| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch adds the Third Party Copy (3PC) bit to signal support
for EXTENDED_COPY within standard inquiry response data.
Also add emulate_3pc device attribute in configfs (enabled by default)
to allow the exposure of this bit to be disabled, if necessary.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Zach Brown <zab@redhat.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
|
|
This patch adds support for EXTENDED_COPY emulation from SPC-3, that
enables full copy offload target support within both a single virtual
backend device, and across multiple virtual backend devices. It also
functions independent of target fabric, and supports copy offload
across multiple target fabric ports.
This implemenation supports both EXTENDED_COPY PUSH and PULL models
of operation, so the actual CDB may be received on either source or
desination logical unit.
For Target Descriptors, it currently supports the NAA IEEE Registered
Extended designator (type 0xe4), which allows the reference of target
ports to occur independent of fabric type using EVPD 0x83 WWNs.
For Segment Descriptors, it currently supports copy from block to
block (0x02) mode.
It also honors any present SCSI reservations of the destination target
port. Note that only Supports No List Identifier (SNLID=1) mode is
supported.
Also included is basic RECEIVE_COPY_RESULTS with service action type
OPERATING PARAMETERS (0x03) required for SNLID=1 operation.
v3 changes:
- Fix incorrect return type in target_do_receive_copy_results()
(Fengguang)
v2 changes:
- Use target_alloc_sgl() instead of transport_generic_get_mem()
- Convert debug output to use pr_debug()
- Convert target_xcopy_parse_target_descriptors() NAA IEEN WWN
dump to use 0x%16phN format specification
- Drop unnecessary xcopy_pt_cmd->xpt_passthrough_wsem, and
associated usage in xcopy_pt_write_pending() and
target_xcopy_issue_pt_cmd()
- Add check for unsupported EXTENDED_COPY(LID4) service action
bits in target_do_xcopy()
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Zach Brown <zab@redhat.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
|
|
EXTENDED_COPY needs to be able to search a global list of devices
based on NAA WWN device identifiers, so add a simple g_device_list
protected by g_device_mutex.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Zach Brown <zab@redhat.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
|
|
This patch adds support for COMPARE_AND_WRITE emulation on a per block
basis. This logic is used as an atomic test and set primative currently
used by VMWare ESX VAAI for performing array side locking of individual
VMFS extent ownership.
This includes the COMPARE_AND_WRITE CDB parsing within sbc_parse_cdb(),
and does the majority of the work within the compare_and_write_callback()
to perform the verify instance user data comparision, and subsequent
write instance user data I/O submission upon a successfull comparision.
The synchronization is enforced by se_device->caw_sem, that is obtained
before the initial READ I/O submission in sbc_compare_and_write(). The
mutex is then released upon MISCOMPARE in compare_and_write_callback(),
or upon WRITE instance user-data completion in compare_and_write_post().
The implementation currently assumes a single logical block (NoLB=1).
v4 changes:
- Explicitly clear cmd->transport_complete_callback for two failure
cases in sbc_compare_and_write() in order to avoid double unlock
of ->caw_sem in compare_and_write_callback() (Dan Carpenter)
v3 changes:
- Convert se_device->caw_mutex to ->caw_sem
v2 changes:
- Set SCF_COMPARE_AND_WRITE and cmd->execute_cmd() to
sbc_compare_and_write() during setup in sbc_parse_cdb()
- Use sbc_compare_and_write() for initial READ submission with
DMA_FROM_DEVICE
- Reset cmd->execute_cmd() to sbc_execute_rw() for write instance
user-data in compare_and_write_callback()
- Drop SCF_BIDI command flag usage
- Set TRANSPORT_PROCESSING + transport_state flags before write
instance submission, and convert to __target_execute_cmd()
- Prevent sbc_get_size() from being being called twice to
generate incorrect size in sbc_parse_cdb()
- Enforce se_device->caw_mutex synchronization between initial
READ I/O submission, and final WRITE I/O completion.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
|
|
This patch adds the MAXIMUM COMPARE AND WRITE LENGTH bit, currently
hardcoded to a single logical block (NoLB=1) within the Block Limits
VPD in spc_emulate_evpd_b0().
Also add emulate_caw device attribute in configfs (enabled by default)
to allow the exposure of this bit to be disabled, if necessary.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
|
|
After COMPARE_AND_WRITE completes it's comparision, the WRITE
payload SGLs head expect to be updated to point from the verify
instance of user data, to the write instance of user data.
So for this special case, add transport_reset_sgl_orig() usage
within transport_free_pages() and add se_cmd->t_data_[sg,nents]_orig
members to save the original assignments.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
|
|
COMPARE_AND_WRITE expects to be able to send down a DMA_FROM_DEVICE
to obtain the necessary READ payload for comparision against the
first half of the WRITE payload containing the verify user data.
