| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
PCI devices that are 64-bit DMA capable should set the coherent
DMA mask as well as the streaming DMA mask. On some architectures,
these are managed separately, and so the coherent DMA mask will be
left at its default value of 32 if it is not set explicitly. This
results in errors such as
r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
hwdev DMA mask = 0x00000000ffffffff, dev_addr = 0x00000080fbfff000
swiotlb: coherent allocation failed for device 0000:02:00.0 size=4096
CPU: 0 PID: 1062 Comm: systemd-udevd Not tainted 4.8.0+ #35
Hardware name: AMD Seattle/Seattle, BIOS 10:53:24 Oct 13 2016
on systems without memory that is 32-bit addressable by PCI devices.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Check answers from USB stack and avoid re-sending the request
multiple times if the device does not respond.
This fixes the following problem, observed with a probably flaky adapter.
[62108.732707] usb 1-3: new high-speed USB device number 5 using xhci_hcd
[62108.914421] usb 1-3: New USB device found, idVendor=0b95, idProduct=7720
[62108.914463] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[62108.914476] usb 1-3: Product: AX88x72A
[62108.914486] usb 1-3: Manufacturer: ASIX Elec. Corp.
[62108.914495] usb 1-3: SerialNumber: 000001
[62114.109109] asix 1-3:1.0 (unnamed net_device) (uninitialized):
Failed to write reg index 0x0000: -110
[62114.109139] asix 1-3:1.0 (unnamed net_device) (uninitialized):
Failed to send software reset: ffffff92
[62119.109048] asix 1-3:1.0 (unnamed net_device) (uninitialized):
Failed to write reg index 0x0000: -110
...
Since the USB timeout is 5 seconds, and the operation is retried 30 times,
this results in
[62278.180353] INFO: task mtpd:1725 blocked for more than 120 seconds.
[62278.180373] Tainted: G W 3.18.0-13298-g94ace9e #1
[62278.180383] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
...
[62278.180957] kworker/2:0 D 0000000000000000 0 5744 2 0x00000000
[62278.180978] Workqueue: usb_hub_wq hub_event
[62278.181029] ffff880177f833b8 0000000000000046 ffff88017fd00000 ffff88017b126d80
[62278.181048] ffff880177f83fd8 ffff880065a71b60 0000000000013340 ffff880065a71b60
[62278.181065] 0000000000000286 0000000103b1c199 0000000000001388 0000000000000002
[62278.181081] Call Trace:
[62278.181092] [<ffffffff8e0971fd>] ? console_conditional_schedule+0x2c/0x2c
[62278.181105] [<ffffffff8e094f7b>] schedule+0x69/0x6b
[62278.181117] [<ffffffff8e0972e0>] schedule_timeout+0xe3/0x11d
[62278.181133] [<ffffffff8daadb1b>] ? trace_timer_start+0x51/0x51
[62278.181146] [<ffffffff8e095a05>] do_wait_for_common+0x12f/0x16c
[62278.181162] [<ffffffff8da856a7>] ? wake_up_process+0x39/0x39
[62278.181174] [<ffffffff8e095aee>] wait_for_common+0x52/0x6d
[62278.181187] [<ffffffff8e095b3b>] wait_for_completion_timeout+0x13/0x15
[62278.181201] [<ffffffff8de676ce>] usb_start_wait_urb+0x93/0xf1
[62278.181214] [<ffffffff8de6780d>] usb_control_msg+0xe1/0x11d
[62278.181230] [<ffffffffc037d629>] usbnet_write_cmd+0x9c/0xc6 [usbnet]
[62278.181286] [<ffffffffc03af793>] asix_write_cmd+0x4e/0x7e [asix]
[62278.181300] [<ffffffffc03afb41>] asix_set_sw_mii+0x25/0x4e [asix]
[62278.181314] [<ffffffffc03b001d>] asix_mdio_read+0x51/0x109 [asix]
...
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sparse was complaining when we went to prototype some code
using ethtool_cmd_speed_set and SPEED_100000, which uses
the upper 16 bits of __u32 speed for the first time.
CHECK
...
.../uapi/linux/ethtool.h:123:28: warning:
cast truncates bits from constant value (186a0 becomes 86a0)
The warning is actually bogus, as no bits are really lost, but
we can get rid of the sparse warning with this one small change.
