aboutsummaryrefslogtreecommitdiffstats
path: root/net/dsa (follow)
AgeCommit message (Collapse)AuthorFilesLines
2019-08-20net: dsa: enable and disable all portsVivien Didelot1-0/+11
Call the .port_enable and .port_disable functions for all ports, not only the user ports, so that drivers may optimize the power consumption of all ports after a successful setup. Unused ports are now disabled on setup. CPU and DSA ports are now enabled on setup and disabled on teardown. User ports were already enabled at slave creation and disabled at slave destruction. Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-20net: dsa: use a single switch statement for port setupVivien Didelot1-48/+39
It is currently difficult to read the different steps involved in the setup and teardown of ports in the DSA code. Keep it simple with a single switch statement for each port type: UNUSED, CPU, DSA, or USER. Also no need to call devlink_port_unregister from within dsa_port_setup as this step is inconditionally handled by dsa_port_teardown on error. Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-19Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netDavid S. Miller1-0/+3
Merge conflict of mlx5 resolved using instructions in merge commit 9566e650bf7fdf58384bb06df634f7531ca3a97e. Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-17net: dsa: remove calls to genphy_config_initHeiner Kallweit1-5/+0
Supported PHY features are either auto-detected or explicitly set. In both cases calling genphy_config_init isn't needed. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-11net: dsa: Check existence of .port_mdb_add callback before calling itChen-Yu Tsai1-0/+3
The dsa framework has optional .port_mdb_{prepare,add,del} callback fields for drivers to handle multicast database entries. When adding an entry, the framework goes through a prepare phase, then a commit phase. Drivers not providing these callbacks should be detected in the prepare phase. DSA core may still bypass the bridge layer and call the dsa_port_mdb_add function directly with no prepare phase or no switchdev trans object, and the framework ends up calling an undefined .port_mdb_add callback. This results in a NULL pointer dereference, as shown in the log below. The other functions seem to be properly guarded. Do the same for .port_mdb_add in dsa_switch_mdb_add_bitmap() as well. 8<--- cut here --- Unable to handle kernel NULL pointer dereference at virtual address 00000000 pgd = (ptrval) [00000000] *pgd=00000000 Internal error: Oops: 80000005 [#1] SMP ARM Modules linked in: rtl8xxxu rtl8192cu rtl_usb rtl8192c_common rtlwifi mac80211 cfg80211 CPU: 1 PID: 134 Comm: kworker/1:2 Not tainted 5.3.0-rc1-00247-gd3519030752a #1 Hardware name: Allwinner sun7i (A20) Family Workqueue: events switchdev_deferred_process_work PC is at 0x0 LR is at dsa_switch_event+0x570/0x620 pc : [<00000000>] lr : [<c08533ec>] psr: 80070013 sp : ee871db8 ip : 00000000 fp : ee98d0a4 r10: 0000000c r9 : 00000008 r8 : ee89f710 r7 : ee98d040 r6 : ee98d088 r5 : c0f04c48 r4 : ee98d04c r3 : 00000000 r2 : ee89f710 r1 : 00000008 r0 : ee98d040 Flags: Nzcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none Control: 10c5387d Table: 6deb406a DAC: 00000051 Process kworker/1:2 (pid: 134, stack limit = 0x(ptrval)) Stack: (0xee871db8 to 0xee872000) 1da0: ee871e14 103ace2d 1dc0: 00000000 ffffffff 00000000 ee871e14 00000005 00000000 c08524a0 00000000 1de0: ffffe000 c014bdfc c0f04c48 ee871e98 c0f04c48 ee9e5000 c0851120 c014bef0 1e00: 00000000 b643aea2 ee9b4068 c08509a8 ee2bf940 ee89f710 ee871ecb 00000000 1e20: 00000008 103ace2d 00000000 c087e248 ee29c868 103ace2d 00000001 ffffffff 1e40: 00000000 ee871e98 00000006 00000000 c0fb2a50 c087e2d0 ffffffff c08523c4 1e60: ffffffff c014bdfc 00000006 c0fad2d0 ee871e98 ee89f710 00000000 c014c500 1e80: 00000000 ee89f3c0 c0f04c48 00000000 ee9e5000 c087dfb4 ee9e5000 00000000 1ea0: ee89f710 ee871ecb 00000001 103ace2d 00000000 c0f04c48 00000000 c087e0a8 1ec0: 00000000 efd9a3e0 0089f3c0 103ace2d ee89f700 ee89f710 ee9e5000 00000122 1ee0: 00000100 c087e130 ee89f700 c0fad2c8 c1003ef0 c087de4c 2e928000 c0fad2ec 1f00: c0fad2ec ee839580 ef7a62c0 ef7a9400 00000000 c087def8 c0fad2ec c01447dc 1f20: ef315640 ef7a62c0 00000008 ee839580 ee839594 ef7a62c0 00000008 c0f03d00 1f40: ef7a62d8 ef7a62c0 ffffe000 c0145b84 ffffe000 c0fb2420 c0bfaa8c 00000000 1f60: ffffe000 ee84b600 ee84b5c0 00000000 ee870000 ee839580 c0145b40 ef0e5ea4 1f80: ee84b61c c014a6f8 00000001 ee84b5c0 c014a5b0 00000000 00000000 00000000 1fa0: 00000000 00000000 00000000 c01010e8 00000000 00000000 00000000 00000000 1fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 1fe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000 [<c08533ec>] (dsa_switch_event) from [<c014bdfc>] (notifier_call_chain+0x48/0x84) [<c014bdfc>] (notifier_call_chain) from [<c014bef0>] (raw_notifier_call_chain+0x18/0x20) [<c014bef0>] (raw_notifier_call_chain) from [<c08509a8>] (dsa_port_mdb_add+0x48/0x74) [<c08509a8>] (dsa_port_mdb_add) from [<c087e248>] (__switchdev_handle_port_obj_add+0x54/0xd4) [<c087e248>] (__switchdev_handle_port_obj_add) from [<c087e2d0>] (switchdev_handle_port_obj_add+0x8/0x14) [<c087e2d0>] (switchdev_handle_port_obj_add) from [<c08523c4>] (dsa_slave_switchdev_blocking_event+0x94/0xa4) [<c08523c4>] (dsa_slave_switchdev_blocking_event) from [<c014bdfc>] (notifier_call_chain+0x48/0x84) [<c014bdfc>] (notifier_call_chain) from [<c014c500>] (blocking_notifier_call_chain+0x50/0x68) [<c014c500>] (blocking_notifier_call_chain) from [<c087dfb4>] (switchdev_port_obj_notify+0x44/0xa8) [<c087dfb4>] (switchdev_port_obj_notify) from [<c087e0a8>] (switchdev_port_obj_add_now+0x90/0x104) [<c087e0a8>] (switchdev_port_obj_add_now) from [<c087e130>] (switchdev_port_obj_add_deferred+0x14/0x5c) [<c087e130>] (switchdev_port_obj_add_deferred) from [<c087de4c>] (switchdev_deferred_process+0x64/0x104) [<c087de4c>] (switchdev_deferred_process) from [<c087def8>] (switchdev_deferred_process_work+0xc/0x14) [<c087def8>] (switchdev_deferred_process_work) from [<c01447dc>] (process_one_work+0x218/0x50c) [<c01447dc>] (process_one_work) from [<c0145b84>] (worker_thread+0x44/0x5bc) [<c0145b84>] (worker_thread) from [<c014a6f8>] (kthread+0x148/0x150) [<c014a6f8>] (kthread) from [<c01010e8>] (ret_from_fork+0x14/0x2c) Exception stack(0xee871fb0 to 0xee871ff8) 1fa0: 00000000 00000000 00000000 00000000 1fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 1fe0: 00000000 00000000 00000000 00000000 00000013 00000000 Code: bad PC value ---[ end trace 1292c61abd17b130 ]--- [<c08533ec>] (dsa_switch_event) from [<c014bdfc>] (notifier_call_chain+0x48/0x84) corresponds to $ arm-linux-gnueabihf-addr2line -C -i -e vmlinux c08533ec linux/net/dsa/switch.c:156 linux/net/dsa/switch.c:178 linux/net/dsa/switch.c:328 Fixes: e6db98db8a95 ("net: dsa: add switch mdb bitmap functions") Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-06Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netDavid S. Miller1-10/+2
Just minor overlapping changes in the conflicts here. Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-06net: dsa: sja1105: Fix memory leak on meta state machine error pathVladimir Oltean1-0/+1
When RX timestamping is enabled and two link-local (non-meta) frames are received in a row, this constitutes an error. The tagger is always caching the last link-local frame, in an attempt to merge it with the meta follow-up frame when that arrives. To recover from the above error condition, the initial cached link-local frame is dropped and the second frame in a row is cached (in expectance of the second meta frame). However, when dropping the initial link-local frame, its backing memory was being leaked. Fixes: f3097be21bf1 ("net: dsa: sja1105: Add a state machine for RX timestamping") Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-06net: dsa: sja1105: Fix memory leak on meta state machine normal pathVladimir Oltean1-10/+1
After a meta frame is received, it is associated with the cached sp->data->stampable_skb from the DSA tagger private structure. Cached means its refcount is incremented with skb_get() in order for dsa_switch_rcv() to not free it when the tagger .rcv returns NULL. The mistake is that skb_unref() is not the correct function to use. It will correctly decrement the refcount (which will go back to zero) but the skb memory will not be freed. That is the job of kfree_skb(), which also calls skb_unref(). But it turns out that freeing the cached stampable_skb is in fact not necessary. It is still a perfectly valid skb, and now it is even annotated with the partial RX timestamp. So remove the skb_copy() altogether and simply pass the stampable_skb with a refcount of 1 (incremented by us, decremented by dsa_switch_rcv) up the stack. Fixes: f3097be21bf1 ("net: dsa: sja1105: Add a state machine for RX timestamping") Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-06net: dsa: dump CPU port regs through masterVivien Didelot1-0/+66
