| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This patch is a follow up to patch 1 regarding "Selective Sub Address
matching with call user data". It allows use of the Fast-Select-Acceptance
optional user facility for X.25.
This patch just implements fast select with no restriction on response
(NRR). What this means (according to ITU-T Recomendation 10/96 section
6.16) is that if in an incoming call packet, the relevant facility bits are
set for fast-select-NRR, then the called DTE can issue a direct response to
the incoming packet using a call-accepted packet that contains
call-user-data. This patch allows such a response.
The called DTE can also respond with a clear-request packet that contains
call-user-data. However, this feature is currently not implemented by the
patch.
How is Fast Select Acceptance used?
By default, the system does not allow fast select acceptance (as before).
To enable a response to fast select acceptance,
After a listen socket in created and bound as follows
socket(AF_X25, SOCK_SEQPACKET, 0);
bind(call_soc, (struct sockaddr *)&locl_addr, sizeof(locl_addr));
but before a listen system call is made, the following ioctl should be used.
ioctl(call_soc,SIOCX25CALLACCPTAPPRV);
Now the listen system call can be made
listen(call_soc, 4);
After this, an incoming-call packet will be accepted, but no call-accepted
packet will be sent back until the following system call is made on the socket
that accepts the call
ioctl(vc_soc,SIOCX25SENDCALLACCPT);
The network (or cisco xot router used for testing here) will allow the
application server's call-user-data in the call-accepted packet,
provided the call-request was made with Fast-select NRR.
Signed-off-by: Shaun Pereira <spereira@tusc.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
From: Shaun Pereira <spereira@tusc.com.au>
This is the first (independent of the second) patch of two that I am
working on with x25 on linux (tested with xot on a cisco router). Details
are as follows.
Current state of module:
A server using the current implementation (2.6.11.7) of the x25 module will
accept a call request/ incoming call packet at the listening x.25 address,
from all callers to that address, as long as NO call user data is present
in the packet header.
If the server needs to choose to accept a particular call request/ incoming
call packet arriving at its listening x25 address, then the kernel has to
allow a match of call user data present in the call request packet with its
own. This is required when multiple servers listen at the same x25 address
and device interface. The kernel currently matches ALL call user data, if
present.
Current Changes:
This patch is a follow up to the patch submitted previously by Andrew
Hendry, and allows the user to selectively control the number of octets of
call user data in the call request packet, that the kernel will match. By
default no call user data is matched, even if call user data is present.
To allow call user data matching, a cudmatchlength > 0 has to be passed
into the kernel after which the passed number of octets will be matched.
Otherwise the kernel behavior is exactly as the original implementation.
This patch also ensures that as is normally the case, no call user data
will be present in the Call accepted / call connected packet sent back to
the caller
Future Changes on next patch:
There are cases however when call user data may be present in the call
accepted packet. According to the X.25 recommendation (ITU-T 10/96)
section 5.2.3.2 call user data may be present in the call accepted packet
provided the fast select facility is used. My next patch will include this
fast select utility and the ability to send up to 128 octets call user data
in the call accepted packet provided the fast select facility is used. I
am currently testing this, again with xot on linux and cisco.
Signed-off-by: Shaun Pereira <spereira@tusc.com.au>
(With a fix from Alexey Dobriyan <adobriyan@gmail.com>)
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch provides support for registering multiple netpoll clients to the
same network device. Only one of these clients may register an rx_hook,
however. In practice, this restriction has not been problematic. It is
worth mentioning, though, that the current design can be easily extended to
allow for the registration of multiple rx_hooks.
The basic idea of the patch is that the rx_np pointer in the netpoll_info
structure points to the struct netpoll that has rx_hook filled in. Aside
from this one case, there is no need for a pointer from the struct
net_device to an individual struct netpoll.
A lock is introduced to protect the setting and clearing of the np_rx
pointer. The pointer will only be cleared upon netpoll client module
removal, and the lock should be uncontested.
