| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Non default Drive Strength cannot be set automatically. It is a function
of the board design and only if there is a specific platform handler can
it be set. The platform handler needs to take into account the board
design. Pass to the platform code the necessary information.
For example: The card and host controller may indicate they support HIGH
and LOW drive strength. There is no way to know what should be chosen
without specific board knowledge. Setting HIGH may lead to reflections
and setting LOW may not suffice. There is no mechanism (like ethernet
duplex or speed pulses) to determine what should be done automatically.
If no platform handler is defined -- use the default value.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Reviewed-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Previously there has only been one function mmc_wait_for_req()
to start and wait for a request. This patch adds:
* mmc_start_req() - starts a request wihtout waiting
If there is on ongoing request wait for completion
of that request and start the new one and return.
Does not wait for the new command to complete.
This patch also adds new function members in struct mmc_host_ops
only called from core.c:
* pre_req - asks the host driver to prepare for the next job
* post_req - asks the host driver to clean up after a completed job
The intention is to use pre_req() and post_req() to do cache maintenance
while a request is active. pre_req() can be called while a request is
active to minimize latency to start next job. post_req() can be used after
the next job is started to clean up the request. This will minimize the
host driver request end latency. post_req() is typically used before
ending the block request and handing over the buffer to the block layer.
Add a host-private member in mmc_data to be used by pre_req to mark the
data. The host driver will then check this mark to see if the data is
prepared or not.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Venkatraman S <svenkatr@ti.com>
Tested-by: Sourav Poddar <sourav.poddar@ti.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
There are several situations when dw_mci_submit_data_dma() decides to
fall back to PIO mode instead of using DMA, due to a short (to avoid
overhead) or "complex" (e.g. with unaligned buffers) transaction, even
though host->use_dma is set. However dw_mci_stop_dma() decides whether
to stop DMA or set the EVENT_XFER_COMPLETE event based on host->use_dma.
When falling back to PIO mode this results in data timeout errors
getting missed and the driver locking up.
Therefore add host->using_dma to indicate whether the current
transaction is using dma or not, and adjust dw_mci_stop_dma() to use
that instead.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Some host controllers will not operate without a hardware
timeout that is limited in value. However large discards
require large timeouts, so there needs to be a way to
specify the maximum discard size.
A host controller driver may now specify the maximum discard
timeout possible so that max_discard_sectors can be calculated.
However, for eMMC when the High Capacity Erase Group Size
is not in use, the timeout calculation depends on clock
rate which may change. For that case Preferred Erase Size
is used instead.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Update functions for PIO pushing and pulling data to and from the FIFO
so that they can handle unaligned output buffers and unaligned buffer
lengths. This makes more of the tests in mmc_test pass.
Unaligned lengths in pulls are handled by reading the full FIFO item,
and storing the remaining bytes in a small internal buffer (part_buf).
The next data pull will copy data out of this buffer first before
accessing the FIFO again. Similarly, for pushes the final bytes that
don't fill a FIFO item are stored in the part_buf (or sent anyway if
it's the last transfer), and then the part_buf is included at the
beginning of the next buffer pushed.
Unaligned buffers in pulls are handled specially if the architecture
cannot do efficient unaligned accesses, by reading FIFO items into a
aligned local buffer, and memcpy'ing them into the output buffer, again
storing any remaining bytes in the internal buffer. Similarly for pushes
the buffer is memcpy'd into an aligned local buffer then written to the
FIFO.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The FIFO_DEPTH hardware configuration parameter can be found from the
power-on value of RX_WMark in the FIFOTH register. This is used to
initialise the watermarks, but when calculating the number of free fifo
spaces a preprocessor definition is used which is hard coded to 32.
Fix reading the value out of FIFOTH (the default value in the RX_WMark
field is FIFO_DEPTH-1 not FIFO_DEPTH). Allow the fifo depth to be
overriden by platform data (since a bootloader may have changed FIFOTH
making auto-detection unreliable). Store the fifo_depth for later use.
Also fix the calculation to find the number of free bytes in the fifo to
include the fifo depth in the left shift by the data shift, since the
fifo depth is measured in fifo items not bytes.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Convert the card insert/remove tasklet to a workqueue, and call the
setpower platform specific callback without the spinlock held. This
means neither of the setpower or get_cd callbacks are called from atomic
context which allows them to sleep.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Some controllers require waiting for the bus to become idle
before writing to some registers. I have implemented this
by adding a hook to sd_ctrl_write16() and implementing
a hook for SDHI which waits for the bus to become idle.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
This reflects at least the current usage of this register
and I think it improves the readability of the code ever so slightly.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
If the MMC_SEND_STATUS command is not successful, we should not return
a zero status word, but instead allow the caller to know positively
that an error occurred.