Reported-by: Preethi Banala <preethi.banala@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In cases where the number of tx rings is not a multiple of the number of
rx rings, the tx completion event will be handled on a different core
from the transmit and population of the ring. Races on the ring will
lead to a double-free of the page, and possibly other corruption.
The rings are initialized by default with a valid multiple of rings,
based on the number of cpus, therefore an invalid configuration requires
ethtool to change the ring layout. For instance 'ethtool -L eth0 rx 9 tx
8' will cause packets received on rx0, and XDP_TX'd to tx48, to be
completed on cpu3 (48 % 9 == 3).
Resolve this discrepancy by shifting the irq for the xdp tx queues to
start again from 0, modulo rx_ring_num.
Fixes: 9ecc2d86171a ("net/mlx4_en: add xdp forwarding and data write support")
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Brenden Blanco <bblanco@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This cleans many of the warnings that would arise in qed as a
result of compilations with C=1; Most of those are the addition
of missing 'static' to functions, although there are several other
fixes as well.
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The qedr driver would require a tristate Kconfig option [to allow
it to compile as a module], and toward that end we've added the
INFINIBAND_QEDR option. But as we've made the compilation of the
qed/qede infrastructure required for RoCE dependent on the option
we'd be facing linking difficulties in case that QED=y or QEDE=y,
and INFINIBAND_QEDR=m.
To resolve this, we seperate between the INFINIBAND_QEDR option
and the infrastructure support in qed/qede by introducing a new
QED_RDMA option which would be selected by INFINIBAND_QEDR but would
be a boolean instead of a tristate; Following that, the qed/qede is
fixed based on this new option so that all config combinations would
be supported.
Fixes: cee9fbd8e2e9 ("qede: add qedr framework")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Smatch compains about qed_roce_ll2_tx() dereference
of the 'cdev' variable while testing its validity later.
As the validation checking is an over-kill [variable would always
be set], simply remove it.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: abd49676c707 ("qed: Add RoCE ll2 & GSI support")
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The IPv6 temporary address generation uses a variable called DESYNC_FACTOR
to prevent hosts updating the addresses at the same time. Quoting RFC 4941:
... The value DESYNC_FACTOR is a random value (different for each
client) that ensures that clients don't synchronize with each other and
generate new addresses at exactly the same time ...
DESYNC_FACTOR is defined as:
DESYNC_FACTOR -- A random value within the range 0 - MAX_DESYNC_FACTOR.
It is computed once at system start (rather than each time it is used)
and must never be greater than (TEMP_VALID_LIFETIME - REGEN_ADVANCE).
First, I believe the RFC has a typo in it and meant to say: "and must
never be greater than (TEMP_PREFERRED_LIFETIME - REGEN_ADVANCE)"
The reason is that at various places in the RFC, DESYNC_FACTOR is used in
a calculation like (TEMP_PREFERRED_LIFETIME - DESYNC_FACTOR) or
(TEMP_PREFERRED_LIFETIME - REGEN_ADVANCE - DESYNC_FACTOR). It needs to be
smaller than (TEMP_PREFERRED_LIFETIME - REGEN_ADVANCE) for the result of
these calculations to be larger than zero. It's never used in a
calculation together with TEMP_VALID_LIFETIME.
I already submitted an errata to the rfc-editor:
https://www.rfc-editor.org/errata_search.php?rfc=4941
The Linux implementation of DESYNC_FACTOR is very wrong:
max_desync_factor is used in places DESYNC_FACTOR should be used.
max_desync_factor is initialized to the RFC-recommended value for
MAX_DESYNC_FACTOR (600) but the whole point is to get a _random_ value.
And nothing ensures that the value used is not greater than
(TEMP_PREFERRED_LIFETIME - REGEN_ADVANCE), which leads to underflows. The
effect can easily be observed when setting the temp_prefered_lft sysctl
e.g. to 60. The preferred lifetime of the temporary addresses will be
bogus.
TEMP_PREFERRED_LIFETIME and REGEN_ADVANCE are not constants and can be
influenced by these three sysctls: regen_max_retry, dad_transmits and
temp_prefered_lft. Thus, the upper bound for desync_factor needs to be
re-calculated each time a new address is generated and if desync_factor is
larger than the new upper bound, a new random value needs to be
re-generated.
And since we already have max_desync_factor configurable per interface, we
also need to calculate and store desync_factor per interface.
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The randomized interface identifier (rndid) was periodically updated from
the regen_timer timer. Simplify the code by updating the rndid only when
needed by ipv6_try_regen_rndid().
