Age | Commit message (Collapse) | Author | Files | Lines |
|
Previously, the driver would refuse to load if it couldn't secure
enough VIs from the MC to fulfill its RSS requirements.
This was causing probe to fail on later functions in
configurations where we'd run out of VIs, such as having many
VFs.
This change allows the driver to load with fewer VIs, down to a
minimum of 2. A warning will be printed saying that RSS
requirements were not met, possibly affecting performance.
efx->max_tx_channels needs to be set to avoid going down the
failure path in efx_probe_nic() immediately in the loop after the
probe() NIC-type function.
Also, Set rc=ENOSPC when bombing out of efx_probe_nic due to lack
of VIs.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Forcing uninitialized state allows us to upgrade and reinitialize
the adapter.
FW_VERSION_T4 = 1.4.0.0
FW_VERSION_T5 = 0.0.0.0
FW_VERSION_T6 = 0.0.0.0
At this point driver supports above and greater than above version.
If FW in adapter < min FW_VERSION driver supports tries to upgrade the FW
If FW in adapter >= FW_VERSION driver supports then it follows normal path
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix typo in conntrack.c
s/CONFIG_NF_CONNTRACK_LABEL/CONFIG_NF_CONNTRACK_LABELS/
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
inetpeer caches based on address only, so duplicate IP addresses within
a namespace return the same cached entry. Enhance the ipv4 address key
to contain both the IPv4 address and VRF device index.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the inetpeer_addr_base union to inetpeer_addr and drop
inetpeer_addr_base.
Both the a6 and in6_addr overlays are not needed; drop the __be32 version
and rename in6 to a6 for consistency with ipv4. Add a new u32 array to
the union which removes the need for the typecast in the compare function
and the use of a consistent arg for both ipv4 and ipv6 addresses which
makes the compare function more readable.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tcp_metrics and inetpeer both have functions to compare inetpeer
addresses. Consolidate into 1 version.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use inetpeer set,get helpers in tcp_metrics rather than peeking into
the inetpeer_addr struct.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Refactors a common line into helper function.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The change to use a custom dst broke tcpdump captures on the VRF device:
$ tcpdump -n -i vrf10
...
05:32:29.009362 IP 10.2.1.254 > 10.2.1.2: ICMP echo request, id 21989, seq 1, length 64
05:32:29.009855 00:00:40:01:8d:36 > 45:00:00:54:d6:6f, ethertype Unknown (0x0a02), length 84:
0x0000: 0102 0a02 01fe 0000 9181 55e5 0001 bd11 ..........U.....
0x0010: da55 0000 0000 bb5d 0700 0000 0000 1011 .U.....]........
0x0020: 1213 1415 1617 1819 1a1b 1c1d 1e1f 2021 ...............!
0x0030: 2223 2425 2627 2829 2a2b 2c2d 2e2f 3031 "#$%&'()*+,-./01
0x0040: 3233 3435 3637 234567
Local packets going through the VRF device are missing an ethernet header.
Fix by adding one and then stripping it off before pushing back to the IP
stack. With this patch you get the expected dumps:
...
05:36:15.713944 IP 10.2.1.254 > 10.2.1.2: ICMP echo request, id 23795, seq 1, length 64
05:36:15.714160 IP 10.2.1.2 > 10.2.1.254: ICMP echo reply, id 23795, seq 1, length 64
...
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If an interface isn't running napi_synchronize() will hang forever.
