| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
At present, "systemctl suspend" and "shutdown" can run in parrallel. A
system can suspend after devices_shutdown(), and resume. Then the shutdown
task goes on to power off. This causes many devices are not really shut
off. Hence replacing reboot_mutex with system_transition_mutex (renamed
from pm_mutex) to achieve the exclusion. The renaming of pm_mutex as
system_transition_mutex can be better to reflect the purpose of the mutex.
Signed-off-by: Pingfan Liu <kernelfans@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
As files move around, their previous links break. Fix the
references for them.
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
|
|
Since pm_mutex is not exported using lock/unlock_system_sleep() from
inside a kernel module causes a "pm_mutex undefined" linker error.
Hence move lock/unlock_system_sleep() into kernel/power/main.c and
export these.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
For SoC to achieve its lowest power platform idle state a set of hardware
preconditions must be met. These preconditions or constraints can be
obtained by issuing a device specific method (_DSM) with function "1".
Refer to the document provided in the link below.
Here during initialization (from attach() callback of LPS0 device), invoke
function 1 to get the device constraints. Each enabled constraint is
stored in a table.
The devices in this table are used to check whether they were in required
minimum state, while entering suspend. This check is done from platform
freeze wake() callback, only when /sys/power/pm_debug_messages attribute
is non zero.
If any constraint is not met and device is ACPI power managed then it
prints the device information to kernel logs.
Also if debug is enabled in acpi/sleep.c, the constraint table and state
of each device on wake is dumped in kernel logs.
Since pm_debug_messages_on setting is used as condition to check
constraints outside kernel/power/main.c, pm_debug_messages_on is changed
to a global variable.
Link: http://www.uefi.org/sites/default/files/resources/Intel_ACPI_Low_Power_S0_Idle.pdf
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The pm_test sysfs attribute is under CONFIG_PM_DEBUG, but it doesn't
make sense to provide it if CONFIG_PM_SLEEP is unset, so put it under
CONFIG_PM_SLEEP_DEBUG instead.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The messages printed by tk_debug_account_sleep_time() are basically
useful for system sleep debugging, so print them only when the other
debug messages from the core suspend/hibernate code are enabled.
While at it, make it clear that the messages from
tk_debug_account_sleep_time() are about timekeeping suspend
duration, because in general timekeeping may be suspeded and
resumed for multiple times during one system suspend-resume cycle.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Debug messages from the system suspend/hibernation infrastructure can
fill up the entire kernel log buffer in some cases and anyway they
are only useful for debugging. They depend on CONFIG_PM_DEBUG, but
that is set as a rule as some generally useful diagnostic facilities
depend on it too.
For this reason, avoid printing those messages by default, but make
it possible to turn them on as needed with the help of a new sysfs
attribute under /sys/power/.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
3802 624 32 4458 116a kernel/power/main.o
File size After adding 'const':
text data bss dec hex filename
3866 560 32 4458 116a kernel/power/main.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
There are systems in which the platform doesn't support any special
sleep states, so suspend-to-idle (PM_SUSPEND_FREEZE) is the only
available system sleep state. However, some user space frameworks
only use the "mem" and (sometimes) "standby" sleep state labels, so
the users of those systems need to modify user space in order to be
able to use system suspend at all and that may be a pain in practice.
Commit 0399d4db3edf (PM / sleep: Introduce command line argument for
sleep state enumeration) attempted to address this problem by adding
a command line argument to change the meaning of the "mem" string in
/sys/power/state to make it trigger suspend-to-idle (instead of
suspend-to-RAM).
However, there also are systems in which the platform does support
special sleep states, but suspend-to-idle is the preferred one anyway
(it even may save more energy than the platform-provided sleep states
in some cases) and the above commit doesn't help in those cases.
For this reason, rework the system sleep state selection interface
again (but preserve backwards compatibiliby). Namely, add a new
sysfs file, /sys/power/mem_sleep, that will control the system
suspend mode triggered by writing "mem" to /sys/power/state (in
analogy with what /sys/power/disk does for hibernation). Make it
select suspend-to-RAM ("deep" sleep) by default (if supported) and
fall back to suspend-to-idle ("s2idle") otherwise and add a new
command line argument, mem_sleep_default, allowing that default to
be overridden if need be.
