd Bergmann:
"There are a couple of subsystems maintained by other people that merge
their drivers through the SoC tree, those changes include:
- The SCMI firmware framework gains support for sensor notifications
and for controlling voltage domains.
- A large update for the Tegra memory controller driver, integrating
it better with the interconnect framework
- The memory controller subsystem gains support for Mediatek MT8192
- The reset controller framework gains support for sharing pulsed
resets
For Soc specific drivers in drivers/soc, the main changes are
- The Allwinner/sunxi MBUS gets a rework for the way it handles
dma_map_ops and offsets between physical and dma address spaces.
- An errata fix plus some cleanups for Freescale Layerscape SoCs
- A cleanup for renesas drivers regarding MMIO accesses.
- New SoC specific drivers for Mediatek MT8192 and MT8183 power
domains
- New SoC specific drivers for Aspeed AST2600 LPC bus control and SoC
identification.
- Core Power Domain support for Qualcomm MSM8916, MSM8939, SDM660 and
SDX55.
- A rework of the TI AM33xx 'genpd' power domain support to use
information from DT instead of platform data
- Support for TI AM64x SoCs
- Allow building some Amlogic drivers as modules instead of built-in
Finally, there are numerous cleanups and smaller bug fixes for
Mediatek, Tegra, Samsung, Qualcomm, TI OMAP, Amlogic, Rockchips,
Renesas, and Xilinx SoCs"
* tag 'arm-soc-drivers-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (222 commits)
soc: mediatek: mmsys: Specify HAS_IOMEM dependency for MTK_MMSYS
firmware: xilinx: Properly align function parameter
firmware: xilinx: Add a blank line after function declaration
firmware: xilinx: Remove additional newline
firmware: xilinx: Fix kernel-doc warnings
firmware: xlnx-zynqmp: fix compilation warning
soc: xilinx: vcu: add missing register NUM_CORE
soc: xilinx: vcu: use vcu-settings syscon registers
dt-bindings: soc: xlnx: extract xlnx, vcu-settings to separate binding
soc: xilinx: vcu: drop useless success message
clk: samsung: mark PM functions as __maybe_unused
soc: samsung: exynos-chipid: initialize later - with arch_initcall
soc: samsung: exynos-chipid: order list of SoCs by name
memory: jz4780_nemc: Fix potential NULL dereference in jz4780_nemc_probe()
memory: ti-emif-sram: only build for ARMv7
memory: tegra30: Support interconnect framework
memory: tegra20: Support hardware versioning and clean up OPP table initialization
dt-bindings: memory: tegra20-emc: Document opp-supported-hw property
soc: rockchip: io-domain: Fix error return code in rockchip_iodomain_probe()
reset-controller: ti: force the write operation when assert or deassert
...
|
|
Pull power management updates from Rafael Wysocki:
"These update cpufreq (core and drivers), cpuidle (polling state
implementation and the PSCI driver), the OPP (operating performance
points) framework, devfreq (core and drivers), the power capping RAPL
(Running Average Power Limit) driver, the Energy Model support, the
generic power domains (genpd) framework, the ACPI device power
management, the core system-wide suspend code and power management
utilities.
Specifics:
- Use local_clock() instead of jiffies in the cpufreq statistics to
improve accuracy (Viresh Kumar).
- Fix up OPP usage in the cpufreq-dt and qcom-cpufreq-nvmem cpufreq
drivers (Viresh Kumar).
- Clean up the cpufreq core, the intel_pstate driver and the
schedutil cpufreq governor (Rafael Wysocki).
- Fix up error code paths in the sti-cpufreq and mediatek cpufreq
drivers (Yangtao Li, Qinglang Miao).
- Fix cpufreq_online() to return error codes instead of success (0)
in all cases when it fails (Wang ShaoBo).
- Add mt8167 support to the mediatek cpufreq driver and blacklist
mt8516 in the cpufreq-dt-platdev driver (Fabien Parent).
- Modify the tegra194 cpufreq driver to always return values from the
frequency table as the current frequency and clean up that driver
(Sumit Gupta, Jon Hunter).
- Modify the arm_scmi cpufreq driver to allow it to discover the
power scale present in the performance protocol and provide this
information to the Energy Model (Lukasz Luba).
- Add missing MODULE_DEVICE_TABLE to several cpufreq drivers (Pali
Rohár).
- Clean up the CPPC cpufreq driver (Ionela Voinescu).
- Fix NVMEM_IMX_OCOTP dependency in the imx cpufreq driver (Arnd
Bergmann).
- Rework the poling interval selection for the polling state in
cpuidle (Mel Gorman).
- Enable suspend-to-idle for PSCI OSI mode in the PSCI cpuidle driver
(Ulf Hansson).
- Modify the OPP framework to support empty (node-less) OPP tables in
DT for passing dependency information (Nicola Mazzucato).
- Fix potential lockdep issue in the OPP core and clean up the OPP
core (Viresh Kumar).
- Modify dev_pm_opp_put_regulators() to accept a NULL argument and
update its users accordingly (Viresh Kumar).
- Add frequency changes tracepoint to devfreq (Matthias Kaehlcke).
