| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
since commit d6b915e29f4adea9
("ip_fragment: don't forward defragmented DF packet") the largest
fragment size is available in the IPCB.
Therefore we no longer need to care about 'encapsulation'
overhead of stripped PPPOE/VLAN headers since ip_do_fragment
doesn't use device mtu in such cases.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
IPv6 fragmented packets are not forwarded on an ethernet bridge
with netfilter ip6_tables loaded. e.g. steps to reproduce
1) create a simple bridge like this
modprobe br_netfilter
brctl addbr br0
brctl addif br0 eth0
brctl addif br0 eth2
ifconfig eth0 up
ifconfig eth2 up
ifconfig br0 up
2) place a host with an IPv6 address on each side of the bridge
set IPv6 address on host A:
ip -6 addr add fd01:2345:6789:1::1/64 dev eth0
set IPv6 address on host B:
ip -6 addr add fd01:2345:6789:1::2/64 dev eth0
3) run a simple ping command on host A with packets > MTU
ping6 -s 4000 fd01:2345:6789:1::2
4) wait some time and run e.g. "ip6tables -t nat -nvL" on the bridge
IPv6 fragmented packets traverse the bridge cleanly until somebody runs.
"ip6tables -t nat -nvL". As soon as it is run (and netfilter modules are
loaded) IPv6 fragmented packets do not traverse the bridge any more (you
see no more responses in ping's output).
After applying this patch IPv6 fragmented packets traverse the bridge
cleanly in above scenario.
Signed-off-by: Bernhard Thaler <bernhard.thaler@wvnet.at>
[pablo@netfilter.org: small changes to br_nf_dev_queue_xmit]
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Currently frag_max_size is member of br_input_skb_cb and copied back and
forth using IPCB(skb) and BR_INPUT_SKB_CB(skb) each time it is changed or
used.
Attach frag_max_size to nf_bridge_info and set value in pre_routing and
forward functions. Use its value in forward and xmit functions.
Signed-off-by: Bernhard Thaler <bernhard.thaler@wvnet.at>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
IPv4 iptables allows to REDIRECT/DNAT/SNAT any traffic over a bridge.
e.g. REDIRECT
$ sysctl -w net.bridge.bridge-nf-call-iptables=1
$ iptables -t nat -A PREROUTING -p tcp -m tcp --dport 8080 \
-j REDIRECT --to-ports 81
This does not work with ip6tables on a bridge in NAT66 scenario
because the REDIRECT/DNAT/SNAT is not correctly detected.
The bridge pre-routing (finish) netfilter hook has to check for a possible
redirect and then fix the destination mac address. This allows to use the
ip6tables rules for local REDIRECT/DNAT/SNAT REDIRECT similar to the IPv4
iptables version.
e.g. REDIRECT
$ sysctl -w net.bridge.bridge-nf-call-ip6tables=1
$ ip6tables -t nat -A PREROUTING -p tcp -m tcp --dport 8080 \
-j REDIRECT --to-ports 81
This patch makes it possible to use IPv6 NAT66 on a bridge. It was tested
on a bridge with two interfaces using SNAT/DNAT NAT66 rules.
Reported-by: Artie Hamilton <artiemhamilton@yahoo.com>
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
[bernhard.thaler@wvnet.at: rebased, add indirect call to ip6_route_input()]
[bernhard.thaler@wvnet.at: rebased, split into separate patches]
Signed-off-by: Bernhard Thaler <bernhard.thaler@wvnet.at>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
In commit cd7d8498c9a5 ("tcp: change tcp_skb_pcount() location") we stored
gso_segs in a temporary cache hot location.
This patch does the same for gso_size.
This allows to save 2 cache line misses in tcp xmit path for
the last packet that is considered but not sent because of
various conditions (cwnd, tso defer, receiver window, TSQ...)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enable HW cacheline start padding and align RX WQE size to cacheline
while considering HW start padding. Also, fix dma_unmap call to use
the correct SKB data buffer size.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously we configured HW MTU to be netdev->mtu, actually we
need to configure netdev->mtu + (ETH_HLEN + VLAN_HLEN + ETH_FCS_LEN).
Also, query MTU can not fail, hence make the relevant helper a
void functionm, add mlx5e_set_dev_port_mtu, helper function to
handle MTU setting.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add strings array of the current supported tunable options.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Define the pseudo-PHY address (30) which is used by all Broadcom
Ethernet switches in a shared header file.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We utilize inline functions from the PHY library, make sure that we do
include phy.h in brcmphy.h in order for the code including brcmphy.h not
to have to resolve this inclusion dependency.