This makes the follow-up DESYNC_FACTOR fix much simpler. Also it fixes a
reference counting error in this error path, where an in6_dev_put was
missing:
err = addrconf_sysctl_register(ndev);
if (err) {
ipv6_mc_destroy_dev(ndev);
- del_timer(&ndev->regen_timer);
snmp6_unregister_dev(ndev);
goto err_release;
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After the commit 9207f9d45b0a ("net: preserve IP control block
during GSO segmentation"), the GSO CB and the IPoIB CB conflict.
That destroy the IPoIB address information cached there,
causing a severe performance regression, as better described here:
http://marc.info/?l=linux-kernel&m=146787279825501&w=2
This change moves the data cached by the IPoIB driver from the
skb control lock into the IPoIB hard header, as done before
the commit 936d7de3d736 ("IPoIB: Stop lying about hard_header_len
and use skb->cb to stash LL addresses").
In order to avoid GRO issue, on packet reception, the IPoIB driver
stash into the skb a dummy pseudo header, so that the received
packets have actually a hard header matching the declared length.
To avoid changing the connected mode maximum mtu, the allocated
head buffer size is increased by the pseudo header length.
After this commit, IPoIB performances are back to pre-regression
value.
v2 -> v3: rebased
v1 -> v2: avoid changing the max mtu, increasing the head buf size
Fixes: 9207f9d45b0a ("net: preserve IP control block during GSO segmentation")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This fixes the following errors when trying to clone the urls:
Cloning into 'net'...
fatal: repository 'http://git.kernel.org/cgit/linux/kernel/git/davem/net.git/' not found
Cloning into 'net-next'...
fatal: repository 'http://git.kernel.org/cgit/linux/kernel/git/davem/net-next.git/' not found
Cloning into 'linux'...
fatal: repository 'http://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/' not found
Cloning into 'stable-queue'...
fatal: repository 'http://git.kernel.org/cgit/linux/kernel/git/stable/stable-queue.git/' not found
Signed-off-by: Alexander Alemayhu <alexander@alemayhu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver only has runtime but no build time dependency with FSL_SOC ||
ARCH_MXC || ARCH_LAYERSCAPE. So it can be built for testing purposes if
the COMPILE_TEST option is enabled.
This is useful to have more build coverage and make sure that the driver
is not affected by changes that could cause build regressions.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the device is registered via OF, the OF table is used to match the
driver instead of the SPI device ID table, but the entries in the later
are used as aliasses to load the module if the driver was not built-in.
This is because the SPI core always reports an SPI module alias instead
of an OF one, but that could change so it's better to always export it.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the driver is built as a module, module alias information isn't filled
so the module won't be autoloaded. Add a SPI device ID table and use the
MODULE_DEVICE_TABLE() macro so the information is exported in the module.
Before this patch:
$ modinfo drivers/net/wan/slic_ds26522.ko | grep alias
$
After this patch:
$ modinfo drivers/net/wan/slic_ds26522.ko | grep alias
alias: spi:ds26522
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The goal of the patch is to fix this scenario:
ip link add dummy1 type dummy
ip link set dummy1 up
ip link set lo down ; ip link set lo up
After that sequence, the local route to the link layer address of dummy1 is
not there anymore.
When the loopback is set down, all local routes are deleted by
addrconf_ifdown()/rt6_ifdown(). At this time, the rt6_info entry still
exists, because the corresponding idev has a reference on it. After the rcu
grace period, dst_rcu_free() is called, and thus ___dst_free(), which will
set obsolete to DST_OBSOLETE_DEAD.
In this case, init_loopback() is called before dst_rcu_free(), thus
obsolete is still sets to something <= 0. So, the function doesn't add the
route again. To avoid that race, let's check the rt6 refcnt instead.