At the same time, drop the relative_sleep_states command line
argument that doesn't make sense any more.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mario Limonciello <mario.limonciello@dell.com>
|
|
Suspend-to-idle (aka the "freeze" sleep state) is a system sleep state
in which all of the processors enter deepest possible idle state and
wait for interrupts right after suspending all the devices.
There is no hard requirement for a platform to support and register
platform specific suspend_ops to enter suspend-to-idle/freeze state.
Only deeper system sleep states like PM_SUSPEND_STANDBY and
PM_SUSPEND_MEM rely on such low level support/implementation.
suspend-to-idle can be entered as along as all the devices can be
suspended. This patch enables the support for suspend-to-idle even on
systems that don't have any low level support for deeper system sleep
states and/or don't register any platform specific suspend_ops.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This makes pm notifier PREPARE/POST symmetrical: if PREPARE
fails, we will only undo what ever happened on PREPARE.
It fixes the unbalanced CPU hotplug enable in CPU PM notifier.
Signed-off-by: Lianwei Wang <lianwei.wang@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Some sysfs attributes in /sys/power/ should really be read-only,
so add support for that, convert those attributes to read-only
and drop the stub .show() routines from them.
Original-by: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Add a sysfs attribute, /sys/power/pm_wakeup_irq, reporting the IRQ
number of the first wakeup interrupt (that is, the first interrupt
from an IRQ line armed for system wakeup) seen by the kernel during
the most recent system suspend/resume cycle.
This feature will be useful for system wakeup diagnostics of
spurious wakeup interrupts.
Signed-off-by: Alexandra Yates <alexandra.yates@linux.intel.com>
[ rjw: Fixed up pm_wakeup_irq definition ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Occasionally, the system can't come back up after suspend/resume
due to problems of device suspending phase. This patch make
PM_TRACE infrastructure cover device suspending phase of
suspend/resume process, and the information in RTC can tell
developers which device suspending function make system hang.
Signed-off-by: Zhonghui Fu <zhonghui.fu@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
* pm-apm:
x86, apm: Remove unused variable
* pm-sleep:
PM / sleep: Move platform suspend operations to separate functions
PM / sleep: Simplify sleep states sysfs interface code
|
|
The PM workqueue is going to be used by ACPI PM notify handlers
regardless of whether or not runtime PM is configured, so move
it out of #ifdef CONFIG_PM_RUNTIME.
Do that in three places in the ACPI device PM code.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Simplify the sleep states sysfs interface /sys/power/state code by
redefining pm_states[] as an array of pointers to constant strings
such that only the entries corresponding to valid states are set.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
To support using kernel features that are not compatible with hibernation,
this creates the "nohibernate" kernel boot parameter to disable both
hibernation and resume. This allows hibernation support to be a boot-time
choice instead of only a compile-time choice.
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
On some systems the platform doesn't support neither
PM_SUSPEND_MEM nor PM_SUSPEND_STANDBY, so PM_SUSPEND_FREEZE is the
only available system sleep state. However, some user space frameworks
only use the "mem" and (sometimes) "standby" sleep state labels, so
the users of those systems need to modify user space in order to be
able to use system suspend at all and that is not always possible.
For this reason, add a new kernel command line argument,
relative_sleep_states, allowing the users of those systems to change
the way in which the kernel assigns labels to system sleep states.
Namely, for relative_sleep_states=1, the "mem", "standby" and "freeze"
labels will enumerate the available system sleem states from the
deepest to the shallowest, respectively, so that "mem" is always
present in /sys/power/state and the other state strings may or may
not be presend depending on what is supported by the platform.
Update system sleep states documentation to reflect this change.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Use the observation that, for platform-dependent sleep states
(PM_SUSPEND_STANDBY, PM_SUSPEND_MEM), a given state is either
always supported or always unsupported and store that information
in pm_states[] instead of calling valid_state() every time we
need to check it.