- Add support for governor feature flags to devfreq, make devfreq
sysfs file permissions depend on the governor and clean up the
devfreq core (Chanwoo Choi).
- Clean up the tegra20 devfreq driver and deprecate it to allow
another driver based on EMC_STAT to be used instead of it (Dmitry
Osipenko).
- Add interconnect support to the tegra30 devfreq driver, allow it to
take the interconnect and OPP information from DT and clean it up
(Dmitry Osipenko).
- Add interconnect support to the exynos-bus devfreq driver along
with interconnect properties documentation (Sylwester Nawrocki).
- Add suport for AMD Fam17h and Fam19h processors to the RAPL power
capping driver (Victor Ding, Kim Phillips).
- Fix handling of overly long constraint names in the powercap
framework (Lukasz Luba).
- Fix the wakeup configuration handling for bridges in the ACPI
device power management core (Rafael Wysocki).
- Add support for using an abstract scale for power units in the
Energy Model (EM) and document it (Lukasz Luba).
- Add em_cpu_energy() micro-optimization to the EM (Pavankumar
Kondeti).
- Modify the generic power domains (genpd) framwework to support
suspend-to-idle (Ulf Hansson).
- Fix creation of debugfs nodes in genpd (Thierry Strudel).
- Clean up genpd (Lina Iyer).
- Clean up the core system-wide suspend code and make it print driver
flags for devices with debug enabled (Alex Shi, Patrice Chotard,
Chen Yu).
- Modify the ACPI system reboot code to make it prepare for system
power off to avoid confusing the platform firmware (Kai-Heng Feng).
- Update the pm-graph (multiple changes, mostly usability-related)
and cpupower (online and offline CPU information support) PM
utilities (Todd Brandt, Brahadambal Srinivasan)"
* tag 'pm-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (86 commits)
cpufreq: Fix cpufreq_online() return value on errors
cpufreq: Fix up several kerneldoc comments
cpufreq: stats: Use local_clock() instead of jiffies
cpufreq: schedutil: Simplify sugov_update_next_freq()
cpufreq: intel_pstate: Simplify intel_cpufreq_update_pstate()
PM: domains: create debugfs nodes when adding power domains
opp: of: Allow empty opp-table with opp-shared
dt-bindings: opp: Allow empty OPP tables
media: venus: dev_pm_opp_put_*() accepts NULL argument
drm/panfrost: dev_pm_opp_put_*() accepts NULL argument
drm/lima: dev_pm_opp_put_*() accepts NULL argument
PM / devfreq: exynos: dev_pm_opp_put_*() accepts NULL argument
cpufreq: qcom-cpufreq-nvmem: dev_pm_opp_put_*() accepts NULL argument
cpufreq: dt: dev_pm_opp_put_regulators() accepts NULL argument
opp: Allow dev_pm_opp_put_*() APIs to accept NULL opp_table
opp: Don't create an OPP table from dev_pm_opp_get_opp_table()
cpufreq: dt: Don't (ab)use dev_pm_opp_get_opp_table() to create OPP table
opp: Reduce the size of critical section in _opp_kref_release()
PM / EM: Micro optimization in em_cpu_energy
cpufreq: arm_scmi: Discover the power scale in performance protocol
...
|
|
Currently ocelot_set_rx_mode calls ocelot_mact_learn directly, which has
a very nice ocelot_mact_wait_for_completion at the end. Introduced in
commit 639c1b2625af ("net: mscc: ocelot: Register poll timeout should be
wall time not attempts"), this function uses readx_poll_timeout which
triggers a lot of lockdep warnings and is also dangerous to use from
atomic context, potentially leading to lockups and panics.
Steen Hegelund added a poll timeout of 100 ms for checking the MAC
table, a duration which is clearly absurd to poll in atomic context.
So we need to defer the MAC table access to process context, which we do
via a dynamically allocated workqueue which contains all there is to
know about the MAC table operation it has to do.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20201212191612.222019-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
xdp_return_frame_bulk() needs to pass a xdp_buff
to __xdp_return().
strlcpy got converted to strscpy but here it makes no
functional difference, so just keep the right code.
Conflicts:
net/netfilter/nf_tables_api.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The current assumption is that the felix DSA driver has flooding knobs
per traffic class, while ocelot switchdev has a single flooding knob.
This was correct for felix VSC9959 and ocelot VSC7514, but with the
introduction of seville VSC9953, we see a switch driven by felix.c which
has a single flooding knob.
So it is clear that we must do what should have been done from the
beginning, which is not to overwrite the configuration done by ocelot.c
in felix, but instead to teach the common ocelot library about the
differences in our switches, and set up the flooding PGIDs centrally.
The effect that the bogus iteration through FELIX_NUM_TC has upon
seville is quite dramatic. ANA_FLOODING is located at 0x00b548, and
ANA_FLOODING_IPMC is located at 0x00b54c. So the bogus iteration will
actually overwrite ANA_FLOODING_IPMC when attempting to write
ANA_FLOODING[1]. There is no ANA_FLOODING[1] in sevile, just ANA_FLOODING.
