aboutsummaryrefslogtreecommitdiffstats
path: root/net/ethernet (unfollow)
AgeCommit message (Collapse)AuthorFilesLines
2013-10-19ipv4: gso: make inet_gso_segment() stackableEric Dumazet3-9/+25
In order to support GSO on IPIP, we need to make inet_gso_segment() stackable. It should not assume network header starts right after mac header. Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-19ipv4: generalize gre_handle_offloadsEric Dumazet4-30/+43
This patch makes gre_handle_offloads() more generic and rename it to iptunnel_handle_offloads() This will be used to add GSO/TSO support to IPIP tunnels. Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-19net: generalize skb_segment()Eric Dumazet1-17/+5
While implementing GSO/TSO support for IPIP, I found skb_segment() was assuming network header was immediately following mac header. Its not really true in the case inet_gso_segment() is stacked : By the time tcp_gso_segment() is called, network header points to the inner IP header. Let's instead assume nothing and pick the current offsets found in original skb, we have skb_headers_offset_update() helper for that. Also move the csum_start update inside skb_headers_offset_update() Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-19ipv6: gso: remove redundant lockingEric Dumazet1-4/+1
ipv6_gso_send_check() and ipv6_gso_segment() are called by skb_mac_gso_segment() under rcu lock, no need to use rcu_read_lock() / rcu_read_unlock() Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-19be2net: Rework PCIe error report log messagingAjit Khaparde1-3/+5
Currently we log a message whenever pcie_enable_error_reporting fails. The message clutters up logs, especially when we don't support it for VFs. Instead enable this only for PFs and log a message when the call succeeds. Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-19net: misc: Remove extern from function prototypesJoe Perches11-167/+157
There are a mix of function prototypes with and without extern in the kernel sources. Standardize on not using extern for function prototypes. Function prototypes don't need to be written with extern. extern is assumed by the compiler. Its use is as unnecessary as using auto to declare automatic/local variables in a block. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-19net: ipv4/ipv6: Remove extern from function prototypesJoe Perches4-59/+54
There are a mix of function prototypes with and without extern in the kernel sources. Standardize on not using extern for function prototypes. Function prototypes don't need to be written with extern. extern is assumed by the compiler. Its use is as unnecessary as using auto to declare automatic/local variables in a block. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-19net: dccp: Remove extern from function prototypesJoe Perches7-158/+148
There are a mix of function prototypes with and without extern in the kernel sources. Standardize on not using extern for function prototypes. Function prototypes don't need to be written with extern. extern is assumed by the compiler. Its use is as unnecessary as using auto to declare automatic/local variables in a block. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-19net: 8021q/bluetooth/bridge/can/ceph: Remove extern from function prototypesJoe Perches8-219/+194
There are a mix of function prototypes with and without extern in the kernel sources. Standardize on not using extern for function prototypes. Function prototypes don't need to be written with extern. extern is assumed by the compiler. Its use is as unnecessary as using auto to declare automatic/local variables in a block. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-19ipv4: gso: send_check() & segment() cleanupsEric Dumazet1-13/+11
inet_gso_segment() and inet_gso_send_check() are called by skb_mac_gso_segment() under rcu lock, no need to use rcu_read_lock() / rcu_read_unlock() Avoid calling ip_hdr() twice per function. We can use ip_send_check() helper. Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-19bonding: Remove __exit tag from bond_netlink_fini().David S. Miller1-1/+1
It can be called from the module init function, so it cannot be in the exit section. Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-19bonding: add Netlink support active_slave optionJiri Pirko2-1/+23
Signed-off-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-19bonding: add Netlink support mode optionJiri Pirko2-0/+66
Signed-off-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-19bonding: move active_slave getting into separate functionJiri Pirko3-4/+24
Signed-off-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-19bonding: remove bond_ioctl_change_active()Jiri Pirko1-57/+2
no longer needed since bond_option_active_slave_set() can be used instead. Signed-off-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-19bonding: move active_slave setting into separate functionJiri Pirko3-61/+83