Also do not use valid_state() for PM_SUSPEND_FREEZE, which is always
valid, and move the pm_test_level validity check for PM_SUSPEND_FREEZE
directly into enter_state().
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
To allow sleep states corresponding to the "mem", "standby" and
"freeze" lables to be different from the pm_states[] indexes of
those strings, introduce struct pm_sleep_state, consisting of
a string label and a state number, and turn pm_states[] into an
array of objects of that type.
This modification should not lead to any functional changes.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Fix descriptions of /sys/power/state in the documentation and in
a code comment.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
[rjw: Changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
pm_trace uses the system's Real Time Clock (RTC) to save the magic
number. The reason for this is that the RTC is the only reliably
available piece of hardware during resume operations where a value
can be set that will survive a reboot.
Consequence is that after a resume (even if it is successful) your
system clock will have a value corresponding to the magic number
instead of the correct date/time! It is therefore advisable to use
a program like ntp-date or rdate to reset the correct date/time from
an external time source when using this trace option.
There is no run-time message to warn users of the consequences of
enabling pm_trace. Adding a warning message to pm_trace_store()
will serve as a reminder to users to set the system date and time
after resume.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Commit a938da06 introduced a useful little log message to tell
users/debuggers which wakeup source aborted a suspend. However,
this message is only printed if the abort happens during the
in-kernel suspend path (after writing /sys/power/state).
The full specification of the /sys/power/wakeup_count facility
allows user-space power managers to double-check if wakeups have
already happened before it actually tries to suspend (e.g. while it
was running user-space pre-suspend hooks), by writing the last known
wakeup_count value to /sys/power/wakeup_count. This patch changes
the sysfs handler for that node to also print said log message if
that write fails, so that we can figure out the offending wakeup
source for both kinds of suspend aborts.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
At present, the value of timeout for freezing is 20s, which is
meaningless in case that one thread is frozen with mutex locked
and another thread is trying to lock the mutex, as this time of
freezing will fail unavoidably.
And if there is no new wakeup event registered, the system will
waste at most 20s for such meaningless trying of freezing.
With this patch, the value of timeout can be configured to smaller
value, so such meaningless trying of freezing will be aborted in
earlier time, and later freezing can be also triggered in earlier
time. And more power will be saved.
In normal case on mobile phone, it costs real little time to freeze
processes. On some platform, it only costs about 20ms to freeze
user space processes and 10ms to freeze kernel freezable threads.
Signed-off-by: Liu Chuansheng <chuansheng.liu@intel.com>
Signed-off-by: Li Fei <fei.li@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
PM_SUSPEND_FREEZE state is a general state that
does not need any platform specific support, it equals
frozen processes + suspended devices + idle processors.
Compared with PM_SUSPEND_MEMORY,
PM_SUSPEND_FREEZE saves less power
because the system is still in a running state.
PM_SUSPEND_FREEZE has less resume latency because it does not
touch BIOS, and the processors are in idle state.
Compared with RTPM/idle,
PM_SUSPEND_FREEZE saves more power as
1. the processor has longer sleep time because processes are frozen.
The deeper c-state the processor supports, more power saving we can get.
2. PM_SUSPEND_FREEZE uses system suspend code path, thus we can get
more power saving from the devices that does not have good RTPM support.
This state is useful for
1) platforms that do not have STR, or have a broken STR.
2) platforms that have an extremely low power idle state,
which can be used to replace STR.
The following describes how PM_SUSPEND_FREEZE state works.
1. echo freeze > /sys/power/state
2. the processes are frozen.
3. all the devices are suspended.
4. all the processors are blocked by a wait queue
5. all the processors idles and enters (Deep) c-state.
6. an interrupt fires.
7. a processor is woken up and handles the irq.
8. if it is a general event,
a) the irq handler runs and quites.
b) goto step 4.
9. if it is a real wake event, say, power button pressing, keyboard touch, mouse moving,
a) the irq handler runs and activate the wakeup source
b) wakeup_source_activate() notifies the wait queue.
c) system starts resuming from PM_SUSPEND_FREEZE
10. all the devices are resumed.
11. all the processes are unfrozen.