Convert the open-coded get_card_status() to use the helper function,
and provide definitions for the card state field.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
As suggested by Arnd, move platform data to include/linux/platform_data
in order to improve build coverage for the driver.
Signed-off-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Standardize the checks for multiple MMC header file inclusion,
including adding comments to terminating #endif's, and fixing
one incorrect comment.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The structure sdhci_pltfm_data is not necessarily to be in a public
header like include/linux/mmc/sdhci-pltfm.h, so the patch moves it
into drivers/mmc/host/sdhci-pltfm.h and eliminates the former one.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The patch turns the common stuff in sdhci-pltfm.c into functions, and
add device drivers their own .probe and .remove which in turn call
into the common functions, so that those sdhci-pltfm device drivers
register itself and keep all device specific things away from common
sdhci-pltfm file.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
`make headers_check` complains that
linux-2.6/usr/include/linux/sdla.h:116: userspace cannot reference
function or variable defined in the kernel
this is due to that there is no such a kernel function,
void sdla(void *cfg_info, char *dev, struct frad_conf *conf, int quiet);
I don't know why we have it in a kernel header, so remove it.
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
Bluetooth: Fix crash with incoming L2CAP connections
Bluetooth: Fix regression in L2CAP connection procedure
gianfar: rx parser
r6040: only disable RX interrupt if napi_schedule_prep is successful
net: remove NETIF_F_ALL_TX_OFFLOADS
net: sctp: fix checksum marking for outgoing packets
|
|
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: Fixes device power states array overflow
ACPI, APEI, HEST, Detect duplicated hardware error source ID
ACPI: Fix lockdep false positives in acpi_power_off()
|
|
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
There is no software fallback implemented for SCTP or FCoE checksumming,
and so it should not be passed on by software devices like bridge or bonding.
For VLAN devices, this is different. First, the driver for underlying device
should be prepared to get offloaded packets even when the feature is disabled
(especially if it advertises it in vlan_features). Second, devices under
VLANs do not get replaced without tearing down the VLAN first.
This fixes a mess I accidentally introduced while converting bonding to
ndo_fix_features.
NETIF_F_SOFT_FEATURES are removed from BOND_VLAN_FEATURES because they
are unused as of commit 712ae51afd.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
Commit 28c2103 added new state ACPI_STATE_D3_COLD, so the device power
states array must be expanded by one also.
v2: Use ACPI_D_STATE_COUNT instead of number 5 for the array size.
Reported-by: Dan Carpenter <error27@gmail.com>
Suggested-by: Oldřich Jedlička <oldium.pro@seznam.cz>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
mmc: core: Bus width testing needs to handle suspend/resume
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits)
slip: fix wrong SLIP6 ifdef-endif placing
natsemi: fix another dma-debug report
sctp: ABORT if receive, reassmbly, or reodering queue is not empty while closing socket
net: Fix default in docs for tcp_orphan_retries.
hso: fix a use after free condition
net/natsemi: Fix module parameter permissions
XFRM: Fix memory leak in xfrm_state_update
sctp: Enforce retransmission limit during shutdown
mac80211: fix TKIP replay vulnerability
mac80211: fix ie memory allocation for scheduled scans
ssb: fix init regression of hostmode PCI core
rtlwifi: rtl8192cu: Add new USB ID for Netgear WNA1000M
ath9k: Fix tx throughput drops for AR9003 chips with AES encryption
carl9170: add NEC WL300NU-AG usbid
cfg80211: fix deadlock with rfkill/sched_scan by adding new mutex
ath5k: fix incorrect use of drvdata in PCI suspend/resume code
ath5k: fix incorrect use of drvdata in sysfs code
Bluetooth: Fix memory leak under page timeouts
Bluetooth: Fix regression with incoming L2CAP connections
Bluetooth: Fix hidp disconnect deadlocks and lost wakeup
...
|
|
On reading the ext_csd for the first time (in 1 bit mode), save the
ext_csd information needed for bus width compare.
On every pass we make re-reading the ext_csd, compare the data
against the saved ext_csd data.
