aboutsummaryrefslogtreecommitdiffstats
path: root/mm/vmalloc.c (unfollow)
AgeCommit message (Collapse)AuthorFilesLines
2019-12-19nfp: flower: support ipv6 tunnel keep-alive messages from fwJohn Hurley4-0/+67
FW sends an update of IPv6 tunnels that are active in a given period. Use this information to update the kernel table so that neighbour entries do not time out when active on the NIC. Signed-off-by: John Hurley <john.hurley@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-19nfp: flower: handle notifiers for ipv6 route changesJohn Hurley2-68/+181
A notifier is used to track route changes in the kernel. If a change is made to a route that is offloaded to fw then an update is sent to the NIC. The driver tracks all routes that are offloaded to determine if a kernel change is of interest. Extend the notifier to track IPv6 route changes and create a new list that stores offloaded IPv6 routes. Modify the IPv4 route helper functions to accept varying address lengths. This way, the same core functions can be used to handle IPv4 and IPv6. Signed-off-by: John Hurley <john.hurley@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-19nfp: flower: handle ipv6 tunnel no neigh requestJohn Hurley4-8/+116
When fw does not know the next hop for an IPv6 tunnel, it sends a request to the driver. Handle this request by doing a route lookup on the IPv6 address and offloading the next hop to the fw neighbour table. Similar functions already exist to handle IPv4 no neighbour requests. To avoid confusion, append these functions with the _ipv4 tag. There is no change in functionality with this. Signed-off-by: John Hurley <john.hurley@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-19nfp: flower: modify pre-tunnel and set tunnel action for ipv6John Hurley3-30/+62
The IPv4 set tunnel action allows the setting of tunnel metadata such as the TTL and ToS values. The pre-tunnel action includes the destination IP address and is used to calculate the next hop from from the neighbour table. Much of the IPv4 tunnel actions can be reused for IPv6 tunnels. Change the names of associated functions and structs to remove the IPv4 identifier and make minor modifcations to support IPv6 tunnel actions. Ensure the pre-tunnel action contains the IPv6 address along with an identifying flag when an IPv6 tunnel action is required. Signed-off-by: John Hurley <john.hurley@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-19nfp: flower: offload list of IPv6 tunnel endpoint addressesJohn Hurley5-1/+141
Fw requires a list of IPv6 addresses that are used as tunnel endpoints to enable correct decap of tunneled packets. Store a list of IPv6 endpoints used in rules with a ref counter to track how many times it is in use. Offload the entire list any time a new IPv6 address is added or when an address is removed (ref count is 0). Signed-off-by: John Hurley <john.hurley@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-19nfp: flower: compile match for IPv6 tunnelsJohn Hurley4-51/+246
IPv6 tunnel matches are now supported by firmware. Modify the NFP driver to compile these match rules. IPv6 matches are handled similar to IPv4 tunnels with the difference the address length. The type of tunnel is indicated by the same bitmap that is used in IPv4 with an extra bit signifying that the IPv6 variation should be used. Only compile IPv6 tunnel matches when the fw features symbol indicated that they are compatible with the currently loaded fw. Signed-off-by: John Hurley <john.hurley@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-19nfp: flower: move udp tunnel key match compilation to helper functionJohn Hurley1-22/+35
IPv4 UDP and GRE tunnel match rule compile helpers share functions for compiling fields such as IP addresses. However, they handle fields such tunnel IDs differently. Create new helper functions for compiling GRE and UDP tunnel key data. This is in preparation for supporting IPv6 tunnels where these new functions can be reused. This patch does not change functionality. Signed-off-by: John Hurley <john.hurley@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-19nfp: flower: pass flow rule pointer directly to match functionsJohn Hurley1-49/+27
In kernel 5.1, the flow offload API was introduced along with a helper function to extract the flow_rule from the TC offload struct. Each of the match helper functions are passed the offload struct and extract the flow rule to a local variable. Simplify the code while also removing the extra compat and local variable calls by extracting the rule once in the main match handler, and passing a reference to the rule direct to each helper. This patch does not change driver functionality. Signed-off-by: John Hurley <john.hurley@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-19hdlcdrv: replace unnecessary assertion in hdlcdrv_registerAditya Pakki1-2/+0