Fixes: 705314797b8b ("net: phy: broadcom: move shadow 0x1C register accessors to brcmphy.h")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Johannes Berg says:
====================
For this round we mostly have fixes:
* mesh fixes from Alexis Green and Chun-Yeow Yeoh,
* a documentation fix from Jakub Kicinski,
* a missing channel release (from Michal Kazior),
* a fix for a signal strength reporting bug (from Sara Sharon),
* handle deauth while associating (myself),
* don't report mangled TX SKB back to userspace for status (myself),
* handle aggregation session timeouts properly in fast-xmit (myself)
However, there are also a few cleanups and one big change that
affects all drivers (and that required me to pull in your tree)
to change the mac80211 HW flags to use an unsigned long bitmap
so that we can extend them more easily - we're running out of
flags even with a cleanup to remove the two unused ones.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SCM_SECURITY was originally only implemented for datagram sockets,
not for stream sockets. However, SCM_CREDENTIALS is supported on
Unix stream sockets. For consistency, implement Unix stream support
for SCM_SECURITY as well. Also clean up the existing code and get
rid of the superfluous UNIXSID macro.
Motivated by https://bugzilla.redhat.com/show_bug.cgi?id=1224211,
where systemd was using SCM_CREDENTIALS and assumed wrongly that
SCM_SECURITY was also supported on Unix stream sockets.
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As we're running out of hardware capability flags pretty quickly,
convert them to use the regular test_bit() style unsigned long
bitmaps.
This introduces a number of helper functions/macros to set and to
test the bits, along with new debugfs code.
The occurrences of an explicit __clear_bit() are intentional, the
drivers were never supposed to change their supported bits on the
fly. We should investigate changing this to be a per-frame flag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Merge back net-next to get wireless driver changes (from Kalle)
to be able to create the API change across all trees properly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
FIF_PROMISC_IN_BSS was removed in commit df1404650ccb
("mac80211: remove support for IFF_PROMISC").
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Similar to referencing iptables rules by their line number this UID allows to
reference created routing jobs, e.g. to alter configured data modifications.
The UID is an optional non-zero value which can be provided at routing job
creation time. When the UID is set the UID replaces the data modification
configuration as job identification attribute e.g. at job removal time.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
|
|
Fix static checker warnings in the flow of system guid query.
Fixes: 707c4602cda6 ('net/mlx5_core: Add new query HCA vport commands')
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPv4 and IPv6 share same implementation of get_cookie_sock(),
and there is no point inlining it.
We add tcp_ prefix to the common helper name and export it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
allow programs read/write skb->mark, tc_index fields and
((struct qdisc_skb_cb *)cb)->data.
mark and tc_index are generically useful in TC.
cb[0]-cb[4] are primarily used to pass arguments from one
program to another called via bpf_tail_call() which can
be seen in sockex3_kern.c example.
All fields of 'struct __sk_buff' are readable to socket and tc_cls_act progs.
mark, tc_index are writeable from tc_cls_act only.
cb[0]-cb[4] are writeable by both sockets and tc_cls_act.
Add verifier tests and improve sample code.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When an application needs to force a source IP on an active TCP socket
it has to use bind(IP, port=x).
As most applications do not want to deal with already used ports, x is
often set to 0, meaning the kernel is in charge to find an available
port.
But kernel does not know yet if this socket is going to be a listener or
be connected.
It has very limited choices (no full knowledge of final 4-tuple for a
connect())
With limited ephemeral port range (about 32K ports), it is very easy to
fill the space.
This patch adds a new SOL_IP socket option, asking kernel to ignore
the 0 port provided by application in bind(IP, port=0) and only
remember the given IP address.
The port will be automatically chosen at connect() time, in a way
that allows sharing a source port as long as the 4-tuples are unique.
This new feature is available for both IPv4 and IPv6 (Thanks Neal)
Tested:
Wrote a test program and checked its behavior on IPv4 and IPv6.
strace(1) shows sequences of bind(IP=127.0.0.2, port=0) followed by
connect().