This fixes a regression introduced in 3.0-rc1 by 08ee80cc397ac1a3
("mmc: core: eMMC bus width may not work on all platforms"), which
incorrectly assumed we would be re-reading the ext_csd at resume-
time.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
All ACPICA locks are allocated by the same function,
acpi_os_create_lock(), with the help of a local variable called
"lock". Thus, when lockdep is enabled, it uses "lock" as the
name of all those locks and regards them as instances of the same
lock, which causes it to report possible locking problems with them
when there aren't any.
To work around this problem, define acpi_os_create_lock() as a macro
and make it pass its argument to spin_lock_init(), so that lockdep
uses it as the name of the new lock. Define this macron in a
Linux-specific file, to minimize the resulting modifications of
the OS-independent ACPICA parts.
This change is based on an earlier patch from Andrea Righi and it
addresses a regression from 2.6.39 tracked as
https://bugzilla.kernel.org/show_bug.cgi?id=38152
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-and-tested-by: Borislav Petkov <bp@alien8.de>
Tested-by: Andrea Righi <andrea@betterlinux.com>
Reviewed-by: Florian Mickler <florian@mickler.org>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/mm: Fix memory_block_size_bytes() for non-pseries
mm: Move definition of MIN_MEMORY_BLOCK_SIZE to a header
|
|
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
pcmcia: pxa2xx/vpac270: free gpios on exist rather than requesting
ARM: pxa/raumfeld: fix device name for codec ak4104
ARM: pxa/raumfeld: display initialisation fixes
ARM: pxa/raumfeld: adapt to upcoming hardware change
ARM: pxa: fix gpio_to_chip() clash with gpiolib namespace
genirq: replace irq_gc_ack() with {set,clr}_bit variants (fwd)
arm: mach-vt8500: add forgotten irq_data conversion
ARM: pxa168: correct nand pmu setting
ARM: pxa910: correct nand pmu setting
ARM: pxa: fix PGSR register address calculation
|
|
The macro MIN_MEMORY_BLOCK_SIZE is currently defined twice in two .c
files, and I need it in a third one to fix a powerpc bug, so let's
first move it into a header
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
|
|
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
[media] msp3400: fill in v4l2_tuner based on vt->type field
[media] tuner-core.c: don't change type field in g_tuner or g_frequency
[media] cx18/ivtv: fix g_tuner support
[media] tuner-core: power up tuner when called with s_power(1)
[media] v4l2-ioctl.c: check for valid tuner type in S_HW_FREQ_SEEK
[media] tuner-core: simplify the standard fixup
[media] tuner-core/v4l2-subdev: document that the type field has to be filled in
[media] v4l2-subdev.h: remove unused s_mode tuner op
[media] feature-removal-schedule: change in how radio device nodes are handled
[media] bttv: fix s_tuner for radio
[media] pvrusb2: fix g/s_tuner support
[media] v4l2-ioctl.c: prefill tuner type for g_frequency and g/s_tuner
[media] tuner-core: fix tuner_resume: use t->mode instead of t->type
[media] tuner-core: fix s_std and s_tuner
|
|
This fixes a regression in 3.0 reported by Paul Parsons regarding the
removal of the msleep(1) in the ds1wm_reset() function:
: The linux-3.0-rc4 DS1WM 1-wire driver is logging "bus error, retrying"
: error messages on an HP iPAQ hx4700 PDA (XScale-PXA270):
:
: <snip>
: Driver for 1-wire Dallas network protocol.
: DS1WM w1 busmaster driver - (c) 2004 Szabolcs Gyurko
: 1-Wire driver for the DS2760 battery monitor chip - (c) 2004-2005, Szabolcs Gyurko
: ds1wm ds1wm: pass: 1 bus error, retrying
: ds1wm ds1wm: pass: 2 bus error, retrying
: ds1wm ds1wm: pass: 3 bus error, retrying
: ds1wm ds1wm: pass: 4 bus error, retrying
: ds1wm ds1wm: pass: 5 bus error, retrying
: ...
:
: The visible result is that the battery charging LED is erratic; sometimes
: it works, mostly it doesn't.
:
: The linux-2.6.39 DS1WM 1-wire driver worked OK. I haven't tried 3.0-rc1,
: 3.0-rc2, or 3.0-rc3.
