| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This patch makes the i2c-bus property mandatory when using a device
tree. If the sfp i2c bus isn't described it's impossible to guess the
protocol to use for a given module, and the sfp module would then not
work in most cases.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case no Tx disable pin is available the SFP modules will always be
emitting. This could be an issue when using modules using laser as their
light source as we would have no way to disable it when the fiber is
removed. This patch adds a warning when registering an SFP cage which do
not have its tx_disable pin wired or available.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When NFP is modelled as a switch we assign phys_port_name to respective
port(representor )s:
vNIC0 - | - PF port (pf%d) MAC/PHY (p%d[s%d]) - |E==
In most cases there is only one vNIC for communication with the switch.
If there is more than one we need to be able to identify them. Use %d
as phys_port_name of the vNICs.
We don't have to pass ID to nfp_net_debugfs_vnic_add() separately any
more.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PCI PFs can host more than one logical endpoint. In NFP terms
this means having more than one vNIC for PCIe PF. The vNICs
are usually corresponding 1:1 to Ethernet ports. In core NIC
we use the legacy idea of vNIC *being* the Ethernet port,
hence netdevs put pX(sY) in their phys_port_name, like Ethernet
ports would. When ASIC ports are fully represented we need to
be able to name different PCIe PF ports, too. Use a scheme
similar to Ethernet ports - pfXsY, for PCIe PF number X,
sub-port Y.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current control firmware does not cater too well to multi-host
applications. There is no way to check which hosts are up or
otherwise negotiate what the state of the external port (the
Ethernet port) should be. Make sure the link is up when driver
loads, and don't take it down when Ethernet port netdev is
closed.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To configure buffering points we need full set of netdevs:
ASIC
user netdev -- | -- PCIe port MAC port -- | --
Configuring egrees qdiscs on user netdev configures standard
Linux TC software qdiscs, configuring PCIe port qdiscs will
provide a way of setting ASIC queuing parameters for PCIe block.
MAC port netdev egress qdiscs correspond to ASIC MAC Traffic
Manager block.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Our previous apps all assumed to use only one eswitch mode (legacy
or switchdev) without the ability to change it. ABM NIC will
want to support the switch so plumb devlink_eswitch_mode_set through.
The devlink_eswitch_mode_set is expected to spawn representors and
potentially devlink ports so it's called under big devlink lock and
pf->lock.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Changing switch mode may want to register and unregister devlink
ports. Therefore similarly to DEVLINK_CMD_PORT_SPLIT/UNSPLIT it
should not take the instance lock. Drivers don't depend on existing
locking since it's a very recent addition.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
nfp_apps can currently associate their structures with vNICs but
not representors. Add app priv pointer to representors as well.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ABM NIC requires more complex vNIC handling, allocate
per-vNIC structure. Find out RX queue base and PCI PF id.
There will be multiple PFs sharing the same MAC port, therefore
the MAC address assigned to the vNIC must be looked up in the
HWInfo database.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a very rudimentary active buffer management NIC support.
For now it's like a core NIC without SR-IOV support. Next
commits will extend its functionality.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current code doesn't enforce length requirements on 32bit accesses
with action NFP_CPP_ACTION_RW to memory units, but if the access
is only aligned to 4 bytes as well we will fall into the explicit
access case and error out. Such accesses are correct, allow them
by lowering the width earlier.
While at it use a switch statement to improve readability.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow app FW to advertise its shared buffer pool information.
Use the per-PF mailbox to configure them from devlink.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When working with devlink-related functionality for locking reasons
it's easier to create a new mailbox per-PCI PF device than try to
use one of the netdev/vNIC mailboxes.
Define new mailbox structure and resolve its symbol during probe.