12. system is back to working.
Known Issue:
The wakeup of this new PM_SUSPEND_FREEZE state may behave differently
from the previous suspend state.
Take ACPI platform for example, there are some GPEs that only enabled
when the system is in sleep state, to wake the system backk from S3/S4.
But we are not touching these GPEs during transition to PM_SUSPEND_FREEZE.
This means we may lose some wake event.
But on the other hand, as we do not disable all the Interrupts during
PM_SUSPEND_FREEZE, we may get some extra "wakeup" Interrupts, that are
not available for S3/S4.
The patches has been tested on an old Sony laptop, and here are the results:
Average Power:
1. RPTM/idle for half an hour:
14.8W, 12.6W, 14.1W, 12.5W, 14.4W, 13.2W, 12.9W
2. Freeze for half an hour:
11W, 10.4W, 9.4W, 11.3W 10.5W
3. RTPM/idle for three hours:
11.6W
4. Freeze for three hours:
10W
5. Suspend to Memory:
0.5~0.9W
Average Resume Latency:
1. RTPM/idle with a black screen: (From pressing keyboard to screen back)
Less than 0.2s
2. Freeze: (From pressing power button to screen back)
2.50s
3. Suspend to Memory: (From pressing power button to screen back)
4.33s
>From the results, we can see that all the platforms should benefit from
this patch, even if it does not have Low Power S0.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Replace strict_strtoul() with kstrtoul() in pm_async_store() and
pm_qos_power_write().
[rjw: Modified subject and changelog.]
Signed-off-by: Daniel Walter <sahne@0x90.at>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Change the behavior of the newly introduced
/sys/power/pm_print_times attribute so that its initial value
depends on initcall_debug, but setting it to 0 will cause device
suspend/resume times not to be printed, even if initcall_debug has
been set. This way, the people who use initcall_debug for reasons
other than PM debugging will be able to switch the suspend/resume
times printing off, if need be.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Added a new knob called /sys/power/pm_print_times. Setting it to 1
enables printing of time taken by devices to suspend and resume.
Setting it to 0 disables this printing (unless overridden by
initcall_debug kernel command line option).
Signed-off-by: Sameer Nanda <snanda@chromium.org>
Acked-by: Greg KH <gregkh@linuxfoundation.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
The condition check in autosleep_store() is incorrect and prevents
/sys/power/autosleep from working as advertised. Fix that.
[rjw: Added the changelog.]
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
Android allows user space to manipulate wakelocks using two
sysfs file located in /sys/power/, wake_lock and wake_unlock.
Writing a wakelock name and optionally a timeout to the wake_lock
file causes the wakelock whose name was written to be acquired (it
is created before is necessary), optionally with the given timeout.
Writing the name of a wakelock to wake_unlock causes that wakelock
to be released.
Implement an analogous interface for user space using wakeup sources.
Add the /sys/power/wake_lock and /sys/power/wake_unlock files
allowing user space to create, activate and deactivate wakeup
sources, such that writing a name and optionally a timeout to
wake_lock causes the wakeup source of that name to be activated,
optionally with the given timeout. If that wakeup source doesn't
exist, it will be created and then activated. Writing a name to
wake_unlock causes the wakeup source of that name, if there is one,
to be deactivated. Wakeup sources created with the help of
wake_lock that haven't been used for more than 5 minutes are garbage
collected and destroyed. Moreover, there can be only WL_NUMBER_LIMIT
wakeup sources created with the help of wake_lock present at a time.
The data type used to track wakeup sources created by user space is
called "struct wakelock" to indicate the origins of this feature.
This version of the patch includes an rbtree manipulation fix from John Stultz.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: NeilBrown <neilb@suse.de>
|
|
Introduce a mechanism by which the kernel can trigger global
transitions to a sleep state chosen by user space if there are no
active wakeup sources.
It consists of a new sysfs attribute, /sys/power/autosleep, that
can be written one of the strings returned by reads from
/sys/power/state, an ordered workqueue and a work item carrying out
the "suspend" operations. If a string representing the system's
sleep state is written to /sys/power/autosleep, the work item
triggering transitions to that state is queued up and it requeues
itself after every execution until user space writes "off" to
/sys/power/autosleep.