This sleep should not be required on normal circuitry provided the
pull-ups on the bus are correctly adapted to the slaves. Unfortunately,
this is not always the case. The sleep is restored but as a parameter to
the probe function in the pdata.
[akpm@linux-foundation.org: coding-style fixes]
Reported-by: Paul Parsons <lost.distance@yahoo.com>
Tested-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Jean-François Dagenais <dagenaisj@sonatest.com>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Trigger user ABORT if application closes a socket which has data
queued on the socket receive queue or chunks waiting on the
reassembly or ordering queue as this would imply data being lost
which defeats the point of a graceful shutdown.
This behavior is already practiced in TCP.
We do not check the input queue because that would mean to parse
all chunks on it to look for unacknowledged data which seems too
much of an effort. Control chunks or duplicated chunks may also
be in the input queue and should not be stopping a graceful
shutdown.
Signed-off-by: Thomas Graf <tgraf@infradead.org>
Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When initiating a graceful shutdown while having data chunks
on the retransmission queue with a peer which is in zero
window mode the shutdown is never completed because the
retransmission error count is reset periodically by the
following two rules:
- Do not timeout association while doing zero window probe.
- Reset overall error count when a heartbeat request has
been acknowledged.
The graceful shutdown will wait for all outstanding TSN to
be acknowledged before sending the SHUTDOWN request. This
never happens due to the peer's zero window not acknowledging
the continuously retransmitted data chunks. Although the
error counter is incremented for each failed retransmission,
the receiving of the SACK announcing the zero window clears
the error count again immediately. Also heartbeat requests
continue to be sent periodically. The peer acknowledges these
requests causing the error counter to be reset as well.
This patch changes behaviour to only reset the overall error
counter for the above rules while not in shutdown. After
reaching the maximum number of retransmission attempts, the
T5 shutdown guard timer is scheduled to give the receiver
some additional time to recover. The timer is stopped as soon
as the receiver acknowledges any data.
The issue can be easily reproduced by establishing a sctp
association over the loopback device, constantly queueing
data at the sender while not reading any at the receiver.
Wait for the window to reach zero, then initiate a shutdown
by killing both processes simultaneously. The association
will never be freed and the chunks on the retransmission
queue will be retransmitted indefinitely.
Signed-off-by: Thomas Graf <tgraf@infradead.org>
Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* 'for-linus' of git://git.kernel.dk/linux-block:
drbd: we should write meta data updates with FLUSH FUA
drbd: fix limit define, we support 1 PiByte now
drbd: when receive times out on meta socket, also check last receive time on data socket
drbd: account bitmap IO during resync as resync-(related-)-io
drbd: don't cond_resched_lock with IRQs disabled
drbd: add missing spinlock to bitmap receive
drbd: Use the correct max_bio_size when creating resync requests
cfq-iosched: make code consistent
cfq-iosched: fix a rcu warning
|
|
Add an FS-Cache helper to bulk uncache pages on an inode. This will
only work for the circumstance where the pages in the cache correspond
1:1 with the pages attached to an inode's page cache.
This is required for CIFS and NFS: When disabling inode cookie, we were
returning the cookie and setting cifsi->fscache to NULL but failed to
invalidate any previously mapped pages. This resulted in "Bad page
state" errors and manifested in other kind of errors when running
fsstress. Fix it by uncaching mapped pages when we disable the inode
cookie.
This patch should fix the following oops and "Bad page state" errors
seen during fsstress testing.
------------[ cut here ]------------
kernel BUG at fs/cachefiles/namei.c:201!
