| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
"Hopefully this is the last batch of networking fixes for 4.14
Fingers crossed...
1) Fix stmmac to use the proper sized OF property read, from Bhadram
Varka.
2) Fix use after free in net scheduler tc action code, from Cong
Wang.
3) Fix SKB control block mangling in tcp_make_synack().
4) Use proper locking in fib_dump_info(), from Florian Westphal.
5) Fix IPG encodings in systemport driver, from Florian Fainelli.
6) Fix division by zero in NV TCP congestion control module, from
Konstantin Khlebnikov.
7) Fix use after free in nf_reject_ipv4, from Tejaswi Tanikella"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: systemport: Correct IPG length settings
tcp: do not mangle skb->cb[] in tcp_make_synack()
fib: fib_dump_info can no longer use __in_dev_get_rtnl
stmmac: use of_property_read_u32 instead of read_u8
net_sched: hold netns refcnt for each action
net_sched: acquire RTNL in tc_action_net_exit()
net: vrf: correct FRA_L3MDEV encode type
tcp_nv: fix division by zero in tcpnv_acked()
netfilter: nf_reject_ipv4: Fix use-after-free in send_reset
netfilter: nft_set_hash: disable fast_ops for 2-len keys
|
|
One page may store a set of entries of the sis->swap_map
(swap_info_struct->swap_map) in multiple swap clusters.
If some of the entries has sis->swap_map[offset] > SWAP_MAP_MAX,
multiple pages will be used to store the set of entries of the
sis->swap_map. And the pages are linked with page->lru. This is called
swap count continuation. To access the pages which store the set of
entries of the sis->swap_map simultaneously, previously, sis->lock is
used. But to improve the scalability of __swap_duplicate(), swap
cluster lock may be used in swap_count_continued() now. This may race
with add_swap_count_continuation() which operates on a nearby swap
cluster, in which the sis->swap_map entries are stored in the same page.
The race can cause wrong swap count in practice, thus cause unfreeable
swap entries or software lockup, etc.
To fix the race, a new spin lock called cont_lock is added to struct
swap_info_struct to protect the swap count continuation page list. This
is a lock at the swap device level, so the scalability isn't very well.
But it is still much better than the original sis->lock, because it is
only acquired/released when swap count continuation is used. Which is
considered rare in practice. If it turns out that the scalability
becomes an issue for some workloads, we can split the lock into some
more fine grained locks.
Link: http://lkml.kernel.org/r/20171017081320.28133-1-ying.huang@intel.com
Fixes: 235b62176712 ("mm/swap: add cluster lock")
Signed-off-by: "Huang, Ying" <ying.huang@intel.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Shaohua Li <shli@kernel.org>
Cc: Tim Chen <tim.c.chen@intel.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Aaron Lu <aaron.lu@intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: <stable@vger.kernel.org> [4.11+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In sch_handle_egress and sch_handle_ingress tp->q is used only in order
to update stats. So stats and filter list are the only things that are
needed in clsact qdisc fastpath processing. Introduce new mini_Qdisc
struct to hold those items. Also, introduce a helper to swap the
mini_Qdisc structures in case filter list head changes.
This removes need for tp->q usage without added overhead.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a callback that is to be called whenever head of the chain changes.
Also provide a callback for the default case when the caller gets a
block using non-extended getter.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Devices performing IPv4 forwarding need to update their multipath hash
policy whenever it is changed.
Inform these devices by generating a netevent.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The lan9303 driver defines eth_stp_addr as a synonym to
eth_reserved_addr_base to get the STP ethernet address 01:80:c2:00:00:00.
eth_reserved_addr_base is also used to define the start of Bridge Reserved
ethernet address range, which happen to be the STP address.
br_dev_setup refer to eth_reserved_addr_base as a definition of STP
address.
Clean up by:
- Move the eth_stp_addr definition to linux/etherdevice.h
- Use eth_stp_addr instead of eth_reserved_addr_base in br_dev_setup.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Numbers in DT are stored in “cells” which are 32-bits
in size. of_property_read_u8 does not work properly
because of endianness problem.
