aboutsummaryrefslogtreecommitdiffstats
path: root/net/batman-adv (follow)
AgeCommit message (Collapse)AuthorFilesLines
2016-11-08batman-adv: additional checks for virtual interfaces on top of WiFiMarek Lindner2-0/+62
In a few situations batman-adv tries to determine whether a given interface is a WiFi interface to enable specific WiFi optimizations. If the interface batman-adv has been configured with is a virtual interface (e.g. VLAN) it would not be properly detected as WiFi interface and thus not benefit from the special WiFi treatment. This patch changes that by peeking under the hood whenever a virtual interface is in play. Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> [sven.eckelmann@open-mesh.com: integrate in wifi_flags caching, retrieve namespace of link interface] Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2016-11-08batman-adv: Cache the type of wifi device for each hardifSven Eckelmann6-25/+95
batman-adv is requiring the type of wifi device in different contexts. Some of them can take the rtnl semaphore and some of them already have the semaphore taken. But even others don't allow that the semaphore will be taken. The data has to be retrieved when the hardif is added to batman-adv because some of the wifi information for an hardif will only be available with rtnl lock. It can then be cached in the batadv_hard_iface and the functions is_wifi_netdev and is_cfg80211_netdev can just compare the correct bits without imposing extra locking requirements. Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2016-11-08batman-adv: refactor wifi interface detectionMarek Lindner3-20/+36
The ELP protocol requires cfg80211 to auto-detect the WiFi througput to a given neighbor. Use batadv_is_cfg80211_netdev() to determine whether or not an interface is eligible. Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2016-11-08batman-adv: Reject unicast packet with zero/mcast dst addressSven Eckelmann1-4/+4
An unicast batman-adv packet cannot be transmitted to a multicast or zero mac address. So reject incoming packets which still have these classes of addresses as destination mac address in the outer ethernet header. Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2016-11-08batman-adv: Return non-const ptr in batadv_getlink_netSven Eckelmann1-5/+5
The returned net_namespace of batadv_getlink_net may be used with functions that potentially modify the struct. Thus it must return the pointer as non-const like rtnl_link_ops::get_link_net does. Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2016-11-08batman-adv: Disallow zero and mcast src address for mgmt framesSven Eckelmann1-2/+2
The routing check for management frames is validating the source mac address in the outer ethernet header. It rejects every source mac address which is a broadcast address. But it also has to reject the zero-mac address and multicast mac addresses. Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2016-11-08batman-adv: Disallow mcast src address for data framesSven Eckelmann1-6/+6
The routing checks are validating the source mac address of the outer ethernet header. They reject every source mac address which is a broadcast address. But they also have to reject any multicast mac addresses. Signed-off-by: Sven Eckelmann <sven@narfation.org> [sw@simonwunderlich.de: fix commit message typo] Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2016-11-08batman-adv: Remove dev_queue_xmit return code exceptionSven Eckelmann1-11/+6
No caller of batadv_send_skb_to_orig is expecting the results to be -1 (-EPERM) anymore when the skbuff was not consumed. They will instead expect that the skbuff is always consumed. Having such return code filter is therefore not needed anymore. Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2016-11-08batman-adv: Consume skb in receive handlersSven Eckelmann6-85/+153
Receiving functions in Linux consume the supplied skbuff. Doing the same in the batadv_rx_handler functions makes the behavior more similar to the rest of the Linux network code. Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2016-11-04batman-adv: Detect missing primaryif during tp_send as errorSven Eckelmann1-0/+1
The throughput meter detects different situations as problems for the current test. It stops the test after these and reports it to userspace. This also has to be done when the primary interface disappeared during the test. Fixes: 33a3bb4a3345 ("batman-adv: throughput meter implementation") Reported-by: Joe Perches <joe@perches.com> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2016-11-04batman-adv: Revert "fix splat on disabling an interface"Sven Eckelmann1-0/+1
The commit 9799c50372b2 ("batman-adv: fix splat on disabling an interface") fixed a warning but at the same time broke the rtnl function add_slave for devices which were temporarily removed. batadv_softif_slave_add requires soft_iface of and hard_iface to be NULL before it is allowed to be enslaved. But this resetting of soft_iface to NULL in batadv_hardif_disable_interface was removed with the aforementioned commit. Reported-by: Julian Labus <julian@freifunk-rtk.de> Signed-off-by: Sven Eckelmann <sven@narfation.org> Acked-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2016-10-30Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller3-3/+2