Currently virtual backends expect to internally reference SGLs,
SGL nents, and data_direction, so change IBLOCK, FILEIO and RD
sbc_ops->execute_rw() to accept this values as function parameters.
Also add default sbc_execute_rw() handler for the typical case for
cmd->execute_rw() submission using cmd->t_data_sg, cmd->t_data_nents,
and cmd->data_direction).
v2 Changes:
- Add SCF_COMPARE_AND_WRITE command flag
- Use sbc_execute_rw() for normal cmd->execute_rw() submission
with expected se_cmd members.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
|
|
This patch adds TCM_MISCOMPARE_VERIFY (ASC=0x1d, ASCQ=0x00) sense
handling to transport_send_check_condition_and_sense(), which is
required for a COMPARE_AND_WRITE comparision failure.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
|
|
This patch adds a sense_reason_t return to ->transport_complete_callback(),
and updates target_complete_ok_work() to invoke the call if necessary to
transport_send_check_condition_and_sense() during the failure case.
Also update xdreadwrite_callback() to use this return value.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
|
|
This patch adds lib/idr.c based transport_init_session_tags() logic
that allows fabric drivers to setup a per-cpu se_sess->sess_tag_pool
and associated se_sess->sess_cmd_map for basic tagged pre-allocation
of fabric descriptor sized memory.
v5 changes:
- Convert to percpu_ida.h include
v4 changes:
- Add transport_alloc_session_tags() for fabrics that need early
transport_init_session()
v3 changes:
- Update to percpu-ida usage
Cc: Kent Overstreet <kmo@daterainc.com>
Cc: Asias He <asias@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Asias He <asias@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Three have been checked for but were never set. Remove the dead code.
Also renumbers the remaining ones to a) get rid of the holes after the
removal and b) avoid a collision between TMR_FUNCTION_COMPLETE==0 and
the uninitialized case. If we failed to set a code, we should rather
fall into the default case then return success.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch adds an optional /auth/ configfs group to TPG context that
can be used by fabrics like iscsi-target for TPG demo-mode
authentication.
Cc: Dax Kelson <dkelson@gurulabs.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Now with iscsi-target using modern se_cmd->cmd_kref accounting in
v3.10 code, it's safe to go ahead and drop the legacy release
codepath + se_cmd->check_release bit in transport_release_cmd()
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@kernel.org>
Cc: Kent Overstreet <koverstreet@google.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Moussa Ba <moussaba@micron.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch removes legacy se_cmd->t_fe_count usage in order to avoid
se_cmd->t_state_lock access within transport_put_cmd() during normal
fast path se_cmd descriptor release.
Also drop the left-over parameter usage within core_tmr_handle_tas_abort()
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@kernel.org>
Cc: Kent Overstreet <koverstreet@google.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Moussa Ba <moussaba@micron.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Instead of taking the buffer and length, update_and_write_aptpl() will
allocate the buffer as needed, and then free it. Instead, the function
takes an 'aptpl' boolean parameter.
This enables us to remove memory alloc/frees from struct
t10_pr_registration and other spots.
There is a slight loss of functionality because each callsite doesn't get
its own pr_debug any more, but this info can be cleaned via ftrace if
necessary and I think the shorter code is worth it.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
It's only ever set to PR_APTPL_BUF_LEN, so we don't need a variable.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Switch back to pre commit 1c7b13fe652 list splicing logic for active I/O
shutdown with tcm_qla2xxx + ib_srpt fabrics.
The original commit was done under the incorrect assumption that it's safe to
walk se_sess->sess_cmd_list unprotected in target_wait_for_sess_cmds() after
sess->sess_tearing_down = 1 has been set by target_sess_cmd_list_set_waiting()
during session shutdown.
So instead of adding sess->sess_cmd_lock protection around sess->sess_cmd_list
during target_wait_for_sess_cmds(), switch back to sess->sess_wait_list to
allow wait_for_completion() + TFO->release_cmd() to occur without having to
walk ->sess_cmd_list after the list_splice.
Also add a check to exit if target_sess_cmd_list_set_waiting() has already
been called, and add a WARN_ON to check for any fabric bug where new se_cmds
are added to sess->sess_cmd_list after sess->sess_tearing_down = 1 has already
been set.