This causes it to always return 0 with little-endian
architectures.
Fix it by using of_property_read_u32() OF API.
Signed-off-by: Bhadram Varka <vbhadram@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TC actions have been destroyed asynchronously for a long time,
previously in a RCU callback and now in a workqueue. If we
don't hold a refcnt for its netns, we could use the per netns
data structure, struct tcf_idrinfo, after it has been freed by
netns workqueue.
Hold refcnt to ensure netns destroy happens after all actions
are gone.
Fixes: ddf97ccdd7cb ("net_sched: add network namespace support for tc actions")
Reported-by: Lucas Bates <lucasb@mojatatu.com>
Tested-by: Lucas Bates <lucasb@mojatatu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I forgot to acquire RTNL in tc_action_net_exit()
which leads that action ops->cleanup() is not always
called with RTNL. This usually is not a big deal because
this function is called after all netns refcnt are gone,
but given RTNL protects more than just actions, add it
for safety and consistency.
Also add an assertion to catch other potential bugs.
Fixes: ddf97ccdd7cb ("net_sched: add network namespace support for tc actions")
Reported-by: Lucas Bates <lucasb@mojatatu.com>
Tested-by: Lucas Bates <lucasb@mojatatu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This tracepoint can be used to trace synack retransmits. It maintains
pointer to struct request_sock.
We cannot simply reuse trace_tcp_retransmit_skb() here, because the
sk here is the LISTEN socket. The IP addresses and ports should be
extracted from struct request_sock.
Note that, like many other tracepoints, this patch uses IS_ENABLED
in TP_fast_assign macro, which triggers sparse warning like:
./include/trace/events/tcp.h:274:1: error: directive in argument list
./include/trace/events/tcp.h:281:1: error: directive in argument list
However, there is no good solution to avoid these warnings. To the
best of our knowledge, these warnings are harmless.
Signed-off-by: Song Liu <songliubraving@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RFC 8200 (IPv6) defines Hop-by-Hop options and Destination options
extension headers. Both of these carry a list of TLVs which is
only limited by the maximum length of the extension header (2048
bytes). By the spec a host must process all the TLVs in these
options, however these could be used as a fairly obvious
denial of service attack. I think this could in fact be
a significant DOS vector on the Internet, one mitigating
factor might be that many FWs drop all packets with EH (and
obviously this is only IPv6) so an Internet wide attack might not
be so effective (yet!).
By my calculation, the worse case packet with TLVs in a standard
1500 byte MTU packet that would be processed by the stack contains
1282 invidual TLVs (including pad TLVS) or 724 two byte TLVs. I
wrote a quick test program that floods a whole bunch of these
packets to a host and sure enough there is substantial time spent
in ip6_parse_tlv. These packets contain nothing but unknown TLVS
(that are ignored), TLV padding, and bogus UDP header with zero
payload length.
25.38% [kernel] [k] __fib6_clean_all
21.63% [kernel] [k] ip6_parse_tlv
4.21% [kernel] [k] __local_bh_enable_ip
2.18% [kernel] [k] ip6_pol_route.isra.39
1.98% [kernel] [k] fib6_walk_continue
1.88% [kernel] [k] _raw_write_lock_bh
1.65% [kernel] [k] dst_release
This patch adds configurable limits to Destination and Hop-by-Hop
options. There are three limits that may be set:
- Limit the number of options in a Hop-by-Hop or Destination options
extension header.
- Limit the byte length of a Hop-by-Hop or Destination options
extension header.
- Disallow unrecognized options in a Hop-by-Hop or Destination
options extension header.
The limits are set in corresponding sysctls:
ipv6.sysctl.max_dst_opts_cnt
ipv6.sysctl.max_hbh_opts_cnt
ipv6.sysctl.max_dst_opts_len
ipv6.sysctl.max_hbh_opts_len
If a max_*_opts_cnt is less than zero then unknown TLVs are disallowed.
The number of known TLVs that are allowed is the absolute value of
this number.
If a limit is exceeded when processing an extension header the packet is
dropped.