Also getsockname() show that the port is still 0 right after bind()
but properly allocated after connect().
socket(PF_INET, SOCK_STREAM, IPPROTO_IP) = 5
setsockopt(5, SOL_IP, IP_BIND_ADDRESS_NO_PORT, [1], 4) = 0
bind(5, {sa_family=AF_INET, sin_port=htons(0), sin_addr=inet_addr("127.0.0.2")}, 16) = 0
getsockname(5, {sa_family=AF_INET, sin_port=htons(0), sin_addr=inet_addr("127.0.0.2")}, [16]) = 0
connect(5, {sa_family=AF_INET, sin_port=htons(53174), sin_addr=inet_addr("127.0.0.3")}, 16) = 0
getsockname(5, {sa_family=AF_INET, sin_port=htons(38050), sin_addr=inet_addr("127.0.0.2")}, [16]) = 0
IPv6 test :
socket(PF_INET6, SOCK_STREAM, IPPROTO_IP) = 7
setsockopt(7, SOL_IP, IP_BIND_ADDRESS_NO_PORT, [1], 4) = 0
bind(7, {sa_family=AF_INET6, sin6_port=htons(0), inet_pton(AF_INET6, "::1", &sin6_addr), sin6_flowinfo=0, sin6_scope_id=0}, 28) = 0
getsockname(7, {sa_family=AF_INET6, sin6_port=htons(0), inet_pton(AF_INET6, "::1", &sin6_addr), sin6_flowinfo=0, sin6_scope_id=0}, [28]) = 0
connect(7, {sa_family=AF_INET6, sin6_port=htons(57300), inet_pton(AF_INET6, "::1", &sin6_addr), sin6_flowinfo=0, sin6_scope_id=0}, 28) = 0
getsockname(7, {sa_family=AF_INET6, sin6_port=htons(60964), inet_pton(AF_INET6, "::1", &sin6_addr), sin6_flowinfo=0, sin6_scope_id=0}, [28]) = 0
I was able to bind()/connect() a million concurrent IPv4 sockets,
instead of ~32000 before patch.
lpaa23:~# ulimit -n 1000010
lpaa23:~# ./bind --connect --num-flows=1000000 &
1000000 sockets
lpaa23:~# grep TCP /proc/net/sockstat
TCP: inuse 2000063 orphan 0 tw 47 alloc 2000157 mem 66
Check that a given source port is indeed used by many different
connections :
lpaa23:~# ss -t src :40000 | head -10
State Recv-Q Send-Q Local Address:Port Peer Address:Port
ESTAB 0 0 127.0.0.2:40000 127.0.202.33:44983
ESTAB 0 0 127.0.0.2:40000 127.2.27.240:44983
ESTAB 0 0 127.0.0.2:40000 127.2.98.5:44983
ESTAB 0 0 127.0.0.2:40000 127.0.124.196:44983
ESTAB 0 0 127.0.0.2:40000 127.2.139.38:44983
ESTAB 0 0 127.0.0.2:40000 127.1.59.80:44983
ESTAB 0 0 127.0.0.2:40000 127.3.6.228:44983
ESTAB 0 0 127.0.0.2:40000 127.0.38.53:44983
ESTAB 0 0 127.0.0.2:40000 127.1.197.10:44983
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull driver core fixes from Greg KH:
"Here are two fixes for the driver core that resolve some reported
issues.
One is a regression from 4.0, the other a fixes a reported oops that
has been there since 3.19.
Both have been in linux-next for a while with no problems"
* tag 'driver-core-4.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
drivers/base: cacheinfo: handle absence of caches
drivers: of/base: move of_init to driver_init
|
|
Pull perf fixes from Ingo Molnar:
"The biggest chunk of the changes are two regression fixes: a HT
workaround fix and an event-group scheduling fix. It's been verified
with 5 days of fuzzer testing.
Other fixes:
- eBPF fix
- a BIOS breakage detection fix
- PMU driver fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel/pt: Fix a refactoring bug
perf/x86: Tweak broken BIOS rules during check_hw_exists()
perf/x86/intel/pt: Untangle pt_buffer_reset_markers()
perf: Disallow sparse AUX allocations for non-SG PMUs in overwrite mode
perf/x86: Improve HT workaround GP counter constraint
perf/x86: Fix event/group validation
perf: Fix race in BPF program unregister
|
|
Add the following helpers:
1. mlx5_query_port_proto_oper -- queries the port speed port mask
2. mlx5_query_port_link_width_oper - queries the port link with bitmask
3. mlx5_query_port_vl_hw_cap - queries the Virtual Lanes supported on this port
These helpers will be used from the IB driver when working in ISSI > 0 mode.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Until now, mlx5_query_port_ptys always queried port number one.
Added new argument in the function's prototype so we can also query
the second port. This will be needed when thr helper will be invoked
from the IB driver on non FPP (Function-Per-Port) devices.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extend the function prototypes for max and operational mtu to take the
local port number. In the Ethernet driver is this hard coded to one,
since ConnectX4 Ethernet devices are always function-per-port.
The IB driver also serves older devices (ConnectIB) which isn't such,
and hence the part can vary.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add two wrapper functions to the query adapter command:
1. mlx5_query_board_id -- replaces the old mlx5_cmd_query_adapter.