Cc: Joern Engel <joern@logfs.org>
Cc: Roland Dreier <roland@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Some were incremented, but never used anywhere from what I could tell.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
SBC-3 (revision 35) says:
The PARAMETER LIST LENGTH field specifies the length in bytes of the
UNMAP parameter list that is available to be transferred from the
Data-Out Buffer. If the parameter list length is greater than zero
and less than 0008h (i.e., eight), then the device server shall
terminate the command with CHECK CONDITION status with the sense key
set to ILLEGAL REQUEST and the additional sense code set to
PARAMETER LIST LENGTH ERROR. A PARAMETER LIST LENGTH set to zero
specifies that no data shall be sent.
so our sense code for too-short descriptors was wrong, and we were
incorrectly failing commands that didn't transfer any descriptors.
While we're at it, also handle the UNMAP check:
If the ANCHOR bit is set to one, and the ANC_SUP bit in the Logical
Block Provisioning VPD page (see 6.6.4) is set to zero, then the
device server shall terminate the command with CHECK CONDITION
status with the sense key set to ILLEGAL REQUEST and the additional
sense code set to INVALID FIELD IN CDB.
(chris boot: Fix wrong cut+paste comment in transport_send_check_condition_and_sense)
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch changes LIO to use the configfs backend device name as the
model if you echo '1' to an individual device's emulate_model_alias attribute.
This is a valid operation only on devices with an export count of 0.
Signed-off-by: Tregaron Bayly <tbayly@bluehost.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
"buf" is 128 characters and "vpd->device_identifier" is 256. It makes
the static checkers complain.
Also bump VPD_TMP_BUF_SIZE to match INQUIRY_VPD_DEVICE_IDENTIFIER_LEN.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Introduce TCM_NO_SENSE, mapping to sense code
'Not ready, no additional sense information'.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Cc: Nicholas Bellinger <nab@risingtidesystems.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Thanks for reviews, looking a lot better.
---- 8< ----
Initiator access config could be easier. The way other storage vendors
have addressed this is to support initiator groups: the admin adds
initiator WWNs to the group, and then LUN permissions can be granted for
the entire group at once.
Instead of changing ktarget's configfs interface, this patch keeps
the configfs interface per-initiator-wwn and just adds a 'tag' field
for each. This should be enough for user tools like targetcli to group
initiator ACLs and sync their configurations.
acl_tag is not used internally, but needs to be kept in configfs so that
all user tools can avoid dependencies on each other.
Code tested to work, although userspace pieces still to be implemented.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch adds [dev,lun]_link_magic value assignment + checks within generic
target_fabric_port_link() and target_fabric_mappedlun_link() code to ensure
destination config_item *target_item sent from configfs_symlink() ->
config_item_operations->allow_link() is the underlying se_device->dev_group
and se_lun->lun_group that we expect to symlink.
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch adds a new max_write_same_len device attribute for use with
WRITE_SAME w/ UNMAP=0 backend emulation. This can be useful for
lowering the default backend value (IBLOCK uses 0xFFFF).
Also, update block limits VPD emulation code in spc_emulate_evpd_b0() to
report MAXIMUM WRITE SAME LENGTH, and enforce max_write_same_len during
sbc_parse() -> sbc_setup_write_same() CDB sanity checking for all emulated
WRITE_SAME w/ UNMAP=0 cases.
(Robert: Move max_write_same_len check in sbc_setup_write_same() to
check both WRITE_SAME w/ UNMAP=1 and w/ UNMAP=0 cases)
Cc: Christoph Hellwig <hch@lst.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Robert Elliott <Elliott@hp.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Pass the sense reason as an explicit return value from the I/O submission
path instead of storing it in struct se_cmd and using negative return
values. This cleans up a lot of the code pathes, and with the sparse
annotations for the new sense_reason_t type allows for much better
error checking.
(nab: Convert spc_emulate_modesense + spc_emulate_modeselect to use
sense_reason_t with Roland's MODE SELECT changes)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
We always support ALUA for virtual backends, and never for physical ones. Simplify
the code to just deal with these two cases and remove the superflous abstractions.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
We do not support host-level reservations for the pscsi backend, and all
virtual backends are newere than SCSI-2, so just make the combined
SPC-3 + SCSI-2 support the only supported variant and kill the switches
for the different implementations, given that this code handles the no-op
version just fine.
(hch: Update DRF_SPC2_RESERVATIONS lock usage)
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
We can just key off ordered tag emulation of the transport_type field.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Simplify the code a lot by killing the superflous struct se_subsystem_dev.
Instead se_device is allocated early on by the backend driver, which allocates
it as part of its own per-device structure, borrowing the scheme that is for
example used for inode allocation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Similar to INQUIRY and MODE SENSE, construct the sense data in a
buffer and later copy it to the scatterlist. Do not do anything,
but still clear a pending unit attention condition, if the allocation
length is zero.
However, SPC tells us that "If a REQUEST SENSE command is terminated with
CHECK CONDITION status [and] the REQUEST SENSE command was received on
an I_T nexus with a pending unit attention condition (i.e., before the
device server reports CHECK CONDITION status), then the device server
shall not clear the pending unit attention condition." Do the
transport_kmap_data_sg early to detect this case.
