| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Since ra_chain is per-net, we may use per-net mutexes
to protect them in ip_ra_control(). This improves
scalability.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is optimization, which makes ip_call_ra_chain()
iterate less sockets to find the sockets it's looking for.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Define new netlink attributes for rmnet mux_id and flags. These
flags / mux_id were earlier using vlan flags / id respectively.
The flag bits are also moved to uapi and are renamed with
prefix RMNET_FLAG_*.
Also add the rmnet policy to handle the new netlink attributes.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently when tipc is unable to queue a received message on a
socket, the message is rejected back to the sender with error
TIPC_ERR_OVERLOAD. However, the application on this socket
has no knowledge about these discards.
In this commit, we try to step the sk_drops counter when tipc
is unable to queue a received message. Export sk_drops
using tipc socket diagnostics.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: GhantaKrishnamurthy MohanKrishna <mohan.krishna.ghanta.krishnamurthy@ericsson.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This commit adds socket diagnostics capability for AF_TIPC in netlink
family NETLINK_SOCK_DIAG in a new kernel module (diag.ko).
The following are key design considerations:
- config TIPC_DIAG has default y, like INET_DIAG.
- only requests with flag NLM_F_DUMP is supported (dump all).
- tipc_sock_diag_req message is introduced to send filter parameters.
- the response attributes are of TLV, some nested.
To avoid exposing data structures between diag and tipc modules and
avoid code duplication, the following additions are required:
- export tipc_nl_sk_walk function to reuse socket iterator.
- export tipc_sk_fill_sock_diag to fill the tipc diag attributes.
- create a sock_diag response message in __tipc_add_sock_diag defined
in diag.c and use the above exported tipc_sk_fill_sock_diag
to fill response.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: GhantaKrishnamurthy MohanKrishna <mohan.krishna.ghanta.krishnamurthy@ericsson.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
top_hierarchy arg can be determined by comparing parent_resource_id to
DEVLINK_RESOURCE_ID_PARENT_TOP so it does not need to be a separate
argument.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simon Wunderlich says:
====================
This feature/cleanup patchset includes the following patches:
- avoid redundant multicast TT entries, by Linus Luessing
- add netlink support for distributed arp table cache and multicast flags,
by Linus Luessing (2 patches)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This commit adds struct uevent_sock to struct net. Since struct uevent_sock
records the position of the uevent socket in the uevent socket list we can
trivially remove it from the uevent socket list during cleanup. This speeds
up the old removal codepath.
Note, list_del() will hit __list_del_entry_valid() in its call chain which
will validate that the element is a member of the list. If it isn't it will
take care that the list is not modified.
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-03-21
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Add a BPF hook for sendmsg and sendfile by reusing the ULP infrastructure
and sockmap. Three helpers are added along with this, bpf_msg_apply_bytes(),
bpf_msg_cork_bytes(), and bpf_msg_pull_data(). The first is used to tell
for how many bytes the verdict should be applied to, the second to tell
that x bytes need to be queued first to retrigger the BPF program for a
verdict, and the third helper is mainly for the sendfile case to pull in
data for making it private for reading and/or writing, from John.
2) Improve address to symbol resolution of user stack traces in BPF stackmap.
Currently, the latter stores the address for each entry in the call trace,
however to map these addresses to user space files, it is necessary to
maintain the mapping from these virtual addresses to symbols in the binary
which is not practical for system-wide profiling. Instead, this option for
the stackmap rather stores the ELF build id and offset for the call trace
entries, from Song.
3) Add support that allows BPF programs attached to perf events to read the
address values recorded with the perf events. They are requested through
PERF_SAMPLE_ADDR via perf_event_open(). Main motivation behind it is to
support building memory or lock access profiling and tracing tools with
the help of BPF, from Teng.
4) Several improvements to the tools/bpf/ Makefiles. The 'make bpf' in the
tools directory does not provide the standard quiet output except for
bpftool and it also does not respect specifying a build output directory.
'make bpf_install' command neither respects specified destination nor
prefix, all from Jiri. In addition, Jakub fixes several other minor issues
in the Makefiles on top of that, e.g. fixing dependency paths, phony
targets and more.