Default values are set to 8 for options counts, and set to INT_MAX
for maximum length. Note the choice to limit options to 8 is an
arbitrary guess (roughly based on the fact that the stack supports
three HBH options and just one destination option).
These limits have being proposed in draft-ietf-6man-rfc6434-bis.
Tested (by Martin Lau)
I tested out 1 thread (i.e. one raw_udp process).
I changed the net.ipv6.max_dst_(opts|hbh)_number between 8 to 2048.
With sysctls setting to 2048, the softirq% is packed to 100%.
With 8, the softirq% is almost unnoticable from mpstat.
v2;
- Code and documention cleanup.
- Change references of RFC2460 to be RFC8200.
- Add reference to RFC6434-bis where the limits will be in standard.
Signed-off-by: Tom Herbert <tom@quantonium.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull initial SPDX identifiers from Greg KH:
"License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the
'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
binding shorthand, which can be used instead of the full boiler plate
text.
This patch is based on work done by Thomas Gleixner and Kate Stewart
and Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset
of the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to
license had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied
to a file was done in a spreadsheet of side by side results from of
the output of two independent scanners (ScanCode & Windriver)
producing SPDX tag:value files created by Philippe Ombredanne.
Philippe prepared the base worksheet, and did an initial spot review
of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537
files assessed. Kate Stewart did a file by file comparison of the
scanner results in the spreadsheet to determine which SPDX license
identifier(s) to be applied to the file. She confirmed any
determination that was not immediately clear with lawyers working with
the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained
>5 lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that
became the concluded license(s).
- when there was disagreement between the two scanners (one detected
a license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply
(and which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases,
confirmation by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.
The Windriver scanner is based on an older version of FOSSology in
part, so they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot
checks in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect
the correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial
patch version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch
license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
applied SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
License cleanup: add SPDX license identifier to uapi header files with a license
License cleanup: add SPDX license identifier to uapi header files with no license
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
|
|
Many user space API headers have licensing information, which is either
incomplete, badly formatted or just a shorthand for referring to the
license under which the file is supposed to be. This makes it hard for
compliance tools to determine the correct license.
Update these files with an SPDX license identifier. The identifier was
chosen based on the license information in the file.
GPL/LGPL licensed headers get the matching GPL/LGPL SPDX license
identifier with the added 'WITH Linux-syscall-note' exception, which is
the officially assigned exception identifier for the kernel syscall
exception:
NOTE! This copyright does *not* cover user programs that use kernel
services by normal system calls - this is merely considered normal use
of the kernel, and does *not* fall under the heading of "derived work".
This exception makes it possible to include GPL headers into non GPL
code, without confusing license compliance tools.
Headers which have either explicit dual licensing or are just licensed
under a non GPL license are updated with the corresponding SPDX
identifier and the GPLv2 with syscall exception identifier. The format
is:
((GPL-2.0 WITH Linux-syscall-note) OR SPDX-ID-OF-OTHER-LICENSE)
SPDX license identifiers are a legally binding shorthand, which can be
used instead of the full boiler plate text. The update does not remove
existing license information as this has to be done on a case by case
basis and the copyright holders might have to be consulted. This will
happen in a separate step.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne. See the previous patch in this series for the
methodology of how this patch was researched.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Many user space API headers are missing licensing information, which
makes it hard for compliance tools to determine the correct license.
By default are files without license information under the default
license of the kernel, which is GPLV2. Marking them GPLV2 would exclude
them from being included in non GPLV2 code, which is obviously not
intended. The user space API headers fall under the syscall exception
which is in the kernels COPYING file:
NOTE! This copyright does *not* cover user programs that use kernel
services by normal system calls - this is merely considered normal use
of the kernel, and does *not* fall under the heading of "derived work".
otherwise syscall usage would not be possible.
