Age | Commit message (Collapse) | Author | Files | Lines |
|
Up until now we had two interfaces for neighbour related configuration:
ndo_neigh_{construct,destroy} and NEIGH_UPDATE netevents. The ndos were
used to add and remove neighbours from the driver's cache, whereas the
netevent was used to reflect the neighbours into the device's tables.
However, if the NUD state of a neighbour isn't NUD_VALID or if the
neighbour is dead, then there's really no reason for us to keep it
inside our cache. The only exception to this rule are neighbours that
are also used for nexthops, which we periodically refresh to get them
resolved.
We can therefore eliminate the ndo entry point into the driver and
simplify the code, making it similar to the FIB reflection, which is
based solely on events. This also helps us avoid a locking issue, in
which the RIF cache was traversed without proper locking during
insertion into the neigh entry cache.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 33b1341cd1bf ("mlxsw: spectrum_router: Fix handling of
neighbour structure") we no longer use destination IP for neighbour
lookup, so remove it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We currently associate each neighbour entry with a work item, so it's
not possible to have multiple events queued for the same neighbour
entry. However, this is about to be changed so that the neighbour entry
is only resolved when the work item is scheduled.
The above can result in a mismatch between the kernel's and the device's
neighbour table, unless the associated work items are processed in the
order in which they were submitted.
Do that by migrating the NEIGH_UPDATE work items to be processed in the
ordered workqueue which was recently introduced in mlxsw in commit
a3832b31898f ("mlxsw: core: Create an ordered workqueue for FIB
offload").
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We always use zero delay before queueing a work on the ordered workqueue
('mlxsw_owq'), so use work_struct directly instead of delayable work.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
HTGT register length is limited to 32 bytes and not 256 bytes.
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mvneta itself does not support WOL, but the PHY might.
So pass the calls to the PHY
Signed-off-by: Jingju Hou <houjingj@marvell.com>
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch switches the imx6 and vf610 based SoCs from the hardware FIFO
to the timestamp based rx offloading.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The flexcan IP core has 64 mailboxes. For now they are configured for
RX as a hardware FIFO. This FIFO has a fixed depth of 6 CAN frames. In
some high load scenarios it turns out thas this buffer is too small.
In order to have a buffer larger than the 6 frames FIFO, this patch adds
support for timestamp based offloading via the generic rx-offload
infrastructure.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In order to receive RTR frames in the non HW FIFO mode the RSS and EACEN bits
of the reg_ctrl2 have to be activated. As this has no side effect in the FIFO
mode, we do this unconditionally on cores with the reg_ctrl2.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Modern flexcan IP cores support two RX modes. One is using the 6 fames deep
hardware FIFO, the other is using up to 64 mailboxes (in non FIFO mode). For
now only the HW FIFO mode is activated.
In order to make use of the RX mailboxes the individual RX masking feature has
to be activated, otherwise matching mailboxes are overwritten during the
reception process. This however switches on the individual RX masking, which
uses reg_rximr registers for masking.
This patch activates the individual RX masking feature unconditionally and
initializes the mask registers (reg_rximr) with 0x0 == "don't care", which
switches off any filtering.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch converts the flexcan driver to make use of the rx-offload
can_rx_offload_irq_offload_fifo() helper function. The idea is to read
the CAN frames already in the interrupt context, as the depth of the
flexcan HW FIFO is too shallow, resulting in too many missed frames.
During a normal NAPI poll the frames are the pushed into the upper
layers.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch makes the TX mailbox selectable duing runtime. This is a preparation
patch to use of the hardware FIFO selectable via runtime. As the TX mailbox
number is different in HW FIFO and normal mode.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch converts the define FLEXCAN_IFLAG_DEFAULT into the runtime
calculated value priv->reg_imask1_default. This is a preparation patch to make
the TX mailbox selectable during runtime, too.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch changes the flexcan_irq() function to only return
IRQ_HANDLED, if the interrupt really has been handled, otherwise
IRQ_NONE is returned.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch folds in the do_bus_err() function into
flexcan_poll_bus_err().
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch removed the not needed initialisation from the new_state,
rx_state, tx_state variabled.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch converts the rx_errors and tx_errors from int into bool
values, to reflect their actual meaning.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch changes the declaration of the devtype data to const.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch removes the write only member pdata from the struct
flexcan_priv.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch adds some missing register definitions, which are needed in an
upcoming patch.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Some CAN controllers don't implement a FIFO in hardware, but fill their
mailboxes in a particular order (from lowest to highest or highest to lowest).