5) Various doc updates e.g. add a comment for BPF fs about reserved names
to make the dentry lookup from there a bit more obvious, and a comment
to the bpf_devel_QA file in order to explain the diff between native
and bpf target clang usage with regards to pointer size, from Quentin
and Daniel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, if a bpf sk msg program is run the program
can only parse data that the (start,end) pointers already
consumed. For sendmsg hooks this is likely the first
scatterlist element. For sendpage this will be the range
(0,0) because the data is shared with userspace and by
default we want to avoid allowing userspace to modify
data while (or after) BPF verdict is being decided.
To support pulling in additional bytes for parsing use
a new helper bpf_sk_msg_pull(start, end, flags) which
works similar to cls tc logic. This helper will attempt
to point the data start pointer at 'start' bytes offest
into msg and data end pointer at 'end' bytes offset into
message.
After basic sanity checks to ensure 'start' <= 'end' and
'end' <= msg_length there are a few cases we need to
handle.
First the sendmsg hook has already copied the data from
userspace and has exclusive access to it. Therefor, it
is not necessesary to copy the data. However, it may
be required. After finding the scatterlist element with
'start' offset byte in it there are two cases. One the
range (start,end) is entirely contained in the sg element
and is already linear. All that is needed is to update the
data pointers, no allocate/copy is needed. The other case
is (start, end) crosses sg element boundaries. In this
case we allocate a block of size 'end - start' and copy
the data to linearize it.
Next sendpage hook has not copied any data in initial
state so that data pointers are (0,0). In this case we
handle it similar to the above sendmsg case except the
allocation/copy must always happen. Then when sending
the data we have possibly three memory regions that
need to be sent, (0, start - 1), (start, end), and
(end + 1, msg_length). This is required to ensure any
writes by the BPF program are correctly transmitted.
Lastly this operation will invalidate any previous
data checks so BPF programs will have to revalidate
pointers after making this BPF call.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
In the case where we need a specific number of bytes before a
verdict can be assigned, even if the data spans multiple sendmsg
or sendfile calls. The BPF program may use msg_cork_bytes().
The extreme case is a user can call sendmsg repeatedly with
1-byte msg segments. Obviously, this is bad for performance but
is still valid. If the BPF program needs N bytes to validate
a header it can use msg_cork_bytes to specify N bytes and the
BPF program will not be called again until N bytes have been
accumulated. The infrastructure will attempt to coalesce data
if possible so in many cases (most my use cases at least) the
data will be in a single scatterlist element with data pointers
pointing to start/end of the element. However, this is dependent
on available memory so is not guaranteed. So BPF programs must
validate data pointer ranges, but this is the case anyways to
convince the verifier the accesses are valid.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
A single sendmsg or sendfile system call can contain multiple logical
messages that a BPF program may want to read and apply a verdict. But,
without an apply_bytes helper any verdict on the data applies to all
bytes in the sendmsg/sendfile. Alternatively, a BPF program may only
care to read the first N bytes of a msg. If the payload is large say
MB or even GB setting up and calling the BPF program repeatedly for
all bytes, even though the verdict is already known, creates
unnecessary overhead.
To allow BPF programs to control how many bytes a given verdict
applies to we implement a bpf_msg_apply_bytes() helper. When called
from within a BPF program this sets a counter, internal to the
BPF infrastructure, that applies the last verdict to the next N
bytes. If the N is smaller than the current data being processed
from a sendmsg/sendfile call, the first N bytes will be sent and
the BPF program will be re-run with start_data pointing to the N+1
byte. If N is larger than the current data being processed the
BPF verdict will be applied to multiple sendmsg/sendfile calls
until N bytes are consumed.
Note1 if a socket closes with apply_bytes counter non-zero this
is not a problem because data is not being buffered for N bytes
and is sent as its received.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
This implements a BPF ULP layer to allow policy enforcement and
monitoring at the socket layer. In order to support this a new
program type BPF_PROG_TYPE_SK_MSG is used to run the policy at
the sendmsg/sendpage hook. To attach the policy to sockets a
sockmap is used with a new program attach type BPF_SK_MSG_VERDICT.
Similar to previous sockmap usages when a sock is added to a
sockmap, via a map update, if the map contains a BPF_SK_MSG_VERDICT
program type attached then the BPF ULP layer is created on the
socket and the attached BPF_PROG_TYPE_SK_MSG program is run for
every msg in sendmsg case and page/offset in sendpage case.