Do a bit of refactoring on the way. Signed-off-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-19bonding: move mode setting into separate functionJiri Pirko4-37/+74
Signed-off-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-19bonding: push Netlink bits into separate fileJiri Pirko4-28/+67
Signed-off-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-18em_ipset: use dev_net() accessorstephen hemminger1-2/+2
Randy found that if network namespace not enabled then nd_net does not exist and would cause compilation failure. This is handled correctly by using the dev_net() macro. Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Acked-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-18tcp: remove redundant code in __tcp_retransmit_skb()Neal Cardwell1-15/+0
Remove the specialized code in __tcp_retransmit_skb() that tries to trim any ACKed payload preceding a FIN before we retransmit (this was added in 1999 in v2.2.3pre3). This trimming code was made unreachable by the more general code added above it that uses tcp_trim_head() to trim any ACKed payload, with or without a FIN (this was added in "[NET]: Add segmentation offload support to TCP." in 2002 circa v2.5.33). Signed-off-by: Neal Cardwell <ncardwell@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Yuchung Cheng <ycheng@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Acked-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-18gianfar: Simplify MQ polling to avoid soft lockupClaudiu Manoil1-49/+38
Under certain low traffic conditions, the single core devices with multiple Rx/Tx queues (MQ mode) may reach soft lockup due to gfar_poll not returning in proper time. The following exception was obtained using iperf on a 100Mbit half-duplex link, for a p1010 single core device: BUG: soft lockup - CPU#0 stuck for 23s! [iperf:2847] Modules linked in: CPU: 0 PID: 2847 Comm: iperf Not tainted 3.12.0-rc3 #16 task: e8bf8000 ti: eeb16000 task.ti: ee646000 NIP: c0255b6c LR: c0367ae8 CTR: c0461c18 REGS: eeb17e70 TRAP: 0901 Not tainted (3.12.0-rc3) MSR: 00029000 <CE,EE,ME> CR: 44228428 XER: 20000000 GPR00: c0367ad4 eeb17f20 e8bf8000 ee01f4b4 00000008 ffffffff ffffffff 00000000 GPR08: 000000c0 00000008 000000ff ffffffc0 000193fe NIP [c0255b6c] find_next_bit+0xb8/0xc4 LR [c0367ae8] gfar_poll+0xc8/0x1d8 Call Trace: [eeb17f20] [c0367ad4] gfar_poll+0xb4/0x1d8 (unreliable) [eeb17f70] [c0422100] net_rx_action+0xa4/0x158 [eeb17fa0] [c003ec6c] __do_softirq+0xcc/0x17c [eeb17ff0] [c000c28c] call_do_softirq+0x24/0x3c [ee647cc0] [c0004660] do_softirq+0x6c/0x94 [ee647ce0] [c003eb9c] local_bh_enable+0x9c/0xa0 [ee647cf0] [c0454fe8] tcp_prequeue_process+0xa4/0xdc [ee647d10] [c0457e44] tcp_recvmsg+0x498/0x96c [ee647d80] [c047b630] inet_recvmsg+0x40/0x64 [ee647da0] [c040ca8c] sock_recvmsg+0x90/0xc0 [ee647e30] [c040edb8] SyS_recvfrom+0x98/0xfc To prevent this, the outer while() loop has been removed allowing gfar_poll() to return faster even if there's still budget left. Also, there's no need to recompute the budget per Rx queue anymore. Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-18fib: Use const struct nl_info * in rtmsg_fibJoe Perches2-2/+2
The rtmsg_fib function doesn't modify this argument so mark it const. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-18ax25: cleanup a range testDan Carpenter1-1/+1
The current test works fine in practice. The "amount" variable is actually used as a boolean so negative values or any non-zero values count as "true". However since we don't allow numbers greater than one, let's not allow negative numbers either. Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-18fib_trie: remove duplicated rcu lockbaker.zhang1-2/+0
fib_table_lookup has included the rcu lock protection. Signed-off-by: baker.zhang <baker.kernel@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-18qlcnic: update version to 5.3.51Himanshu Madhani1-2/+2
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-18qlcnic: Skip unknown entry type while collecting firmware dumpShahed Shaikh1-22/+19
o Driver aborts the minidump collection operation when it finds an unknown entry opcode. This patch skips unknown entry type and resumes the minidump collection operation. o Removed a comparision of collected dump size with expected dump size. Size may differ when driver decides to skip an entry. Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-18qlcnic: dcb code cleanup and refactoring.Sucheta Chakraborty8-228/+207
o Move dcb specific function definitions to dcb files. o Move dcb specific variables to qlcnic_dcb structure. Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-18qlcnic: Remove redundant eSwitch enable commandsSony Chacko3-26/+12
