aboutsummaryrefslogtreecommitdiffstats
path: root/net/caif (unfollow)
AgeCommit message (Collapse)AuthorFilesLines
2014-07-15net: set name assign type for renamed devicesTom Gundersen1-0/+7
Based on a patch from David Herrmann. This is the only place devices can be renamed. v9: restore revers-christmas-tree order of local variables Signed-off-by: Tom Gundersen <teg@jklm.no> Reviewed-by: David Herrmann <dh.herrmann@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-15net: add name_assign_type netdev attributeTom Gundersen4-0/+39
Based on a patch by David Herrmann. The name_assign_type attribute gives hints where the interface name of a given net-device comes from. These values are currently defined: NET_NAME_ENUM: The ifname is provided by the kernel with an enumerated suffix, typically based on order of discovery. Names may be reused and unpredictable. NET_NAME_PREDICTABLE: The ifname has been assigned by the kernel in a predictable way that is guaranteed to avoid reuse and always be the same for a given device. Examples include statically created devices like the loopback device and names deduced from hardware properties (including being given explicitly by the firmware). Names depending on the order of discovery, or in any other way on the existence of other devices, must not be marked as PREDICTABLE. NET_NAME_USER: The ifname was provided by user-space during net-device setup. NET_NAME_RENAMED: The net-device has been renamed from userspace. Once this type is set, it cannot change again. NET_NAME_UNKNOWN: This is an internal placeholder to indicate that we yet haven't yet categorized the name. It will not be exposed to userspace, rather -EINVAL is returned. The aim of these patches is to improve user-space renaming of interfaces. As a general rule, userspace must rename interfaces to guarantee that names stay the same every time a given piece of hardware appears (at boot, or when attaching it). However, there are several situations where userspace should not perform the renaming, and that depends on both the policy of the local admin, but crucially also on the nature of the current interface name. If an interface was created in repsonse to a userspace request, and userspace already provided a name, we most probably want to leave that name alone. The main instance of this is wifi-P2P devices created over nl80211, which currently have a long-standing bug where they are getting renamed by udev. We label such names NET_NAME_USER. If an interface, unbeknown to us, has already been renamed from userspace, we most probably want to leave also that alone. This will typically happen when third-party plugins (for instance to udev, but the interface is generic so could be from anywhere) renames the interface without informing udev about it. A typical situation is when you switch root from an installer or an initrd to the real system and the new instance of udev does not know what happened before the switch. These types of problems have caused repeated issues in the past. To solve this, once an interface has been renamed, its name is labelled NET_NAME_RENAMED. In many cases, the kernel is actually able to name interfaces in such a way that there is no need for userspace to rename them. This is the case when the enumeration order of devices, or in fact any other (non-parent) device on the system, can not influence the name of the interface. Examples include statically created devices, or any naming schemes based on hardware properties of the interface. In this case the admin may prefer to use the kernel-provided names, and to make that possible we label such names NET_NAME_PREDICTABLE. We want the kernel to have tho possibilty of performing predictable interface naming itself (and exposing to userspace that it has), as the information necessary for a proper naming scheme for a certain class of devices may not be exposed to userspace. The case where renaming is almost certainly desired, is when the kernel has given the interface a name using global device enumeration based on order of discovery (ethX, wlanY, etc). These naming schemes are labelled NET_NAME_ENUM. Lastly, a fallback is left as NET_NAME_UNKNOWN, to indicate that a driver has not yet been ported. This is mostly useful as a transitionary measure, allowing us to label the various naming schemes bit by bit. v8: minor documentation fixes v9: move comment to the right commit Signed-off-by: Tom Gundersen <teg@jklm.no> Reviewed-by: David Herrmann <dh.herrmann@gmail.com> Reviewed-by: Kay Sievers <kay@vrfy.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-15net: mvpp2: Fix a typo in the licenseEzequiel Garcia1-1/+1
