| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
switch to using the new timer_setup() and from_timer() api's.
Signed-off-by: Allen Pais <allen.pais@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure the device and the kernel are performing the multipath hash
according to the same parameters by updating the device whenever the
relevant netevent is generated.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Up until now we used the hardware's defaults for multipath hash
computation. This patch aligns the hardware's multipath parameters with
the kernel's.
For IPv4 packets, the parameters are determined according to the
'fib_multipath_hash_policy' sysctl during module initialization. In case
L3-mode is requested, only the source and destination IP addresses are
used. There is no special handling of ICMP error packets.
In case L4-mode is requested, a 5-tuple is used: source and destination
IP addresses, source and destination ports and IP protocol. Note that
the layer 4 fields are not considered for fragmented packets.
For IPv6 packets, the source and destination IP addresses are used, as
well as the flow label and the next header fields.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The RECRv2 register is used for setting up the router's ECMP hash
configuration.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The struct containing the work item queued from the netevent handler is
named after the only event it is currently used for, which is neighbour
updates.
Use a more appropriate name for the struct, as we are going to use it
for more events.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We are going to need to respond to netevents notifying us about
multipath hash updates by configuring the device's hash parameters.
Embed the netevent notifier in the router struct so that we could
retrieve it upon notifications and use it to configure the device.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Devices performing IPv4 forwarding need to update their multipath hash
policy whenever it is changed.
Inform these devices by generating a netevent.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix to return a negative error code from thecxgb4_alloc_atid()
error handling case instead of 0.
Fixes: 12b276fbf6e0 ("cxgb4: add support to create hash filters")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-By: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The bpf_verifer_ops array is generated dynamically and may be
empty depending on configuration, which then causes an out
of bounds access:
kernel/bpf/verifier.c: In function 'bpf_check':
kernel/bpf/verifier.c:4320:29: error: array subscript is above array bounds [-Werror=array-bounds]
This adds a check to the start of the function as a workaround.
I would assume that the function is never called in that configuration,
so the warning is probably harmless.
Fixes: 00176a34d9e2 ("bpf: remove the verifier ops from program structure")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I ran into this link error with the latest net-next plus linux-next
trees when networking is disabled:
kernel/bpf/verifier.o:(.rodata+0x2958): undefined reference to `tc_cls_act_analyzer_ops'
kernel/bpf/verifier.o:(.rodata+0x2970): undefined reference to `xdp_analyzer_ops'
It seems that the code was written to deal with varying contents of
the arrray, but the actual #ifdef was missing. Both tc_cls_act_analyzer_ops
and xdp_analyzer_ops are defined in the core networking code, so adding
a check for CONFIG_NET seems appropriate here, and I've verified this with
many randconfig builds
Fixes: 4f9218aaf8a4 ("bpf: move knowledge about post-translation offsets out of verifier")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The lan9303 driver defines eth_stp_addr as a synonym to
eth_reserved_addr_base to get the STP ethernet address 01:80:c2:00:00:00.
eth_reserved_addr_base is also used to define the start of Bridge Reserved
ethernet address range, which happen to be the STP address.
br_dev_setup refer to eth_reserved_addr_base as a definition of STP
address.
Clean up by:
- Move the eth_stp_addr definition to linux/etherdevice.h
- Use eth_stp_addr instead of eth_reserved_addr_base in br_dev_setup.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Acked-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This tracepoint can be used to trace synack retransmits. It maintains
pointer to struct request_sock.
We cannot simply reuse trace_tcp_retransmit_skb() here, because the
sk here is the LISTEN socket. The IP addresses and ports should be
extracted from struct request_sock.
Note that, like many other tracepoints, this patch uses IS_ENABLED
in TP_fast_assign macro, which triggers sparse warning like:
./include/trace/events/tcp.h:274:1: error: directive in argument list
./include/trace/events/tcp.h:281:1: error: directive in argument list
However, there is no good solution to avoid these warnings. To the
best of our knowledge, these warnings are harmless.
Signed-off-by: Song Liu <songliubraving@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RFC 8200 (IPv6) defines Hop-by-Hop options and Destination options
extension headers. Both of these carry a list of TLVs which is
only limited by the maximum length of the extension header (2048
bytes). By the spec a host must process all the TLVs in these
options, however these could be used as a fairly obvious
denial of service attack. I think this could in fact be
a significant DOS vector on the Internet, one mitigating
factor might be that many FWs drop all packets with EH (and
obviously this is only IPv6) so an Internet wide attack might not
be so effective (yet!).
By my calculation, the worse case packet with TLVs in a standard
1500 byte MTU packet that would be processed by the stack contains
1282 invidual TLVs (including pad TLVS) or 724 two byte TLVs. I
wrote a quick test program that floods a whole bunch of these
packets to a host and sure enough there is substantial time spent
in ip6_parse_tlv. These packets contain nothing but unknown TLVS
(that are ignored), TLV padding, and bogus UDP header with zero
payload length.