Merge the CPU port registers dump into the master interface registers dump through ethtool, by nesting the ethtool_drvinfo and ethtool_regs structures of the CPU port into the dump. drvinfo->regdump_len will contain the full data length, while regs->len will contain only the master interface registers dump length. This allows for example to dump the CPU port registers on a ZII Dev C board like this: # ethtool -d eth1 0x004: 0x00000000 0x008: 0x0a8000aa 0x010: 0x01000000 0x014: 0x00000000 0x024: 0xf0000102 0x040: 0x6d82c800 0x044: 0x00000020 0x064: 0x40000000 0x084: RCR (Receive Control Register) 0x47c00104 MAX_FL (Maximum frame length) 1984 FCE (Flow control enable) 0 BC_REJ (Broadcast frame reject) 0 PROM (Promiscuous mode) 0 DRT (Disable receive on transmit) 0 LOOP (Internal loopback) 0 0x0c4: TCR (Transmit Control Register) 0x00000004 RFC_PAUSE (Receive frame control pause) 0 TFC_PAUSE (Transmit frame control pause) 0 FDEN (Full duplex enable) 1 HBC (Heartbeat control) 0 GTS (Graceful transmit stop) 0 0x0e4: 0x76735d6d 0x0e8: 0x7e9e8808 0x0ec: 0x00010000 . . . 88E6352 Switch Port Registers ------------------------------ 00: Port Status 0x4d04 Pause Enabled 0 My Pause 1 802.3 PHY Detected 0 Link Status Up Duplex Full Speed 100 or 200 Mbps EEE Enabled 0 Transmitter Paused 0 Flow Control 0 Config Mode 0x4 01: Physical Control 0x003d RGMII Receive Timing Control Default RGMII Transmit Timing Control Default 200 BASE Mode 100 Flow Control's Forced value 0 Force Flow Control 0 Link's Forced value Up Force Link 1 Duplex's Forced value Full Force Duplex 1 Force Speed 100 or 200 Mbps . . . Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-06net: dsa: ksz: Drop NET_DSA_TAG_KSZ9477Marek Vasut1-7/+0
This Kconfig option is unused, drop it. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Andrew Lunn <andrew@lunn.ch> Cc: David S. Miller <davem@davemloft.net> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Tristram Ha <Tristram.Ha@microchip.com> Cc: Vivien Didelot <vivien.didelot@gmail.com> Cc: Woojung Huh <woojung.huh@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-07-30net: dsa: ksz: Add KSZ8795 tag codeTristram Ha1-0/+62
Add DSA tag code for Microchip KSZ8795 switch. The switch is simpler and the tag is only 1 byte, instead of 2 as is the case with KSZ9477. Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com> Signed-off-by: Marek Vasut <marex@denx.de> Cc: Andrew Lunn <andrew@lunn.ch> Cc: David S. Miller <davem@davemloft.net> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Tristram Ha <Tristram.Ha@microchip.com> Cc: Vivien Didelot <vivien.didelot@gmail.com> Cc: Woojung Huh <woojung.huh@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-07-19net: flow_offload: add flow_block structure and use itPablo Neira Ayuso1-1/+1
This object stores the flow block callbacks that are attached to this block. Update flow_block_cb_lookup() to take this new object. This patch restores the block sharing feature. Fixes: da3eeb904ff4 ("net: flow_offload: add list handling functions") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-07-19net: flow_offload: rename tc_setup_cb_t to flow_setup_cb_tPablo Neira Ayuso1-1/+1
Rename this type definition and adapt users. Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-07-19net: flow_offload: remove netns parameter from flow_block_cb_alloc()Pablo Neira Ayuso1-1/+1
No need to annotate the netns on the flow block callback object, flow_block_cb_is_busy() already checks for used blocks. Fixes: d63db30c8537 ("net: flow_offload: add flow_block_cb_alloc() and flow_block_cb_free()") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-07-18net: dsa: sja1105: Fix missing unlock on error in sk_buff()Wei Yongjun1-0/+1
Add the missing unlock before return from function sk_buff() in the error handling case. Fixes: f3097be21bf1 ("net: dsa: sja1105: Add a state machine for RX timestamping") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-07-09net: dsa: add support for BRIDGE_MROUTER attributeVivien Didelot3-0/+17
This patch adds support for enabling or disabling the flooding of unknown multicast traffic on the CPU ports, depending on the value of the switchdev SWITCHDEV_ATTR_ID_BRIDGE_MROUTER attribute. The current behavior is kept unchanged but a user can now prevent the CPU conduit to be flooded with a lot of unregistered traffic that the network stack needs to filter in software with e.g.: echo 0 > /sys/class/net/br0/multicast_router Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-07-09net: flow_offload: add flow_block_cb_is_busy() and use itPablo Neira Ayuso1-0/+3
This patch adds a function to check if flow block callback is already in use. Call this new function from flow_block_cb_setup_simple() and from drivers. Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-07-09drivers: net: use flow block APIPablo Neira Ayuso1-3/+19
This patch updates flow_block_cb_setup_simple() to use the flow block API. Several drivers are also adjusted to use it. This patch introduces the per-driver list of flow blocks to account for blocks that are already in use. Remove tc_block_offload alias. Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-07-09net: flow_offload: rename TCF_BLOCK_BINDER_TYPE_* to FLOW_BLOCK_BINDER_TYPE_*Pablo Neira Ayuso1-2/+2