The proper string for this license is "GPL v2", instead of "GPLv2". This commit fixes that. Reported-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-14ethernet: amd: fix 'foo* bar'Varka Bhadram1-36/+40
This patch fix the 'foo*' bar with 'foo *bar' and (foo*) with (foo *). Signed-off-by: Varka Bhadram <varkab@cdac.in> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-14ethernet: amd: fix pci device idsVarka Bhadram1-9/+11
Normally any device ids will be above the corresponding device driver structure. This patch moves the pci device ids and MODULE_DEVICE_TABLE() above the pci driver structure. Signed-off-by: Varka Bhadram <varkab@cdac.in> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-14ethernet: amd: fix comment stylesVarka Bhadram1-95/+86
This patch fixes the comment style issues Signed-off-by: Varka Bhadram <varkab@cdac.in> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-14ethernet: amd: dynamic debug fixesVarka Bhadram1-32/+26
This patch convert printk() to netdev_dbg/info/err or dev_info/err/dbg Signed-off-by: Varka Bhadram <varkab@cdac.in> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-14ethernet: amd: use devm_ioremap()Varka Bhadram1-5/+2
This patch replace ioremap() with the devm_ioremap() so that the resource will be freed automatically with the probe failed. Signed-off-by: Varka Bhadram <varkab@cdac.in> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-14ethernet: amd: move amd111e_remove_one after probeVarka Bhadram1-12/+13
This patch moves the remove functionalities after the probe so that we can see the registered and released resources properly. Every driver follows the same concept. Signed-off-by: Varka Bhadram <varkab@cdac.in> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-14sfc: Add 40G link capability decodingEdward Cree1-0/+11
Needed to select 40G mode on a 10G/40G capable card. Signed-off-by: Shradha Shah <sshah@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-14sfc: Adding PCI ID for Solarflare 7000 series 40G network adapter.Mateusz Wrzesinski1-0/+2
Signed-off-by: Shradha Shah <sshah@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-14udp: Move udp_tunnel_segment into udp_offload.cTom Herbert2-76/+76
Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-14l2tp: Call udp_sock_createTom Herbert2-59/+28
In l2tp driver call common function udp_sock_create to create the listener UDP port. Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-14vxlan: Call udp_sock_createTom Herbert2-91/+25
In vxlan driver call common function udp_sock_create to create the listener UDP port. Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-14udp: Add udp_sock_create for UDP tunnels to open listener socketTom Herbert4-0/+137
Added udp_tunnel.c which can contain some common functions for UDP tunnels. The first function in this is udp_sock_create which is used to open the listener port for a UDP tunnel. Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-13slip: remove unnecessary break after gotoFabian Frederick1-1/+0
Signed-off-by: Fabian Frederick <fabf@skynet.be> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-13rtlwifi: remove unnecessary break after gotoFabian Frederick1-1/+0
Signed-off-by: Fabian Frederick <fabf@skynet.be> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-13wcn36xx: remove unnecessary break after gotoFabian Frederick1-1/+0
Signed-off-by: Fabian Frederick <fabf@skynet.be> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-13orinoco_usb: remove unnecessary break after gotoFabian Frederick1-1/+0
Signed-off-by: Fabian Frederick <fabf@skynet.be> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-13ps3_gelic: remove unnecessary break after gotoFabian Frederick1-3/+0
Signed-off-by: Fabian Frederick <fabf@skynet.be> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-13i40evf: remove unnecessary break after gotoFabian Frederick1-2/+0
Signed-off-by: Fabian Frederick <fabf@skynet.be> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-13i40e: remove unnecessary break after gotoFabian Frederick1-2/+0