For forward compatibility allow silent truncation of mailbox command
data.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
nfp_net_pf_rtsym_read_optional() and nfp_net_pf_map_rtsym() are not
really related to networking code. Move them to the PF code and
remove the net from their names. They will soon be needed by code
outside of nfp_net_main.c anyway.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bpfilter.ko consists of bpfilter_kern.c (normal kernel module code)
and user mode helper code that is embedded into bpfilter.ko
The steps to build bpfilter.ko are the following:
- main.c is compiled by HOSTCC into the bpfilter_umh elf executable file
- with quite a bit of objcopy and Makefile magic the bpfilter_umh elf file
is converted into bpfilter_umh.o object file
with _binary_net_bpfilter_bpfilter_umh_start and _end symbols
Example:
$ nm ./bld_x64/net/bpfilter/bpfilter_umh.o
0000000000004cf8 T _binary_net_bpfilter_bpfilter_umh_end
0000000000004cf8 A _binary_net_bpfilter_bpfilter_umh_size
0000000000000000 T _binary_net_bpfilter_bpfilter_umh_start
- bpfilter_umh.o and bpfilter_kern.o are linked together into bpfilter.ko
bpfilter_kern.c is a normal kernel module code that calls
the fork_usermode_blob() helper to execute part of its own data
as a user mode process.
Notice that _binary_net_bpfilter_bpfilter_umh_start - end
is placed into .init.rodata section, so it's freed as soon as __init
function of bpfilter.ko is finished.
As part of __init the bpfilter.ko does first request/reply action
via two unix pipe provided by fork_usermode_blob() helper to
make sure that umh is healthy. If not it will kill it via pid.
Later bpfilter_process_sockopt() will be called from bpfilter hooks
in get/setsockopt() to pass iptable commands into umh via bpfilter.ko
If admin does 'rmmod bpfilter' the __exit code bpfilter.ko will
kill umh as well.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce helper:
int fork_usermode_blob(void *data, size_t len, struct umh_info *info);
struct umh_info {
struct file *pipe_to_umh;
struct file *pipe_from_umh;
pid_t pid;
};
that GPLed kernel modules (signed or unsigned) can use it to execute part
of its own data as swappable user mode process.
The kernel will do:
- allocate a unique file in tmpfs
- populate that file with [data, data + len] bytes
- user-mode-helper code will do_execve that file and, before the process
starts, the kernel will create two unix pipes for bidirectional
communication between kernel module and umh
- close tmpfs file, effectively deleting it
- the fork_usermode_blob will return zero on success and populate
'struct umh_info' with two unix pipes and the pid of the user process
As the first step in the development of the bpfilter project
the fork_usermode_blob() helper is introduced to allow user mode code
to be invoked from a kernel module. The idea is that user mode code plus
normal kernel module code are built as part of the kernel build
and installed as traditional kernel module into distro specified location,
such that from a distribution point of view, there is
no difference between regular kernel modules and kernel modules + umh code.
Such modules can be signed, modprobed, rmmod, etc. The use of this new helper
by a kernel module doesn't make it any special from kernel and user space
tooling point of view.
Such approach enables kernel to delegate functionality traditionally done
by the kernel modules into the user space processes (either root or !root) and
reduces security attack surface of the new code. The buggy umh code would crash
the user process, but not the kernel. Another advantage is that umh code
of the kernel module can be debugged and tested out of user space
(e.g. opening the possibility to run clang sanitizers, fuzzers or
user space test suites on the umh code).
In case of the bpfilter project such architecture allows complex control plane
to be done in the user space while bpf based data plane stays in the kernel.
Since umh can crash, can be oom-ed by the kernel, killed by the admin,
the kernel module that uses them (like bpfilter) needs to manage life
time of umh on its own via two unix pipes and the pid of umh.
The exit code of such kernel module should kill the umh it started,
so that rmmod of the kernel module will cleanup the corresponding umh.
Just like if the kernel module does kmalloc() it should kfree() it
in the exit code.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Manish Rangankar <manish.rangankar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds callbacks for providing the ethernet protocol driver TLVs.
Signed-off-by: Manish Rangankar <manish.rangankar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds callbacks for providing the ethernet protocol driver TLVs.
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds callbacks for providing the ethernet protocol driver TLVs.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MFW requests the TLVs in interrupt context. Extracting of the required
data from upper layers and populating of the TLVs require process context.