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch introduces a netpoll_info structure, which the struct net_device
will now point to instead of pointing to a struct netpoll. The reason for
this is two-fold: 1) fields such as the rx_flags, poll_owner, and poll_lock
should be maintained per net_device, not per netpoll; and 2) this is a first
step in providing support for multiple netpoll clients to register against the
same net_device.
The struct netpoll is now pointed to by the netpoll_info structure. As
such, the previous behaviour of the code is preserved.
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This trivial patch moves the assignment of poll_owner to -1 inside of
the lock. This fixes a potential SMP race in the code.
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patch just changes the order of structure members.
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
Control Midlevel
Add const prefix to snd_kcontrol_new_t pointer for better protection.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
HDSPM driver,PCI drivers,RME9652 driver
Added RME Hammerfall DSP MADI driver by Winfried Ritsch.
(Moved from alsa-driver tree to mainline.)
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
AC97 Codec,ATIIXP driver,VIA82xx driver
To avoid confusion, the structure members vendor/device were renamed
to subvendor/subdevice, because we compare them with PCI subsystem vendor
and subsystem device.
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
|
|
Add support for Maxim/Dallas DS1374 Real-Time Clock Chip
This change adds support for the Maxim/Dallas DS1374 RTC chip. This chip
is an I2C-based RTC that maintains a simple 32-bit binary seconds count
with battery backup support.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch renames the new linux/i2c-sysfs.h header file to
linux/hwmon-sysfs.h. This names seems to be more appropriate since this
file defines macros and structures not related to i2c but to hardware
monitoring drivers. The patch also updates the five hardware monitoring
driver which include that header file already.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This adds an I2C driver for the TPS6501x series of power management chips.
It's used on many OMAP based boards, and this driver has been widely used
in the Linux-OMAP trees over the last year or so.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Adds conversion from VID (mV) to register value. Used by the atxp1 I2C module.
Removed uneeded switch case.
Signed-off-by: Sebastian Witt <se.witt@gmx.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Some months ago, you killed the address ranges mechanism from all
sensors i2c chip drivers (both the module parameters and the in-code
address lists). I think it was a very good move, as the ranges can
easily be replaced by individual addresses, and this allowed for
significant cleanups in the i2c core (let alone the impressive size
shrink for all these drivers).
Unfortunately you did not do the same for non-sensors i2c chip drivers.
These need the address ranges even less, so we could get rid of the
ranges here as well for another significant i2c core cleanup. Here comes
a patch which does just that. Since the process is exactly the same as
what you did for the other drivers set already, I did not split this one
in parts.
A documentation update is included.
The change saves 308 bytes in the i2c core, and an average 1382 bytes
for chip drivers which use I2C_CLIENT_INSMOD, 126 bytes for those which
do not.
This change is required if we want to merge the sensors and non-sensors
i2c code (and we want to do this).
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Index: gregkh-2.6/Documentation/i2c/writing-clients
===================================================================
|
|
1/ Must typecast int to (sector_t) before inverting or we
might not invert enough bits.
2/ When "bitmap_offset" was added to mdp_superblock_1, we didn't increase
the count of words-used (96 to 100).
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
currently, md updates all superblocks (one on each device) in series. It
waits for one write to complete before starting the next. This isn't a big
problem as superblock updates don't happen that often.
However it is neater to do it in parallel, and if the drives in the array have
gone to "sleep" after a period of idleness, then waking them is parallel is
faster (and someone else should be worrying about power drain).
Futher, we will need parallel superblock updates for a future patch which
keeps the intent-logging bitmap near the superblock.
Also remove the silly code that retired superblock updates 100 times. This
simply never made sense.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This provides an alternate to storing the bitmap in a separate file. The
bitmap can be stored at a given offset from the superblock. Obviously the
creator of the array must make sure this doesn't intersect with data....
After is good for version-0.90 superblocks.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Before completing a 'write' the md superblock might need to be updated.
This is best done by the md_thread.
The current code schedules this up and queues the write request for later
handling by the md_thread.
However some personalities (Raid5/raid6) will deadlock if the md_thread
tries to submit requests to its own array.
So this patch changes things so the processes submitting the request waits
for the superblock to be written and then submits the request itself.