Signed-off-by: Fabian Frederick <fabf@skynet.be> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-13ixgbe: remove unnecessary break after gotoFabian Frederick3-7/+0
Signed-off-by: Fabian Frederick <fabf@skynet.be> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-13igb: remove unnecessary break after gotoFabian Frederick1-1/+0
Signed-off-by: Fabian Frederick <fabf@skynet.be> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-13net: filter: sk_chk_filter() no longer mangles filterEric Dumazet2-4/+4
Add const attribute to filter argument to make clear it is no longer modified. Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Daniel Borkmann <dborkman@redhat.com> Acked-by: Alexei Starovoitov <ast@plumgrid.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-11ipv6: Use BUG_ONHimangi Saraogi1-2/+2
The semantic patch that makes this transformation is as follows: // <smpl> @@ expression e; @@ -if (e) BUG(); +BUG_ON(e); // </smpl> Signed-off-by: Himangi Saraogi <himangi774@gmail.com> Acked-by: Julia Lawall <julia.lawall@lip6.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-11net: ipv6: Use BUG_ONHimangi Saraogi1-4/+2
The semantic patch that makes the transformation is as follows: // <smpl> @@ expression e; @@ -if (e) BUG(); +BUG_ON(e); // </smpl> Signed-off-by: Himangi Saraogi <himangi774@gmail.com> Acked-by: Julia Lawall <julia.lawall@lip6.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-11ipv6: addrconf: implement address generation modesJiri Pirko3-18/+45
This patch introduces a possibility for userspace to set various (so far two) modes of generating addresses. This is useful for example for NetworkManager because it can set the mode to NONE and take care of link local addresses itself. That allow it to have the interface up, monitoring carrier but still don't have any addresses on it. One more use-case by Dan Williams: <quote> WWAN devices often have their LL address provided by the firmware of the device, which sometimes refuses to respond to incorrect LL addresses when doing DHCPv6 or IPv6 ND. The kernel cannot generate the correct LL address for two reasons: 1) WWAN pseudo-ethernet interfaces often construct a fake MAC address, or read a meaningless MAC address from the firmware. Thus the EUI64 and the IPv6LL address the kernel assigns will be wrong. The real LL address is often retrieved from the firmware with AT or proprietary commands. 2) WWAN PPP interfaces receive their LL address from IPV6CP, not from kernel assignments. Only after IPV6CP has completed do we know the LL address of the PPP interface and its peer. But the kernel has already assigned an incorrect LL address to the interface. So being able to suppress the kernel LL address generation and assign the one retrieved from the firmware is less complicated and more robust. </quote> Signed-off-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-11net/hsr: Remove left-over never-true conditional code.Arvid Brodin1-4/+0
MacAddressB is an array (unsigned char MacAddressB[ETH_ALEN]) and is allocated as a part of *node_dst (which is a struct hsr_node). So the condition is always false. Detected by Dan Carpenter. Signed-off-by: Arvid Brodin <arvid.brodin@alten.se> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-11r8169: support IPv6hayeswang1-12/+145
Support the IPv6 hw checksum for RTL8111C and later chips. Note that the hw has the limitation for the transport offset. The checksum must be calculated by sw, when the transport offset is out of the range which the hw accepts. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-11r8169: use Giant Sendhayeswang1-1/+7
Replace large send with giant send for TSO for RTL8111C and later ICs. The large send setting of the RTL8111DP is different from the other chips. However, the giant send setting is the same for all the chips which support it. Use the giant send to synchronize the settings. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-11r8169: split rtl8169_tso_csumhayeswang1-34/+37
According to the txd_version, split rtl8169_tso_csum() into rtl8169_tso_csum_v1() and rtl8169_tso_csum_v2(). Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-11ipv4: remove the unnecessary variable in udp_mcast_nextLi RongQing1-5/+4
Signed-off-by: Li RongQing <roy.qing.li@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-11dp83640: Adjust ptp event timestampsStefan Sørensen1-0/+3