Rename from TCF_BLOCK_BINDER_TYPE_* to FLOW_BLOCK_BINDER_TYPE_* and remove temporary tcf_block_binder_type alias. Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-07-09net: flow_offload: rename TC_BLOCK_{UN}BIND to FLOW_BLOCK_{UN}BINDPablo Neira Ayuso1-2/+2
Rename from TC_BLOCK_{UN}BIND to FLOW_BLOCK_{UN}BIND and remove temporary tc_block_command alias. Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-14net: dsa: use switchdev handle helpersVivien Didelot1-44/+32
Get rid of the dsa_slave_switchdev_port_{attr_set,obj}_event functions in favor of the switchdev_handle_port_{attr_set,obj_add,obj_del} helpers which recurse into the lower devices of the target interface. This has the benefit of being aware of the operations made on the bridge device itself, where orig_dev is the bridge, and dev is the slave. This can be used later to configure the hardware switches. Only VLAN and (port) MDB objects not directly targeting the slave device are unsupported at the moment, so skip this case in their respective case statements. Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-14net: dsa: make dsa_slave_dev_check use constVivien Didelot1-2/+2
The switchdev handle helpers make use of a device checking helper requiring a const net_device. Make dsa_slave_dev_check compliant to this. Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-14net: dsa: do not check orig_dev in vlan delVivien Didelot1-9/+0
The current DSA code handling switchdev objects does not recurse into the lower devices thus is never called with an orig_dev member being a bridge device, hence remove this useless check. At the same time, remove the comments about the callers, which is unlikely to be updated if the code changes and thus will be confusing. Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-13net: dsa: tag_sja1105: Select CONFIG_PACKINGVladimir Oltean1-0/+1
The packing facility is needed to decode Ethernet meta frames containing source port and RX timestamping information. The DSA driver selects CONFIG_PACKING, but the tagger did not, and since taggers can be now compiled as modules independently from the drivers themselves, this is an issue now, as CONFIG_PACKING is disabled by default on all architectures. Fixes: e53e18a6fe4d ("net: dsa: sja1105: Receive and decode meta frames") Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Reported-by: Randy Dunlap <rdunlap@infradead.org> Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-12net: dsa: Deal with non-existing PHY/fixed-linkFlorian Fainelli1-1/+1
We need to specifically deal with phylink_of_phy_connect() returning -ENODEV, because this can happen when a CPU/DSA port does connect neither to a PHY, nor has a fixed-link property. This is a valid use case that is permitted by the binding and indicates to the switch: auto-configure port with maximum capabilities. Fixes: 0e27921816ad ("net: dsa: Use PHYLINK for the CPU/DSA ports") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-08net: dsa: sja1105: Add a state machine for RX timestampingVladimir Oltean1-1/+120
Meta frame reception relies on the hardware keeping its promise that it will send no other traffic towards the CPU port between a link-local frame and a meta frame. Otherwise there is no other way to associate the meta frame with the link-local frame it's holding a timestamp of. The receive function is made stateful, and buffers a timestampable frame until its meta frame arrives, then merges the two, drops the meta and releases the link-local frame up the stack. Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-08net: dsa: sja1105: Receive and decode meta framesVladimir Oltean1-3/+41
This adds support in the tagger for understanding the source port and switch id of meta frames. Their timestamp is also extracted but not used yet - this needs to be done in a state machine that modifies the previously received timestampable frame - will be added in a follow-up patch. Also take the opportunity to: - Remove a comment in sja1105_filter made obsolete by e8d67fa5696e ("net: dsa: sja1105: Don't store frame type in skb->cb") - Reorder the checks in sja1105_filter to optimize for the most likely scenario first: regular traffic. Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-08net: dsa: sja1105: Make sja1105_is_link_local not match meta framesVladimir Oltean1-0/+2