And when ANA_FLOODING_IPMC is overwritten with a bogus value, the effect
is that ANA_FLOODING_IPMC gets the value of 0x0003CF7D:
MC6_DATA = 61,
MC6_CTRL = 61,
MC4_DATA = 60,
MC4_CTRL = 0.
Because MC4_CTRL is zero, this means that IPv4 multicast control packets
are not flooded, but dropped. An invalid configuration, and this is how
the issue was actually spotted.
Reported-by: Eldar Gasanov <eldargasanov2@gmail.com>
Reported-by: Maxim Kochetkov <fido_max@inbox.ru>
Tested-by: Eldar Gasanov <eldargasanov2@gmail.com>
Fixes: 84705fc16552 ("net: dsa: felix: introduce support for Seville VSC9953 switch")
Fixes: 3c7b51bd39b2 ("net: dsa: felix: allow flooding for all traffic classes")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201204175416.1445937-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Correct typo in a stub of devm_tegra_memory_controller_get() to fix a
non-ARM kernel compile-testing.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20201111011456.7875-2-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Add common SoC-agnostic ICC framework which turns Tegra Memory Controller
into a memory interconnection provider. This allows us to use interconnect
API for tuning of memory configurations.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Link: https://lore.kernel.org/r/20201104164923.21238-33-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Multiple Tegra drivers need to retrieve Memory Controller and there is
duplication of the retrieval code among the drivers.
Add new devm_tegra_memory_controller_get() helper to remove the code's
duplication and to fix put_device() which was missed in the duplicated
code. Make EMC drivers to use the new helper.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20201104164923.21238-29-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Drivers that use tegra_sku_info and have COMPILE_TEST are failing to be
build due to the missing stub for tegra_sku_info.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20201104164923.21238-4-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
dpaa_eth_napi_schedule() and caam_qi_napi_schedule() schedule NAPI if
invoked from:
- Hard interrupt context
- Any context which is not serving soft interrupts
Any context which is not serving soft interrupts includes hard interrupts
so the in_irq() check is redundant. caam_qi_napi_schedule() has a comment
about this:
/*
* In case of threaded ISR, for RT kernels in_irq() does not return
* appropriate value, so use in_serving_softirq to distinguish between
* softirq and irq contexts.
*/
if (in_irq() || !in_serving_softirq())
This has nothing to do with RT. Even on a non RT kernel force threaded
interrupts run obviously in thread context and therefore in_irq() returns
false when invoked from the handler.
The extension of the in_irq() check with !in_serving_softirq() was there
when the drivers were added, but in the out of tree FSL BSP the original
condition was in_irq() which got extended due to failures on RT.
The usage of in_xxx() in drivers is phased out and Linus clearly requested
that code which changes behaviour depending on context should either be
separated or the context be conveyed in an argument passed by the caller,
which usually knows the context. Right he is, the above construct is
clearly showing why.
The following callchains have been analyzed to end up in
dpaa_eth_napi_schedule():
qman_p_poll_dqrr()
__poll_portal_fast()
fq->cb.dqrr()
dpaa_eth_napi_schedule()
portal_isr()
__poll_portal_fast()
fq->cb.dqrr()
dpaa_eth_napi_schedule()
Both need to schedule NAPI.
The crypto part has another code path leading up to this:
kill_fq()
empty_retired_fq()
qman_p_poll_dqrr()
__poll_portal_fast()
fq->cb.dqrr()
dpaa_eth_napi_schedule()
kill_fq() is called from task context and ends up scheduling NAPI, but
that's pointless and an unintended side effect of the !in_serving_softirq()
check.
The code path:
caam_qi_poll() -> qman_p_poll_dqrr()
is invoked from NAPI and I *assume* from crypto's NAPI device and not
from qbman's NAPI device. I *guess* it is okay to skip scheduling NAPI
(because this is what happens now) but could be changed if it is wrong
due to `budget' handling.
Add an argument to __poll_portal_fast() which is true if NAPI needs to be
scheduled. This requires propagating the value to the caller including
`qman_cb_dqrr' typedef which is used by the dpaa and the crypto driver.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Aymen Sghaier <aymen.sghaier@nxp.com>
Cc: Herbert XS <herbert@gondor.apana.org.au>
Cc: Li Yang <leoyang.li@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Tested-by: Camelia Groza <camelia.groza@nxp.com>
|
|
Put the preparation phase of switchdev VLAN objects to some good use,
and move the check we already had, for preventing the existence of more
than one egress-untagged VLAN per port, to the preparation phase of the
addition.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently we are checking in some places whether the port has a native
VLAN on egress or not, by comparing the ocelot_port->vid value with zero.
That works, because VID 0 can never be a native VLAN configured by the
bridge, but now we want to make similar checks for the pvid. That won't
work, because there are cases when we do have the pvid set to 0 (not by
the bridge, by ourselves, but still.. it's confusing). And we can't
encode a negative value into an u16, so add a bool to the structure.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This is a mechanical patch only.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is one main difference in mscc_ocelot between IP multicast and L2
multicast. With IP multicast, destination ports are encoded into the
upper bytes of the multicast MAC address. Example: to deliver the
address 01:00:5E:11:22:33 to ports 3, 8, and 9, one would need to
program the address of 00:03:08:11:22:33 into hardware. Whereas for L2
multicast, the MAC table entry points to a Port Group ID (PGID), and
that PGID contains the port mask that the packet will be forwarded to.