[ 392.248403] rmmod R running task 0 359 343 0x00000000
[ 392.257671] ffff88003760fc88 ffff880037193b40 ffff880037193160 ffff88003760fc88
[ 392.267644] ffff880037610000 ffff88003760fcd8 0000000100014c22 ffffffff81f75c40
[ 392.277524] 0000000000bc7010 ffff88003760fca8 ffffffff81796927 ffffffff81f75c40
[ 392.287323] Call Trace:
[ 392.291599] [<ffffffff81796927>] schedule+0x37/0x90
[ 392.298553] [<ffffffff8179985b>] schedule_timeout+0x14b/0x280
[ 392.306421] [<ffffffff810f91b9>] ? irq_free_descs+0x69/0x80
[ 392.314006] [<ffffffff811084d0>] ? internal_add_timer+0xb0/0xb0
[ 392.322125] [<ffffffff81109d07>] msleep+0x37/0x50
[ 392.329037] [<ffffffffa00ec79a>] xennet_disconnect_backend.isra.24+0xda/0x390 [xen_netfront]
[ 392.339658] [<ffffffffa00ecadc>] xennet_remove+0x2c/0x80 [xen_netfront]
[ 392.348516] [<ffffffff81481c69>] xenbus_dev_remove+0x59/0xc0
[ 392.356257] [<ffffffff814e7217>] __device_release_driver+0x87/0x120
[ 392.364645] [<ffffffff814e7cf8>] driver_detach+0xb8/0xc0
[ 392.371989] [<ffffffff814e6e69>] bus_remove_driver+0x59/0xe0
[ 392.379883] [<ffffffff814e84f0>] driver_unregister+0x30/0x70
[ 392.387495] [<ffffffff814814b2>] xenbus_unregister_driver+0x12/0x20
[ 392.395908] [<ffffffffa00ed89b>] netif_exit+0x10/0x775 [xen_netfront]
[ 392.404877] [<ffffffff81124e08>] SyS_delete_module+0x1d8/0x230
[ 392.412804] [<ffffffff8179a8ee>] system_call_fastpath+0x12/0x71
Signed-off-by: Chas Williams <3chas3@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The range of addresses between 224.0.0.0 and 224.0.0.255 inclusive, is
reserved for the use of routing protocols and other low-level topology
discovery or maintenance protocols, such as gateway discovery and
group membership reporting. Multicast routers should not forward any
multicast datagram with destination addresses in this range,
regardless of its TTL.
Currently, IGMP reports are generated for this reserved range of
addresses even though a router will ignore this information since it
has no purpose. However, the presence of reserved group addresses in
an IGMP membership report uses up network bandwidth and can also
obscure addresses of interest when inspecting membership reports using
packet inspection or debug messages.
Although the RFCs for the various version of IGMP (e.g.RFC 3376 for
v3) do not specify that the reserved addresses be excluded from
membership reports, it should do no harm in doing so. In particular
there should be no adverse effect in any IGMP snooping functionality
since 224.0.0.x is specifically excluded as per RFC 4541 (IGMP and MLD
Snooping Switches Considerations) section 2.1.2. Data Forwarding
Rules:
2) Packets with a destination IP (DIP) address in the 224.0.0.X
range which are not IGMP must be forwarded on all ports.
IGMP reports for local multicast groups can now be optionally
inhibited by means of a system control variable (by setting the value
to zero) e.g.:
echo 0 > /proc/sys/net/ipv4/igmp_link_local_mcast_reports
To retain backwards compatibility the previous behaviour is retained
by default on system boot or reverted by setting the value back to
non-zero e.g.:
echo 1 > /proc/sys/net/ipv4/igmp_link_local_mcast_reports
Signed-off-by: Philip Downey <pdowney@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The multicast hardware counter on 8168/8111 chips is only 32 bit while the
statistics in struct rtnl_link_stats64 are 64 bit. Given that statistics
are requested on an irregular basis, an overflow of the hardware counter
can go unnoticed. To count even very large numbers of multicast packets
reliably, add a software counter and remove previously applied code to
fill the multicast field requested by @rtl8169_get_stats64 with the values
read from the rx_multicast hardware counter.
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that noqueue qdisc can be attached just like any other qdisc, no
special treatment is necessary anymore when attaching it as default
qdisc.
This change has the added benefit that 'tc qdisc show' prints noqueue
instead of nothing for devices defaulting to noqueue.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This way users can attach noqueue just like any other qdisc using tc
without having to mess with tx_queue_len first.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since alloc_netdev_mqs() sets IFF_NO_QUEUE for drivers not initializing
tx_queue_len, it is safe to assume that if tx_queue_len is zero,
dev->priv flags always contains IFF_NO_QUEUE.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Printing a warning in alloc_netdev_mqs() if tx_queue_len is zero and
IFF_NO_QUEUE not set is not appropriate since drivers may use one of the
alloc_netdev* macros instead of alloc_etherdev*, thereby not
intentionally leaving tx_queue_len uninitialized. Instead check here if
tx_queue_len is zero and set IFF_NO_QUEUE, so the value of tx_queue_len
can be ignored in net/sched_generic.c.
Fixes: 906470c ("net: warn if drivers set tx_queue_len = 0")
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The symbol '__sk_reclaim' is not present in the current tree. Apparently
'__sk_reclaim' was meant to be '__sk_mem_reclaim', so fix it with the
right symbol name for the kernel doc.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Cc: Hideo Aoki <haoki@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit f8d960524328 ("sctp: Enforce retransmission limit during shutdown")
fixed a problem with excessive retransmissions in the SHUTDOWN_PENDING by not
resetting the association overall_error_count. This allowed the association
to better enforce assoc.max_retrans limit.