BPF_PROG_TYPE_SK_MSG Semantics/API:
BPF_PROG_TYPE_SK_MSG supports only two return codes SK_PASS and
SK_DROP. Returning SK_DROP free's the copied data in the sendmsg
case and in the sendpage case leaves the data untouched. Both cases
return -EACESS to the user. Returning SK_PASS will allow the msg to
be sent.
In the sendmsg case data is copied into kernel space buffers before
running the BPF program. The kernel space buffers are stored in a
scatterlist object where each element is a kernel memory buffer.
Some effort is made to coalesce data from the sendmsg call here.
For example a sendmsg call with many one byte iov entries will
likely be pushed into a single entry. The BPF program is run with
data pointers (start/end) pointing to the first sg element.
In the sendpage case data is not copied. We opt not to copy the
data by default here, because the BPF infrastructure does not
know what bytes will be needed nor when they will be needed. So
copying all bytes may be wasteful. Because of this the initial
start/end data pointers are (0,0). Meaning no data can be read or
written. This avoids reading data that may be modified by the
user. A new helper is added later in this series if reading and
writing the data is needed. The helper call will do a copy by
default so that the page is exclusively owned by the BPF call.
The verdict from the BPF_PROG_TYPE_SK_MSG applies to the entire msg
in the sendmsg() case and the entire page/offset in the sendpage case.
This avoids ambiguity on how to handle mixed return codes in the
sendmsg case. Again a helper is added later in the series if
a verdict needs to apply to multiple system calls and/or only
a subpart of the currently being processed message.
The helper msg_redirect_map() can be used to select the socket to
send the data on. This is used similar to existing redirect use
cases. This allows policy to redirect msgs.
Pseudo code simple example:
The basic logic to attach a program to a socket is as follows,
// load the programs
bpf_prog_load(SOCKMAP_TCP_MSG_PROG, BPF_PROG_TYPE_SK_MSG,
&obj, &msg_prog);
// lookup the sockmap
bpf_map_msg = bpf_object__find_map_by_name(obj, "my_sock_map");
// get fd for sockmap
map_fd_msg = bpf_map__fd(bpf_map_msg);
// attach program to sockmap
bpf_prog_attach(msg_prog, map_fd_msg, BPF_SK_MSG_VERDICT, 0);
Adding sockets to the map is done in the normal way,
// Add a socket 'fd' to sockmap at location 'i'
bpf_map_update_elem(map_fd_msg, &i, fd, BPF_ANY);
After the above any socket attached to "my_sock_map", in this case
'fd', will run the BPF msg verdict program (msg_prog) on every
sendmsg and sendpage system call.
For a complete example see BPF selftests or sockmap samples.
Implementation notes:
It seemed the simplest, to me at least, to use a refcnt to ensure
psock is not lost across the sendmsg copy into the sg, the bpf program
running on the data in sg_data, and the final pass to the TCP stack.
Some performance testing may show a better method to do this and avoid
the refcnt cost, but for now use the simpler method.
Another item that will come after basic support is in place is
supporting MSG_MORE flag. At the moment we call sendpages even if
the MSG_MORE flag is set. An enhancement would be to collect the
pages into a larger scatterlist and pass down the stack. Notice that
bpf_tcp_sendmsg() could support this with some additional state saved
across sendmsg calls. I built the code to support this without having
to do refactoring work. Other features TBD include ZEROCOPY and the
TCP_RECV_QUEUE/TCP_NO_QUEUE support. This will follow initial series
shortly.
Future work could improve size limits on the scatterlist rings used
here. Currently, we use MAX_SKB_FRAGS simply because this was being
used already in the TLS case. Future work could extend the kernel sk
APIs to tune this depending on workload. This is a trade-off
between memory usage and throughput performance.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
The current implementation of sk_alloc_sg expects scatterlist to always
start at entry 0 and complete at entry MAX_SKB_FRAGS.
Future patches will want to support starting at arbitrary offset into
scatterlist so add an additional sg_start parameters and then default
to the current values in TLS code paths.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
When calling do_tcp_sendpages() from in kernel and we know the data
has no references from user side we can omit SKBTX_SHARED_FRAG flag.
This patch adds an internal flag, NO_SKBTX_SHARED_FRAG that can be used
to omit setting SKBTX_SHARED_FRAG.
The flag is not exposed to userspace because the sendpage call from
the splice logic masks out all bits except MSG_MORE.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
The TLS ULP module builds scatterlists from a sock using
page_frag_refill(). This is going to be useful for other ULPs
so move it into sock file for more general use.