As to why it is this way, no clue. My guess is that not all port
combinations can be supported simultaneously with the limited number of
PGIDs, and this was somehow an issue for IP multicast but not for L2
multicast. Anyway.
Prior to this change, the raw L2 multicast code was bogus, due to the
fact that there wasn't really any way to test it using the bridge code.
There were 2 issues:
- A multicast PGID was allocated for each MDB entry, but it wasn't in
fact programmed to hardware. It was dummy.
- In fact we don't want to reserve a multicast PGID for every single MDB
entry. That would be odd because we can only have ~60 PGIDs, but
thousands of MDB entries. So instead, we want to reserve a multicast
PGID for every single port combination for multicast traffic. And
since we can have 2 (or more) MDB entries delivered to the same port
group (and therefore PGID), we need to reference-count the PGIDs.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms. A bulk of this is smaller fixes
or cleanups, but some of the new material this time around is:
- Support for Nvidia Tegra234 SoC
- Ring accelerator support for TI AM65x
- PRUSS driver for TI platforms
- Renesas support for R-Car V3U SoC
- Reset support for Cortex-M4 processor on i.MX8MQ
There are also new socinfo entries for a handful of different SoCs and
platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (131 commits)
drm/mediatek: reduce clear event
soc: mediatek: cmdq: add clear option in cmdq_pkt_wfe api
soc: mediatek: cmdq: add jump function
soc: mediatek: cmdq: add write_s_mask value function
soc: mediatek: cmdq: add write_s value function
soc: mediatek: cmdq: add read_s function
soc: mediatek: cmdq: add write_s_mask function
soc: mediatek: cmdq: add write_s function
soc: mediatek: cmdq: add address shift in jump
soc: mediatek: mtk-infracfg: Fix kerneldoc
soc: amlogic: pm-domains: use always-on flag
reset: sti: reset-syscfg: fix struct description warnings
reset: imx7: add the cm4 reset for i.MX8MQ
dt-bindings: reset: imx8mq: add m4 reset
reset: Fix and extend kerneldoc
reset: reset-zynqmp: Added support for Versal platform
dt-bindings: reset: Updated binding for Versal reset driver
reset: imx7: Support module build
soc: fsl: qe: Remove unnessesary check in ucc_set_tdm_rxtx_clk
soc: fsl: qman: convert to use be32_add_cpu()
...
|
|
Pull networking updates from Jakub Kicinski:
- Add redirect_neigh() BPF packet redirect helper, allowing to limit
stack traversal in common container configs and improving TCP
back-pressure.
Daniel reports ~10Gbps => ~15Gbps single stream TCP performance gain.
- Expand netlink policy support and improve policy export to user
space. (Ge)netlink core performs request validation according to
declared policies. Expand the expressiveness of those policies
(min/max length and bitmasks). Allow dumping policies for particular
commands. This is used for feature discovery by user space (instead
of kernel version parsing or trial and error).
- Support IGMPv3/MLDv2 multicast listener discovery protocols in
bridge.
- Allow more than 255 IPv4 multicast interfaces.
- Add support for Type of Service (ToS) reflection in SYN/SYN-ACK
packets of TCPv6.
- In Multi-patch TCP (MPTCP) support concurrent transmission of data on
multiple subflows in a load balancing scenario. Enhance advertising
addresses via the RM_ADDR/ADD_ADDR options.
- Support SMC-Dv2 version of SMC, which enables multi-subnet
deployments.
- Allow more calls to same peer in RxRPC.
- Support two new Controller Area Network (CAN) protocols - CAN-FD and
ISO 15765-2:2016.
- Add xfrm/IPsec compat layer, solving the 32bit user space on 64bit
kernel problem.
- Add TC actions for implementing MPLS L2 VPNs.
- Improve nexthop code - e.g. handle various corner cases when nexthop
objects are removed from groups better, skip unnecessary
notifications and make it easier to offload nexthops into HW by
converting to a blocking notifier.
- Support adding and consuming TCP header options by BPF programs,
opening the doors for easy experimental and deployment-specific TCP
option use.
- Reorganize TCP congestion control (CC) initialization to simplify
life of TCP CC implemented in BPF.
- Add support for shipping BPF programs with the kernel and loading
them early on boot via the User Mode Driver mechanism, hence reusing
all the user space infra we have.
- Support sleepable BPF programs, initially targeting LSM and tracing.
- Add bpf_d_path() helper for returning full path for given 'struct
path'.
- Make bpf_tail_call compatible with bpf-to-bpf calls.
- Allow BPF programs to call map_update_elem on sockmaps.
- Add BPF Type Format (BTF) support for type and enum discovery, as
well as support for using BTF within the kernel itself (current use
is for pretty printing structures).
- Support listing and getting information about bpf_links via the bpf
syscall.