Update the files which contain no license information with an SPDX
license identifier. The chosen identifier is 'GPL-2.0 WITH
Linux-syscall-note' which is the officially assigned identifier for the
Linux syscall exception. SPDX license identifiers are a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne. See the previous patch in this series for the
methodology of how this patch was researched.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Touching linux/bpf.h makes us rebuild a surprisingly large
portion of the kernel. Remove the unnecessary dependency
from security.h, it only needs forward declarations.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since tc_can_offload is always called from block callback or egdev
callback, no need to check if ndo_setup_tc exists.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tc_should_offload is no longer used, remove it.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Smooth Cong Wang's bug fix into 'net-next'. Basically put
the bulk of the tcf_block_put() logic from 'net' into
tcf_block_put_ext(), but after the offload unbind.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) Fix refcounting in xfrm_bundle_lookup() when using a dummy bundle,
from Steffen Klassert.
2) Fix crypto header handling in rx data frames in ath10k driver, from
Vasanthakumar Thiagarajan.
3) Fix use after free of qdisc when we defer tcp_chain_flush() to a
workqueue. From Cong Wang.
4) Fix double free in lapbether driver, from Pan Bian.
5) Sanitize TUNSETSNDBUF values, from Craig Gallek.
6) Fix refcounting when addrconf_permanent_addr() calls
ipv6_del_addr(). From Eric Dumazet.
7) Fix MTU probing bug in TCP that goes back to 2007, from Eric
Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
tcp: fix tcp_mtu_probe() vs highest_sack
ipv6: addrconf: increment ifp refcount before ipv6_del_addr()
tun/tap: sanitize TUNSETSNDBUF input
mlxsw: i2c: Fix buffer increment counter for write transaction
mlxsw: reg: Add high and low temperature thresholds
MAINTAINERS: Remove Yotam from mlxfw
MAINTAINERS: Update Yotam's E-mail
net: hns: set correct return value
net: lapbether: fix double free
bpf: remove SK_REDIRECT from UAPI
net: phy: marvell: Only configure RGMII delays when using RGMII
xfrm: Fix GSO for IPsec with GRE tunnel.
tc-testing: fix arg to ip command: -s -> -n
net_sched: remove tcf_block_put_deferred()
l2tp: hold tunnel in pppol2tp_connect()
Revert "ath10k: fix napi_poll budget overflow"
ath10k: rebuild crypto header in rx data frames
wcn36xx: Remove unnecessary rcu_read_unlock in wcn36xx_bss_info_changed
xfrm: Clear sk_dst_cache when applying per-socket policy.
xfrm: Fix xfrm_dst_cache memleak
|
|
Johan Hedberg says:
====================
pull request: bluetooth-next 2017-11-01
Here's one more bluetooth-next pull request for the 4.15 kernel.
- New NFA344A device entry for btusb drvier
- Fix race conditions in hci_ldisc
- Fix for isochronous interface assignments in btusb driver
- A few other smaller fixes & improvements
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
STP BPDUs arriving on user ports must sent to CPU port only,
for processing by the SW bridge.
Add an ALR entry with STP state override to fix that.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based on SNMP values provided by Roman, Yuchung made the observation
that some crashes in tcp_sacktag_walk() might be caused by MTU probing.
Looking at tcp_mtu_probe(), I found that when a new skb was placed
in front of the write queue, we were not updating tcp highest sack.
If one skb is freed because all its content was copied to the new skb
(for MTU probing), then tp->highest_sack could point to a now freed skb.
Bad things would then happen, including infinite loops.
This patch renames tcp_highest_sack_combine() and uses it
from tcp_mtu_probe() to fix the bug.
Note that I also removed one test against tp->sacked_out,
since we want to replace tp->highest_sack regardless of whatever
condition, since keeping a stale pointer to freed skb is a recipe
for disaster.
Fixes: a47e5a988a57 ("[TCP]: Convert highest_sack to sk_buff to allow direct access")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Reported-by: Roman Gushchin <guro@fb.com>
Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch updates the error messages displayed in kernel log to include
hwaddress of the source machine that caused ipv6 duplicate address
detection failures.