The patch adds work-queues for processing the tlv requests. It also adds
the implementation for requesting the tlv values from appropriate protocol
driver.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patch adds driver support for processing TLV requests/repsonses
from the mfw and upper driver layers respectively. The implementation
reads the requested TLVs from the shared memory, requests the values
from upper layer drivers, populates this info (TLVs) shared memory and
notifies MFW about the TLV values.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patch adds required management firmware (MFW) interfaces such as
mailbox commands, TLV types etc.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ECN signals currently forces TCP to enter quickack mode for
up to 16 (TCP_MAX_QUICKACKS) following incoming packets.
We believe this is not needed, and only sending one immediate ack
for the current packet should be enough.
This should reduce the extra load noticed in DCTCP environments,
after congestion events.
This is part 2 of our effort to reduce pure ACK packets.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We want to add finer control of the number of ACK packets sent after
ECN events.
This patch is not changing current behavior, it only enables following
change.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Initial net_device implementation used ingress_lock spinlock to synchronize
ingress path of device. This lock was used in both process and bh context.
In some code paths action map lock was obtained while holding ingress_lock.
Commit e1e992e52faa ("[NET_SCHED] protect action config/dump from irqs")
modified actions to always disable bh, while using action map lock, in
order to prevent deadlock on ingress_lock in softirq. This lock was removed
from net_device, so disabling bh, while accessing action map, is no longer
necessary.
Replace all action idr spinlock usage with regular calls that do not
disable bh.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add IPv4 route tests covering add, append and replace permutations.
Assumes the ability to add a basic single path route works; this is
required for example when adding an address to an interface.
$ fib_tests.sh -t ipv4_rt
IPv4 route add / append tests
TEST: Attempt to add duplicate route - gw [ OK ]
TEST: Attempt to add duplicate route - dev only [ OK ]
TEST: Attempt to add duplicate route - reject route [ OK ]
TEST: Add new nexthop for existing prefix [ OK ]
TEST: Append nexthop to existing route - gw [ OK ]
TEST: Append nexthop to existing route - dev only [ OK ]
TEST: Append nexthop to existing route - reject route [ OK ]
TEST: Append nexthop to existing reject route - gw [ OK ]
TEST: Append nexthop to existing reject route - dev only [ OK ]
TEST: add multipath route [ OK ]
TEST: Attempt to add duplicate multipath route [ OK ]
TEST: Route add with different metrics [ OK ]
TEST: Route delete with metric [ OK ]
IPv4 route replace tests
TEST: Single path with single path [ OK ]
TEST: Single path with multipath [ OK ]
TEST: Single path with reject route [ OK ]
TEST: Single path with single path via multipath attribute [ OK ]
TEST: Invalid nexthop [ OK ]
TEST: Single path - replace of non-existent route [ OK ]
TEST: Multipath with multipath [ OK ]
TEST: Multipath with single path [ OK ]
TEST: Multipath with single path via multipath attribute [ OK ]
TEST: Multipath with reject route [ OK ]
TEST: Multipath - invalid first nexthop [ OK ]
TEST: Multipath - invalid second nexthop [ OK ]
TEST: Multipath - replace of non-existent route [ OK ]
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add IPv6 route tests covering add, append and replace permutations.
Assumes the ability to add a basic single path route works; this is
required for example when adding an address to an interface.