- Enhance kernel interfaces around NIC firmware update. Allow
specifying overwrite mask to control if settings etc. are reset
during update; report expected max time operation may take to users;
support firmware activation without machine reboot incl. limits of
how much impact reset may have (e.g. dropping link or not).
- Extend ethtool configuration interface to report IEEE-standard
counters, to limit the need for per-vendor logic in user space.
- Adopt or extend devlink use for debug, monitoring, fw update in many
drivers (dsa loop, ice, ionic, sja1105, qed, mlxsw, mv88e6xxx,
dpaa2-eth).
- In mlxsw expose critical and emergency SFP module temperature alarms.
Refactor port buffer handling to make the defaults more suitable and
support setting these values explicitly via the DCBNL interface.
- Add XDP support for Intel's igb driver.
- Support offloading TC flower classification and filtering rules to
mscc_ocelot switches.
- Add PTP support for Marvell Octeontx2 and PP2.2 hardware, as well as
fixed interval period pulse generator and one-step timestamping in
dpaa-eth.
- Add support for various auth offloads in WiFi APs, e.g. SAE (WPA3)
offload.
- Add Lynx PHY/PCS MDIO module, and convert various drivers which have
this HW to use it. Convert mvpp2 to split PCS.
- Support Marvell Prestera 98DX3255 24-port switch ASICs, as well as
7-port Mediatek MT7531 IP.
- Add initial support for QCA6390 and IPQ6018 in ath11k WiFi driver,
and wcn3680 support in wcn36xx.
- Improve performance for packets which don't require much offloads on
recent Mellanox NICs by 20% by making multiple packets share a
descriptor entry.
- Move chelsio inline crypto drivers (for TLS and IPsec) from the
crypto subtree to drivers/net. Move MDIO drivers out of the phy
directory.
- Clean up a lot of W=1 warnings, reportedly the actively developed
subsections of networking drivers should now build W=1 warning free.
- Make sure drivers don't use in_interrupt() to dynamically adapt their
code. Convert tasklets to use new tasklet_setup API (sadly this
conversion is not yet complete).
* tag 'net-next-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2583 commits)
Revert "bpfilter: Fix build error with CONFIG_BPFILTER_UMH"
net, sockmap: Don't call bpf_prog_put() on NULL pointer
bpf, selftest: Fix flaky tcp_hdr_options test when adding addr to lo
bpf, sockmap: Add locking annotations to iterator
netfilter: nftables: allow re-computing sctp CRC-32C in 'payload' statements
net: fix pos incrementment in ipv6_route_seq_next
net/smc: fix invalid return code in smcd_new_buf_create()
net/smc: fix valid DMBE buffer sizes
net/smc: fix use-after-free of delayed events
bpfilter: Fix build error with CONFIG_BPFILTER_UMH
cxgb4/ch_ipsec: Replace the module name to ch_ipsec from chcr
net: sched: Fix suspicious RCU usage while accessing tcf_tunnel_info
bpf: Fix register equivalence tracking.
rxrpc: Fix loss of final ack on shutdown
rxrpc: Fix bundle counting for exclusive connections
netfilter: restore NF_INET_NUMHOOKS
ibmveth: Identify ingress large send packets.
ibmveth: Switch order of ibmveth_helper calls.
cxgb4: handle 4-tuple PEDIT to NAT mode translation
selftests: Add VRF route leaking tests
...
|
|
Pull USB/PHY/Thunderbolt driver updates from Greg KH:
"Here is the big set of USB, PHY, and Thunderbolt driver updates for
5.10-rc1.
Lots of tiny different things for these subsystems are in here,
including:
- phy driver updates
- thunderbolt / USB 4 updates and additions
- USB gadget driver updates
- xhci fixes and updates
- typec driver additions and updates
- api conversions to various drivers for core kernel api changes
- new USB control message functions to make it harder to get wrong,
as found by syzbot (took 2 tries to get it right)
- lots of tiny USB driver fixes and updates all over the place
All of these have been in linux-next for a while, with the exception
of the last "obviously correct" patch that updated a FALLTHROUGH
comment that got merged last weekend"
* tag 'usb-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (374 commits)
usb: musb: gadget: Use fallthrough pseudo-keyword
usb: typec: Add QCOM PMIC typec detection driver
USB: serial: option: add Cellient MPL200 card
usb: typec: tcpci_maxim: Add support for Sink FRS
usb: typec: tcpci: Implement callbacks for FRS
usb: typec: tcpm: Add support for Sink Fast Role SWAP(FRS)
usb: typec: tcpci_maxim: Chip level TCPC driver
usb: typec: tcpci: Add set_vbus tcpci callback
usb: typec: tcpci: Add a getter method to retrieve tcpm_port reference
usbip: vhci_hcd: fix calling usb_hcd_giveback_urb() with irqs enabled
usb: cdc-acm: add quirk to blacklist ETAS ES58X devices
USB: serial: ftdi_sio: use cur_altsetting for consistency
USB: serial: option: Add Telit FT980-KS composition
USB: core: remove polling for /sys/kernel/debug/usb/devices
usb: typec: add support for STUSB160x Type-C controller family
usb: typec: add typec_find_pwr_opmode
usb: typec: hd3ss3220: Use OF graph API to get the connector fwnode
dt-bindings: usb: renesas,usb3-peri: Document HS and SS data bus
dt-bindings: usb: convert ti,hd3ss3220 bindings to json-schema
usb: dwc2: Fix INTR OUT transfers in DDMA mode.