Fixes: 25fb6ca4ed9c ("net IPv6 : Fix broken IPv6 routing table after loopback down-up")
Fixes: a881ae1f625c ("ipv6: don't call addrconf_dst_alloc again when enable lo")
Fixes: 33d99113b110 ("ipv6: reallocate addrconf router for ipv6 address when lo device up")
Reported-by: Francesco Santoro <francesco.santoro@6wind.com>
Reported-by: Samuel Gauthier <samuel.gauthier@6wind.com>
CC: Balakumaran Kannan <Balakumaran.Kannan@ap.sony.com>
CC: Maruthi Thotad <Maruthi.Thotad@ap.sony.com>
CC: Sabrina Dubroca <sd@queasysnail.net>
CC: Hannes Frederic Sowa <hannes@stressinduktion.org>
CC: Weilong Chen <chenweilong@huawei.com>
CC: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit ea3dc9601bda ("ip6_tunnel: Add support for wildcard tunnel
endpoints.") introduces support for wildcards in tunnels endpoints,
but in some rare circumstances ip6_tnl_lookup selects wrong tunnel
interface relying only on source or destination address of the packet
and not checking presence of wildcard in tunnels endpoints. Later in
ip6_tnl_rcv this packets can be dicarded because of difference in
ipproto even if fallback device have proper ipproto configuration.
This patch adds checks of wildcard endpoint in tunnel avoiding such
behavior
Fixes: ea3dc9601bda ("ip6_tunnel: Add support for wildcard tunnel endpoints.")
Signed-off-by: Vadim Fedorenko <junk@yandex-team.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When I added the multicast flood control flag, I also added an attribute
for it for sysfs similar to other flags, but I forgot to add it to
brport_attrs.
Fixes: b6cb5ac8331b ("net: bridge: add per-port multicast flood flag")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The dev parameter passed to __axienet_device_reset() is not used inside
the function, so remove it.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is supposed to loop 1000 times and then give up. The problem is
it's a post-op and after the loop we test if "loop" is zero when really
it would be -1. Fix this by making it a pre-op.
Fixes: 1b7c55c4538b ("liquidio: CN23XX queue manipulation")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The "vf_vlan_info" struct ends with a 2 byte struct hole so we have to
memset it to ensure that no stack information is revealed to user space.
Fixes: 79aab093a0b5 ('net: Update API for VF vlan protocol 802.1ad support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We should clear out the padding and unused struct members so that we
don't expose stack information to userspace.
Fixes: fdb3accc2c15 ('tipc: add the ability to get UDP options via netlink')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit e0d56fdd7342 was a bit aggressive removing l3mdev calls in
the IPv4 stack. If the fib_lookup fails we do not want to drop to
make_route if the oif is an l3mdev device.
Also reverts 19664c6a0009 ("net: l3mdev: Remove netif_index_is_l3_master")
which removed netif_index_is_l3_master.
Fixes: e0d56fdd7342 ("net: l3mdev: remove redundant calls")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
call->operation_ID is sometimes being used as __be32 sometimes is being
used as u32. Be consistent and settle on using as u32.
Signed-off-by: David Howells <dhowells@redhat.com.
|
|
The phy_start() is used to indicate the PHY is now ready to do its
work. The state is changed, normally to PHY_UP which means that both
the MAC and the PHY are ready.
If the phy driver is using polling, when the next poll happens, the
state machine notices the PHY is now in PHY_UP, and kicks off
auto-negotiation, if needed.
If however, the PHY is using interrupts, there is no polling. The phy
is stuck in PHY_UP until the next interrupt comes along. And there is
no reason for the PHY to interrupt.
Have phy_start() schedule the state machine to run, which both speeds
up the polling use case, and makes the interrupt use case actually
work.
This problems exists whenever there is a state change which will not
cause an interrupt. Trigger the state machine in these cases,
e.g. phy_error().
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: Kyle Roeschley <kyle.roeschley@ni.com>
Tested-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Baozeng Ding reported following KASAN splat :
BUG: KASAN: use-after-free in ip6_datagram_recv_specific_ctl+0x13f1/0x15c0 at addr ffff880029c84ec8
Read of size 1 by task poc/25548
Call Trace:
[<ffffffff82cf43c9>] dump_stack+0x12e/0x185 /lib/dump_stack.c:15
[< inline >] print_address_description /mm/kasan/report.c:204
[<ffffffff817ced3b>] kasan_report_error+0x48b/0x4b0 /mm/kasan/report.c:283
[< inline >] kasan_report /mm/kasan/report.c:303
[<ffffffff817ced9e>] __asan_report_load1_noabort+0x3e/0x40 /mm/kasan/report.c:321
[<ffffffff85c71da1>] ip6_datagram_recv_specific_ctl+0x13f1/0x15c0 /net/ipv6/datagram.c:687
[<ffffffff85c734c3>] ip6_datagram_recv_ctl+0x33/0x40
[<ffffffff85c0b07c>] do_ipv6_getsockopt.isra.4+0xaec/0x2150
[<ffffffff85c0c7f6>] ipv6_getsockopt+0x116/0x230
[<ffffffff859b5a12>] tcp_getsockopt+0x82/0xd0 /net/ipv4/tcp.c:3035
[<ffffffff855fb385>] sock_common_getsockopt+0x95/0xd0 /net/core/sock.c:2647
[< inline >] SYSC_getsockopt /net/socket.c:1776
[<ffffffff855f8ba2>] SyS_getsockopt+0x142/0x230 /net/socket.c:1758
[<ffffffff8685cdc5>] entry_SYSCALL_64_fastpath+0x23/0xc6
Memory state around the buggy address:
ffff880029c84d80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ffff880029c84e00: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> ffff880029c84e80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
^
ffff880029c84f00: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ffff880029c84f80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
He also provided a syzkaller reproducer.