That work item enables the detection of wakeup events using the
functions already defined in drivers/base/power/wakeup.c (with one
small modification) and calls either pm_suspend(), or hibernate() to
put the system into a sleep state. If a wakeup event is reported
while the transition is in progress, it will abort the transition and
the "system suspend" work item will be queued up again.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: NeilBrown <neilb@suse.de>
|
|
The enter_state() function in kernel/power/suspend.c should be
static and state_store() in kernel/power/suspend.c should call
pm_suspend() instead of it, so make that happen (which also reduces
code duplication related to suspend statistics).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
|
|
The code
if (error) {
suspend_stats.fail++;
dpm_save_failed_errno(error);
} else
suspend_stats.success++;
Appears in the kernel/power/main.c and kernel/power/suspend.c.
This patch just creates a new function to avoid duplicated code.
Suggested-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Marcos Paulo de Souza <marcos.mage@gmail.com>
Acked-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
The current device suspend/resume phases during system-wide power
transitions appear to be insufficient for some platforms that want
to use the same callback routines for saving device states and
related operations during runtime suspend/resume as well as during
system suspend/resume. In principle, they could point their
.suspend_noirq() and .resume_noirq() to the same callback routines
as their .runtime_suspend() and .runtime_resume(), respectively,
but at least some of them require device interrupts to be enabled
while the code in those routines is running.
It also makes sense to have device suspend-resume callbacks that will
be executed with runtime PM disabled and with device interrupts
enabled in case someone needs to run some special code in that
context during system-wide power transitions.
Apart from this, .suspend_noirq() and .resume_noirq() were introduced
as a workaround for drivers using shared interrupts and failing to
prevent their interrupt handlers from accessing suspended hardware.
It appears to be better not to use them for other porposes, or we may
have to deal with some serious confusion (which seems to be happening
already).
For the above reasons, introduce new device suspend/resume phases,
"late suspend" and "early resume" (and analogously for hibernation)
whose callback will be executed with runtime PM disabled and with
device interrupts enabled and whose callback pointers generally may
point to runtime suspend/resume routines.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
|
|
Using [un]lock_system_sleep() is safer than directly using mutex_[un]lock()
on 'pm_mutex', since the latter could lead to freezing failures. Hence convert
all the present users of mutex_[un]lock(&pm_mutex) to use these safe APIs
instead.
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
Lack of proper indentation of the goto statement decreases the readability
of code significantly. In fact, this made me look twice at the code to check
whether it really does what it should be doing. Fix this.
And in the same file, there are some extra whitespaces. Get rid of them too.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
After commit 2a77c46de1e3dace73745015635ebbc648eca69c
(PM / Suspend: Add statistics debugfs file for suspend to RAM)
a missing pair of braces inside the state_store() function causes even
invalid arguments to suspend to be wrongly treated as failed suspend
attempts. Fix this.
[rjw: Put the hash/subject of the buggy commit into the changelog.]
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
These files were getting <linux/module.h> via an implicit non-obvious
path, but we want to crush those out of existence since they cost
time during compiles of processing thousands of lines of headers
for no reason. Give them the lightweight header that just contains
the EXPORT_SYMBOL infrastructure.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Suspend statistics should depend on CONFIG_PM_SLEEP, so make that
happen.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
Record S3 failure time about each reason and the latest two failed
devices' names in S3 progress.
We can check it through 'suspend_stats' entry in debugfs.
The motivation of the patch:
We are enabling power features on Medfield. Comparing with PC/notebook,
a mobile enters/exits suspend-2-ram (we call it s3 on Medfield) far
more frequently. If it can't enter suspend-2-ram in time, the power
might be used up soon.
We often find sometimes, a device suspend fails. Then, system retries
s3 over and over again. As display is off, testers and developers
don't know what happens.
Some testers and developers complain they don't know if system
tries suspend-2-ram, and what device fails to suspend. They need
such info for a quick check. The patch adds suspend_stats under
debugfs for users to check suspend to RAM statistics quickly.