Although meta frames are configured to be sent at SJA1105_META_DMAC (01-80-C2-00-00-0E) which is a multicast MAC address that would also be trapped by the switch to the CPU, were it to receive it on a front-panel port, meta frames are conceptually not link-local frames, they only carry their RX timestamps. The choice of sending meta frames at a multicast DMAC is a pragmatic one, to avoid installing an extra entry to the DSA master port's multicast MAC filter. Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-08net: dsa: sja1105: Build a minimal understanding of meta framesVladimir Oltean1-0/+15
Meta frames are sent on the CPU port by the switch if RX timestamping is enabled. They contain a partial timestamp of the previous frame. They are Ethernet frames with the Ethernet header constructed out of: - SJA1105_META_DMAC - SJA1105_META_SMAC - ETH_P_SJA1105_META The Ethernet payload will be decoded in a follow-up patch. Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-08net: dsa: sja1105: Limit use of incl_srcpt to bridge+vlan modeVladimir Oltean1-7/+11
The incl_srcpt setting makes the switch mangle the destination MACs of multicast frames trapped to the CPU - a primitive tagging mechanism that works even when we cannot use the 802.1Q software features. The downside is that the two multicast MAC addresses that the switch traps for L2 PTP (01-80-C2-00-00-0E and 01-1B-19-00-00-00) quickly turn into a lot more, as the switch encodes the source port and switch id into bytes 3 and 4 of the MAC. The resulting range of MAC addresses would need to be installed manually into the DSA master port's multicast MAC filter, and even then, most devices might not have a large enough MAC filtering table. As a result, only limit use of incl_srcpt to when it's strictly necessary: when under a VLAN filtering bridge. This fixes PTP in non-bridged mode (standalone ports). Otherwise, PTP frames, as well as metadata follow-up frames holding RX timestamps won't be received because they will be blocked by the master port's MAC filter. Linuxptp doesn't help, because it only requests the addition of the unmodified PTP MACs to the multicast filter. This issue is not seen in bridged mode because the master port is put in promiscuous mode when the slave ports are enslaved to a bridge. Therefore, there is no downside to having the incl_srcpt mechanism active there. Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-08net: dsa: tag_8021q: Create helper function for removing VLAN headerVladimir Oltean2-30/+46
This removes the existing implementation from tag_sja1105, which was partially incorrect (it was not changing the MAC header offset, thereby leaving it to point 4 bytes earlier than it should have). This overwrites the VLAN tag by moving the Ethernet source and destination MACs 4 bytes to the right. Then skb->data (assumed to be pointing immediately after the EtherType) is temporarily pushed to the beginning of the new Ethernet header, the new Ethernet header offset and length are recorded, then skb->data is moved back to where it was. Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-08net: dsa: Add teardown callback for driversVladimir Oltean1-0/+3
This is helpful for e.g. draining per-driver (not per-port) tagger queues. Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-08net: dsa: Keep a pointer to the skb clone for TX timestampingVladimir Oltean1-0/+3
For drivers that use deferred_xmit for PTP frames (such as sja1105), there is no need to perform matching between PTP frames and their egress timestamps, since the sending process can be serialized. In that case, it makes sense to have the pointer to the skb clone that DSA made directly in the skb->cb. It will be used for pushing the egress timestamp back in the application socket's error queue. Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-07Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller8-42/+10
Some ISDN files that got removed in net-next had some changes done in mainline, take the removals. Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-07Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds1-7/+3
Pull networking fixes from David Miller: 1) Free AF_PACKET po->rollover properly, from Willem de Bruijn. 2) Read SFP eeprom in max 16 byte increments to avoid problems with some SFP modules, from Russell King. 3) Fix UDP socket lookup wrt. VRF, from Tim Beale. 4) Handle route invalidation properly in s390 qeth driver, from Julian Wiedmann. 5) Memory leak on unload in RDS, from Zhu Yanjun. 6) sctp_process_init leak, from Neil HOrman. 7) Fix fib_rules rule insertion semantic change that broke Android, from Hangbin Liu. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (33 commits) pktgen: do not sleep with the thread lock held. net: mvpp2: Use strscpy to handle stat strings net: rds: fix memory leak in rds_ib_flush_mr_pool ipv6: fix EFAULT on sendto with icmpv6 and hdrincl ipv6: use READ_ONCE() for inet->hdrincl as in ipv4 Revert "fib_rules: return 0 directly if an exactly same rule exists when NLM_F_EXCL not supplied" net: aquantia: fix wol configuration not applied sometimes ethtool: fix potential userspace buffer overflow Fix memory leak in sctp_process_init net: rds: fix memory leak when unload rds_rdma ipv6: fix the check before getting the cookie in rt6_get_cookie ipv4: not do cache for local delivery if bc_forwarding is enabled s390/qeth: handle error when updating TX queue count s390/qeth: fix VLAN attribute in bridge_hostnotify udev event s390/qeth: check dst entry before use s390/qeth: handle limited IPv4 broadcast in L3 TX path net: fix indirect calls helpers for ptype list hooks. net: ipvlan: Fix ipvlan device tso disabled while NETIF_F_IP_CSUM is set udp: only choose unbound UDP socket for multicast when not in a VRF net/tls: replace the sleeping lock around RX resync with a bit lock ...
2019-05-31net: dsa: sja1105: Don't store frame type in skb->cbVladimir Oltean1-7/+3
Due to a confusion I thought that eth_type_trans() was called by the network stack whereas it can actually be called by network drivers to figure out the skb protocol and next packet_type handlers. In light of the above, it is not safe to store the frame type from the DSA tagger's .filter callback (first entry point on RX path), since GRO is yet to be invoked on the received traffic. Hence it is very likely that the skb->cb will actually get overwritten between eth_type_trans() and the actual DSA packet_type handler. Of course, what this patch fixes is the actual overwriting of the SJA1105_SKB_CB(skb)->type field from the GRO layer, which made all frames be seen as SJA1105_FRAME_TYPE_NORMAL (0). Fixes: 227d07a07ef1 ("net: dsa: sja1105: Add support for traffic through standalone ports") Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-31Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller1-14/+65
The phylink conflict was between a bug fix by Russell King to make sure we have a consistent PHY interface mode, and a change in net-next to pull some code in phylink_resolve() into the helper functions phylink_mac_link_{up,down}() On the dp83867 side it's mostly overlapping changes, with the 'net' side removing a condition that was supposed to trigger for RGMII but because of how it was coded never actually could trigger. Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-31Merge tag 'spdx-5.2-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-coreLinus Torvalds7-35/+7
Pull yet more SPDX updates from Greg KH: "Here is another set of reviewed patches that adds SPDX tags to different kernel files, based on a set of rules that are being used to parse the comments to try to determine that the license of the file is "GPL-2.0-or-later" or "GPL-2.0-only". Only the "obvious" versions of these matches are included here, a number of "non-obvious" variants of text have been found but those have been postponed for later review and analysis. There is also a patch in here to add the proper SPDX header to a bunch of Kbuild files that we have missed in the past due to new files being added and forgetting that Kbuild uses two different file names for Makefiles. This issue was reported by the Kbuild maintainer. These patches have been out for review on the linux-spdx@vger mailing list, and while they were created by automatic tools, they were hand-verified by a bunch of different people, all whom names are on the patches are reviewers" * tag 'spdx-5.2-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (82 commits) treewide: Add SPDX license identifier - Kbuild treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 225 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 224 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 223 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 222 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 221 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 220 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 218 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 217 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 216 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 215 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 214 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 213 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 211 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 210 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 209 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 207 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 206 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 203 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 201 ...