Event timestamp values should be adjusted by 3*reference clock period + 11 ns = 35 ns to compensate for input path and synchronization delays. So subtract 35ns from event timestamps. Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-10ethernet: Add new driver for Marvell Armada 375 network unitMarcin Wojtas4-0/+6463
This commit adds a new network driver for the network controller in Marvell Armada 375 SoC. Given the controller is very different from the ones in the other Marvell SoCs that use the mv643xx_eth (Kirkwood, Orion, Discovery) and mvneta (Armada 370/38x/XP) drivers, a new driver is needed. Signed-off-by: Marcin Wojtas <mw@semihalf.com> [Ezequiel: coding style cleanup] Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-10ipv6: fix the check when handle RALi RongQing1-6/+6
d9333196572(ipv6: Allow accepting RA from local IP addresses.) made the wrong check, whether or not to accept RA with source-addr found on local machine, when accept_ra_from_local is 0. Fixes: d9333196572(ipv6: Allow accepting RA from local IP addresses.) Cc: Ben Greear <greearb@candelatech.com> Cc: Hannes Frederic Sowa <hannes@redhat.com> Signed-off-by: Li RongQing <roy.qing.li@gmail.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-10net: cpmac: fix in debug messagesVarka Bhadram1-12/+12
This patch fix the debug message format. This patch changes to the commit f160a2d0b524eeebd97a68e2fbb59fad4cdd3fee: net: cpmac: dynamic debug fixes When we use pr_debug()/netdev_dbg() new lines are inserting in b/w the values. The format when i use the printk() These formats used in skb dump and reg dump. This functions called from the entire code. So this will be enabled all the lines. Signed-off-by: Varka Bhadram <varkab@cdac.in> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-10bridge: netlink dump interface at par with brctlJamal Hadi Salim2-19/+70
Actually better than brctl showmacs because we can filter by bridge port in the kernel. The current bridge netlink interface doesnt scale when you have many bridges each with large fdbs or even bridges with many bridge ports And now for the science non-fiction novel you have all been waiting for.. //lets see what bridge ports we have root@moja-1:/configs/may30-iprt/bridge# ./bridge link show 8: eth1 state DOWN : <BROADCAST,MULTICAST> mtu 1500 master br0 state disabled priority 32 cost 19 17: sw1-p1 state DOWN : <BROADCAST,NOARP> mtu 1500 master br0 state disabled priority 32 cost 100 // show all.. root@moja-1:/configs/may30-iprt/bridge# ./bridge fdb show 33:33:00:00:00:01 dev bond0 self permanent 33:33:00:00:00:01 dev dummy0 self permanent 33:33:00:00:00:01 dev ifb0 self permanent 33:33:00:00:00:01 dev ifb1 self permanent 33:33:00:00:00:01 dev eth0 self permanent 01:00:5e:00:00:01 dev eth0 self permanent 33:33:ff:22:01:01 dev eth0 self permanent 02:00:00:12:01:02 dev eth1 vlan 0 master br0 permanent 00:17:42:8a:b4:05 dev eth1 vlan 0 master br0 permanent 00:17:42:8a:b4:07 dev eth1 self permanent 33:33:00:00:00:01 dev eth1 self permanent 33:33:00:00:00:01 dev gretap0 self permanent da:ac:46:27:d9:53 dev sw1-p1 vlan 0 master br0 permanent 33:33:00:00:00:01 dev sw1-p1 self permanent //filter by bridge root@moja-1:/configs/may30-iprt/bridge# ./bridge fdb show br br0 02:00:00:12:01:02 dev eth1 vlan 0 master br0 permanent 00:17:42:8a:b4:05 dev eth1 vlan 0 master br0 permanent 00:17:42:8a:b4:07 dev eth1 self permanent 33:33:00:00:00:01 dev eth1 self permanent da:ac:46:27:d9:53 dev sw1-p1 vlan 0 master br0 permanent 33:33:00:00:00:01 dev sw1-p1 self permanent // bridge sw1 has no ports attached.. root@moja-1:/configs/may30-iprt/bridge# ./bridge fdb show br sw1 //filter by port root@moja-1:/configs/may30-iprt/bridge# ./bridge fdb show brport eth1 02:00:00:12:01:02 vlan 0 master br0 permanent 00:17:42:8a:b4:05 vlan 0 master br0 permanent 00:17:42:8a:b4:07 self permanent 33:33:00:00:00:01 self permanent // filter by port + bridge root@moja-1:/configs/may30-iprt/bridge# ./bridge fdb show br br0 brport sw1-p1 da:ac:46:27:d9:53 vlan 0 master br0 permanent 33:33:00:00:00:01 self permanent // for shits and giggles (as they say in New Brunswick), lets // change the mac that br0 uses // Note: a magical fdb entry with no brport is added ... root@moja-1:/configs/may30-iprt/bridge# ip link set dev br0 address 02:00:00:12:01:04 // lets see if we can see the unicorn .. root@moja-1:/configs/may30-iprt/bridge# ./bridge fdb