Mostly simple overlapping changes. For example, David Ahern's adjacency list revamp in 'net-next' conflicted with an adjacency list traversal bug fix in 'net'. Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-30batman-adv: Consume skb in batadv_send_skb_to_origSven Eckelmann4-36/+25
Sending functions in Linux consume the supplied skbuff. Doing the same in batadv_send_skb_to_orig avoids the hack of returning -1 (-EPERM) to signal the caller that he is responsible for cleaning up the skb. Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2016-10-30batman-adv: Consume skb in batadv_frag_send_packetSven Eckelmann1-21/+29
Sending functions in Linux consume the supplied skbuff. Doing the same in batadv_frag_send_packet avoids the hack of returning -1 (-EPERM) to signal the caller that he is responsible for cleaning up the skb. Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2016-10-30batman-adv: Count all non-success TX packets as droppedSven Eckelmann1-1/+1
A failure during the submission also causes dropped packets. batadv_interface_tx should therefore also increase the DROPPED counter for these returns. Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2016-10-30batman-adv: use consume_skb for non-dropped packetsSven Eckelmann6-30/+59
kfree_skb assumes that an skb is dropped after an failure and notes that. consume_skb should be used in non-failure situations. Such information is important for dropmonitor netlink which tells how many packets were dropped and where this drop happened. Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2016-10-30batman-adv: Simple (re)broadcast avoidanceLinus Lüssing9-8/+193
With this patch, (re)broadcasting on a specific interfaces is avoided: * No neighbor: There is no need to broadcast on an interface if there is no node behind it. * Single neighbor is source: If there is just one neighbor on an interface and if this neighbor is the one we actually got this broadcast packet from, then we do not need to echo it back. * Single neighbor is originator: If there is just one neighbor on an interface and if this neighbor is the originator of this broadcast packet, then we do not need to echo it back. Goodies for BATMAN V: ("Upgrade your BATMAN IV network to V now to get these for free!") Thanks to the split of OGMv1 into two packet types, OGMv2 and ELP that is, we can now apply the same optimizations stated above to OGMv2 packets, too. Furthermore, with BATMAN V, rebroadcasts can be reduced in certain multi interface cases, too, where BATMAN IV cannot. This is thanks to the removal of the "secondary interface originator" concept in BATMAN V. Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2016-10-30batman-adv: Use own timer for multicast TT and TVLV updatesLinus Lüssing5-17/+60
Instead of latching onto the OGM period, this patch introduces a worker dedicated to multicast TT and TVLV updates. The reasoning is, that upon roaming especially the translation table should be updated timely to minimize connectivity issues. With BATMAN V, the idea is to greatly increase the OGM interval to reduce overhead. Unfortunately, right now this could lead to a bad user experience if multicast traffic is involved. Therefore this patch introduces a fixed 500ms update interval for multicast TT entries and the multicast TVLV. Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2016-10-30batman-adv: Remove unused skb_reset_mac_header()Linus Lüssing1-2/+0
During broadcast queueing, the skb_reset_mac_header() sets the skb to a place invalid for a MAC header, pointing right into the batman-adv broadcast packet. Luckily, no one seems to actually use eth_hdr(skb) afterwards until batadv_send_skb_packet() resets the header to a valid position again. Therefore removing this unnecessary, weird skb_reset_mac_header() call. Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2016-10-30batman-adv: Remove unnecessary lockdep in batadv_mcast_mla_list_freeLinus Lüssing1-6/+2
batadv_mcast_mla_list_free() just frees some leftovers of a local feast in batadv_mcast_mla_update(). No lockdep needed as it has nothing to do with bat_priv->mcast.mla_list. Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2016-10-30batman-adv: Add wrapper for ARP reply creationLinus Lüssing1-27/+40
Removing duplicate code. Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2016-10-30batman-adv: Close two alignment holes in batadv_hard_ifaceSven Eckelmann1-2/+2
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2016-10-30batman-adv: Mark batadv_netlink_ops as constSven Eckelmann1-1/+1
The genl_ops don't need to be written by anyone and thus can be moved in a ro memory range. Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2016-10-30batman-adv: Introduce missing headers for genetlink restructureSven Eckelmann1-0/+3