However, the same issue still exists when the association is in SHUTDOWN_RECEIVED
state. In this state, HB-ACKs will continue to reset the overall_error_count
for the association would extend the lifetime of association unnecessarily.
This patch solves this by resetting the overall_error_count whenever the current
state is small then SCTP_STATE_SHUTDOWN_PENDING. As a small side-effect, we
end up also handling SCTP_STATE_SHUTDOWN_ACK_SENT and SCTP_STATE_SHUTDOWN_SENT
states, but they are not really impacted because we disable Heartbeats in those
states.
Fixes: Commit f8d960524328 ("sctp: Enforce retransmission limit during shutdown")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The uninitialized value name in mlx4_en_activate_cq was used in order
to print an error message. Fixing it by replacing it with cq->vector.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We currently manage IRQs in pool_bm which is a bit field
of MAX_MSIX bits. Thus, allocating more than MAX_MSIX
interrupts can't be managed in pool_bm.
Fixing this by capping number of requested MSIXs to
MAX_MSIX.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While looking into fixing the local entries scalability issue I noticed
that the structure is badly arranged because vlan_id would fall in a
second cache line while keeping rcu which is used only when deleting
in the first, so re-arrange the structure and push rcu to the end so we
can get 16 bytes which can be used for other fields (by pushing rcu
fully in the second 64 byte chunk). With this change all the core
necessary information when doing fdb lookups will be available in a
single cache line.
pahole before (note vlan_id):
struct net_bridge_fdb_entry {
struct hlist_node hlist; /* 0 16 */
struct net_bridge_port * dst; /* 16 8 */
struct callback_head rcu; /* 24 16 */
long unsigned int updated; /* 40 8 */
long unsigned int used; /* 48 8 */
mac_addr addr; /* 56 6 */
unsigned char is_local:1; /* 62: 7 1 */
unsigned char is_static:1; /* 62: 6 1 */
unsigned char added_by_user:1; /* 62: 5 1 */
unsigned char added_by_external_learn:1; /* 62: 4 1 */
/* XXX 4 bits hole, try to pack */
/* XXX 1 byte hole, try to pack */
/* --- cacheline 1 boundary (64 bytes) --- */
__u16 vlan_id; /* 64 2 */
/* size: 72, cachelines: 2, members: 11 */
/* sum members: 65, holes: 1, sum holes: 1 */
/* bit holes: 1, sum bit holes: 4 bits */
/* padding: 6 */
/* last cacheline: 8 bytes */
}
pahole after (note vlan_id):
struct net_bridge_fdb_entry {
struct hlist_node hlist; /* 0 16 */
struct net_bridge_port * dst; /* 16 8 */
long unsigned int updated; /* 24 8 */
long unsigned int used; /* 32 8 */
mac_addr addr; /* 40 6 */
__u16 vlan_id; /* 46 2 */
unsigned char is_local:1; /* 48: 7 1 */
unsigned char is_static:1; /* 48: 6 1 */
unsigned char added_by_user:1; /* 48: 5 1 */
unsigned char added_by_external_learn:1; /* 48: 4 1 */
/* XXX 4 bits hole, try to pack */
/* XXX 7 bytes hole, try to pack */
struct callback_head rcu; /* 56 16 */
/* --- cacheline 1 boundary (64 bytes) was 8 bytes ago --- */
/* size: 72, cachelines: 2, members: 11 */
/* sum members: 65, holes: 1, sum holes: 7 */
/* bit holes: 1, sum bit holes: 4 bits */
/* last cacheline: 8 bytes */
}
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
kbuild test robot reports that certain configurations will not
automatically pick up on the "struct rt6_info" definition, so explicitly
include the header for this structure.
Fixes: 7f8a436 "openvswitch: Add conntrack action"
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When CONFIG_OPENVSWITCH is set, and CONFIG_NETFILTER is not set, the
openvswitch IPv6 fragmentation handling cannot refer to ipv6_ops because
it isn't defined. Add a dummy version to avoid #ifdefs in source files.
Fixes: 7f8a436 "openvswitch: Add conntrack action"
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The HW-SW contract requires mailboxes passed to the firmware to be 4KB
aligned. Previously, these mailboxes were mapped using streaming DMA
routines, which do not guarantee the bus addresses to be 4KB aligned.