...
|
|
Rejecting non-native endian BTF overlapped with the addition
of support for it.
The rest were more simple overlapping changes, except the
renesas ravb binding update, which had to follow a file
move as well as a YAML conversion.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A driver may refuse to enable VLAN filtering for any reason beyond what
the DSA framework cares about, such as:
- having tc-flower rules that rely on the switch being VLAN-aware
- the particular switch does not support VLAN, even if the driver does
(the DSA framework just checks for the presence of the .port_vlan_add
and .port_vlan_del pointers)
- simply not supporting this configuration to be toggled at runtime
Currently, when a driver rejects a configuration it cannot support, it
does this from the commit phase, which triggers various warnings in
switchdev.
So propagate the prepare phase to drivers, to give them the ability to
refuse invalid configurations cleanly and avoid the warnings.
Since we need to modify all function prototypes and check for the
prepare phase from within the drivers, take that opportunity and move
the existing driver restrictions within the prepare phase where that is
possible and easy.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Landen Chao <Landen.Chao@mediatek.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Jonathan McDowell <noodles@earth.li>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need the USB fixes in here as well for testing.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
NXP/FSL SoC driver updates for v5.10
Fix various compile warnings and static analysis warnings for:
- QBMan driver
- DPIO driver
- QE driver
* tag 'soc-fsl-next-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux:
soc: fsl: qe: Remove unnessesary check in ucc_set_tdm_rxtx_clk
soc: fsl: qman: convert to use be32_add_cpu()
soc: fsl: dpio: remove set but not used 'addr_cena'
soc: fsl: qbman: Fix return value on success
soc: fsl: qman: fix -Wpacked-not-aligned warnings
Link: https://lore.kernel.org/r/20200923224416.25788-1-leoyang.li@nxp.com
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
For Ocelot switches, there are 2 ingress pipelines for flow offload
rules: VCAP IS1 (Ingress Classification) and IS2 (Security Enforcement).
IS1 and IS2 support different sets of actions. The pipeline order for a
packet on ingress is:
Basic classification -> VCAP IS1 -> VCAP IS2
Furthermore, IS1 is looked up 3 times, and IS2 is looked up twice (each
TCAM entry can be configured to match only on the first lookup, or only
on the second, or on both etc).
Because the TCAMs are completely independent in hardware, and because of
the fixed pipeline, we actually have very limited options when it comes
to offloading complex rules to them while still maintaining the same
semantics with the software data path.
This patch maps flow offload rules to ingress TCAMs according to a
predefined chain index number. There is going to be a script in
selftests that clarifies the usage model.
There is also an egress TCAM (VCAP ES0, the Egress Rewriter), which is
modeled on top of the default chain 0 of the egress qdisc, because it
doesn't have multiple lookups.
Suggested-by: Allan W. Nielsen <allan.nielsen@microchip.com>
Co-developed-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the mscc_ocelot_switch_lib is common between a pure switchdev and
a DSA driver, the procedure of retrieving a net_device for a certain
port index differs, as those are registered by their individual
front-ends.
Up to now that has been dealt with by always passing the port index to
the switch library, but now, we're going to need to work with net_device
pointers from the tc-flower offload, for things like indev, or mirred.
It is not desirable to refactor that, so let's make sure that the flower
offload core has the ability to translate between a net_device and a
port index properly.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The numbers in struct vcap_props are not intuitive to derive, because
they are not a straightforward copy-and-paste from the reference manual
but instead rely on a fairly detailed level of understanding of the
layout of an entry in the TCAM and in the action RAM. For this reason,
bugs are very easy to introduce here.
Ease the work of hardware porters and read from hardware the constants
that were exported for this particular purpose. Note that this implies
that struct vcap_props can no longer be const.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As a preparation step for the offloading to ES0, let's create the
infrastructure for talking with this hardware block.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As a preparation step for the offloading to IS1, let's create the
infrastructure for talking with this hardware block.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the Ocelot switches there are 3 TCAMs: VCAP ES0, IS1 and IS2, which
have the same configuration interface, but different sets of keys and
actions. The driver currently only supports VCAP IS2.
In preparation of VCAP IS1 and ES0 support, the existing code must be
generalized to work with any VCAP.
In that direction, we should move the structures that depend upon VCAP
instantiation, like vcap_is2_keys and vcap_is2_actions, out of struct
ocelot and into struct vcap_props .keys and .actions, a structure that
is replicated 3 times, once per VCAP. We'll pass that structure as an
argument to each function that does the key and action packing - only
the control logic needs to distinguish between ocelot->vcap[VCAP_IS2]
or IS1 or ES0.