$ fib_tests.sh -t ipv6_rt
IPv6 route add / append tests
TEST: Attempt to add duplicate route - gw [ OK ]
TEST: Attempt to add duplicate route - dev only [ OK ]
TEST: Attempt to add duplicate route - reject route [ OK ]
TEST: Add new route for existing prefix (w/o NLM_F_EXCL) [ OK ]
TEST: Append nexthop to existing route - gw [ OK ]
TEST: Append nexthop to existing route - dev only [ OK ]
TEST: Append nexthop to existing route - reject route [ OK ]
TEST: Append nexthop to existing reject route - gw [ OK ]
TEST: Append nexthop to existing reject route - dev only [ OK ]
TEST: Add multipath route [ OK ]
TEST: Attempt to add duplicate multipath route [ OK ]
TEST: Route add with different metrics [ OK ]
TEST: Route delete with metric [ OK ]
IPv6 route replace tests
TEST: Single path with single path [ OK ]
TEST: Single path with multipath [ OK ]
TEST: Single path with reject route [ OK ]
TEST: Single path with single path via multipath attribute [ OK ]
TEST: Invalid nexthop [ OK ]
TEST: Single path - replace of non-existent route [ OK ]
TEST: Multipath with multipath [ OK ]
TEST: Multipath with single path [ OK ]
TEST: Multipath with single path via multipath attribute [ OK ]
TEST: Multipath with reject route [ OK ]
TEST: Multipath - invalid first nexthop [ OK ]
TEST: Multipath - invalid second nexthop [ OK ]
TEST: Multipath - replace of non-existent route [ OK ]
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add option to pause after each test before cleanup is done. Allows
user to do manual inspection or more ad-hoc testing after each test
with the setup in tact.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add command line options for controlling pause on fail, controlling
specific tests to run and verbose mode rather than relying on environment
variables.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As more tests are added, it is convenient to have a tally at the end.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bring consistency to ipv6 route replace and append semantics.
Remove rt6_qualify_for_ecmp which is just guess work. It fails in 2 cases:
1. can not replace a route with a reject route. Existing code appends
a new route instead of replacing the existing one.
2. can not have a multipath route where a leg uses a dev only nexthop
Existing use cases affected by this change:
1. adding a route with existing prefix and metric using NLM_F_CREATE
without NLM_F_APPEND or NLM_F_EXCL (ie., what iproute2 calls
'prepend'). Existing code auto-determines that the new nexthop can
be appended to an existing route to create a multipath route. This
change breaks that by requiring the APPEND flag for the new route
to be added to an existing one. Instead the prepend just adds another
route entry.
2. route replace. Existing code replaces first matching multipath route
if new route is multipath capable and fallback to first matching
non-ECMP route (reject or dev only route) in case one isn't available.
New behavior replaces first matching route. (Thanks to Ido for spotting
this one)
Note: Newer iproute2 is needed to display multipath routes with a dev-only
nexthop. This is due to a bug in iproute2 and parsing nexthops.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Handle append for gateway based routes. Dev-only multipath routes will
be handled by a follow on patch.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since we no longer use i as an array index for the data variable,
replace the use of 'j' with 'i' so that we match the general loop
variable name.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add documentation for the i40e_get_stats_count, i40e_get_stat_strings
and i40e_get_ethtool_stats explaining that the number and ordering of
statistics must remain constant for a given netdevice.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
A future patch is going to add a helper function i40e_add_ethtool_stats
that will help lower the amount of boiler plate code in the
i40e_get_ethtool_stats function.
This conversion will take place over many patches, and the helper
function will work by directly updating a reference to the data pointer.
Since this would not work combined with the current method of accessing
data like an array, update all the code that copies stats into the data
buffer to use direct updates to the pointer instead of array accesses.
This will prevent incorrect stat updates for patches in between the
conversion.
Similarly, when copying strings, we used a separate char *p pointer.
Instead, use the data pointer directly as it's already a (u8 *) type
which is the same size.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We always prefix these stats with a fixed string, so just fold this
prefix into the stat string definition. This preparatory work will make
it easier to implement a helper function to copy stats and strings into
the supplied buffers in a future patch.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We don't really want to use BUG_ON here since that would completely
crash the kernel, thus the reason we commented it out. We *can't* use
BUILD_BUG_ON because at least now (a) the sizes aren't constant (we are
fixing this) and (b) not all compilers are smart enough to understand
that "p - data" is a constant.
Instead, just use a WARN_ONCE so that the first time we end up with an
incorrect size we will dump a stack trace and a message, hopefully
highlighting the issues early in testing.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Split the statistic strings and private flags strings into their own
separate functions to aid code readability.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The ethtool API for obtaining device statistics is not intended to allow
runtime changes in the number of statistics reported. It may *appear*
this way, as there is an ability to request the number of stats using
ethtool_get_set_count(). However, it is expected that this must always
return the same value for invocations of the same device.
