| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
If there are a lot of outstanding buffered IOs when a device is
taken offline (due to hardware errors etc), ext4_end_bio prints
out a message for each failed logical block. While this is desirable,
we see thousands of such lines being printed out before the
serial console gets overwhelmed, causing ext4_end_bio() wait for
the printk to complete.
This in itself isn't a disaster, except for the detail that this
function is being called with the queue lock held.
This causes any other function in the block layer
to spin on its spin_lock_irqsave while the serial console is
draining. If NMI watchdog is enabled on this machine then it
eventually comes along and shoots the machine in the head.
The end result is that losing any one disk causes the machine to
go down. This patch rate limits the printk to bandaid around the
problem.
Tested: xfstests
Change-Id: I8ab5690dcf4f3a67e78be147d45e489fdf4a88d8
Signed-off-by: Anatol Pomozov <anatol.pomozov@gmail.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
|
|
Since commit ab78029 (drivers/pinctrl: grab default handles from device core),
we can rely on device core for setting the default pins. Compile tested only.
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit ab78029 (drivers/pinctrl: grab default handles from device core),
we can rely on device core for setting the default pins. Compile tested only.
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit ab78029 (drivers/pinctrl: grab default handles from device core),
we can rely on device core for setting the default pins. Compile tested only.
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Base on cdc_ether, add the mii functions for RTL8152 and RTL8153.
The RTL8152 and RTL8153 support ECM mode which use the driver of
cdc_ether. Add the mii functions. Then, the basic PHY access is
possible.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of passing each byte by stack let's use nice specifier for that.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For copy_to/from_user() failure, the correct error code is -EFAULT not
-EPERM.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
This patch adds code to log SDMA errors for supportability purposes.
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
The vzalloc()'ed field physshadow is leaked on module unload.
This patch adds vfree after the sibling page shadow is freed.
Reported-by: Dean Luick <dean.luick@intel.com>
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Sparse reported an endianness bug in the assignment to hca_cap.uar_page_sz.
Fix the declaration of this field to be __be16 (which is what is in
the firmware spec), renaming the field to log_uar_pg_size to conform
to the spec, which fixes the endianness bug reported by sparse.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Moshe Lazer <moshel@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
If the transport layer is offline it is more appropriate to let
srp_abort() return FAST_IO_FAIL instead of SUCCESS.
Reported-by: Sebastian Riemer <sebastian.riemer@profitbricks.com>
Acked-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change fixes an MTU sizing issue seen with gretap tunnels when non-gso
packets are sent from the interface.
In my case I was able to reproduce the issue by simply sending a ping of
1421 bytes with the gretap interface created on a device with a standard
1500 mtu.
This fix is based on the fact that the tunnel mtu is already adjusted by
dev->hard_header_len so it would make sense that any packets being compared
against that mtu should also be adjusted by hard_header_len and the tunnel
header instead of just the tunnel header.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Reported-by: Cong Wang <amwang@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we request reading or writing on a file that needs to be
reopened, it causes the deadlock: we are already holding rw
semaphore for reading and then we try to acquire it for writing
in cifs_relock_file. Fix this by acquiring the semaphore for
reading in cifs_relock_file due to we don't make any changes in
locks and don't need a write access.
CC: <stable@vger.kernel.org>
Signed-off-by: Pavel Shilovsky <pshilovsky@samba.org>
Acked-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
|
|
This is a follow-on patch for 8/8 patch from the durable handles
series. It fixes the problem when durable file handle timeout
expired on the server and reopen returns -ENOENT for such files.
Signed-off-by: Pavel Shilovsky <pshilovsky@samba.org>
Signed-off-by: Steve French <smfrench@gmail.com>
|
|
We now print mount options in a generic fashion in
ext4_show_options(), so we shouldn't be explicitly printing the
{usr,grp}quota options in ext4_show_quota_options().