Issue is that ip6_datagram_recv_specific_ctl() expects to find IP6CB
data that was moved at a different place in tcp_v6_rcv()
This patch moves tcp_v6_restore_cb() up and calls it from
tcp_v6_do_rcv() when np->pktoptions is set.
Fixes: 971f10eca186 ("tcp: better TCP_SKB_CB layout to reduce cache line misses")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Baozeng Ding <sploving1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based upon v2 of Stephen's patch.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Wiht the latest rework of the xen-netback driver, we get a warning
on ARM about the types passed into min():
drivers/net/xen-netback/rx.c: In function 'xenvif_rx_next_chunk':
include/linux/kernel.h:739:16: error: comparison of distinct pointer types lacks a cast [-Werror]
The reason is that XEN_PAGE_SIZE is not size_t here. There
is no actual bug, and we can easily avoid the warning using the
min_t() macro instead of min().
Fixes: eb1723a29b9a ("xen-netback: refactor guest rx")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes a problem when propagated the
failure of ptp_clock_register to open function.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre TORGUE <alexandre.torgue@st.com>
Cc: Rayagond Kokatanur <rayagond@vayavyalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The gmac 4.x version has not extended descriptors
(that are available on 3.x instead of).
While initializing the PTP module, the advanced PTP was
enabled in case of extended descriptors. This cannot be
applied for 4.x version where only the hardware capability
register has to show if the feature is present.
Patch also adds some extra netdev_(debug/inof) to better
dump the configuration.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre TORGUE <alexandre.torgue@st.com>
Cc: Rayagond Kokatanur <rayagond@vayavyalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The definition of qed_get_rdma_ops() is not a prototype unless
we add 'void' here, as indicated by this W=1 warning:
drivers/net/ethernet/qlogic/qed/qed_roce.c: In function ‘qed_get_rdma_ops’:
drivers/net/ethernet/qlogic/qed/qed_roce.c:2950:28: error: old-style function definition [-Werror=old-style-definition]
Fixes: abd49676c707 ("qed: Add RoCE ll2 & GSI support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The software calculation of UDP checksum in Netvsc driver was
only handling IPv4 case. By using skb_checksum_help() instead
all protocols can be handled. Rearrange code to eliminate goto
and look like other drivers.
This is a temporary solution; recent versions of Window Server etc
do support UDP checksum offload, just need to do the appropriate negotiation
with host to validate before using. This will be done in later patch.
Please queue this for -stable as well.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Krister reported a kernel NULL pointer dereference after
tcf_action_init_1() invokes a_o->init(), it is a race condition
where one thread calling tcf_register_action() to initialize
the netns data after putting act ops in the global list and
the other thread searching the list and then calling
a_o->init(net, ...).
Fix this by moving the pernet ops registration before making
the action ops visible. This is fine because: a) we don't
rely on act_base in pernet ops->init(), b) in the worst case we
have a fully initialized netns but ops is still not ready so
new actions still can't be created.
Reported-by: Krister Johansen <kjlx@templeofstupid.com>
Tested-by: Krister Johansen <kjlx@templeofstupid.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If a VIF has been ready for rx_stall_timeout (60s by default) and an
Rx ring is drained of all requests an Rx stall will be incorrectly
detected. When this occurs and the guest Rx queue is empty, the Rx
ring's event index will not be set and the frontend will not raise an
event when new requests are placed on the ring, permanently stalling
the VIF.
This is a regression introduced by eb1723a29b9a7 (xen-netback:
refactor guest rx).