invalid opcode: 0000 [#1] SMP
Pid: 5, comm: kworker/u:0 Not tainted 2.6.38.7-30.fc15.x86_64 #1 Bochs Bochs
RIP: 0010: cachefiles_walk_to_object+0x436/0x745 [cachefiles]
RSP: 0018:ffff88002ce6dd00 EFLAGS: 00010282
RAX: ffff88002ef165f0 RBX: ffff88001811f500 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000100 RDI: 0000000000000282
RBP: ffff88002ce6dda0 R08: 0000000000000100 R09: ffffffff81b3a300
R10: 0000ffff00066c0a R11: 0000000000000003 R12: ffff88002ae54840
R13: ffff88002ae54840 R14: ffff880029c29c00 R15: ffff88001811f4b0
FS: 00007f394dd32720(0000) GS:ffff88002ef00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 00007fffcb62ddf8 CR3: 000000001825f000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process kworker/u:0 (pid: 5, threadinfo ffff88002ce6c000, task ffff88002ce55cc0)
Stack:
0000000000000246 ffff88002ce55cc0 ffff88002ce6dd58 ffff88001815dc00
ffff8800185246c0 ffff88001811f618 ffff880029c29d18 ffff88001811f380
ffff88002ce6dd50 ffffffff814757e4 ffff88002ce6dda0 ffffffff8106ac56
Call Trace:
cachefiles_lookup_object+0x78/0xd4 [cachefiles]
fscache_lookup_object+0x131/0x16d [fscache]
fscache_object_work_func+0x1bc/0x669 [fscache]
process_one_work+0x186/0x298
worker_thread+0xda/0x15d
kthread+0x84/0x8c
kernel_thread_helper+0x4/0x10
RIP cachefiles_walk_to_object+0x436/0x745 [cachefiles]
---[ end trace 1d481c9af1804caa ]---
I tested the uncaching by the following means:
(1) Create a big file on my NFS server (104857600 bytes).
(2) Read the file into the cache with md5sum on the NFS client. Look in
/proc/fs/fscache/stats:
Pages : mrk=25601 unc=0
(3) Open the file for read/write ("bash 5<>/warthog/bigfile"). Look in proc
again:
Pages : mrk=25601 unc=25601
Reported-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-and-Tested-by: Suresh Jayaraman <sjayaraman@suse.de>
cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
debugobjects: Fix boot crash when kmemleak and debugobjects enabled
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
jump_label: Fix jump_label update for modules
oprofile, x86: Fix race in nmi handler while starting counters
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Disable (revert) SCHED_LOAD_SCALE increase
sched, cgroups: Fix MIN_SHARES on 64-bit boxen
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (31 commits)
sctp: fix missing send up SCTP_SENDER_DRY_EVENT when subscribe it
net: refine {udp|tcp|sctp}_mem limits
vmxnet3: round down # of queues to power of two
net: sh_eth: fix the parameter for the ETHER of SH7757
net: sh_eth: fix cannot work half-duplex mode
net: vlan: enable soft features regardless of underlying device
vmxnet3: fix starving rx ring whenoc_skb kb fails
bridge: Always flood broadcast packets
greth: greth_set_mac_add would corrupt the MAC address.
net: bind() fix error return on wrong address family
natsemi: silence dma-debug warnings
net: 8139too: Initial necessary vlan_features to support vlan
Fix call trace when interrupts are disabled while sleeping function kzalloc is called
qlge:Version change to v1.00.00.29
qlge: Fix printk priority so chip fatal errors are always reported.
qlge:Fix crash caused by mailbox execution on wedged chip.
xfrm4: Don't call icmp_send on local error
ipv4: Don't use ufo handling on later transformed packets
xfrm: Remove family arg from xfrm_bundle_ok
ipv6: Don't put artificial limit on routing table size.
...
|
|
The tuner ops g_frequency, g_tuner and s_tuner require that the tuner type
field is filled in. Document this.
The tuner-core doc is based on a patch from Mauro Carvalho Chehab <mchehab@redhat.com>.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
s_mode is no longer used, so remove it.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This fixes a regression introduced by e59347a "arm: orion:
Use generic irq chip".
Depending on the device, interrupts acknowledgement is done by setting
or by clearing a dedicated register. Replace irq_gc_ack() with some
{set,clr}_bit variants allows to handle both cases.
Note that this patch affects the following SoCs: Davinci, Samsung and
Orion. Except for this last, the change is minor: irq_gc_ack() is just
renamed into irq_gc_ack_set_bit().
For the Orion SoCs, the edge GPIO interrupts support is currently
broken. irq_gc_ack() try to acknowledge a such interrupt by setting
the corresponding cause register bit. The Orion GPIO device expect the
opposite. To fix this issue, the irq_gc_ack_clr_bit() variant is used.
Tested on Network Space v2.