Examples:
a) When we receive a NA packet from another machine advertising our
address:
ICMPv6: NA: 34:ab:cd:56:11:e8 advertised our address 2001:db8:: on eth0!
b) When we detect DAD failure during address assignment to an interface:
IPv6: eth0: IPv6 duplicate address 2001:db8:: used by 34:ab:cd:56:11:e8
detected!
v2:
Changed %pI6 to %pI6c in ndisc_recv_na()
Chaged the v6 address in the commit message to 2001:db8::
Suggested-by: Igor Lubashev <ilubashe@akamai.com>
Signed-off-by: Vishwanath Pai <vpai@akamai.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2017-10-30
1) Change some variables that can't be negative
from int to unsigned int. From Alexey Dobriyan.
2) Remove a redundant header initialization in esp6.
From Colin Ian King.
3) Some BUG to BUG_ON conversions.
From Gustavo A. R. Silva.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add extack to fib_notifier_info and plumb through stack to
call_fib_rule_notifiers, call_fib_entry_notifiers and
call_fib6_entry_notifiers. This allows notifer handlers to
return messages to user.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that SK_REDIRECT is no longer a valid return code. Remove it
from the UAPI completely. Then do a namespace remapping internal
to sockmap so SK_REDIRECT is no longer externally visible.
Patchs primary change is to do a namechange from SK_REDIRECT to
__SK_REDIRECT
Reported-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
the verifier got progressively smarter over time and size of its internal
state grew as well. Time to reduce the memory consumption.
Before:
sizeof(struct bpf_verifier_state) = 6520
After:
sizeof(struct bpf_verifier_state) = 896
It's done by observing that majority of BPF programs use little to
no stack whereas verifier kept all of 512 stack slots ready always.
Instead dynamically reallocate struct verifier state when stack
access is detected.
Runtime difference before vs after is within a noise.
The number of processed instructions stays the same.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch offloads the classid to hardware and uses the classid
reserved in the range :ffe0 - :ffef to identify hardware traffic
classes reported via dev->num_tc.
tcf_result structure contains the class ID of the class to which
the packet belongs and is offloaded to hardware via flower filter.
A new helper function is introduced to represent HW traffic
classes 0 through 15 using the reserved classid values :ffe0 - :ffef.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This reverts commit 0cc2b4e5a020 (PM / QoS: Fix device resume latency PM
QoS) as it introduced regressions on multiple systems and the fix-up
in commit 2a9a86d5c813 (PM / QoS: Fix default runtime_pm device resume
latency) does not address all of them.
The original problem that commit 0cc2b4e5a020 was attempting to fix
will be addressed later.
Fixes: 0cc2b4e5a020 (PM / QoS: Fix device resume latency PM QoS)
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This reverts commit 2a9a86d5c813 (PM / QoS: Fix default runtime_pm
device resume latency) as the commit it depends on is going to be
reverted.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Several conflicts here.
NFP driver bug fix adding nfp_netdev_is_nfp_repr() check to
nfp_fl_output() needed some adjustments because the code block is in
an else block now.
Parallel additions to net/pkt_cls.h and net/sch_generic.h
A bug fix in __tcp_retransmit_skb() conflicted with some of
the rbtree changes in net-next.
The tc action RCU callback fixes in 'net' had some overlap with some
of the recent tcf_block reworking.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case of using BT_ERR and BT_INFO, convert to bt_dev_err and
bt_dev_info when possible. This allows for controller specific
reporting.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The recent change to the PM QoS framework to introduce a proper
no constraint value overlooked to handle the devices which don't
implement PM QoS OPS. Runtime PM is one of the more severely
impacted subsystems, failing every attempt to runtime suspend
a device. This leads into some nasty second level issues like
probe failures and increased power consumption among other
things.
Fix this by adding a proper return value for devices that don't
implement PM QoS.
Fixes: 0cc2b4e5a020 (PM / QoS: Fix device resume latency PM QoS)
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Pull networking fixes from David Miller:
1) Fix route leak in xfrm_bundle_create().
2) In mac80211, validate user rate mask before configuring it. From
Johannes Berg.
3) Properly enforce memory limits in fair queueing code, from Toke
Hoiland-Jorgensen.
4) Fix lockdep splat in inet_csk_route_req(), from Eric Dumazet.