Without this patch, /proc/mounts can look like this:
/dev/vdb /vdb ext4 rw,relatime,quota,usrquota,data=ordered,usrquota 0 0
^^^^^^^^ ^^^^^^^^
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@vger.kernel.org
|
|
During the review of seperate pquota inode patches, David noticed
that the test to detect all quotas being turned off was
incorrect, and hence the block was not freeing all the quota
information.
The check made sense in Irix, but in Linux, quota is turned off
one at a time, which makes the test invalid for Linux.
This problem existed since XFS was ported to Linux.
David suggested to fix the problem by detecting when all quotas are
turned off by checking m_qflags.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Reviewed-by: Ben Myers <bpm@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
|
|
This patch is being created to use the UEFI bits in the type 219 SMBIOS
record in order to decide whether or not to execute BIOS code. This is a
better solution than to depend on the iCRU bit since not all future servers
will use iCRU.
Signed-off-by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
----
drivers/watchdog/hpwdt.c | 9 ++++++---
1 files changed, 6 insertions(+), 3 deletions(-)
|
|
In watchdog_ping(), 'start' is called automatically when 'ping' function call
is not configured.
Softdog driver has same handling in both cases - start and ping, so 'ping' OPS
can be removed.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
This patch adds the driver for the watchdog devices found on MEN Mikro
Elektronik A21 VMEbus CPU Carrier Boards. It has DT-support and uses the
watchdog framework.
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@men.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
The bits in BRIDGE_CAUSE are documented as RW0C - read, write 0 to
clear. If we read the register, mask off the watchdog bit, and
write it back, we're actually clearing every interrupt which wasn't
pending at the time we read the register - and that is racy.
Fix this to only write ~WATCHDOG_BIT to the register, which means
we write as zero only the watchdog bit.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
The watchdog infrastructure in Dove is no different from that in
Orion5x or Kirkwood, so let's enable it for Dove. The only things
missing are a few register settings in Dove's bridge-regs.h.
Rather than duplicating the same register bit masks for the RSTOUTn_MASK
and BRIDGE_CAUSE registers, move the definitions into the watchdog
driver itself.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
This adds a driver for watchdog timer hardware present on Broadcom BCM2835 SoC,
used in Raspberry Pi and Roku 2 devices.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-rpi-kernel@lists.infradead.org
Cc: linux-watchdog@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
|
|
This patch removes the forward declaration of qfq_update_agg_ts, by moving
the definition of the function above its first call. This patch also
removes a useless forward declaration of qfq_schedule_agg.
Reported-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paolo Valente <paolo.valente@unimore.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In make_eligible, a mask is used to decide which groups must become eligible:
the i-th group becomes eligible only if the i-th bit of the mask (from the
right) is set. The mask is computed by left-shifting a 1 by a given number of
places, and decrementing the result. The shift is performed on a ULL to avoid
problems in case the number of places to shift is higher than 31. On a 32-bit
machine, this is more costly than working on an UL. This patch replaces such a
costly operation with two cheaper branches.
The trick is based on the following fact: in case of a shift of at least 32
places, the resulting mask has at least the 32 less significant bits set,
whereas the total number of groups is lower than 32. As a consequence, in this
case it is enough to just set the 32 less significant bits of the mask with a
cheaper ~0UL. In the other case, the shift can be safely performed on a UL.
Reported-by: David S. Miller <davem@davemloft.net>
Reported-by: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Paolo Valente <paolo.valente@unimore.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Interrupt request doesn't use the right API: The TWD watchdog uses a per-cpu
interrupt (usually interrupt #30), and the GIC configuration should flag it as
such. With this setup, request_irq() should fail, and the right API is
request_percpu_irq(), together with enable_percpu_irq()/disable_percpu_irq().
Nothing ensures the userspace ioctl() will end-up kicking the watchdog on the
right CPU.
There are no users of this driver since a long time and it makes more sense to
get rid of it as nobody is looking to fix it.