In the process remove useless goto at end of while loop.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
use proc_remove_subtree() for subtree removal, both on setup failure
halfway through and on teardown. No need to make simple things
complex...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Publications for TIPC_CLUSTER_SCOPE and TIPC_ZONE_SCOPE are in all
aspects handled the same way, both on the publishing node and on the
receiving nodes.
Despite previous ambitions to the contrary, this is never going to change,
so we take the conseqeunce of this and obsolete TIPC_ZONE_SCOPE and related
macros/functions. Whenever a user is doing a bind() or a sendmsg() attempt
using ZONE_SCOPE we translate this internally to CLUSTER_SCOPE, while we
remain compatible with users and remote nodes still using ZONE_SCOPE.
Furthermore, the non-formalized scope value 0 has always been permitted
for use during lookup, with the same meaning as ZONE_SCOPE/CLUSTER_SCOPE.
We now permit it even as binding scope, but for compatibility reasons we
choose to not change the value of TIPC_CLUSTER_SCOPE.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds TCP_NLA_SND_SSTHRESH stat into SCM_TIMESTAMPING_OPT_STATS
that reports tcp_sock.snd_ssthresh.
Signed-off-by: Yousuk Seung <ysseung@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rtnl_lock() is widely used mutex in kernel. Some of kernel code
does memory allocations under it. In case of memory deficit this
may invoke OOM killer, but the problem is a killed task can't
exit if it's waiting for the mutex. This may be a reason of deadlock
and panic.
This patch adds a new primitive, which responds on SIGKILL, and
it allows to use it in the places, where we don't want to sleep
forever.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch moves the udp_rmem_min, udp_wmem_min
to namespace and init the udp_l3mdev_accept explicitly.
The udp_rmem_min/udp_wmem_min affect udp rx/tx queue,
with this patch namespaces can set them differently.
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ipv6_chk_addr_and_flags determines if an address is a local address and
optionally if it is an address on a specific device. For example, it is
called by ip6_route_info_create to determine if a given gateway address
is a local address. The address check currently does not consider L3
domains and as a result does not allow a route to be added in one VRF
if the nexthop points to an address in a second VRF. e.g.,
$ ip route add 2001:db8:1::/64 vrf r2 via 2001:db8:102::23
Error: Invalid gateway address.
where 2001:db8:102::23 is an address on an interface in vrf r1.
ipv6_chk_addr_and_flags needs to allow callers to always pass in a device
with a separate argument to not limit the address to the specific device.
The device is used used to determine the L3 domain of interest.
To that end add an argument to skip the device check and update callers
to always pass a device where possible and use the new argument to mean
any address in the domain.
Update a handful of users of ipv6_chk_addr with a NULL dev argument. This
patch handles the change to these callers without adding the domain check.
ip6_validate_gw needs to handle 2 cases - one where the device is given
as part of the nexthop spec and the other where the device is resolved.
There is at least 1 VRF case where deferring the check to only after
the route lookup has resolved the device fails with an unintuitive error
"RTNETLINK answers: No route to host" as opposed to the preferred
"Error: Gateway can not be a local address." The 'no route to host'
error is because of the fallback to a full lookup. The check is done
twice to avoid this error.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, bpf stackmap store address for each entry in the call trace.
To map these addresses to user space files, it is necessary to maintain
the mapping from these virtual address to symbols in the binary. Usually,
the user space profiler (such as perf) has to scan /proc/pid/maps at the
beginning of profiling, and monitor mmap2() calls afterwards. Given the
cost of maintaining the address map, this solution is not practical for
system wide profiling that is always on.
This patch tries to solve this problem with a variation of stackmap. This
variation is enabled by flag BPF_F_STACK_BUILD_ID. Instead of storing
addresses, the variation stores ELF file build_id + offset.
Build ID is a 20-byte unique identifier for ELF files. The following
command shows the Build ID of /bin/bash:
[user@]$ readelf -n /bin/bash
...
Build ID: XXXXXXXXXX
...