2. mlx5_core_query_vendor_id -- retrieves the vendor_id from the
query_adapter command.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added the implementation for the following commands:
1. QUERY_HCA_VPORT_GID
2. QUERY_HCA_VPORT_PKEY
3. QUERY_HCA_VPORT_CONTEXT
They will be needed when we move to work with ISSI > 0 in the IB driver too.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the vport header file to be under include/linux/mlx5, such that
the mlx5 IB can use it as well.
Also add nic_ prefix to the vport NIC commands to differeniate between
HCA vport commands and NIC vport commands.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When working in ISSI > 0 mode, the model exposed by the device for
XRCs and SRQs is different. XRCs use XRC SRQs and plain SRQs are based
on RPM (Receive Memory Pool).
Add helper functions to create, modify, query, and arm XRC SRQs and RMPs.
Signed-off-by: Haggai Abramovsky <hagaya@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In flow dissector if an MPLS header contains an entropy label this is
saved in the new keyid field of flow_keys. The entropy label is
then represented in the flow hash function input.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In flow dissector if a GRE header contains a keyid this is saved in the
new keyid field of flow_keys. The GRE keyid is then represented
in the flow hash function input.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In flow_dissector set the flow label in flow_keys for IPv6. This also
removes the shortcircuiting of flow dissection when a non-zero label
is present, the flow label can be considered to provide additional
entropy for a hash.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In flow_dissector set vlan_id in flow_keys when VLAN is found.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We don't need to return the IPv6 address hash as part of flow keys.
In general, using the IPv6 address hash is risky in a hash value
since the underlying use of xor provides no entropy. If someone
really needs the hash value they can get it from the full IPv6
addresses in flow keys (e.g. from flow_get_u32_src).
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a new flow key for TIPC addresses.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds full IPv6 addresses into flow_keys and uses them as
input to the flow hash function. The implementation supports either
IPv4 or IPv6 addresses in a union, and selector is used to determine
how may words to input to jhash2.
We also add flow_get_u32_dst and flow_get_u32_src functions which are
used to get a u32 representation of the source and destination
addresses. For IPv6, ipv6_addr_hash is called. These functions retain
getting the legacy values of src and dst in flow_keys.
With this patch, Ethertype and IP protocol are now included in the
flow hash input.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch changes flow hashing to use jhash2 over the flow_keys
structure instead just doing jhash_3words over src, dst, and ports.
This method will allow us take more input into the hashing function
so that we can include full IPv6 addresses, VLAN, flow labels etc.
without needing to resort to xor'ing which makes for a poor hash.
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add uapi define for MPLS over IP.
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Kalle Valo says:
====================
new driver mt7601u for MediaTek Wi-Fi devices MT7601U
ath10k:
* qca6174 power consumption improvements, enable ASPM etc (Michal)
wil6210:
* support Wi-Fi Simple Configuration in STA mode
iwlwifi:
* a few fixes (re-enablement of interrupts for certain new
platforms that have special power states)
* Rework completely the RBD allocation model towards new
multi RX hardware.
* cleanups
* scan reworks continuation (Luca)
mwifiex:
* improve firmware debug functionality
rtlwifi:
* update regulatory database
brcmfmac:
* cleanup and new feature support in PCIe code
* alternative nvram loading for router support
====================
Conflicts:
drivers/net/wireless/iwlwifi/Kconfig
Trivial conflict in iwlwifi Kconfig, two commits adding
the same two chip numbers to the help text, but order
transposed.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow eBPF programs attached to classifier/actions to call
bpf_clone_redirect(skb, ifindex, flags) helper which will
mirror or redirect the packet by dynamic ifindex selection
from within the program to a target device either at ingress
or at egress. Can be used for various scenarios, for example,
to load balance skbs into veths, split parts of the traffic
to local taps, etc.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the TI dp83867 Gigabit ethernet phy
device.
The DP83867 is a robust, low power, fully featured
Physical Layer transceiver with integrated PMD
sublayers to support 10BASE-T, 100BASE-TX and
1000BASE-T Ethernet protocols.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull block layer fixes from Jens Axboe:
"Sending this off now, as I'm not aware of other current bugs, nor do I
expect further fixes before 4.1 final. This contains two fixes:
- a fix for a bdi unregister warning that gets spewed on md, due to a
regression introduced earlier in this cycle. From Neil Brown.