This makes problems to read the frames in the correct order from the hardware,
as new frames might be filled into just read (low) mailboxes. This gets worse,
when following new frames are received into not read (higher) mailboxes.
On the bright side some these CAN controllers put a timestamp on each received
CAN frame. This patch adds support to offload CAN frames in interrupt context,
order them by timestamp and then transmitted in a NAPI context.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Some CAN controllers have a usable FIFO already but can still benefit
from off-loading the CAN controller FIFO. The CAN frames of the FIFO are
read and put into a skb queue during interrupt and then transmitted in a
NAPI context.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
All __napi_complete() callers have been converted to
use the more standard napi_complete_done(),
we can now remove this NAPI method for good.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We plan to remove __napi_complete() soon,
this driver is the last user.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use napi_complete_done() instead of __napi_complete()
We plan to remove __napi_complete() to reduce NAPI complexity.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
Note that rx_lock seems to be useless, NAPI logic should
not need this extra care.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API and get rid of napi_gro_flush()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
4) get rid of baroque code and ease maintenance.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
4) get rid of baroque code and ease maintenance.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
4) get rid of baroque code and ease maintenance.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
4) Eventually get rid of napi_gro_flush() in the future.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ip6_print_replace_route_err logs an error if a route replace fails with
IPv6 addresses in the full format. e.g,:
IPv6: IPV6: multipath route replace failed (check consistency of installed routes): 2001:0db8:0200:0000:0000:0000:0000:0000 nexthop 2001:0db8:0001:0000:0000:0000:0000:0016 ifi 0
Change the message to dump the addresses in the compressed format.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If an entire multipath route is deleted using prefix and len (without any
nexthops), send a single RTM_DELROUTE notification with the full route
using RTA_MULTIPATH. This is done by generating the skb before the route
delete when all of the sibling routes are still present but sending it
after the route has been removed from the FIB. The skip_notify flag
is used to tell the lower fib code not to send notifications for the
individual nexthop routes.
If a route is deleted using RTA_MULTIPATH for any nexthops or a single
nexthop entry is deleted, then the nexthops are deleted one at a time with
notifications sent as each hop is deleted. This is necessary given that
IPv6 allows individual hops within a route to be deleted.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change ip6_route_multipath_add to send one notifciation with the full
route encoded with RTA_MULTIPATH instead of a series of individual routes.
This is done by adding a skip_notify flag to the nl_info struct. The
flag is used to skip sending of the notification in the fib code that
actually inserts the route. Once the full route has been added, a
notification is generated with all nexthops.
ip6_route_multipath_add handles 3 use cases: new routes, route replace,
and route append. The multipath notification generated needs to be
consistent with the order of the nexthops and it should be consistent
with the order in a FIB dump which means the route with the first nexthop
needs to be used as the route reference. For the first 2 cases (new and
replace), a reference to the route used to send the notification is
obtained by saving the first route added. For the append case, the last
route added is used to loop back to its first sibling route which is
the first nexthop in the multipath route.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPv6 returns multipath routes as a series of individual routes making
their display and handling by userspace different and more complicated
than IPv4, putting the burden on the user to see that a route is part of
a multipath route and internally creating a multipath route if desired
(e.g., libnl does this as of commit 29b71371e764). This patch addresses
this difference, allowing multipath routes to be returned using the
RTA_MULTIPATH attribute.
The end result is that IPv6 multipath routes can be treated and displayed
in a format similar to IPv4:
$ ip -6 ro ls vrf red
2001:db8:1::/120 dev eth1 proto kernel metric 256 pref medium
2001:db8:2::/120 dev eth2 proto kernel metric 256 pref medium
2001:db8:200::/120 metric 1024
nexthop via 2001:db8:1::2 dev eth1 weight 1
nexthop via 2001:db8:2::2 dev eth2 weight 1
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPv4 allows multipath routes to be deleted using just the prefix and
length. For example:
$ ip ro ls vrf red
unreachable default metric 8192
1.1.1.0/24
nexthop via 10.100.1.254 dev eth1 weight 1
nexthop via 10.11.200.2 dev eth11.200 weight 1
10.11.200.0/24 dev eth11.200 proto kernel scope link src 10.11.200.3
10.100.1.0/24 dev eth1 proto kernel scope link src 10.100.1.3
$ ip ro del 1.1.1.0/24 vrf red
$ ip ro ls vrf red
unreachable default metric 8192
10.11.200.0/24 dev eth11.200 proto kernel scope link src 10.11.200.3
10.100.1.0/24 dev eth1 proto kernel scope link src 10.100.1.3
The same notation does not work with IPv6 because of how multipath routes
are implemented for IPv6. For IPv6 only the first nexthop of a multipath
route is deleted if the request contains only a prefix and length. This
leads to unnecessary complexity in userspace dealing with IPv6 multipath
routes.