With BPF_F_STACK_BUILD_ID, bpf_get_stackid() tries to parse Build ID
for each entry in the call trace, and translate it into the following
struct:
struct bpf_stack_build_id_offset {
__s32 status;
unsigned char build_id[BPF_BUILD_ID_SIZE];
union {
__u64 offset;
__u64 ip;
};
};
The search of build_id is limited to the first page of the file, and this
page should be in page cache. Otherwise, we fallback to store ip for this
entry (ip field in struct bpf_stack_build_id_offset). This requires the
build_id to be stored in the first page. A quick survey of binary and
dynamic library files in a few different systems shows that almost all
binary and dynamic library files have build_id in the first page.
Build_id is only meaningful for user stack. If a kernel stack is added to
a stackmap with BPF_F_STACK_BUILD_ID, it will automatically fallback to
only store ip (status == BPF_STACK_BUILD_ID_IP). Similarly, if build_id
lookup failed for some reason, it will also fallback to store ip.
User space can access struct bpf_stack_build_id_offset with bpf
syscall BPF_MAP_LOOKUP_ELEM. It is necessary for user space to
maintain mapping from build id to binary files. This mostly static
mapping is much easier to maintain than per process address maps.
Note: Stackmap with build_id only works in non-nmi context at this time.
This is because we need to take mm->mmap_sem for find_vma(). If this
changes, we would like to allow build_id lookup in nmi context.
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
This patch is to add SCTP_AUTH_NO_AUTH type for AUTHENTICATION_EVENT,
as described in section 6.1.8 of RFC6458.
SCTP_AUTH_NO_AUTH: This report indicates that the peer does not
support SCTP authentication as defined in [RFC4895].
Note that the implementation is quite similar as that of
SCTP_ADAPTATION_INDICATION.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to add SCTP_AUTH_FREE_KEY type for AUTHENTICATION_EVENT,
as described in section 6.1.8 of RFC6458.
SCTP_AUTH_FREE_KEY: This report indicates that the SCTP
implementation will no longer use the key identifier specified
in auth_keynumber.
After deactivating a key, it would never be used again, which means
it's refcnt can't be held/increased by new chunks. But there may be
some chunks in out queue still using it. So only when refcnt is 1,
which means no chunk in outqueue is using/holding this key either,
this EVENT would be sent.
When users receive this notification, they could do DEL_KEY sockopt to
remove this shkey, and also tell the peer that this key won't be used
in any chunk thoroughly from now on, then the peer can remove it as
well safely.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to add sockopt SCTP_AUTH_DEACTIVATE_KEY, as described in
section 8.3.4 of RFC6458.
This set option indicates that the application will no longer send user
messages using the indicated key identifier.
Note that RFC requires that only deactivated keys that are no longer used
by an association can be deleted, but for the backward compatibility, it
is not to check deactivated when deleting or replacing one sh_key.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to add support for SCTP AUTH Information for sendmsg,
as described in section 5.3.8 of RFC6458.
With this option, you can provide shared key identifier used for
sending the user message.
It's also a necessary send info for sctp_sendv.
Note that it reuses sinfo->sinfo_tsn to indicate if this option is
set and sinfo->sinfo_ssn to save the shkey ID which can be 0.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With refcnt support for sh_key, chunks auth sh_keys can be decided
before enqueuing it. Changing the active key later will not affect
the chunks already enqueued.
Furthermore, this is necessary when adding the support for authinfo
for sendmsg in next patch.
Note that struct sctp_chunk can't be grown due to that performance
drop issue on slow cpu, so it just reuses head_skb memory for shkey
in sctp_chunk.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Dump the list of multicast flags entries via the netlink socket.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
Dump the list of DAT cache entries via the netlink socket.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The new variable is only available when CONFIG_SYSCTL is enabled,
otherwise we get a link error:
net/ipv4/ip_tunnel.o: In function `ip_tunnel_init_net':
ip_tunnel.c:(.text+0x278b): undefined reference to `sysctl_fb_tunnels_only_for_init_net'
net/ipv6/sit.o: In function `sit_init_net':
sit.c:(.init.text+0x4c): undefined reference to `sysctl_fb_tunnels_only_for_init_net'
net/ipv6/ip6_tunnel.o: In function `ip6_tnl_init_net':
ip6_tunnel.c:(.init.text+0x39): undefined reference to `sysctl_fb_tunnels_only_for_init_net'
This adds an extra condition, keeping the traditional behavior when
CONFIG_SYSCTL is disabled.