Fix this by reinstating the setting of queue->last_rx_time when
placing a packet onto the guest Rx ring.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The reserved field precise_offset->rsv is not cleared before being
copied to user space, leaking kernel stack memory. Clear the struct
before it's copied.
Signed-off-by: Vlad Tsyrklevich <vlad@tsyrklevich.net>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I am hitting this in mlx5:
drivers/net/ethernet/mellanox/mlx5/core/pagealloc.c: In function
reclaim_pages_cmd.clone.0:
drivers/net/ethernet/mellanox/mlx5/core/pagealloc.c:346: error: call
to __compiletime_assert_346 declared with attribute error:
BUILD_BUG_ON failed: __mlx5_bit_off(manage_pages_out, pas[i]) % 64
drivers/net/ethernet/mellanox/mlx5/core/pagealloc.c: In function give_pages:
drivers/net/ethernet/mellanox/mlx5/core/pagealloc.c:291: error: call
to __compiletime_assert_291 declared with attribute error:
BUILD_BUG_ON failed: __mlx5_bit_off(manage_pages_in, pas[i]) % 64
Problem is that this is doing a BUILD_BUG_ON on a non-constant
expression because of trying to take offset of pas[i] in the
structure.
Fix is to create MLX5_ARRAY_SET64 that takes an additional argument
that is the field index to separate between BUILD_BUG_ON on the array
constant field and the indexed field to assign the value to.
There are two callers of MLX5_SET64 that are trying to get a variable
offset, change those to call MLX5_ARRAY_SET64 passing 'pas' and 'i'
as the arguments to use in the offset check and the indexed value
assignment.
Fixes: a533ed5e179cd ("net/mlx5: Pages management commands via mlx5 ifc")
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Quectel EC21 and EC25 need the same "set DTR" request as devices
based on the MDM9230 chipset, but has no USB3 support. Our best guess
is that the "set DTR" functionality depends on chipset and/or
baseband firmware generation. But USB3 is still an optional feature.
Since we cannot enable this unconditionally for all older devices, and
there doesn't appear to be anything we can use in the USB descriptors
to identify these chips, we are forced to use a device specific quirk
flag.
Reported-and-tested-by: Sebastian Sjoholm <sebastian.sjoholm@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The internal device does support 802.1AD offloading since 018c1dda5ff1
("openvswitch: 802.1AD Flow handling, actions, vlan parsing, netlink
attributes").
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Acked-by: Eric Garver <e@erig.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the packet has its vlan tag in skb->vlan_tci, the length of the VLAN
header is not counted in skb->len. It doesn't make sense to subtract it.
Fixes: 018c1dda5ff1 ("openvswitch: 802.1AD Flow handling, actions, vlan parsing, netlink attributes")
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Acked-by: Eric Garver <e@erig.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This code is called whenever flow key is being extracted from the packet.
The packet may be as likely vlan tagged as not.
Fixes: 018c1dda5ff1 ("openvswitch: 802.1AD Flow handling, actions, vlan parsing, netlink attributes")
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Acked-by: Eric Garver <e@erig.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since we will remove items off the list using list_del() we need
to use a safe version of the list_for_each_entry() macro aptly named
list_for_each_entry_safe().
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While build testing with randconfig on x86, I ran into this warning
that appears to have been around forever
drivers/net/ethernet/ti/tlan.c: In function ‘tlan_probe1’:
drivers/net/ethernet/ti/tlan.c:614:1: error: label ‘err_out’ defined but not used [-Werror=unused-label]
This can be trivially avoided by just moving the label into the
existing #ifdef.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is useful to be able to see the hash configuration when running tests.
This patch adds a debugfs node for that purpose.
The original version of this patch (commit c0c64c152389) was reverted due
to build failures caused by a conflict with commit 0364a8824c02
("xen-netback: switch to threaded irq for control ring"). This new version
of the patch is nearly identical to the original, the only difference
being that creation of the debugfs node is predicated on 'ctrl_irq' being
non-zero rather then the now non-existent 'ctrl_task'.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: David S. Miller <davem@davemloft.net>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are two ways to get tc filters from kernel to user space.
1) Full dump (tc_dump_tfilter())
2) RTM_GETTFILTER to get one precise filter, reducing overhead.
The second operation is unfortunately broadcasting its result,
polluting "tc monitor" users.