When more than one NIC physical functions are enabled on a port, eSwitch on that port gets enabled automatically. Driver need not explicitly enable the eSwitch. Signed-off-by: Sony Chacko <sony.chacko@qlogic.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-18qlcnic: Update ethtool standard pause settings.Jitendra Kalsaria2-3/+18
Update ethtool standard pause parameter settings and display Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-18qlcnic: Firmware dump collection when auto recovery is disabled.Pratik Pujar2-1/+17
o Allow collecting the firmware dump of halted firmware when auto recovery is disabled. Signed-off-by: Pratik Pujar <pratik.pujar@qlogic.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-18qlcnic: Enhance ethtool to display ring indices and interrupt maskPratik Pujar2-18/+44
o Updated ethtool -d <ethX> option to display ring indices for Transmit(Tx), Receive(Rx), and Status(St) rings. o Updated ethtool -d <ethX> option to display ring interrupt mask for Transmit(Tx), and Status(St) rings. Signed-off-by: Pratik Pujar <pratik.pujar@qlogic.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-18qlcnic: Print informational messages only once during driver load.Sucheta Chakraborty4-16/+22
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-18tcp: rename tcp_tso_segment()Eric Dumazet3-5/+5
Rename tcp_tso_segment() to tcp_gso_segment(), to better reflect what is going on, and ease grep games. Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-18tipc: simplify the link lookup routineErik Hugne1-97/+13
When checking statistics or changing parameters on a link, the link_find_link function is used to locate the link with a given name. The complex method of deconstructing the name into local and remote address/interface is error prone and may fail if the interface names contains special characters. We change the lookup method to iterate over the list of nodes and compare the link names. Signed-off-by: Erik Hugne <erik.hugne@ericsson.com> Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-18tipc: correct return value of link_cmd_set_value routineYing Xue1-9/+19
link_cmd_set_value() takes commands for link, bearer and media related configuration. Genereally the function returns 0 when a command is recognized, and -EINVAL when it is not. However, in the switch for link related commands it returns 0 even when the command is unrecognized. This will sometimes make it look as if a failed configuration command has been successful, but has otherwise no negative effects. We remove this anomaly by returning -EINVAL even for link commands. We also rework all three switches to make them conforming to common kernel coding style. Signed-off-by: Ying Xue <ying.xue@windriver.com> Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-18tipc: correct return value of recv_msg routineYing Xue2-6/+6
Currently, rcv_msg() always returns zero on a packet delivery upcall from net_device. To make its behavior more compliant with the way this API should be used, we change this to let it return NET_RX_SUCCESS (which is zero anyway) when it is able to handle the packet, and NET_RX_DROP otherwise. The latter does not imply any functional change, it only enables the driver to keep more accurate statistics about the fate of delivered packets. Signed-off-by: Ying Xue <ying.xue@windriver.com> Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-18tipc: avoid unnecessary lookup for tipc bearer instanceYing Xue4-18/+10
tipc_block_bearer() currently takes a bearer name (const char*) as argument. This requires the function to make a lookup to find the pointer to the corresponding bearer struct. In the current code base this is not necessary, since the only two callers (tipc_continue(),recv_notification()) already have validated copies of this pointer, and hence can pass it directly in the function call. We change tipc_block_bearer() to directly take struct tipc_bearer* as argument instead. Signed-off-by: Ying Xue <ying.xue@windriver.com> Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-18tipc: make bearer and media naming consistentYing Xue4-57/+57
TIPC 'bearer' exists as an abstract concept, while 'media' is deemed a specific implementation of a bearer, such as Ethernet or Infiniband media. When a component inside TIPC wants to control a specific media, it only needs to access the generic bearer API to achieve this. However, in the current media implementations, the 'bearer' name is also extensively used in media specific function and variable names. This may create confusion, so we choose to replace the term 'bearer' with 'media' in all function names, variable names, and prefixes where this is what really is meant. Note that this change is cosmetic only, and no runtime behaviour changes are made here. Signed-off-by: Ying Xue <ying.xue@windriver.com> Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-18tipc: silence sparse warningsYing Xue2-5/+5