5) Fix TSO header allocation and management in mvpp2 driver, from Yan
Markman.
6) Don't take socket lock in BH handler in strparser code, from Tom
Herbert.
7) Don't show sockets from other namespaces in AF_UNIX code, from
Andrei Vagin.
8) Fix double free in error path of tap_open(), from Girish Moodalbail.
9) Fix TX map failure path in igb and ixgbe, from Jean-Philippe Brucker
and Alexander Duyck.
10) Fix DCB mode programming in stmmac driver, from Jose Abreu.
11) Fix err_count handling in various tunnels (ipip, ip6_gre). From Xin
Long.
12) Properly align SKB head before building SKB in tuntap, from Jason
Wang.
13) Avoid matching qdiscs with a zero handle during lookups, from Cong
Wang.
14) Fix various endianness bugs in sctp, from Xin Long.
15) Fix tc filter callback races and add selftests which trigger the
problem, from Cong Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (73 commits)
selftests: Introduce a new test case to tc testsuite
selftests: Introduce a new script to generate tc batch file
net_sched: fix call_rcu() race on act_sample module removal
net_sched: add rtnl assertion to tcf_exts_destroy()
net_sched: use tcf_queue_work() in tcindex filter
net_sched: use tcf_queue_work() in rsvp filter
net_sched: use tcf_queue_work() in route filter
net_sched: use tcf_queue_work() in u32 filter
net_sched: use tcf_queue_work() in matchall filter
net_sched: use tcf_queue_work() in fw filter
net_sched: use tcf_queue_work() in flower filter
net_sched: use tcf_queue_work() in flow filter
net_sched: use tcf_queue_work() in cgroup filter
net_sched: use tcf_queue_work() in bpf filter
net_sched: use tcf_queue_work() in basic filter
net_sched: introduce a workqueue for RCU callbacks of tc filter
sctp: fix some type cast warnings introduced since very beginning
sctp: fix a type cast warnings that causes a_rwnd gets the wrong value
sctp: fix some type cast warnings introduced by transport rhashtable
sctp: fix some type cast warnings introduced by stream reconf
...
|
|
This patch introduces a dedicated workqueue for tc filters
so that each tc filter's RCU callback could defer their
action destroy work to this workqueue. The helper
tcf_queue_work() is introduced for them to use.
Because we hold RTNL lock when calling tcf_block_put(), we
can not simply flush works inside it, therefore we have to
defer it again to this workqueue and make sure all flying RCU
callbacks have already queued their work before this one, in
other words, to ensure this is the last one to execute to
prevent any use-after-free.
On the other hand, this makes tcf_block_put() ugly and
harder to understand. Since David and Eric strongly dislike
adding synchronize_rcu(), this is probably the only
solution that could make everyone happy.
Please also see the code comments below.
Reported-by: Chris Mi <chrism@mellanox.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch increases the connection timeout for LE connections that are
triggered by the advertising report to 4 seconds.
It has been observed that devices equipped with wifi+bt combo SoC fail
to create a connection with BLE devices due to their coexistence issues.
Increasing this timeout gives them enough time to complete the
connection with success.
Signed-off-by: Konrad Zapałowicz <konrad.zapalowicz@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This is very similar to the Macvlan VEPA mode, however, there is some
difference. IPvlan uses the mac-address of the lower device, so the VEPA
mode has implications of ICMP-redirects for packets destined for its
immediate neighbors sharing same master since the packets will have same
source and dest mac. The external switch/router will send redirect msg.
Having said that, this will be useful tool in terms of debugging
since IPvlan will not switch packets within its slaves and rely completely
on the external entity as intended in 802.1Qbg.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPvlan has always operated in bridge mode. However there are scenarios
where each slave should be able to talk through the master device but
not necessarily across each other. Think of an environment where each
of a namespace is a private and independant customer. In this scenario
the machine which is hosting these namespaces neither want to tell who
their neighbor is nor the individual namespaces care to talk to neighbor
on short-circuited network path.