This fixes a recently-created deadlock in raid5/raid6
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
When an array is degraded, bit in the intent-bitmap are never cleared. So if
a recently failed drive is re-added, we only need to reconstruct the block
that are still reflected in the bitmap.
This patch adds support for this re-adding.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Currently we don't wait for updates to the bitmap to be flushed to disk
properly. The infrastructure all there, but it isn't being used....
A separate kernel thread (bitmap_writeback_daemon) is needed to wait for each
page as we cannot get callbacks when a page write completes.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
With this patch, the intent to write to some block in the array can be logged
to a bitmap file. Each bit represents some number of sectors and is set
before any update happens, and only cleared when all writes relating to all
sectors are complete.
After an unclean shutdown, information in this bitmap can be used to optimise
resync - only sectors which could be out-of-sync need to be updated.
Also if a drive is removed and then added back into an array, the recovery can
make use of the bitmap to optimise reconstruction. This is not implemented in
this patch.
Currently the bitmap is stored in a file which must (obviously) be stored on a
separate device.
The patch only provided infrastructure. It does not update any personalities
to bitmap intent logging.
Md arrays can still be used with no bitmap file. This patch has minimal
impact on such arrays.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
1/ change the return value (which is number-of-sectors synced)
from 'int' to 'sector_t'.
The number of sectors is usually easily small enough to fit
in an int, but if resync needs to abort, it may want to return
the total number of remaining sectors, which could be large.
Also errors cannot be returned as negative numbers now, so use
0 instead
2/ Add a 'skipped' return parameter to allow the array to report
that it skipped the sectors. This allows md to take this into account
in the speed calculations.
Currently there is no important skipping, but the bitmap-based-resync
that is coming will use this.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
When md marks the superblock dirty before a write, it calls
generic_make_request (to write the superblock) from within
generic_make_request (to write the first dirty block), which could cause
problems later.
With this patch, the superblock write is always done by the helper thread, and
write request are delayed until that write completes.
Also, the locking around marking the array dirty and writing the superblock is
improved to avoid possible races.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Shrink the stack when calling the drawing alignment functions.
Signed-off-by: James Simmons <jsimmons@www.infradead.org>
Cc: "Antonino A. Daplas" <adaplas@hotpop.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Improve the fonts for use with the framebuffer.
I've added all the characters marked 'FIXME' in the sun12x22 font and
created a 10x18 font (based on the sun12x22 font) and a 7x14 font (based
on the vga8x16 font).
This patch is non-intrusive, no options are enabled by default so most
users won't notice a thing.
I am placing my changes under the GPL, however, I've not seen any copyright
notices on the sun12x22 font and the vga8x16 font which I derived my new
fonts from so I don't know what the copyright status is.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Patch adds pci ID for CT 69000 chipset.
Signed-off-by: James Simmons <jsimmons@www.infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Add support for the Arc monochrome LCD board.
The board uses KS108 controllers to drive individual 64x64 LCD matrices.
The board can be paneled in a variety of setups such as 2x1=128x64,
4x4=256x256 and so on. The board/host interface is through GPIO.
Signed-off-by: Jaya Kumar <jayalk@intworks.biz>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: <linux-fbdev-devel@lists.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Since no one is using the inbuf, outbuf of struct fb_pixmap I removed their
use in the framebuffer console. The idea is instead move the pixmap
functionality below the accelerated functions intead of on top as the way
it is now. If there is no objection please apply. This is against Linus
latestr GIT tree. Thank you.
Signed-off-by: James Simmons <jsimmons@www.infradead.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
With Chris Wedgwood <cw@f00f.org>
As suggested by Chris, we can make the "just added" method ->release
conditional to UML only (better: to archs requesting it, i.e. only UML
currently), so that other archs don't get this unneeded crud, and if UML
won't need it any more we can kill this.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
CC: Ingo Molnar <mingo@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
With Chris Wedgwood <cw@f00f.org>
Currently UML must explicitly call the UML-specific
free_irq_by_irq_and_dev() for each free_irq call it's done.
This is needed because ->shutdown and/or ->disable are only called when the
last "action" for that irq is removed.