This patch allows all nexthops to be deleted without specifying each one
in the delete request. Internally, this is done by walking the sibling
list of the route matching the specifications given (prefix, length,
metric, protocol, etc).
$ ip -6 ro ls vrf red
2001:db8:1::/120 dev eth1 proto kernel metric 256 pref medium
2001:db8:2::/120 dev eth2 proto kernel metric 256 pref medium
2001:db8:200::/120 via 2001:db8:1::2 dev eth1 metric 1024 pref medium
2001:db8:200::/120 via 2001:db8:2::2 dev eth2 metric 1024 pref medium
...
$ ip -6 ro del vrf red 2001:db8:200::/120
$ ip -6 ro ls vrf red
2001:db8:1::/120 dev eth1 proto kernel metric 256 pref medium
2001:db8:2::/120 dev eth2 proto kernel metric 256 pref medium
...
Because IPv6 allows individual nexthops to be deleted without deleting
the entire route, the ip6_route_multipath_del and non-multipath code
path (ip6_route_del) have to be discriminated so that all nexthops are
only deleted for the latter case. This is done by making the existing
fc_type in fib6_config a u16 and then adding a new u16 field with
fc_delete_all_nh as the first bit.
Suggested-by: Dinesh Dutt <ddutt@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 364b6055738b ("net: busy-poll: return busypolling status to
drivers"), napi_complete_done() returns a boolean that can be used
by drivers to conditionally rearm interrupts.
This patch changes virtio_net to use this boolean to avoid a bit of
overhead for busy-poll users.
Jason reports about 1.1% improvement for 1 byte TCP_RR (burst 100).
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
My recent change missed fact that UFO would perform a complete
UDP checksum before segmenting in frags.
In this case skb->ip_summed is set to CHECKSUM_NONE.
We need to add this valid case to skb_needs_check()
Fixes: b2504a5dbef3 ("net: reduce skb_warn_bad_offload() noise")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We added generic support for busy polling in NAPI layer in linux-4.5
No network driver uses ndo_busy_poll() anymore, we can get rid
of the pointer in struct net_device_ops, and its use in sk_busy_loop()
Saves NETIF_F_BUSY_POLL features bit.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We do polling generically these days.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In linux-4.5, busy polling was implemented in core
NAPI stack, meaning that all custom implementation can
be removed from drivers.
Not only we remove lot's of code, we also remove one lock
operation in fast path, and allow GRO to do its job.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In linux-4.5, busy polling was implemented in core
NAPI stack, meaning that all custom implementation can
be removed from drivers.
Not only we remove lot's of code, we also remove one lock
operation in fast path, and allow GRO to do its job.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extend the existing setup_tc ndo call and allow to offload cls_flower
rules. Only limited set of dissector keys and actions are supported now.
Use previously introduced ACL infrastructure to offload cls_flower rules
to be processed in the HW.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver that offloads flower rules needs to know with which priority
user inserted the rules. So add this information into offload struct.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add ACL core infrastructure for Spectrum ASIC. This infra provides an
abstraction layer over specific HW implementations. There are two basic
objects used. One is "rule" and the second is "ruleset" which serves as a
container of multiple rules. In general, within one ruleset the rules are
allowed to have multiple priorities and masks. Each ruleset is bound to
either ingress or egress a of port netdevice.
The initial TCAM implementation is very simple and limited. It utilizes
parman lsort manager to take care of TCAM region layout.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This introduces a infrastructure for management of linear priority
areas. Priority order in an array matters, however order of items inside
a priority group does not matter.
As an initial implementation, L-sort algorithm is used. It is quite
trivial. More advanced algorithm called P-sort will be introduced as a
follow-up. The infrastructure is prepared for other algos.
Alongside this, a testing module is introduced as well.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similar to list_for_each_entry_continue and its reverse variant
list_for_each_entry_continue_reverse, introduce reverse helper for
list_for_each_entry_from.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|