2019-05-30net: dsa: Add error path handling in dsa_tree_setup()Ioana Ciornei1-23/+66
In case a call to dsa_tree_setup() fails, an attempt to cleanup is made by calling dsa_tree_remove_switch(), which should take care of removing/unregistering any resources previously allocated. This does not happen because it is conditioned by dst->setup being true, which is set only after _all_ setup steps were performed successfully. This is especially interesting when the internal MDIO bus is registered but afterwards, a port setup fails and the mdiobus_unregister() is never called. This leads to a BUG_ON() complaining about the fact that it's trying to free an MDIO bus that's still registered. Add proper error handling in all functions branching from dsa_tree_setup(). Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Reported-by: kernel test robot <rong.a.chen@intel.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-30net: dsa: tag_8021q: Create a stable binary formatVladimir Oltean1-10/+50
Tools like tcpdump need to be able to decode the significance of fake VLAN headers that DSA uses to separate switch ports. But currently these have no global significance - they are simply an ordered list of DSA_MAX_SWITCHES x DSA_MAX_PORTS numbers ending at 4095. The reason why this is submitted as a fix is that the existing mapping of VIDs should not enter into a stable kernel, so we can pretend that only the new format exists. This way tcpdump won't need to try to make something out of the VLAN tags on 5.2 kernels. Fixes: f9bbe4477c30 ("net: dsa: Optional VLAN-based port separation for switches without tagging") Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-30net: dsa: tag_8021q: Change order of rx_vid setupIoana Ciornei1-4/+15
The 802.1Q tagging performs an unbalanced setup in terms of RX VIDs on the CPU port. For the ingress path of a 802.1Q switch to work, the RX VID of a port needs to be seen as tagged egress on the CPU port. While configuring the other front-panel ports to be part of this VID, for bridge scenarios, the untagged flag is applied even on the CPU port in dsa_switch_vlan_add. This happens because DSA applies the same flags on the CPU port as on the (bridge-controlled) slave ports, and the effect in this case is that the CPU port tagged settings get deleted. Instead of fixing DSA by introducing a way to control VLAN flags on the CPU port (and hence stop inheriting from the slave ports) - a hard, perhaps intractable problem - avoid this situation by moving the setup part of the RX VID on the CPU port after all the other front-panel ports have been added to the VID. Fixes: f9bbe4477c30 ("net: dsa: Optional VLAN-based port separation for switches without tagging") Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-30treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 152Thomas Gleixner7-35/+7
Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or at your option any later version extracted by the scancode license scanner the SPDX license identifier GPL-2.0-or-later has been chosen to replace the boilerplate/reference in 3029 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-29net: dsa: Use PHYLINK for the CPU/DSA portsIoana Ciornei1-6/+63
For DSA switches that do not have an .adjust_link callback, aka those who transitioned totally to the PHYLINK-compliant API, use PHYLINK to drive the CPU/DSA ports. The PHYLIB usage and .adjust_link are kept but deprecated, and users are asked to transition from it. The reason why we can't do anything for them is because PHYLINK does not wrap the fixed-link state behind a phydev object, so we cannot wrap .phylink_mac_config into .adjust_link unless we fabricate a phy_device structure. For these ports, the newly introduced PHYLINK_DEV operation type is used and the dsa_switch device structure is passed to PHYLINK for printing purposes. The handling of the PHYLINK_NETDEV and PHYLINK_DEV PHYLINK instances is common from the perspective of the driver. Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-29net: dsa: Move the phylink driver calls into port.cIoana Ciornei3-95/+118
In order to have a common handling of PHYLINK for the slave and non-user ports, the DSA core glue logic (between PHYLINK and the driver) must use an API that does not rely on a struct net_device. These will also be called by the CPU-port-handling code in a further patch. Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Suggested-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-29net: phylink: Add struct phylink_config to PHYLINK APIIoana Ciornei1-13/+18