Fixes: 79134e6ce2c9 ("net: do not create fallback tunnels for non-default namespaces")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make locking scheme be visible for users, and provide
a comment what for we are need exit_batch() methods,
and when it should be used.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to abstract away access to the
ipv6.sysctl.multipath_hash_policy variable, which is not available on
systems compiled without IPv6 support, introduce a wrapper function
ip6_multipath_hash_policy() that falls back to 0 on non-IPv6 systems.
Use this wrapper from mlxsw/spectrum_router instead of a direct
reference.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some network devices - notably ipvlan slave - are not compatible with
any kind of rx_handler. Currently the hook can be installed but any
configuration (bridge, bond, macsec, ...) is nonfunctional.
This change allocates a priv_flag bit to mark such devices and explicitly
forbid installing a rx_handler if such bit is set. The new bit is used
by ipvlan slave device.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a new callback in tc_action_ops, it will be needed by the tc actions
to compute its size when a ADD/DELETE notification message is constructed.
This routine has to take into account optional/variable size TLVs specific
per action.
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce a new function argument to carry total attributes size for
correct allocation of skb in event messages.
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
fallback tunnels (like tunl0, gre0, gretap0, erspan0, sit0,
ip6tnl0, ip6gre0) are automatically created when the corresponding
module is loaded.
These tunnels are also automatically created when a new network
namespace is created, at a great cost.
In many cases, netns are used for isolation purposes, and these
extra network devices are a waste of resources. We are using
thousands of netns per host, and hit the netns creation/delete
bottleneck a lot. (Many thanks to Kirill for recent work on this)
Add a new sysctl so that we can opt-out from this automatic creation.
Note that these tunnels are still created for the initial namespace,
to be the least intrusive for typical setups.
Tested:
lpk43:~# cat add_del_unshare.sh
for i in `seq 1 40`
do
(for j in `seq 1 100` ; do unshare -n /bin/true >/dev/null ; done) &
done
wait
lpk43:~# echo 0 >/proc/sys/net/core/fb_tunnels_only_for_init_net
lpk43:~# time ./add_del_unshare.sh
real 0m37.521s
user 0m0.886s
sys 7m7.084s
lpk43:~# echo 1 >/proc/sys/net/core/fb_tunnels_only_for_init_net
lpk43:~# time ./add_del_unshare.sh
real 0m4.761s
user 0m0.851s
sys 1m8.343s
lpk43:~#
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We use a two-step process to configure a filter with RSS spreading. First,
the RSS context is allocated and configured using ETHTOOL_SRSSH; this
returns an identifier (rss_context) which can then be passed to subsequent
invocations of ETHTOOL_SRXCLSRLINS to specify that the offset from the RSS
indirection table lookup should be added to the queue number (ring_cookie)
when delivering the packet. Drivers for devices which can only use the
indirection table entry directly (not add it to a base queue number)
should reject rule insertions combining RSS with a nonzero ring_cookie.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Saeed Mahameed says:
====================
mlx5-updates-2018-02-28-2 (IPSec-2)
This series follows our previous one to lay out the foundations for IPSec
in user-space and extend current kernel netdev IPSec support. As noted in
our previous pull request cover letter "mlx5-updates-2018-02-28-1 (IPSec-1)",
the IPSec mechanism will be supported through our flow steering mechanism.
Therefore, we need to change the initialization order. Furthermore, IPsec
is also supported in both egress and ingress. Since our current flow
steering is egress only, we add an empty (only implemented through FPGA
steering ops) egress namespace to handle that case. We also implement
the required flow steering callbacks and logic in our FPGA driver.
We extend the FPGA support for ESN and modifying a xfrm too. Therefore, we
add support for some new FPGA command interface that supports them. The
other required bits are added too. The new features and requirements are
advertised via cap bits.
Last but not least, we revise our driver's accel_esp API. This API will be
shared between our netdev and IB driver, so we need to have all the required
functionality from both worlds.
Regards,
Aviad and Matan
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow setting firstfrag as matching option in tc flower classifier.
# tc filter add dev eth0 protocol ip parent ffff: \
flower indev eth0 \
ip_flags firstfrag
action mirred egress redirect dev eth1
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This commit adds new field "addr" to bpf_perf_event_data which could be
read and used by bpf programs attached to perf events. The value of the
field is copied from bpf_perf_event_data_kern.addr and contains the
address value recorded by specifying sample_type with PERF_SAMPLE_ADDR
when calling perf_event_open.