If we don't satisfy this contract, and allow the number of stats to
change during run time, we could cause invalid memory accesses or report
the stat strings incorrectly. This is because the API for obtaining
stats is to (1) get the size, (2) get the strings and finally (3) get
the stats. Since these are each separate ethtool op commands, it is not
possible to maintain consistency by holding the RTNL lock over the whole
operation. This results in the potential for a race condition to occur
where the size changed between any of the 3 calls.
Avoid this issue by requiring that we always return the same value for
a given device. We can check any values which remain constant for the
life of the device, but must not report different sizes depending on
runtime attributes.
This patch specifically fixes the queue statistics to always return
every queue even if it's not currently in use.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The ethtool API for obtaining device statistics is not intended to allow
runtime changes in the number of statistics reported. It may *appear*
this way, as there is an ability to request the number of stats using
ethtool_get_set_count(). However, it is expected that this must always
return the same value for invocations of the same device.
If we don't satisfy this contract, and allow the number of stats to
change during run time, we could cause invalid memory accesses or report
the stat strings incorrectly. This is because the API for obtaining
stats is to (1) get the size, (2) get the strings and finally (3) get
the stats. Since these are each separate ethtool op commands, it is not
possible to maintain consistency by holding the RTNL lock over the whole
operation. This results in the potential for a race condition to occur
where the size changed between any of the 3 calls.
Avoid this issue by requiring that we always return the same value for
a given device. We can check any values which remain constant for the
life of the device, but must not report different sizes depending on
runtime attributes.
This patch specifically fixes the VEB statistics strings to always be
reported. Other issues will be fixed in future patches.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Use the same logic to free the skb after clearing the Tx timestamp bit
lock in i40e_ptp_stop as we use in the other locations. It is not as
important here since we are not racing against a future Tx timestamp
request (as we are disabling PTP at this point). However it is good to
be consistent in how we approach the bit lock so that future callers
don't copy the old anti-pattern.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Now that we can compile test this driver on 64-bit hosts, we get some
warnings about how a pointer/address is written/read to/from a register
(sw_token). Fix this by doing the appropriate conversions, we cannot
possibly have the driver work on 64-bit hosts the way the tokens are
managed though, since the registers being written to a 32-bit only.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use %pa which is the correct formatter to print a physical address,
instead of %p which is just a pointer.
Fixes: a6286ee630f6 ("net: Add TI DaVinci EMAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When building on a 64-bit host we will get the following warning:
drivers/net/ethernet/ti/cpsw.c: In function 'cpsw_add_ch_strings':
drivers/net/ethernet/ti/cpsw.c:1284:19: warning: format '%d' expects
argument of type 'int', but argument 5 has type 'long unsigned int'
[-Wformat=]
"%s DMA chan %d: %s", rx_dir ? "Rx" : "Tx",
~^
%ld
Fix this by using an %ld format and casting to long.
Fixes: e05107e6b747 ("net: ethernet: ti: cpsw: add multi queue support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On 64-bit hosts we will get the following warning:
drivers/net/ethernet/ti/cpts.c: In function 'cpts_overflow_check':
drivers/net/ethernet/ti/cpts.c:297:11: warning: format '%lld' expects
argument of type 'long long int', but argument 3 has type
'__kernel_time_t {aka long int}' [-Wformat=]
pr_debug("cpts overflow check at %lld.%09lu\n", ts.tv_sec,
ts.tv_nsec);
Fix this by using an appropriate casting that works on all bit sizes.
Fixes: a5c79c26e168 ("ptp: cpts: convert to the 64 bit get/set time methods.")
Fixes: 87c0e764d43a ("cpts: introduce time stamping code and a PTP hardware clock.")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Antoine Tenart
Jakub Kicinski
Alexei Starovoitov
Manish Rangankar
Chad Dupuis
Sudarsana Reddy Kalluru
Eric Dumazet
Vlad Buslov
David Ahern
Jacob Keller
Florian Fainelli