25.38% [kernel] [k] __fib6_clean_all
21.63% [kernel] [k] ip6_parse_tlv
4.21% [kernel] [k] __local_bh_enable_ip
2.18% [kernel] [k] ip6_pol_route.isra.39
1.98% [kernel] [k] fib6_walk_continue
1.88% [kernel] [k] _raw_write_lock_bh
1.65% [kernel] [k] dst_release
This patch adds configurable limits to Destination and Hop-by-Hop
options. There are three limits that may be set:
- Limit the number of options in a Hop-by-Hop or Destination options
extension header.
- Limit the byte length of a Hop-by-Hop or Destination options
extension header.
- Disallow unrecognized options in a Hop-by-Hop or Destination
options extension header.
The limits are set in corresponding sysctls:
ipv6.sysctl.max_dst_opts_cnt
ipv6.sysctl.max_hbh_opts_cnt
ipv6.sysctl.max_dst_opts_len
ipv6.sysctl.max_hbh_opts_len
If a max_*_opts_cnt is less than zero then unknown TLVs are disallowed.
The number of known TLVs that are allowed is the absolute value of
this number.
If a limit is exceeded when processing an extension header the packet is
dropped.
Default values are set to 8 for options counts, and set to INT_MAX
for maximum length. Note the choice to limit options to 8 is an
arbitrary guess (roughly based on the fact that the stack supports
three HBH options and just one destination option).
These limits have being proposed in draft-ietf-6man-rfc6434-bis.
Tested (by Martin Lau)
I tested out 1 thread (i.e. one raw_udp process).
I changed the net.ipv6.max_dst_(opts|hbh)_number between 8 to 2048.
With sysctls setting to 2048, the softirq% is packed to 100%.
With 8, the softirq% is almost unnoticable from mpstat.
v2;
- Code and documention cleanup.
- Change references of RFC2460 to be RFC8200.
- Add reference to RFC6434-bis where the limits will be in standard.
Signed-off-by: Tom Herbert <tom@quantonium.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All member of Struct hdev->hw_stats is initialized to 0 as hdev is
allocated by devm_kzalloc. But in reset process, hdev will not be
allocated again, so need clear hdev->hw_stats in reset process, otherwise
the statistic will be wrong after reset. This patch set all of the
statistic counters to zero after reset.
Signed-off-by: qumingguang <qumingguang@huawei.com>
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
we should use free_irq to free the nic irq during the unloading time.
because we use request_irq to apply it when nic up. It will crash if
up net device after reset the port. This patch fixes the issue.
Signed-off-by: qumingguang <qumingguang@huawei.com>
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch implement the interface of reset notification in hns3_enet,
it will do resetting business which include shutdown nic device,
free and initialize client side resource.
Signed-off-by: qumingguang <qumingguang@huawei.com>
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch add timeout handler in hns3_enet.c to handle
TX side timeout event, when TX timeout event occur, it will triger
NIC driver into reset process.
Signed-off-by: qumingguang <qumingguang@huawei.com>
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds reset support for PF,it include : global reset, core reset,
IMP reset, PF reset.The core reset will Reset all datapath of all functions
except IMP, MAC and PCI interface. Global reset is equal with the core
reset plus all MAC reset. IMP reset is caused by watchdog timer expiration,
the same with core reset in the reset flow. PF reset will reset whole
physical function.
Signed-off-by: qumingguang <qumingguang@huawei.com>
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds initialization and deinitialization for misc interrupt.
This interrupt will be used to handle reset message(IRQ).
Signed-off-by: qumingguang <qumingguang@huawei.com>
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no necessary to reallocate the descriptor and remap the descriptor
memory in reset process, But there is still some other action exist in both
reset process and initialization process.
To reuse the common interface in reset process and initialization process,
This patch moves out the descriptor allocate and memory maping from
interface cmdq_init.
Signed-off-by: qumingguang <qumingguang@huawei.com>
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It needs initialize mdio in initialization process, but reset process
does not reset mdio, so do not initialize mdio in reset process.
This patch move out the mdio configuration function from the mac_init.
So mac_init can be used both in reset process and initialization process.
Signed-off-by: qumingguang <qumingguang@huawei.com>
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch refactor the mapping of tqp to vport, making the maping function
can be used both in the reset process and initialization process.
Signed-off-by: qumingguang <qumingguang@huawei.com>
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
One of the timer conversion patches evidently escaped build testing
until I ran into in on ARM randconfig builds:
drivers/net/ethernet/seeq/ether3.c: In function 'ether3_ledoff':
drivers/net/ethernet/seeq/ether3.c:175:40: error: 'priv' undeclared (first use in this function); did you mean 'pid'?
drivers/net/ethernet/seeq/ether3.c:176:27: error: initialization from incompatible pointer type [-Werror=incompatible-pointer-types]
This fixes the two small typos that caused the problems.
Fixes: 6fd9c53f7186 ("net: seeq: Convert timers to use timer_setup()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Allen Pais
Ido Schimmel
Wei Yongjun
Arnd Bergmann
Egil Hjelmeland
Felix Manlunas
Song Liu
Tom Herbert
qumingguang
Lipeng