Eliminate below sparse warnings: net/tipc/link.c:1210:37: warning: cast removes address space of expression net/tipc/link.c:1218:59: warning: incorrect type in argument 2 (different address spaces) net/tipc/link.c:1218:59: expected void const [noderef] <asn:1>*from net/tipc/link.c:1218:59: got unsigned char const [usertype] *[assigned] sect_crs net/tipc/socket.c:341:49: warning: Using plain integer as NULL pointer net/tipc/socket.c:1371:36: warning: Using plain integer as NULL pointer net/tipc/socket.c:1694:57: warning: Using plain integer as NULL pointer Signed-off-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Andreas Bofjäll <andreas.bofjall@ericsson.com> Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-18tipc: remove iovec length parameter from all sending functionsYing Xue7-78/+49
tipc_msg_build() now copies message data from iovec to skb_buff using memcpy_fromiovecend(), which doesn't need to be passed the iovec length to perform the copying. So we remove the parameter indicating iovec length in all functions where TIPC messages are built and sent. Signed-off-by: Ying Xue <ying.xue@windriver.com> Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-18tipc: don't use memcpy to copy from user spaceYing Xue1-13/+9
tipc_msg_build() calls skb_copy_to_linear_data_offset() to copy data from user space to kernel space. However, the latter function does in its turn call memcpy() to perform the actual copying. This poses an obvious security and robustness risk, since memcpy() never makes any validity check on the pointer it is copying from. To correct this, we the replace the offending function call with a call to memcpy_fromiovecend(), which uses copy_from_user() to perform the copying. Signed-off-by: Ying Xue <ying.xue@windriver.com> Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-18net: Delete trailing semi-colon from definition of netdev_WARN()Ben Hutchings1-1/+1
Macro definitions should not normally end with a semi-colon, as this makes it dangerous to use them an if...else statement. Happily this has not happened yet. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-18net: refactor sk_page_frag_refill()Eric Dumazet2-4/+25
While working on virtio_net new allocation strategy to increase payload/truesize ratio, we found that refactoring sk_page_frag_refill() was needed. This patch splits sk_page_frag_refill() into two parts, adding skb_page_frag_refill() which can be used without a socket. While we are at it, add a minimum frag size of 32 for sk_page_frag_refill() Michael will either use netdev_alloc_frag() from softirq context, or skb_page_frag_refill() from process context in refill_work() (GFP_KERNEL allocations) Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Michael Dalton <mwdalton@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-18net: enic: remove unnecessary pci_set_drvdata()Jingoo Han1-2/+0
The driver core clears the driver data to NULL after device_release or on probe failure. Thus, it is not needed to manually clear the device driver data to NULL. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-18net: cxgb4vf: remove unnecessary pci_set_drvdata()Jingoo Han1-3/+0
The driver core clears the driver data to NULL after device_release or on probe failure. Thus, it is not needed to manually clear the device driver data to NULL. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-18net: cxgb2: remove unnecessary pci_set_drvdata()Jingoo Han1-2/+0
The driver core clears the driver data to NULL after device_release or on probe failure. Thus, it is not needed to manually clear the device driver data to NULL. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-18net: cxgb3: remove unnecessary pci_set_drvdata()Jingoo Han1-2/+0
The driver core clears the driver data to NULL after device_release or on probe failure. Thus, it is not needed to manually clear the device driver data to NULL. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-18net: cxgb4: remove unnecessary pci_set_drvdata()Jingoo Han1-2/+0
The driver core clears the driver data to NULL after device_release or on probe failure. Thus, it is not needed to manually clear the device driver data to NULL. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-18net: bna: remove unnecessary pci_set_drvdata()Jingoo Han1-1/+0
The driver core clears the driver data to NULL after device_release or on probe failure. Thus, it is not needed to manually clear the device driver data to NULL. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-18net: tg3: remove unnecessary pci_set_drvdata()Jingoo Han1-2/+0
The driver core clears the driver data to NULL after device_release or on probe failure. Thus, it is not needed to manually clear the device driver data to NULL. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.