In case somebody wakes up after this has been removed and needs it, please
revert this driver and pick these updates (These were never pushed to mainline):
http://comments.gmane.org/gmane.linux.ports.arm.kernel/245998
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Watchdog 1.01.a is also compatible with 1.00.a.
Add the origin version to compatible list.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
- Remove reference for IP version
- Fix header coding style
- Remove notes which are visible from the code
- Fix driver license according to header
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Kernel has nice helpers to dump buffers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
This change makes it so that the GRE and VXLAN tunnels can make use of Tx
checksum offload support provided by some drivers via the hw_enc_features.
Without this fix enabling GSO means sacrificing Tx checksum offload and
this actually leads to a performance regression as shown below:
Utilization
Send
Throughput local GSO
10^6bits/s % S state
6276.51 8.39 enabled
7123.52 8.42 disabled
To resolve this it was necessary to address two items. First
netif_skb_features needed to be updated so that it would correctly handle
the Trans Ether Bridging protocol without impacting the need to check for
Q-in-Q tagging. To do this it was necessary to update harmonize_features
so that it used skb_network_protocol instead of just using the outer
protocol.
Second it was necessary to update the GRE and UDP tunnel segmentation
offloads so that they would reset the encapsulation bit and inner header
offsets after the offload was complete.
As a result of this change I have seen the following results on a interface
with Tx checksum enabled for encapsulated frames:
Utilization
Send
Throughput local GSO
10^6bits/s % S state
7123.52 8.42 disabled
8321.75 5.43 enabled
v2: Instead of replacing refrence to skb->protocol with
skb_network_protocol just replace the protocol reference in
harmonize_features to allow for double VLAN tag checks.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A watchdog device may be stopped from userspace using WDIOC_SETOPTIONS
ioctl and flag WDIOS_DISABLECARD. If the device is closed after this
operation, watchdog_release() is called and status bits checked for
stopping it. Besides, if the device has not been unregistered a critical
message "watchdog did not stop!" is printed, although the ioctl may have
successfully stopped it already.
Without the patch a user application sample code like this will successfully
stop the watchdog, but the kernel will output the message
"watchdog did not stop!":
wd_fd = open("/dev/watchdog", O_RDWR);
flags = WDIOS_DISABLECARD;
ioctl(wd_fd, WDIOC_SETOPTIONS, &flags);
close(wd_fd);
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
In preparation to switching the jz4740 clk driver to the common clk framework
make sure to pass the device to clk_get().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Timo Kokkonen <timo.t.kokkonen@nokia.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Instead of using legacy suspend/resume methods, using newer
dev_pm_ops structure allows better control over power management.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
dev_err()/dev_info() are more preferred than pr_err()/pr_info().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Use devm_gpio_request_one() to make cleanup paths simpler.
Also, GPIOF_DIR_OUT | GPIOF_INIT_LOW is replaced with
GPIOF_OUT_INIT_LOW.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Use devm_gpio_request_one() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Use devm_clk_get() to make cleanup paths more simple.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Found using checkpatch.pl
Signed-off-by: Camelia Groza <camelia.groza@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use devm_clk_get() to make cleanup paths more simple.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Use devm_clk_get() to make cleanup paths more simple.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Use devm_clk_get() to make cleanup paths more simple.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
'dw_wdt_write' is used only in this file. Make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
If __rtnl_link_register() return faild when loading the ifb, it will
take the wrong path and get oops, so fix it just like dummy.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Anatol Pomozov
Wolfram Sang
hayeswang
Andy Shevchenko
Dan Carpenter
Dean Luick
Mike Marciniszyn
Moshe Lazer
Bart Van Assche
Jitendra Kalsaria
Alexander Duyck
Pavel Shilovsky
Theodore Ts'o
Chandra Seetharaman
Mingarelli, Thomas
Kim, Milo
Johannes Thumshirn
Russell King
Lubomir Rintel
Paolo Valente
Viresh Kumar
Michal Simek
Hector Palacios
Lars-Peter Clausen
Sachin Kamat
Jingoo Han
Camelia Groza
dingtianhong