Fixes: 56989f6d8568 ("genetlink: mark families as __ro_after_init") Fixes: 2ae0f17df1cd ("genetlink: use idr to track families") Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2016-10-29Merge tag 'batadv-next-for-davem-20161027' of git://git.open-mesh.org/linux-mergeDavid S. Miller23-190/+129
Simon Wunderlich says: ==================== This code cleanup patchset includes the following changes (chronological order): - bump version strings, by Simon Wunderlich - README updates/clean up, by Sven Eckelmann (4 patches) - Code clean up and restructuring by Sven Eckelmann (2 patches) - Kerneldoc fix in forw_packet structure, by Linus Luessing - Remove unused argument in dbg_arp, by Antonio Quartulli - Add support to build batman-adv without wireless, by Linus Luessing - Restructure error handling for is_ap_isolated, by Markus Elfring - Remove unused initialization in various functions, by Sven Eckelmann - Use better names for fragment and gateway list heads, by Sven Eckelmann (2 patches) - Convert to octal permissions for files, by Sven Eckelmann - Avoid precedence issues for some macros, by Sven Eckelmann ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-27genetlink: mark families as __ro_after_initJohannes Berg1-1/+1
Now genl_register_family() is the only thing (other than the users themselves, perhaps, but I didn't find any doing that) writing to the family struct. In all families that I found, genl_register_family() is only called from __init functions (some indirectly, in which case I've add __init annotations to clarifly things), so all can actually be marked __ro_after_init. This protects the data structure from accidental corruption. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-27genetlink: statically initialize familiesJohannes Berg1-10/+15
Instead of providing macros/inline functions to initialize the families, make all users initialize them statically and get rid of the macros. This reduces the kernel code size by about 1.6k on x86-64 (with allyesconfig). Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-27genetlink: no longer support using static family IDsJohannes Berg1-1/+0
Static family IDs have never really been used, the only use case was the workaround I introduced for those users that assumed their family ID was also their multicast group ID. Additionally, because static family IDs would never be reserved by the generic netlink code, using a relatively low ID would only work for built-in families that can be registered immediately after generic netlink is started, which is basically only the control family (apart from the workaround code, which I also had to add code for so it would reserve those IDs) Thus, anything other than GENL_ID_GENERATE is flawed and luckily not used except in the cases I mentioned. Move those workarounds into a few lines of code, and then get rid of GENL_ID_GENERATE entirely, making it more robust. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-26batman-adv: Revert "use core MTU range checking in misc drivers"Sven Eckelmann1-1/+12
The maximum MTU is defined via the slave devices of an batman-adv interface. Thus it is not possible to calculate the max_mtu during the creation of the batman-adv device when no slave devices are attached. Doing so would for example break non-fragmentation setups which then (incorrectly) allow an MTU of 1500 even when underlying device cannot transport 1500 bytes + batman-adv headers. Checking the dynamically calculated max_mtu via the minimum of the slave devices MTU during .ndo_change_mtu is also used by the bridge interface. Cc: Jarod Wilson <jarod@redhat.com> Fixes: b3e3893e1253 ("net: use core MTU range checking in misc drivers") Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-21batman-adv: fix splat on disabling an interfaceLinus Lüssing1-1/+0
As long as there is still a reference for a hard interface held, there might still be a forwarding packet relying on its attributes. Therefore avoid setting hard_iface->soft_iface to NULL when disabling a hard interface. This fixes the following, potential splat: batman_adv: bat0: Interface deactivated: eth1 batman_adv: bat0: Removing interface: eth1 cgroup: new mount options do not match the existing superblock, will be ignored batman_adv: bat0: Interface deactivated: eth3 batman_adv: bat0: Removing interface: eth3 ------------[ cut here ]------------ WARNING: CPU: 3 PID: 1986 at ./net/batman-adv/bat_iv_ogm.c:549 batadv_iv_send_outstanding_bat_ogm_packet+0x145/0x643 [batman_adv] Modules linked in: batman_adv(O-) <...