Signed-off-by: Teng Qin <qinteng@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Currently ESN is not supported with IPSec device offload.
This patch adds ESN support to IPsec device offload.
Implementing new xfrm device operation to synchronize offloading device
ESN with xfrm received SN. New QP command to update SA state at the
following:
ESN 1 ESN 2 ESN 3
|-----------*-----------|-----------*-----------|-----------*
^ ^ ^ ^ ^ ^
^ - marks where QP command invoked to update the SA ESN state
machine.
| - marks the start of the ESN scope (0-2^32-1). At this point move SA
ESN overlap bit to zero and increment ESN.
* - marks the middle of the ESN scope (2^31). At this point move SA
ESN overlap bit to one.
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Yossef Efraim <yossefe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
In order to add a context to the FPGA, we need to get both the software
transform context (which includes the keys, etc) and the
source/destination IPs (which are included in the steering
rule). Therefore, we register new set of firmware like commands for
the FPGA. Each time a rule is added, the steering core infrastructure
calls the FPGA command layer. If the rule is intended for the FPGA,
it combines the IPs information with the software transformation
context and creates the respective hardware transform.
Afterwards, it calls the standard steering command layer.
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The current code has one layer that executed FPGA commands and
the Ethernet part directly used this code. Since downstream patches
introduces support for IPSec in mlx5_ib, we need to provide some
abstractions. This patch refactors the accel code into one layer
that creates a software IPSec transformation and another one which
creates the actual hardware context.
The internal command implementation is now hidden in the FPGA
core layer. The code also adds the ability to share FPGA hardware
contexts. If two contexts are the same, only a reference count
is taken.
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Currently our device requires additional metadata in packet
to perform ipsec crypto offload.
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
We will need that for ipsec verbs.
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
This patch adds V2 command support.
New fpga devices support extended features (udp encap, esn etc...), this
features require new hardware sadb format therefore we have a new version
of commands to manipulate it.
Signed-off-by: Yossef Efraim <yossefe@mellanox.com>
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Current hardware decrypts and authenticates incoming ESP packets.
Subsequently, the software extracts the nexthdr field, truncates the
trailer and adjusts csum accordingly.
With this patch and a capable device, the trailer is being removed
by the hardware and the nexthdr field is conveyed via PET. This way
we avoid both the need to access the trailer (cache miss) and to
compute its relative checksum, which significantly improve
the performance.
Experiment shows that trailer removal improves the performance by
2Gbps, (netperf). Both forwarding and host-to-host configurations.
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The current code assume only SA QP commands.
Refactor in order to pave the way for new QP commands:
1. Generic cmd response format.
2. SA cmd checks are in dedicated functions.
3. Aligned debug prints.
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Saeed Mahameed says:
====================
mlx5-updates-2018-02-28-1 (IPSec-1)
This series consists of some fixes and refactors for the mlx5 drivers,
especially around the FPGA and flow steering. Most of them are trivial
fixes and are the foundation of allowing IPSec acceleration from user-space.
We use flow steering abstraction in order to accelerate IPSec packets.
When a user creates a steering rule, [s]he states that we'll carry an
encrypt/decrypt flow action (using a specific configuration) for every
packet which conforms to a certain match. Since currently offloading these
packets is done via FPGA, we'll add another set of flow steering ops.
These ops will execute the required FPGA commands and then call the
standard steering ops.
In order to achieve this, we need that the commands will get all the
required information. Therefore, we pass the fte object and embed the
flow_action struct inside the fte. In addition, we add the shim layer
that will later be used for alternating between the standard and the
FPGA steering commands.
Some fixes, like " net/mlx5e: Wait for FPGA command responses with a timeout"
are very relevant for user-space applications, as these applications could
be killed, but we still want to wait for the FPGA and update the kernel's
database.
Regards,
Aviad and Matan
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Kirill Tkhai
Subash Abhinov Kasiviswanathan
GhantaKrishnamurthy MohanKrishna
David Ahern
David S. Miller
Christian Brauner
John Fastabend
Al Viro
Jon Maloy
Yousuk Seung
Tonghao Zhang
Song Liu
Xin Long
Linus Lüssing
Arnd Bergmann
Petr Machata
Paolo Abeni
Roman Mashak
Eric Dumazet
Edward Cree
Pieter Jansen van Vuuren
Teng Qin
Aviad Yehezkel
Yossi Kuperman