Under certain conditions this constraint was indeed violated and errors
were observed.
By using consistent DMA mapping routines together with a mailbox size of
4KB we are guaranteed not to violate the constraint.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When transmit fails, it is an error, not a warning.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since now information about changed upper is passed along, benefit from
that and use this info directly.
This also fixes possible issues that could happen when non-master device
is added (current code does not distinguish between master and non-master
upper device).
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Scott Feldman <sfeldma@gmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Looking at rtnl kind string is kind of ugly. So use new helpers to do
this in nicer way.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Scott Feldman <sfeldma@gmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We don't use them for years, just kill them now.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add this helper so code can easily figure out if netdev is openswitch.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add this helper so code can easily figure out if netdev is a bridge.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add info that is passed along with NETDEV_CHANGEUPPER event.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Usually an skb does not have up to MAX_SKB_FRAGS frags. So no need to
initialize the unuse part of sg. This patch initialize the sg based on
the real number it will used:
- during xmit, it could be inferred from nr_frags and can_push.
- for small receive buffer, it will also be 2.
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change simplifies Geneve Tunnel hash table management.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Reviewed-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
geneve_core module handles send and receive functionality.
This way OVS could use the Geneve API. Now with use of
tunnel meatadata mode OVS can directly use Geneve netdevice.
So there is no need for separate module for Geneve. Following
patch consolidates Geneve protocol processing in single module.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With help of tunnel metadata mode OVS can directly use
Geneve devices to implement Geneve tunnels.
This patch removes all of the OVS specific Geneve code
and make OVS use a Geneve net_device. Basic geneve vport
is still there to handle compatibility with current
userspace application.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Following patch create new tunnel flag which enable
tunnel metadata collection on given device. These devices
can be used by tunnel metadata based routing or by OVS.
Geneve Consolidation patch get rid of collect_md_tun to
simplify tunnel lookup further.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add netlink interface to configure Geneve UDP port number.
So that user can configure it for a Gevene device.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce function udp_tun_rx_dst() to initialize tunnel dst on
receive path.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On packet transmit path geneve need to lookup route. Following
patch improves route lookup using more parameters.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This enables bridge vlan_protocol to be configured through netlink.
When CONFIG_BRIDGE_VLAN_FILTERING is disabled, kernel behaves the
same way as this feature is not implemented.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds support for 3 new PCI device combinations -
1077:16a1, 1077:16a4 and 1077:16ad.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 62ee783bf1f8 ("smsc911x: Fix crash seen if neither ACPI nor OF is
configured or used") introduces an error check for the return value from
device_get_phy_mode() and bails out if there is an error. Unfortunately,
there are configurations where no phy is configured. Those configurations
now fail.
To fix the problem, accept error returns from device_get_phy_mode(),
and use the return value from device_property_read_u32() to determine
if there is a suitable firmware interface to read the configuration.
Fixes: 62ee783bf1f8 ("smsc911x: Fix crash seen if neither ACPI nor OF is configured or used")
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Return -ENXIO if device property array access functions don't find
a suitable firmware interface.
This lets drivers decide if they should use available platform data
instead.
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For classifiers getting invoked via tc_classify(), we always need an
extra function call into tc_classify_compat(), as both are being
exported as symbols and tc_classify() itself doesn't do much except
handling of reclassifications when tp->classify() returned with
TC_ACT_RECLASSIFY.
CBQ and ATM are the only qdiscs that directly call into tc_classify_compat(),
all others use tc_classify(). When tc actions are being configured
out in the kernel, tc_classify() effectively does nothing besides
delegating.
We could spare this layer and consolidate both functions. pktgen on
single CPU constantly pushing skbs directly into the netif_receive_skb()
path with a dummy classifier on ingress qdisc attached, improves
slightly from 22.3Mpps to 23.1Mpps.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
in sctp_process_asconf(), we get address parameter from the beginning of
the addip params. but we never check if it's really there. if the addr
param is not there, it still can pass sctp_verify_asconf(), then to be
handled by sctp_process_asconf(), it will not be safe.
so add a code in sctp_verify_asconf() to check the address parameter is in
the beginning, or return false to send abort.
note that this can also detect multiple address parameters, and reject it.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No pr_dbg method exists.
While this code is #if 0'd, it'd be nicer to
use the generic hex_dump, so use it instead.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- Rearranged descriptor writes
- Moved increment command write to xgene_enet_setup_tx_desc
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|