> CPU: 3 PID: 1986 Comm: kworker/u8:2 Tainted: G W O 4.6.0-rc6+ #1 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140531_083030-gandalf 04/01/2014 Workqueue: bat_events batadv_iv_send_outstanding_bat_ogm_packet [batman_adv] 0000000000000000 ffff88001d93bca0 ffffffff8126c26b 0000000000000000 0000000000000000 ffff88001d93bcf0 ffffffff81051615 ffff88001f19f818 000002251d93bd68 0000000000000046 ffff88001dc04a00 ffff88001becbe48 Call Trace: [<ffffffff8126c26b>] dump_stack+0x67/0x90 [<ffffffff81051615>] __warn+0xc7/0xe5 [<ffffffff8105164b>] warn_slowpath_null+0x18/0x1a [<ffffffffa0356f24>] batadv_iv_send_outstanding_bat_ogm_packet+0x145/0x643 [batman_adv] [<ffffffff8108b01f>] ? __lock_is_held+0x32/0x54 [<ffffffff810689a2>] process_one_work+0x2a8/0x4f5 [<ffffffff81068856>] ? process_one_work+0x15c/0x4f5 [<ffffffff81068df2>] worker_thread+0x1d5/0x2c0 [<ffffffff81068c1d>] ? process_scheduled_works+0x2e/0x2e [<ffffffff81068c1d>] ? process_scheduled_works+0x2e/0x2e [<ffffffff8106dd90>] kthread+0xc0/0xc8 [<ffffffff8144de82>] ret_from_fork+0x22/0x40 [<ffffffff8106dcd0>] ? __init_kthread_worker+0x55/0x55 ---[ end trace 647f9f325123dc05 ]--- What happened here is, that there was still a forw_packet (here: a BATMAN IV OGM) in the queue of eth3 with the forw_packet->if_incoming set to eth1 and the forw_packet->if_outgoing set to eth3. When eth3 is to be deactivated and removed, then this thread waits for the forw_packet queued on eth3 to finish. Because eth1 was deactivated and removed earlier and by that had forw_packet->if_incoming->soft_iface, set to NULL, the splat when trying to send/flush the OGM on eth3 occures. Fixes: c6c8fea29769 ("net: Add batman-adv meshing protocol") Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> [sven@narfation.org: Reduced size of Oops message] Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2016-10-20net: use core MTU range checking in misc driversJarod Wilson1-12/+1
firewire-net: - set min/max_mtu - remove fwnet_change_mtu nes: - set max_mtu - clean up nes_netdev_change_mtu xpnet: - set min/max_mtu - remove xpnet_dev_change_mtu hippi: - set min/max_mtu - remove hippi_change_mtu batman-adv: - set max_mtu - remove batadv_interface_change_mtu - initialization is a little async, not 100% certain that max_mtu is set in the optimal place, don't have hardware to test with rionet: - set min/max_mtu - remove rionet_change_mtu slip: - set min/max_mtu - streamline sl_change_mtu um/net_kern: - remove pointless ndo_change_mtu hsi/clients/ssi_protocol: - use core MTU range checking - remove now redundant ssip_pn_set_mtu ipoib: - set a default max MTU value - Note: ipoib's actual max MTU can vary, depending on if the device is in connected mode or not, so we'll just set the max_mtu value to the max possible, and let the ndo_change_mtu function continue to validate any new MTU change requests with checks for CM or not. Note that ipoib has no min_mtu set, and thus, the network core's mtu > 0 check is the only lower bounds here. mptlan: - use net core MTU range checking - remove now redundant mpt_lan_change_mtu fddi: - min_mtu = 21, max_mtu = 4470 - remove now redundant fddi_change_mtu (including export) fjes: - min_mtu = 8192, max_mtu = 65536 - The max_mtu value is actually one over IP_MAX_MTU here, but the idea is to get past the core net MTU range checks so fjes_change_mtu can validate a new MTU against what it supports (see fjes_support_mtu in fjes_hw.c) hsr: - min_mtu = 0 (calls ether_setup, max_mtu is 1500) f_phonet: - min_mtu = 6, max_mtu = 65541 u_ether: - min_mtu = 14, max_mtu = 15412 phonet/pep-gprs: - min_mtu = 576, max_mtu = 65530 - remove redundant gprs_set_mtu CC: netdev@vger.kernel.org CC: linux-rdma@vger.kernel.org CC: Stefan Richter <stefanr@s5r6.in-berlin.de> CC: Faisal Latif <faisal.latif@intel.com> CC: linux-rdma@vger.kernel.org CC: Cliff Whickman <cpw@sgi.com> CC: Robin Holt <robinmholt@gmail.com> CC: Jes Sorensen <jes@trained-monkey.org> CC: Marek Lindner <mareklindner@neomailbox.ch> CC: Simon Wunderlich <sw@simonwunderlich.de> CC: Antonio Quartulli <a@unstable.cc> CC: Sathya Prakash <sathya.prakash@broadcom.com> CC: Chaitra P B <chaitra.basappa@broadcom.com> CC: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com> CC: MPT-FusionLinux.pdl@broadcom.com CC: Sebastian Reichel <sre@kernel.org> CC: Felipe Balbi <balbi@kernel.org> CC: Arvid Brodin <arvid.brodin@alten.se> CC: Remi Denis-Courmont <courmisch@gmail.com> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-19batman-adv: Avoid precedence issues in macrosSven Eckelmann3-9/+9
It must be avoided that arguments to a macro are evaluated ungrouped (which enforces normal operator precendence). Otherwise the result of the macro is not well defined. Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2016-10-19batman-adv: Use octal permissions instead of macrosSven Eckelmann5-55/+41
Linus prefers to have octal permission numbers instead of combinations of macro names ("random line noise"). Also old existing "bad symbolic permission bit macro use" should be converted to octal numbers. (http://lkml.kernel.org/r/CA+55aFw5v23T-zvDZp-MmD_EYxF8WbafwwB59934FV7g21uMGQ@mail.gmail.com) Also remove the S_IFREG bit from the octal representation because it is filtered out by debugfs_create. Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2016-10-19batman-adv: Use proper name for gateway list headSven Eckelmann5-14/+15