This patch implements the mode that is very similar to the 'private' mode
in macvlan where individual slaves can send and receive traffic through
the master device, just that they can not talk among slave devices.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These warnings were found by running 'make C=2 M=net/sctp/'.
They are there since very beginning.
Note after this patch, there still one warning left in
sctp_outq_flush():
sctp_chunk_fail(chunk, SCTP_ERROR_INV_STRM)
Since it has been moved to sctp_stream_outq_migrate on net-next,
to avoid the extra job when merging net-next to net, I will post
the fix for it after the merging is done.
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These warnings were found by running 'make C=2 M=net/sctp/'.
They are introduced by not aware of Endian when coding stream
reconf patches.
Since commit c0d8bab6ae51 ("sctp: add get and set sockopt for
reconf_enable") enabled stream reconf feature for users, the
Fixes tag below would use it.
Fixes: c0d8bab6ae51 ("sctp: add get and set sockopt for reconf_enable")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cached routes should only be created by the system when receiving pmtu
discovery or ip redirect msg. Users should not be allowed to create
cached routes.
Furthermore, after the patch series to move cached routes into exception
table, user added cached routes will trigger the following warning in
fib6_add():
WARNING: CPU: 0 PID: 2985 at net/ipv6/ip6_fib.c:1137
fib6_add+0x20d9/0x2c10 net/ipv6/ip6_fib.c:1137
Kernel panic - not syncing: panic_on_warn set ...
CPU: 0 PID: 2985 Comm: syzkaller320388 Not tainted 4.14.0-rc3+ #74
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:16 [inline]
dump_stack+0x194/0x257 lib/dump_stack.c:52
panic+0x1e4/0x417 kernel/panic.c:181
__warn+0x1c4/0x1d9 kernel/panic.c:542
report_bug+0x211/0x2d0 lib/bug.c:183
fixup_bug+0x40/0x90 arch/x86/kernel/traps.c:178
do_trap_no_signal arch/x86/kernel/traps.c:212 [inline]
do_trap+0x260/0x390 arch/x86/kernel/traps.c:261
do_error_trap+0x120/0x390 arch/x86/kernel/traps.c:298
do_invalid_op+0x1b/0x20 arch/x86/kernel/traps.c:311
invalid_op+0x18/0x20 arch/x86/entry/entry_64.S:905
RIP: 0010:fib6_add+0x20d9/0x2c10 net/ipv6/ip6_fib.c:1137
RSP: 0018:ffff8801cf09f6a0 EFLAGS: 00010297
RAX: ffff8801ce45e340 RBX: 1ffff10039e13eec RCX: ffff8801d749c814
RDX: 0000000000000000 RSI: ffff8801d749c700 RDI: ffff8801d749c780
RBP: ffff8801cf09fa08 R08: 0000000000000000 R09: ffff8801cf09f360
R10: ffff8801cf09f2d8 R11: 1ffff10039c8befb R12: 0000000000000001
R13: dffffc0000000000 R14: ffff8801d749c700 R15: ffffffff860655c0
__ip6_ins_rt+0x6c/0x90 net/ipv6/route.c:1011
ip6_route_add+0x148/0x1a0 net/ipv6/route.c:2782
ipv6_route_ioctl+0x4d5/0x690 net/ipv6/route.c:3291
inet6_ioctl+0xef/0x1e0 net/ipv6/af_inet6.c:521
sock_do_ioctl+0x65/0xb0 net/socket.c:961
sock_ioctl+0x2c2/0x440 net/socket.c:1058
vfs_ioctl fs/ioctl.c:45 [inline]
do_vfs_ioctl+0x1b1/0x1530 fs/ioctl.c:685
SYSC_ioctl fs/ioctl.c:700 [inline]
SyS_ioctl+0x8f/0xc0 fs/ioctl.c:691
entry_SYSCALL_64_fastpath+0x1f/0xbe
So we fix this by failing the attemp to add cached routes from userspace
with returning EINVAL error.