Another change is to make use of the newly introduced ocelot_target_read
and ocelot_target_write API, since the 3 VCAPs have the same registers
but put at different addresses.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are some targets (register blocks) in the Ocelot switch that are
instantiated more than once. For example, the VCAP IS1, IS2 and ES0
blocks all share the same register layout for interacting with the cache
for the TCAM and the action RAM.
For the VCAPs, the procedure for servicing them is actually common. We
just need an API specifying which VCAP we are talking to, and we do that
via these raw ocelot_target_read and ocelot_target_write accessors.
In plain ocelot_read, the target is encoded into the register enum
itself:
u16 target = reg >> TARGET_OFFSET;
For the VCAPs, the registers are currently defined like this:
enum ocelot_reg {
[...]
S2_CORE_UPDATE_CTRL = S2 << TARGET_OFFSET,
S2_CORE_MV_CFG,
S2_CACHE_ENTRY_DAT,
S2_CACHE_MASK_DAT,
S2_CACHE_ACTION_DAT,
S2_CACHE_CNT_DAT,
S2_CACHE_TG_DAT,
[...]
};
which is precisely what we want to avoid, because we'd have to duplicate
the same register map for S1 and for S0, and then figure out how to pass
VCAP instance-specific registers to the ocelot_read calls (basically
another lookup table that undoes the effect of shifting with
TARGET_OFFSET).
So for some targets, propose a more raw API, similar to what is
currently done with ocelot_port_readl and ocelot_port_writel. Those
targets can only be accessed with ocelot_target_{read,write} and not
with ocelot_{read,write} after the conversion, which is fine.
The VCAP registers are not actually modified to use this new API as of
this patch. They will be modified in the next one.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are 2 goals that we follow:
- Reduce the header size
- Make the header size equal between RX and TX
The issue that required long prefix on RX was the fact that the ocelot
DSA tag, being put before Ethernet as it is, would overlap with the area
that a DSA master uses for RX filtering (destination MAC address
mainly).
Now that we can ask DSA to put the master in promiscuous mode, in theory
we could remove the prefix altogether and call it a day, but it looks
like we can't. Using no prefix on ingress, some packets (such as ICMP)
would be received, while others (such as PTP) would not be received.
This is because the DSA master we use (enetc) triggers parse errors
("MAC rx frame errors") presumably because it sees Ethernet frames with
a bad length. And indeed, when using no prefix, the EtherType (bytes
12-13 of the frame, bits 96-111) falls over the REW_VAL field from the
extraction header, aka the PTP timestamp.
When turning the short (32-bit) prefix on, the EtherType overlaps with
bits 64-79 of the extraction header, which are a reserved area
transmitted as zero by the switch. The packets are not dropped by the
DSA master with a short prefix. Actually, the frames look like this in
tcpdump (below is a PTP frame, with an extra dsa_8021q tag - dadb 0482 -
added by a downstream sja1105).
89:0c:a9:f2:01:00 > 88:80:00:0a:00:1d, 802.3, length 0: LLC, \
dsap Unknown (0x10) Individual, ssap ProWay NM (0x0e) Response, \
ctrl 0x0004: Information, send seq 2, rcv seq 0, \
Flags [Response], length 78
0x0000: 8880 000a 001d 890c a9f2 0100 0000 100f ................
0x0010: 0400 0000 0180 c200 000e 001f 7b63 0248 ............{c.H
0x0020: dadb 0482 88f7 1202 0036 0000 0000 0000 .........6......
0x0030: 0000 0000 0000 0000 0000 001f 7bff fe63 ............{..c
0x0040: 0248 0001 1f81 0500 0000 0000 0000 0000 .H..............
0x0050: 0000 0000 0000 0000 0000 0000 ............
So the short prefix is our new default: we've shortened our RX frames by
12 octets, increased TX by 4, and headers are now equal between RX and
TX. Note that we still need promiscuous mode for the DSA master to not
drop it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the ocelot_configure_cpu() function, which was in fact bringing
up 2 ports: the CPU port module, which both switchdev and DSA have, and
the NPI port, which only DSA has.
The (non-Ethernet) CPU port module is at a fixed index in the analyzer,
whereas the NPI port is selected through the "ethernet" property in the
device tree.
Therefore, the function to set up an NPI port is DSA-specific, so we
move it there, simplifying the ocelot switch library a little bit.
Cc: Horatiu Vultur <horatiu.vultur@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: UNGLinuxDriver <UNGLinuxDriver@microchip.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
INIT_IPS and GATE_ENABLE fields have a wrong offset in SG_CONFIG_REG_3.
This register is used by stream gate control of PSFP, and it has not
been used before, because PSFP is not implemented in ocelot driver.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, ocelot switchdev passes the skb directly to the function that
enqueues it to the list of skb's awaiting a TX timestamp. Whereas the
felix DSA driver first clones the skb, then passes the clone to this
queue.
This matters because in the case of felix, the common IRQ handler, which
is ocelot_get_txtstamp(), currently clones the clone, and frees the
original clone. This is useless and can be simplified by using
skb_complete_tx_timestamp() instead of skb_tstamp_tx().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This fixes compile warnings from the -Wpacked-not-aligned option.