In hdlcdrv_register, failure to register the driver causes a crash. The three callers of hdlcdrv_register all pass valid pointers and do not fail. The patch eliminates the unnecessary BUG_ON assertion. Signed-off-by: Aditya Pakki <pakki001@umn.edu> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-19net: mvpp2: cycle comphy to power it downRussell King1-0/+10
Presently, at boot time, the comphys are enabled. For firmware compatibility reasons, the comphy driver does not power down the comphys at boot. Consequently, the ethernet comphys are left active until the network interfaces are brought through an up/down cycle. If the port is never used, the port wastes power needlessly. Arrange for the ethernet comphys to be cycled by the mvpp2 driver as if the interface went through an up/down cycle during driver probe, thereby powering them down. This saves: 270mW per 10G SFP+ port on the Macchiatobin Single Shot (eth0/eth1) 370mW per 10G PHY port on the Macchiatobin Double Shot (eth0/eth1) 160mW on the SFP port on either Macchiatobin flavour (eth3) Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Acked-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-19net: sfp: report error on failure to read sfp soft statusRussell King1-2/+9
Report a rate-limited error if we fail to read the SFP soft status, and preserve the current status in that case. This avoids I2C bus errors from triggering a link flap. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-19net: phy: marvell: use genphy_check_and_restart_aneg()Russell King1-20/+1
Use the helper to check and restart autonegotiation for the marvell fiber page negotiation setting. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-19net: phy: marvell: use phy_modify_changed()Russell King1-16/+10
Use phy_modify_changed() to change the fiber advertisement register rather than open coding this functionality. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-19net: phy: marvell: use existing clause 37 definitionsRussell King1-18/+8
Use existing clause 37 advertising/link partner definitions rather than private ones for the advertisement registers. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-19net: phy: marvell: consolidate phy status readingRussell King1-43/+17
marvell_read_status_page_an() always reads the PHY status register, but marvell_update_link() has already done this. Rather than wastefully reading the register twice in quick succession, read it once in marvell_read_status_page() and use the result for both. This makes marvell_update_link() rather pointless, so move it into marvell_read_status_page(). Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-19net: phy: marvell: use positive logic for link stateRussell King1-4/+3
Rather than using negative logic: if (there is no link) set link = 0 else set link = 1 use the more natural positive logic: if (there is link) set link = 1 else set link = 0 Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-19net: phy: marvell: initialise link partner state earlierRussell King1-20/+5
Move the initialisation of the link partner state earlier, inside marvell_read_status_page(), so we don't have the same initialisation scattered amongst the other files. This is in a similar place to the genphy implementation, so would result in the same behaviour if a PHY read error occurs. This allows us to get rid of marvell_read_status_page_fixed(), which became a pointless wrapper around genphy_read_status_fixed(). Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-19net: phy: marvell: rearrange to use genphy_read_lpa()Russell King1-34/+32
Rearrange the Marvell PHY driver to use genphy_read_lpa() rather than open-coding this functionality. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-19net: phy: provide and use genphy_read_status_fixed()Russell King4-47/+41
There are two drivers and generic code which contain exactly the same code to read the status of a PHY operating without autonegotiation enabled. Rather than duplicate this code, provide a helper to read this information. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-19net: phy: add genphy_check_and_restart_aneg()Russell King2-17/+32
Add a helper for restarting autonegotiation(), similar to the clause 45 variant. Use it in __genphy_config_aneg() Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-19net: phy: use phy_resolve_aneg_pause()Russell King3-14/+3
Several drivers code their own version of this, working from the LPA register, after setting the ethtool link partner advertisement bitmask. Use the generic function instead. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-19net: phy: remove redundant .aneg_done initialisersRussell King2-7/+0
Remove initialisers that set .aneg_done to genphy_aneg_done - this is the default for clause 22 PHYs, so the initialiser is redundant. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-18net: stmmac: tc: Fix TAPRIO division operationJose Abreu1-2/+4
For ARCHs that don't support 64 bits division we need to use the helpers. Fixes: b60189e0392f ("net: stmmac: Integrate EST with TAPRIO scheduler API") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>