Instead, for UML shared IRQs (UML IRQs are very often, if not always,
shared), for each dev_id some setup is done, which must be cleared on the
release of that fd. For instance, for each open console a new instance
(i.e. new dev_id) of the same IRQ is requested().
Exactly, a fd is stored in an array (pollfds), which is after read by a
host thread and passed to poll(). Each event registered by poll() triggers
an interrupt. So, for each free_irq() we must remove the corresponding
host fd from the table, which we do via this -release() method.
In this patch we add an appropriate hook for this, and remove all uses of
it by pointing the hook to the said procedure; this is safe to do since the
said procedure.
Also some cosmetic improvements are included.
This is heavily based on some work by Chris Wedgwood, which however didn't
get the patch merged for something I'd call a "misunderstanding" (the need
for this patch wasn't cleanly explained, thus adding the generic hook was
felt as undesirable).
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
CC: Ingo Molnar <mingo@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The current include/asm-m32r/div64.h of 2.6.12-rc5 looks buggy. Here is a
patch for updating it to use asm-generic/div64.h for m32r like other
architectures.
Signed-off-by: Hitoshi Yamamoto <hitoshiy@isl.melco.co.jp>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch removes an obsolete header file include/asm-m32r/m32102peri.h.
In this header, there are some undesirable single character types, like V.
And the header is almost no longer used.
Signed-off-by: Hayato Fujiwara <fujiwara@linux-m32r.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patchset is for supporting a new m32r platform, M3A-2170(Mappi-III)
evaluation board. An M32R chip multiprocessor is equipped on the board.
http://http://www.linux-m32r.org/eng/platform/platform.html
* arch/m32r/Kconfig: Support Mappi-III platform.
* arch/m32r/kernel/Makefile: ditto.
* arch/m32r/kernel/io_mappi3.c: ditto.
* arch/m32r/kernel/setup.c: ditto.
* arch/m32r/kernel/setup_mappi3.c: ditto.
* include/asm-m32r/m32102.h: ditto.
* include/asm-m32r/m32r.h: ditto.
* include/asm-m32r/mappi3/mappi3_pld.h: ditto.
* include/asm-m32r/ide.h: CF support for Mappi-III.
* arch/m32r/kernel/setup_mappi3.c: ditto.
* arch/m32r/mappi3/defconfig.smp: A default config file for Mappi-III.
* arch/m32r/mappi3/dot.gdbinit: A default .gdbinit file for Mappi-III.
* arch/m32r/boot/compressed/m32r_sio.c: Modified for Mappi-III
- At boot time, m32r-g00ff bootloader makes MMU off for Mappi-III,
on the contrary it makes MMU on for Mappi-II.
* arch/m32r/kernel/io_mappi2.c: Update comments.
* arch/m32r/kernel/setup_mappi2.c: ditto.
Signed-off-by: Mamoru Sakugawa <sakugawa@linux-m32r.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Several hardware features of SGI's IOC4 I/O controller chip require
timing-related driver calculations dependent upon the PCI bus speed. This
patch enables the core IOC4 driver code to detect the actual bus speed and
store a value that can later be used by the IOC4 subdrivers as needed.
Signed-off-by: Brent Casavant <bcasavan@sgi.com>
Acked-by: Pat Gefre <pfg@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This series of patches reworks the configuration and internal structure
of the SGI IOC4 I/O controller device drivers.
These changes are motivated by several factors:
- The IOC4 chip PCI resources are of mixed use between functions (i.e.
multiple functions are handled in the same address range, sometimes
within the same register), muddling resource ownership and initialization
issues. Centralizing this ownership in a core driver is desirable.
- The IOC4 chip implements multiple functions (serial, IDE, others not
yet implemented in the mainline kernel) but is not a multifunction
PCI device. In order to properly handle device addition and removal
as well as module insertion and deletion, an intermediary IOC4-specific
driver layer is needed to handle these operations cleanly.
- All IOC4 drivers are currently enabled by a single CONFIG value. As
not all systems need all IOC4 functions, it is desireable to enable
these drivers independently.