The batman-adv codebase is using "list" for the list node (prev/next) and <list content descriptor>+"_list" for the head of a list. Not using this naming scheme can up in confusions when reading the code. Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2016-10-19batman-adv: Use proper name for fragments list headSven Eckelmann4-12/+12
The batman-adv codebase is using "list" for the list node (prev/next) and <list content descriptor>+"_list" for the head of a list. Not using this naming scheme can up in confusions because list_head is used for both the head of the list and the list node (prev/next) in each item of the list. Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2016-10-19batman-adv: Remove needless init of variables on stackSven Eckelmann6-11/+11
Some variables are overwritten immediatelly in a functions. These don't have to be initialized to a specific value on the stack because the value will be overwritten before they will be used anywhere. Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2016-10-18batman-adv: Less function calls in batadv_is_ap_isolated() after error detectionMarkus Elfring1-14/+11
The variables "tt_local_entry" and "tt_global_entry" were eventually checked again despite of a corresponding null pointer test before. * Avoid this double check by reordering a function call sequence and the better selection of jump targets. * Omit the initialisation for these variables at the beginning then. Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2016-10-17batman-adv: Allow selecting BATMAN V if CFG80211 is not builtLinus Lüssing1-1/+1
With the new stub for cfg80211_get_station(), we can now build the BATMAN V protocol even with a kernel that was built without any wireless support. Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2016-10-17batman-adv: remove unsed argument from batadv_dbg_arp() functionAntonio Quartulli1-11/+6
The argument "type" passed to the batadv_dbg_arp() function is never used. Remove it. Signed-off-by: Antonio Quartulli <a@unstable.cc> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2016-10-17batman-adv: fix batadv_forw_packet kerneldoc for list attributeLinus Lüssing1-1/+1
The forw_packet list node is wrongly attributed to the icmp socket code. Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2016-10-17batman-adv: Remove unused batadv_icmp_user_cmd_typeSven Eckelmann1-10/+0
Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2016-10-17batman-adv: Move batadv_sum_counter to soft-interface.cSven Eckelmann2-21/+21
The function batadv_sum_counter is only used in soft-interface.c and has no special relevance for main.h. Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2016-10-17batman-adv: Remove unused function batadv_hash_deleteSven Eckelmann1-30/+0
Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2016-10-17batman-adv: Add BATADV_DBG_TP_METER to BATADV_DBG_ALLSven Eckelmann1-1/+1
The BATADV_DBG_ALL has to contain the bit of BATADV_DBG_TP_METER to really support all available debug messages. Fixes: 33a3bb4a3345 ("batman-adv: throughput meter implementation") Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2016-10-17batman-adv: Modify neigh_list only with rcu-list functionsSven Eckelmann1-1/+1
The batadv_hard_iface::neigh_list is accessed via rcu based primitives. Thus all operations done on it have to fulfill the requirements by RCU. So using non-RCU mechanisms like hlist_add_head is not allowed because it misses the barriers required to protect concurrent readers when accessing the data behind the pointer. Fixes: cef63419f7db ("batman-adv: add list of unique single hop neighbors per hard-interface") Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> Acked-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2016-10-17batman-adv: Start new development cycleSimon Wunderlich1-1/+1
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2016-10-11treewide: remove redundant #include <linux/kconfig.h>Masahiro Yamada1-2/+0
Kernel source files need not include <linux/kconfig.h> explicitly because the top Makefile forces to include it with: -include $(srctree)/include/linux/kconfig.h This commit removes explicit includes except the following: * arch/s390/include/asm/facilities_src.h * tools/testing/radix-tree/linux/kernel.h These two are used for host programs. Link: http://lkml.kernel.org/r/1473656164-11929-1-git-send-email-yamada.masahiro@socionext.com Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-09-23Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2-2/+28
2016-09-01batman: make netlink attributes conststephen hemminger1-2/+2
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-08-26batman-adv: fix elp packet data reservationLinus Lüssing1-1/+1
The skb_reserve() call only reserved headroom for the mac header, but not the elp packet header itself. Fixing this by using skb_put()'ing towards the skb tail instead of skb_push()'ing towards the skb head. Fixes: d6f94d91f766 ("batman-adv: ELP - adding basic infrastructure") Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.