- a fix for a compile warning for NVMe on 32-bit platforms, also a
regression introduced in this cycle. From Arnd Bergmann"
* 'for-linus' of git://git.kernel.dk/linux-block:
NVMe: fix type warning on 32-bit
block: discard bdi_unregister() in favour of bdi_destroy()
|
|
The naming convention is to always have the flags prefixed with
IEEE80211_HW_ so they're 'namespaced', make this flag follow it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There are no drivers setting IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE
or IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE, so any code using the
two flags is dead; it's also exceedingly unlikely that any new driver
could ever need to set these flags.
The wcn36xx code is almost certainly broken, but this preserves the
previous behaviour.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Even if the pointers are really only accessible to root and used
pretty much only by wpa_supplicant, this is still not great; even
for debugging it'd be easier to have something that's easier to
read and guaranteed to never get reused.
With the recent change to make mac80211 create an ack_skb for the
mgmt-tx path this becomes possible, only the client probe method
needs to also allocate an ack_skb, and we can store the cookie in
that skb.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
For drivers supporting TSO or similar features, but that still have
PN assignment in software, there's a need to have some memory to
store the current PN value. As mac80211 already stores this and it's
somewhat complicated to add a per-driver area to the key struct (due
to the dynamic sizing thereof) it makes sense to just move the TX PN
to the keyconf, i.e. the public part of the key struct.
As TKIP is more complicated and we won't able to offload it in this
way right now (fast-xmit is skipped for TKIP unless the HW does it
all, and our hardware needs MMIC calculation in software) I've not
moved that for now - it's possible but requires exposing a lot of
the internal TKIP state.
As an bonus side effect, we can remove a lot of code by assuming the
keyseq struct has a certain layout - with BUILD_BUG_ON to verify it.
This might also improve performance, since now TX and RX no longer
share a cacheline.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Conflicts:
drivers/net/phy/amd-xgbe-phy.c
drivers/net/wireless/iwlwifi/Kconfig
include/net/mac80211.h
iwlwifi/Kconfig and mac80211.h were both trivial overlapping
changes.
The drivers/net/phy/amd-xgbe-phy.c file got removed in 'net-next' and
the bug fix that happened on the 'net' side is already integrated
into the rest of the amd-xgbe driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) Various VTI tunnel (mark handling, PMTU) bug fixes from Alexander
Duyck and Steffen Klassert.
2) Revert ethtool PHY query change, it wasn't correct. The PHY address
selected by the driver running the PHY to MAC connection decides
what PHY address GET ethtool operations return information from.
3) Fix handling of sequence number bits for encryption IV generation in
ESP driver, from Herbert Xu.
4) UDP can return -EAGAIN when we hit a bad checksum on receive, even
when there are other packets in the receive queue which is wrong.
Just respect the error returned from the generic socket recv
datagram helper. From Eric Dumazet.
5) Fix BNA driver firmware loading on big-endian systems, from Ivan
Vecera.
6) Fix regression in that we were inheriting the congestion control of
the listening socket for new connections, the intended behavior
always was to use the default in this case. From Neal Cardwell.
7) Fix NULL deref in brcmfmac driver, from Arend van Spriel.
8) OTP parsing fix in iwlwifi from Liad Kaufman.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (26 commits)
vti6: Add pmtu handling to vti6_xmit.
Revert "net: core: 'ethtool' issue with querying phy settings"
bnx2x: Move statistics implementation into semaphores
xen: netback: read hotplug script once at start of day.
xen: netback: fix printf format string warning
Revert "netfilter: ensure number of counters is >0 in do_replace()"
net: dsa: Properly propagate errors from dsa_switch_setup_one
tcp: fix child sockets to use system default congestion control if not set
udp: fix behavior of wrong checksums
sfc: free multiple Rx buffers when required
bna: fix soft lock-up during firmware initialization failure
bna: remove unreasonable iocpf timer start
bna: fix firmware loading on big-endian machines
bridge: fix br_multicast_query_expired() bug
via-rhine: Resigning as maintainer
brcmfmac: avoid null pointer access when brcmf_msgbuf_get_pktid() fails
mac80211: Fix mac80211.h docbook comments
iwlwifi: nvm: fix otp parsing in 8000 hw family
iwlwifi: pcie: fix tracking of cmd_in_flight
ip_vti/ip6_vti: Preserve skb->mark after rcv_cb call
...
|
|
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Florian Westphal
Bernhard Thaler
Eric Dumazet
Saeed Mahameed
Hadar Hen Zion
Florian Fainelli
David S. Miller
Stephen Smalley
Johannes Berg
Jakub Kicinski
Oliver Hartkopp
Majd Dibbiny
Alexei Starovoitov
Linus Torvalds
Haggai Abramonvsky
Tom Herbert
Dan Murphy
John W. Linville