- The current IOC4 core driver will trigger loading of all function-level
drivers, as it makes direct calls to them. This situation should be
reversed (i.e. function-level drivers cause loading of core driver)
in order to maintain a clear and least-surprise driver loading model.
- IOC4 hardware design necessitates some driver-level dependency on
the PCI bus clock speed. Current code assumes a 66MHz bus, but the
speed should be autodetected and appropriate compensation taken.
This patch series effects the above changes by a newly and better designed
IOC4 core driver with which the function-level drivers can register and
deregister themselves upon module insertion/removal. By tracking these
modules, device addition/removal is also handled properly. PCI resource
management and ownership issues are centralized in this core driver, and
IOC4-wide configuration actions such as bus speed detection are also
handled in this core driver.
This patch:
The SGI IOC4 I/O controller chip implements multiple functions, though it is
not a multi-function PCI device. Additionally, various PCI resources of the
IOC4 are shared by multiple hardware functions, and thus resource ownership by
driver is not clearly delineated. Due to the current driver design, all core
and subordinate drivers must be loaded, or none, which is undesirable if not
all IOC4 hardware features are being used.
This patch reorganizes the IOC4 drivers so that the core driver provides a
subdriver registration service. Through appropriate callbacks the subdrivers
can now handle device addition and removal, as well as module insertion and
deletion (though the IOC4 IDE driver requires further work before module
deletion will work). The core driver now takes care of allocating PCI
resources and data which must be shared between subdrivers, to clearly
delineate module ownership of these items.
Signed-off-by: Brent Casavant <bcasavan@sgi.com>
Acked-by: Pat Gefre <pfg@sgi.com
Acked-by: Jeremy Higdon <jeremy@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Add vr41xx gpio support.
Signed-off-by: Yoichi Yuasa <yuasa@hh.iij4u.or.jp>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch allows iSeries to build with CONFIG_PCI=n. This is useful for
partitions that have only virtual I/O.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch just removes some dead code, fixes messages that referred to the
file this code used to be in and inserts XmPciLpEvent_init into its caller.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch is just simple cleanups to the iSeries irq code.
- whitespace and comments
- rearrange some functions to avoid forward declarations
- remove XmPciLpEvent.h as its functions were declared elsewhere
- remove decaration of function that no longer exists
No semantic changes.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The AgentId, PhbId, FrameId, CardLocation and Location members of
iSeries_Device_Node are stored early in the boot process just so that a
message about the device can be printed later in the boot process. Remove
them and construct the message by doing the VPD parsing at the time the
message is printed.
Also remove a few unused defines in iSeries_VpdInfo.c.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The IoRetry member of iSeries_Devide_Node is really only used locally, so
remove it and replace it with a local variable.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Remove no longer used things from iSeries_pci.h.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The iommu_table_cb structure is iSeries specific, so move it to the header
file that declares the function we pass it to. vio_tce_table and
iommu_setup_iSeries no longer exist, so remove their declarations.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The file arch/ppc64/kernel/iSeries_pci_reset contains only one function that
is not use anywhere (any more). Remove it. This function is the only user of
the ReturnCode member of iSeries_Device_Node, so remove that as well.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Last of this round of the iSeries header cleanups
- don't have two defines for the same thing (HvMaxArchitectedLps
and HvMaxArchitectedVirtualLans)
- HvCallSc.h only needs linux/types.h
- remove unused struct definition
- add "extern" to some more function declarations
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch removes some unused bits from HvCall.h and some unneeded #includes
from other files. Also includes ItLpQueue.h in paca.h in preference to a stub
declaration of struct ItLpQueue.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
Shaun Pereira
Jeff Moyer
Harald Welte
Linus Torvalds
Takashi Iwai
Jaroslav Kysela
Jaroslav Kysela
Randy Vinson
Jean Delvare
David Brownell
Sebastian Witt
NeilBrown
James Simmons
Jurriaan
James Simmons
Jaya Kumar
Ian Kent
Paolo 'Blaisorblade' Giarrusso
Hirokazu Takata
Brent Casavant
Yoichi Yuasa
Stephen Rothwell