In file included from ../drivers/crypto/caam/qi.c:12:
../include/soc/fsl/qman.h:259:1: warning: alignment 1 of ‘struct qm_dqrr_entry’ is less than 8 [-Wpacked-not-aligned]
} __packed;
^
../include/soc/fsl/qman.h:292:2: warning: alignment 1 of ‘struct <anonymous>’ is less than 8 [-Wpacked-not-aligned]
} __packed ern;
^
Reported-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
|
|
Pull networking fixes from Jakub Kicinski:
- fix failure to add bond interfaces to a bridge, the offload-handling
code was too defensive there and recent refactoring unearthed that.
Users complained (Ido)
- fix unnecessarily reflecting ECN bits within TOS values / QoS marking
in TCP ACK and reset packets (Wei)
- fix a deadlock with bpf iterator. Hopefully we're in the clear on
this front now... (Yonghong)
- BPF fix for clobbering r2 in bpf_gen_ld_abs (Daniel)
- fix AQL on mt76 devices with FW rate control and add a couple of AQL
issues in mac80211 code (Felix)
- fix authentication issue with mwifiex (Maximilian)
- WiFi connectivity fix: revert IGTK support in ti/wlcore (Mauro)
- fix exception handling for multipath routes via same device (David
Ahern)
- revert back to a BH spin lock flavor for nsid_lock: there are paths
which do require the BH context protection (Taehee)
- fix interrupt / queue / NAPI handling in the lantiq driver (Hauke)
- fix ife module load deadlock (Cong)
- make an adjustment to netlink reply message type for code added in
this release (the sole change touching uAPI here) (Michal)
- a number of fixes for small NXP and Microchip switches (Vladimir)
[ Pull request acked by David: "you can expect more of this in the
future as I try to delegate more things to Jakub" ]
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (167 commits)
net: mscc: ocelot: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
net: dsa: seville: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
net: dsa: felix: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
inet_diag: validate INET_DIAG_REQ_PROTOCOL attribute
net: bridge: br_vlan_get_pvid_rcu() should dereference the VLAN group under RCU
net: Update MAINTAINERS for MediaTek switch driver
net/mlx5e: mlx5e_fec_in_caps() returns a boolean
net/mlx5e: kTLS, Avoid kzalloc(GFP_KERNEL) under spinlock
net/mlx5e: kTLS, Fix leak on resync error flow
net/mlx5e: kTLS, Add missing dma_unmap in RX resync
net/mlx5e: kTLS, Fix napi sync and possible use-after-free
net/mlx5e: TLS, Do not expose FPGA TLS counter if not supported
net/mlx5e: Fix using wrong stats_grps in mlx5e_update_ndo_stats()
net/mlx5e: Fix multicast counter not up-to-date in "ip -s"
net/mlx5e: Fix endianness when calculating pedit mask first bit
net/mlx5e: Enable adding peer miss rules only if merged eswitch is supported
net/mlx5e: CT: Fix freeing ct_label mapping
net/mlx5e: Fix memory leak of tunnel info when rule under multipath not ready
net/mlx5e: Use synchronize_rcu to sync with NAPI
net/mlx5e: Use RCU to protect rq->xdp_prog
...
|
|
It is a good measure to ensure correctness if the structures that are
meant to remain constant are only processed by functions that thake
constant arguments.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently mscc_ocelot_init_ports() will skip initializing a port when it
doesn't have a phy-handle, so the ocelot->ports[port] pointer will be
NULL. Take this into consideration when tearing down the driver, and add
a new function ocelot_deinit_port() to the switch library, mirror of
ocelot_init_port(), which needs to be called by the driver for all ports
it has initialized.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ocelot_port->ts_id is used to:
(a) populate skb->cb[0] for matching the TX timestamp in the PTP IRQ
with an skb.
(b) populate the REW_OP from the injection header of the ongoing skb.
Only then is ocelot_port->ts_id incremented.
This is a problem because, at least theoretically, another timestampable
skb might use the same ocelot_port->ts_id before that is incremented.
Normally all transmit calls are serialized by the netdev transmit
spinlock, but in this case, ocelot_port_add_txtstamp_skb() is also
called by DSA, which has started declaring the NETIF_F_LLTX feature
since commit 2b86cb829976 ("net: dsa: declare lockless TX feature for
slave ports"). So the logic of using and incrementing the timestamp id
should be atomic per port.
The solution is to use the global ocelot_port->ts_id only while
protected by the associated ocelot_port->ts_id_lock. That's where we
populate skb->cb[0]. Note that for ocelot, ocelot_port_add_txtstamp_skb
is called for the actual skb, but for felix, it is called for the skb's
clone. That is something which will also be changed in the future.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for FUSE block found on the Tegra234 SoC, which is largely
similar to the IP found on previous generations.
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
Vladimir Oltean
Jakub Kicinski
Damien Le Moal
Lina Iyer
Vineet Gupta
Dmitry Osipenko
Linus Torvalds
Sebastian Andrzej Siewior
David S. Miller
Greg Kroah-Hartman
Olof Johansson
Xiaoliang Yang
Li Yang
Thierry Reding