show 33:33:00:00:00:01 dev bond0 self permanent 33:33:00:00:00:01 dev dummy0 self permanent 33:33:00:00:00:01 dev ifb0 self permanent 33:33:00:00:00:01 dev ifb1 self permanent 33:33:00:00:00:01 dev eth0 self permanent 01:00:5e:00:00:01 dev eth0 self permanent 33:33:ff:22:01:01 dev eth0 self permanent 02:00:00:12:01:02 dev eth1 vlan 0 master br0 permanent 00:17:42:8a:b4:05 dev eth1 vlan 0 master br0 permanent 00:17:42:8a:b4:07 dev eth1 self permanent 33:33:00:00:00:01 dev eth1 self permanent 33:33:00:00:00:01 dev gretap0 self permanent 02:00:00:12:01:04 dev br0 vlan 0 master br0 permanent <=== there it is da:ac:46:27:d9:53 dev sw1-p1 vlan 0 master br0 permanent 33:33:00:00:00:01 dev sw1-p1 self permanent //can we see it if we filter by bridge? root@moja-1:/configs/may30-iprt/bridge# ./bridge fdb show br br0 02:00:00:12:01:02 dev eth1 vlan 0 master br0 permanent 00:17:42:8a:b4:05 dev eth1 vlan 0 master br0 permanent 00:17:42:8a:b4:07 dev eth1 self permanent 33:33:00:00:00:01 dev eth1 self permanent 02:00:00:12:01:04 dev br0 vlan 0 master br0 permanent <=== there it is da:ac:46:27:d9:53 dev sw1-p1 vlan 0 master br0 permanent 33:33:00:00:00:01 dev sw1-p1 self permanent Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-10bridge: fdb dumping takes a filter deviceJamal Hadi Salim8-10/+24
Dumping a bridge fdb dumps every fdb entry held. With this change we are going to filter on selected bridge port. Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-10r8152: support jumbo frame for RTL8153hayeswang1-4/+32
The maximum jumbo frame size for RTL8153 is 9K bytes. Change the max rx packet size to 9K. Change the use of the shared fifo from 6K (default) to 12K for tx. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-10net: cpmac: fix in releasing resourcesVarka Bhadram1-2/+3
before registering the the net device this code freeing net device by using the label 'fail' fixed by introducing an another label 'out' Signed-off-by: Varka Bhadram <varkab@cdac.in> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-10net: cpmac: fix proper spacing before return statementVarka Bhadram1-0/+8
This patch insert proper spaces before return statement. Signed-off-by: Varka Bhadram <varkab@cdac.in> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-10net: cpmac: fix missing a blank line after declarationsVarka Bhadram1-0/+8
This patch insert a blank line after declaration Signed-off-by: Varka Bhadram <varkab@cdac.in> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-10net: cpmac: fix cpmac driver structureVarka Bhadram1-3/+5
This patch changes to style of declarattion which follows every driver Signed-off-by: Varka Bhadram <varkab@cdac.in> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-10net: cpmac: dynamic debug fixesVarka Bhadram1-74/+62
This patch does the following changes 1. convert printk(KERN_DEBUG.. to netdev_dbg() if we have net_device object or convert to dev_dbg() if we have device object. 2. convert printk(KERN_WARNING.. to netdev_warn() if we have net_device object or convert to dev_warn() if we have device object 3. convert printk() to pr_* Signed-off-by: Varka Bhadram <varkab@cdac.in> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-10net: cpmac: fix commentsVarka Bhadram1-19/+21
This patch convert the normal comments to networking subsystem style comments. Signed-off-by: Varka Bhadram <varkab@cdac.in> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-10net: cpmac: remove space in macro definationVarka Bhadram1-41/+41
This patch fix the space after '#' in macro defination Signed-off-by: Varka Bhadram <varkab@cdac.in> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-09ipconfig: Only bootp paths should reference ic_dev_xid.David S. Miller1-1/+1
It is only tested, and declared, in the bootp code. So, in ic_dynamic() guard it's setting with IPCONFIG_BOOTP. Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-09net: systemport: use kcalloc instead of kzallocFlorian Fainelli1-3/+3
checkpatch.pl flagged two uses of kzalloc() for allocating and zeroing arrays, use kcalloc() instead as recommended. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-09net: systemport: align multiple lines correctlyFlorian Fainelli1-59/+58
checkpatch.pl flagged a bunch of: "CHECK: Alignment should match open parenthesis" problems, fix all of them. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.