It also tells us "Device servers shall not adjust the additional sense
length to reflect truncation if the allocation length is less than the
sense data available", so do not do that! Note that the err variable
is write-only.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This was originally for helping fabrics to determine overflow/underflow
status, and has been superceeded by SCF_OVERFLOW_BIT + SCF_UNDERFLOW_BIT.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Many SCSI commands are defined to return a CHECK CONDITION / ILLEGAL
REQUEST with ASC set to LOGICAL BLOCK ADDRESS OUT OF RANGE if the
initiator sends a command that accesses a too-big LBA. Add an enum
value and case entries so that target code can return this status.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Since we set se_session.sess_tearing_down and stop new commands from
being added to se_session.sess_cmd_list before we wait for commands to
finish when freeing a session, there's no need for a separate
sess_wait_list -- if we let new commands be added to sess_cmd_list
after setting sess_tearing_down, that would be a bug that breaks the
logic of waiting in-flight commands.
Also rename target_splice_sess_cmd_list() to
target_sess_cmd_list_set_waiting(), since we are no longer splicing
onto a separate list.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
The last functionality of the target processing thread is offloading possibly
long running task management requests from the submitter context. To keep
TMR semantics the same we need a single threaded ordered queue, which can
be provided by a per-device workqueue with the right flags.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Remove this command submission path which is not used by any in-tree driver.
This also removes the now unused new_cmd_map fabtric method, which a few
drivers implemented despite never calling transport_generic_handle_cdb_map.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Remove the dead SCF_SE_ALLOW_EOO and SCF_DELAYED_CMD_FROM_SAM_ATTR
from se_cmd_flags_table.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Also remove the unused ref_task_lun field in struct se_tmr_req.
(nab: Add missing TASK_REASSIGN ref_lun vs. ref_cmd orig_fe_lun checks
in iscsit_tmr_task_reassign)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Since "target: Drop se_device TCQ queue_depth usage from I/O path" we always
submit all commands (or back then, tasks) from __transport_execute_tasks.
That means the the execute list has lots its purpose, as we can simply
submit the commands that are restarted in transport_complete_task_attr
directly while we walk the list. In fact doing so also solves a race
in the way it currently walks to delayed_cmd_list as well.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
We don't need three flags to classifiy the CDB as we can check for a NULL S/G
list for a dataless command, and can infer from the absence of the data flag
that we deal with a control CDB. Also remove the _SG_IO from the data CDB
flag as all I/O is dont on S/G lists now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch adds support for ALUA MI_REPORT_TARGET_PGS extended header
format defined within SPC-4. It changes target core ALUA emulation logic
within target_emulate_report_target_port_groups() to support both the
extended and original length only header formats.
It includes adding a new 'implict_trans_secs' attribute for each ALUA
target port group to control the value returned to the application client
for an recommended implict translation timeout in seconds. By default
this value is currently set to zero, and limited up to 255 by virtue of
using a single byte in the extended header format.
This value is used by target_emulate_report_target_port_groups() within
the extended header logic to set IMPLICIT TRANSITION TIME as defined by
spc4r30.
Cc: Hannes Reinecke <hare@suse.de>
Cc: Rob Evers <revers@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch removes the original usage of dev_attr->max_sectors in favor of
dev_attr->hw_max_sectors that is now being enforced by target core from
within transport_generic_cmd_sequencer() for SCF_SCSI_DATA_SG_IO_CDB ops.
After the recent se_task removal patches from hch, this value for IBLOCK
backends being set via configfs by userspace from an saved max_sectors
value that is turning out to be problematic, so it makes sense to go ahead
and remove this now legacy attribute all-together.
This patch also continues to make se_dev_set_default_attribs() do
(sectors / block_size) alignment for what actually get used by
target_core_mod to be safe here, following the same alignment currently
used by fabric_max_sectors.
Reported-by: Andy Grover <agrover@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Now that tasks are gone we are guaranteed to only get a single completion
per command, and thus don't need this counter.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Now that tasks are gone we are guaranteed to only get a single completion
per command, and thus don't need this counter.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Now that tasks are gone we are guaranteed to only get a single completion
per command, and thus don't need this counter.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
We can use struct se_cmd for everything it did. Make sure to pass the S/G
list and data direction to the execution function to ease adding back BIDI
support later on.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
Nicholas Bellinger
Nicholas Bellinger
Joern Engel
Andy Grover
Roland Dreier
Tregaron Bayly
Dan Carpenter
Hannes Reinecke
Christoph Hellwig
Christoph Hellwig
Paolo Bonzini