Reported-by: Joey Oravec <joravec@drewtech.com>
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (46 commits)
[media] rc: call input_sync after scancode reports
[media] imon: allow either proto on unknown 0xffdc
[media] imon: auto-config ffdc 7e device
[media] saa7134: fix raw IR timeout value
[media] rc: fix ghost keypresses with certain hw
[media] [staging] lirc_serial: allocate irq at init time
[media] lirc_zilog: fix spinning rx thread
[media] keymaps: fix table for pinnacle pctv hd devices
[media] ite-cir: 8709 needs to use pnp resource 2
[media] V4L: mx1-camera: fix uninitialized variable
[media] omap_vout: Added check in reqbuf & mmap for buf_size allocation
[media] OMAP_VOUT: Change hardcoded device node number to -1
[media] OMAP_VOUTLIB: Fix wrong resizer calculation
[media] uvcvideo: Disable the queue when failing to start
[media] uvcvideo: Remove buffers from the queues when freeing
[media] uvcvideo: Ignore entities for terminals with no supported format
[media] v4l: Don't access media entity after is has been destroyed
[media] media: omap3isp: fix a potential NULL deref
[media] media: vb2: fix allocation failure check
[media] media: vb2: reset queued_count value during queue reinitialization
...
Fix up trivial conflict in MAINTAINERS as per Mauro
|
|
Alex reported that commit c8b281161df ("sched: Increase
SCHED_LOAD_SCALE resolution") caused a power usage regression
under light load as it increases the number of load-balance
operations and keeps idle cpus from staying idle.
Time has run out to find the root cause for this release so
disable the feature for v3.0 until we can figure out what
causes the problem.
Reported-by: "Alex, Shi" <alex.shi@intel.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Nikhil Rao <ncrao@google.com>
Cc: Ming Lei <tom.leiming@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/n/tip-m4onxn0sxnyn5iz9o88eskc3@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
* 'fbdev-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-3.x:
vesafb: fix memory leak
fbdev: amba: Link fb device to its parent
fsl-diu-fb: remove check for pixel clock ranges
udlfb: Correct sub-optimal resolution selection.
hecubafb: add module_put on error path in hecubafb_probe()
sm501fb: fix section mismatch warning
gx1fb: Fix section mismatch warnings
fbdev: sh_mobile_meram: Correct pointer check for YCbCr chroma plane
|
|
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: sb16 - Fix build errors on MIPS and others with 13bit ioctl size
ALSA: hdspm - Fix compile warnings with PPC
ALSA: cs5535 - Fix invalid big-endian conversions
ALSA: HDMI - fix ELD monitor name length
ALSA: atmel - update author email for ABDAC, AC97C and AT73C213
ALSA: HDA: Add model=auto quirk for Acer Aspire 3830TG
ALSA: HDA: Add a new Conexant codec ID (506c)
|
|
IPV6, unlike IPV4, doesn't have a routing cache.
Routing table entries, as well as clones made in response
to route lookup requests, all live in the same table. And
all of these things are together collected in the destination
cache table for ipv6.
This means that routing table entries count against the garbage
collection limits, even though such entries cannot ever be reclaimed
and are added explicitly by the administrator (rather than being
created in response to lookups).
Therefore it makes no sense to count ipv6 routing table entries
against the GC limits.
Add a DST_NOCOUNT destination cache entry flag, and skip the counting
if it is set. Use this flag bit in ipv6 when adding routing table
entries.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
One of ioctl definition in sound/sb16_csp.h contains the data size
over 8kB, and this causes build errors on architectures like MIPS,
which define _IOC_SIZEBITS=13.
For avoiding this build errors but keeping the compatibility, manually
expand with _IOC() instead of using _IOW() for the problematic ioctl.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
|
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
* 'driver-core-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
Connector: Correctly set the error code in case of success when dispatching receive callbacks
Connector: Set the CN_NETLINK_USERS correctly
pti: PTI semantics fix in pti_tty_cleanup.
pti: ENXIO error case memory leak PTI fix.
pti: double-free security PTI fix
drivers:misc: ti-st: fix skipping of change remote baud
drivers/base/platform.c: don't mark platform_device_register_resndata() as __init_or_module
st_kim: Handle case of no device found for ID 0
firmware: fix GOOGLE_SMI kconfig dependency warning
|
Philip Rakity
Per Forlin
James Hogan
Adrian Hunter
Simon Horman
Russell King - ARM Linux
Zhangfei Gao
Robert P. J. Day
Shawn Guo
WANG Cong
Linus Torvalds
Alex Deucher
Michał Mirosław
Len Brown
Lin Ming
Rafael J. Wysocki
Benjamin Herrenschmidt
Jean-François Dagenais
Thomas Graf
David Howells
Hans Verkuil
Simon Guinot
Peter Zijlstra
David S. Miller
John W. Linville
Takashi Iwai
Jens Axboe
Lars Ellenberg