Fixes: 2b760fcf5cfb ("ipv6: hook up exception table to store dst cache")
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jeff Kirsher says:
====================
1GbE Intel Wired LAN Driver Updates 2017-10-27
This patchset is a proposal of how the Traffic Control subsystem can
be used to offload the configuration of the Credit Based Shaper
(defined in the IEEE 802.1Q-2014 Section 8.6.8.2) into supported
network devices.
As part of this work, we've assessed previous public discussions
related to TSN enabling: patches from Henrik Austad (Cisco), the
presentation from Eric Mann at Linux Plumbers 2012, patches from
Gangfeng Huang (National Instruments) and the current state of the
OpenAVNU project (https://github.com/AVnu/OpenAvnu/).
Overview
========
Time-sensitive Networking (TSN) is a set of standards that aim to
address resources availability for providing bandwidth reservation and
bounded latency on Ethernet based LANs. The proposal described here
aims to cover mainly what is needed to enable the following standards:
802.1Qat and 802.1Qav.
The initial target of this work is the Intel i210 NIC, but other
controllers' datasheet were also taken into account, like the Renesas
RZ/A1H RZ/A1M group and the Synopsis DesignWare Ethernet QoS
controller.
Proposal
========
Feature-wise, what is covered here is the configuration interfaces for
HW implementations of the Credit-Based shaper (CBS, 802.1Qav). CBS is
a per-queue shaper. Given that this feature is related to traffic
shaping, and that the traffic control subsystem already provides a
queueing discipline that offloads config into the device driver (i.e.
mqprio), designing a new qdisc for the specific purpose of offloading
the config for the CBS shaper seemed like a good fit.
For steering traffic into the correct queues, we use the socket option
SO_PRIORITY and then a mechanism to map priority to traffic classes /
Tx queues. The qdisc mqprio is currently used in our tests.
As for the CBS config interface, this patchset is proposing a new
qdisc called 'cbs'. Its 'tc' cmd line is:
$ tc qdisc add dev IFACE parent ID cbs locredit N hicredit M sendslope S \
idleslope I
Note that the parameters for this qdisc are the ones defined by the
802.1Q-2014 spec, so no hardware specific functionality is exposed here.
Per-stream shaping, as defined by IEEE 802.1Q-2014 Section 34.6.1, is
not yet covered by this proposal.
v2: Merged patch 6 of the original series into patch 4 based on feedback
from David Miller.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recent additions to support multiple programs in cgroups impose
a strict requirement, "all yes is yes, any no is no". To enforce
this the infrastructure requires the 'no' return code, SK_DROP in
this case, to be 0.
To apply these rules to SK_SKB program types the sk_actions return
codes need to be adjusted.
This fix adds SK_PASS and makes 'SK_DROP = 0'. Finally, remove
SK_ABORTED to remove any chance that the API may allow aborted
program flows to be passed up the stack. This would be incorrect
behavior and allow programs to break existing policies.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SK_SKB program types use bpf_compute_data to store the end of the
packet data. However, bpf_compute_data assumes the cb is stored in the
qdisc layer format. But, for SK_SKB this is the wrong layer of the
stack for this type.
It happens to work (sort of!) because in most cases nothing happens
to be overwritten today. This is very fragile and error prone.
Fortunately, we have another hole in tcp_skb_cb we can use so lets
put the data_end value there.
Note, SK_SKB program types do not use data_meta, they are failed by
sk_skb_is_valid_access().
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
two extra #include are not necessary in tcp.h
Remove them.
Fixes: 40304b2a1567 ("bpf: BPF support for sock_ops")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Also remove an obsolete comment about TCP pacing.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
David S. Miller
Linus Torvalds
Huang Ying
Jiri Pirko
Ido Schimmel
Egil Hjelmeland
Bhadram Varka
Cong Wang
Song Liu
Tom Herbert
Greg Kroah-Hartman
Jakub Kicinski
Eric Dumazet
Vishwanath Pai
David Ahern
John Fastabend
Alexei Starovoitov
Amritha Nambiar
Rafael J. Wysocki
Marcel Holtmann
Tero Kristo
Konrad Zapałowicz
Mahesh Bandewar
Xin Long
Wei Wang