If not using this patch, we have other methods to get info about
what device fails. One is to turn on CONFIG_PM_DEBUG, but users
would get too much info and testers need recompile the system.
In addition, dynamic debug is another good tool to dump debug info.
But it still doesn't match our utilization scenario closely.
1) user need write a user space parser to process the syslog output;
2) Our testing scenario is we leave the mobile for at least hours.
Then, check its status. No serial console available during the
testing. One is because console would be suspended, and the other
is serial console connecting with spi or HSU devices would consume
power. These devices are powered off at suspend-2-ram.
Signed-off-by: ShuoX Liu <shuox.liu@intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
This enables pm_notifier_call_chain() to get the actual error code
in the callback rather than always assume -EINVAL by converting all
PM notifier calls to return encapsulate error code with
notifier_from_errno().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
Martin reports that on his system hibernation occasionally fails due
to the lack of memory, because the radeon driver apparently allocates
too much of it during the device freeze stage. It turns out that the
amount of memory allocated by radeon during hibernation (and
presumably during system suspend too) depends on the utilization of
the GPU (e.g. hibernating while there are two KDE 4 sessions with
compositing enabled causes radeon to allocate more memory than for
one KDE 4 session).
In principle it should be possible to use image_size to make the
memory preallocation mechanism free enough memory for the radeon
driver, but in practice it is not easy to guess the right value
because of the way the preallocation code uses image_size. For this
reason, it seems reasonable to allow users to control the amount of
memory reserved for driver allocations made after the hibernate
preallocation, which currently is constant and amounts to 1 MB.
Introduce a new sysfs file, /sys/power/reserved_size, whose value
will be used as the amount of memory to reserve for the
post-preallocation reservations made by device drivers, in bytes.
For backwards compatibility, set its default (and initial) value to
the currently used number (1 MB).
References: https://bugzilla.kernel.org/show_bug.cgi?id=34102
Reported-and-tested-by: Martin Steigerwald <Martin@Lichtvoll.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
|
|
The variable pm_flags is used to prevent APM from being enabled
along with ACPI, which would lead to problems. However, acpi_init()
is always called before apm_init() and after acpi_init() has
returned, it is known whether or not ACPI will be used. Namely, if
acpi_disabled is not set after acpi_init() has returned, this means
that ACPI is enabled. Thus, it is sufficient to check acpi_disabled
in apm_init() to prevent APM from being enabled in parallel with
ACPI.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Len Brown <len.brown@intel.com>
|
|
If direct references to pm_flags are removed from drivers/acpi/bus.c,
CONFIG_ACPI will not need to depend on CONFIG_PM any more. Make that
happen.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Len Brown <len.brown@intel.com>
|
|
There are two spellings in use for 'freeze' + 'able' - 'freezable' and
'freezeable'. The former is the more prominent one. The latter is
mostly used by workqueue and in a few other odd places. Unify the
spelling to 'freezable'.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Steven Whitehouse <swhiteho@redhat.com>
|
|
If the device which fails to resume is part of a loadable kernel module
it won't be checked at startup against the magic number stored in the
RTC.
Add a read-only sysfs attribute /sys/power/pm_trace_dev_match which
contains a list of newline separated devices (usually just the one)
which currently match the last magic number. This allows the device
which is failing to resume to be found after the modules are loaded
again.
Signed-off-by: James Hogan <james@albanarts.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
Yangtao Li
Pingfan Liu
Mauro Carvalho Chehab
Bart Van Assche
Srinivas Pandruvada
Rafael J. Wysocki
Arvind Yadav
Sudeep Holla
Lianwei Wang
Alexandra Yates
Zhonghui Fu
Kees Cook
Geert Uytterhoeven
Shuah Khan
Julius Werner
Li Fei
Zhang Rui
Daniel Walter
Rafael J. Wysocki
Sameer Nanda
Arve Hjønnevåg
Marcos Paulo de Souza
Srivatsa S. Bhat
Paul Gortmaker
ShuoX Liu
Akinobu Mita
Lucas De Marchi
Tejun Heo
James Hogan