This patch makes sure only the requester gets the result, using
netlink_unicast() instead of rtnetlink_send()
Jamal cooked an iproute2 patch to implement "tc filter get" operation,
but other user space libraries already use RTM_GETTFILTER when a single
filter is queried, instead of dumping all filters.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SDIO ID 0271:0418
Signed-off-by: Alan Cox <alan@linux.intel.com>
Bugzilla-ID: https://bugzilla.kernel.org/show_bug.cgi?id=67921
Reviewed-by: Steve deRosier <steve.derosier@lairdtech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This reverts commit 171f6402e4aa ("ath9k_hw: implement temperature compensation
support for AR9003+"). Some users report that this commit causes a regression
in performance under some conditions.
Fixes: 171f6402e4aa ("ath9k_hw: implement temperature compensation support for AR9003+")
Cc: <stable@vger.kernel.org> # 4.8
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[kvalo@qca.qualcomm.com: improve commit log]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Commit 0b8e3c4ca29f ("ath10k: move cal data len to hw_params") broke retrieving
the calibration data from cal_data debugfs file. The length of file was always
zero. The reason is:
static ssize_t ath10k_debug_cal_data_read(struct file *file,
char __user *user_buf,
size_t count, loff_t *ppos)
{
struct ath10k *ar = file->private_data;
void *buf = file->private_data;
This is obviously bogus, private_data cannot contain both struct ath10k and the
buffer. Fix it by caching calibration data to ar->debug.cal_data. This also
allows it to be accessed when the device is not active (interface is down).
The cal_data buffer is fixed size because during the first firmware probe we
don't yet know what will be the lenght of the calibration data. It was simplest
just to use a fixed length. There's a WARN_ON() in
ath10k_debug_cal_data_fetch() if the buffer is too small.
Tested with qca988x and firmware 10.2.4.70.56.
Reported-by: Nikolay Martynov <mar.kolya@gmail.com>
Fixes: 0b8e3c4ca29f ("ath10k: move cal data len to hw_params")
Cc: stable@vger.kernel.org # 4.7+
Signed-off-by: Marty Faltesek <mfaltesek@google.com>
[kvalo@qca.qualcomm.com: improve commit log and minor other changes]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
In commit d86e64768859 ("rtlwifi: rtl818x: constify local structures"),
the configuration struct for most of the drivers was changed to be
constant. The problem is that five of the modified drivers need to be
able to update the firmware name based on the exact model of the card.
As the file names were stored in one of the members of that struct,
these drivers would fail with a kernel BUG splat when they tried to
update the firmware name.
Rather than reverting the previous commit, I used a suggestion by
Johannes Berg and made the firmware file name pointers be local to
the routines that update the software variables.
The configuration struct of rtl8192cu, which was not touched in the
previous patch, is now constantfied.
Fixes: d86e64768859 ("rtlwifi: rtl818x: constify local structures")
Suggested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> # 4.8
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
ip6_route_output() doesn't return a negative error when it fails, rather
the ->error field of the returned dst_entry struct needs to be checked.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 75b54cb57ca3 ("rxrpc: Add IPv6 support")
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
Fix the following checker warning:
net/rxrpc/call_object.c:279 rxrpc_new_client_call()
warn: passing zero to 'ERR_PTR'
where a value that's always zero is passed to ERR_PTR() so that it can be
passed to a tracepoint in an auxiliary pointer field.
Just pass NULL instead to the tracepoint.
Fixes: a84a46d73050 ("rxrpc: Add some additional call tracing")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
We switched from kmap_atomic() to kmap() so the kunmap() calls need to
be updated to match.
Fixes: d001648ec7cf ('rxrpc: Don't expose skbs to in-kernel users [ver #2]')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David Howells <dhowells@redhat.com>
|
Ard Biesheuvel
Guenter Roeck
Jesse Brandeburg
Brenden Blanco
Yuval Mintz
Jiri Bohac
Paolo Abeni
Alexander Alemayhu
Javier Martinez Canillas
Nicolas Dichtel
Vadim Fedorenko
Nikolay Aleksandrov
Tobias Klauser
Dan Carpenter
David Ahern
David Howells
Andrew Lunn
Eric Dumazet
David S. Miller
Arnd Bergmann
Giuseppe CAVALLARO
stephen hemminger
WANG Cong
David Vrabel
Vlad Tsyrklevich
Tom Herbert
Bjørn Mork
Jiri Benc
Wei Yongjun
Paul Durrant
Adam Williamson
Felix Fietkau
Marty Faltesek
Larry Finger