The phylink_config structure will encapsulate a pointer to a struct device and the operation type requested for this instance of PHYLINK. This patch does not make any functional changes, it just transitions the PHYLINK internals and all its users to the new API. A pointer to a phylink_config structure will be passed to phylink_create() instead of the net_device directly. Also, the same phylink_config pointer will be passed back to all phylink_mac_ops callbacks instead of the net_device. Using this mechanism, a PHYLINK user can get the original net_device using a structure such as 'to_net_dev(config->dev)' or directly the structure containing the phylink_config using a container_of call. At the moment, only the PHYLINK_NETDEV is defined as a valid operation type for PHYLINK. In this mode, a valid reference to a struct device linked to the original net_device should be passed to PHYLINK through the phylink_config structure. This API changes is mainly driven by the necessity of adding a new operation type in PHYLINK that disconnects the phy_device from the net_device and also works when the net_device is lacking. Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-21treewide: Add SPDX license identifier - Makefile/KconfigThomas Gleixner1-0/+1
Add SPDX license identifiers to all Make/Kconfig files which: - Have no license information of any form These files fall under the project license, GPL v2 only. The resulting SPDX license identifier is: GPL-2.0-only Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-12net: dsa: Initialize DSA_SKB_CB(skb)->deferred_xmit variableVladimir Oltean1-0/+2
The sk_buff control block can have any contents on xmit put there by the stack, so initialization is mandatory, since we are checking its value after the actual DSA xmit (the tagger may have changed it). The DSA_SKB_ZERO() macro could have been used for this purpose, but: - Zeroizing a 48-byte memory region in the hotpath is best avoided. - It would have triggered a warning with newer compilers since __dsa_skb_cb contains a structure within a structure, and the {0} initializer was incorrect for that purpose. So simply remove the DSA_SKB_ZERO() macro and initialize the deferred_xmit variable by hand (which should be done for all further dsa_skb_cb variables which need initialization - currently none - to avoid the performance penalty). Fixes: 97a69a0dea9a ("net: dsa: Add support for deferred xmit") Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-10dsa: tag_brcm: Fix build error without CONFIG_NET_DSA_TAG_BRCM_PREPENDYueHaibing1-1/+1
Fix gcc build error: net/dsa/tag_brcm.c:211:16: error: brcm_prepend_netdev_ops undeclared here (not in a function); did you mean brcm_netdev_ops? DSA_TAG_DRIVER(brcm_prepend_netdev_ops); ^ ./include/net/dsa.h:708:10: note: in definition of macro DSA_TAG_DRIVER .ops = &__ops, \ ^~~~~ ./include/net/dsa.h:701:36: warning: dsa_tag_driver_brcm_prepend_netdev_ops defined but not used [-Wunused-variable] #define DSA_TAG_DRIVER_NAME(__ops) dsa_tag_driver ## _ ## __ops ^ ./include/net/dsa.h:707:30: note: in expansion of macro DSA_TAG_DRIVER_NAME static struct dsa_tag_driver DSA_TAG_DRIVER_NAME(__ops) = { \ ^~~~~~~~~~~~~~~~~~~ net/dsa/tag_brcm.c:211:1: note: in expansion of macro DSA_TAG_DRIVER DSA_TAG_DRIVER(brcm_prepend_netdev_ops); Like the CONFIG_NET_DSA_TAG_BRCM case, brcm_prepend_netdev_ops and DSA_TAG_PROTO_BRCM_PREPEND should be wrappeed by CONFIG_NET_DSA_TAG_BRCM_PREPEND. Reported-by: Hulk Robot <hulkci@huawei.com> Fixes: b74b70c44986 ("net: dsa: Support prepended Broadcom tag") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-07Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller1-1/+6
Minor conflict with the DSA legacy code removal. Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-07net: dsa: support of_get_mac_address new ERR_PTR errorPetr Štetiar1-1/+1
There was NVMEM support added to of_get_mac_address, so it could now return ERR_PTR encoded error values, so we need to adjust all current users of of_get_mac_address to this new fact. While at it, remove superfluous is_valid_ether_addr as the MAC address returned from of_get_mac_address is always valid and checked by is_valid_ether_addr anyway. Fixes: d01f449c008a ("of_net: add NVMEM support to of_get_mac_address") Signed-off-by: Petr Štetiar <ynezz@true.cz> Tested-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.