aboutsummaryrefslogtreecommitdiffstats
path: root/net/ipv4/sysctl_net_ipv4.c (follow)
AgeCommit message (Collapse)AuthorFilesLines
2019-03-21ipv4: Allow amount of dirty memory from fib resizing to be controllableDavid Ahern1-0/+9
fib_trie implementation calls synchronize_rcu when a certain amount of pages are dirty from freed entries. The number of pages was determined experimentally in 2009 (commit c3059477fce2d). At the current setting, synchronize_rcu is called often -- 51 times in a second in one test with an average of an 8 msec delay adding a fib entry. The total impact is a lot of slow down modifying the fib. This is seen in the output of 'time' - the difference between real time and sys+user. For example, using 720,022 single path routes and 'ip -batch'[1]: $ time ./ip -batch ipv4/routes-1-hops real 0m14.214s user 0m2.513s sys 0m6.783s So roughly 35% of the actual time to install the routes is from the ip command getting scheduled out, most notably due to synchronize_rcu (this is observed using 'perf sched timehist'). This patch makes the amount of dirty memory configurable between 64k where the synchronize_rcu is called often (small, low end systems that are memory sensitive) to 64M where synchronize_rcu is called rarely during a large FIB change (for high end systems with lots of memory). The default is 512kB which corresponds to the current setting of 128 pages with a 4kB page size. As an example, at 16MB the worst interval shows 4 calls to synchronize_rcu in a second blocking for up to 30 msec in a single instance, and a total of almost 100 msec across the 4 calls in the second. The trade off is allowing FIB entries to consume more memory in a given time window but but with much better fib insertion rates (~30% increase in prefixes/sec). With this patch and net.ipv4.fib_sync_mem set to 16MB, the same batch file runs in: $ time ./ip -batch ipv4/routes-1-hops real 0m9.692s user 0m2.491s sys 0m6.769s So the dead time is reduced to about 1/2 second or <5% of the real time. [1] 'ip' modified to not request ACK messages which improves route insertion times by about 20% Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-07net: provide a sysctl raw_l3mdev_accept for raw socket lookup with VRFsMike Manning1-0/+11
Add a sysctl raw_l3mdev_accept to control raw socket lookup in a manner similar to use of tcp_l3mdev_accept for stream and of udp_l3mdev_accept for datagram sockets. Have this default to enabled for reasons of backwards compatibility. This is so as to specify the output device with cmsg and IP_PKTINFO, but using a socket not bound to the corresponding VRF. This allows e.g. older ping implementations to be run with specifying the device but without executing it in the VRF. If the option is disabled, packets received in a VRF context are only handled by a raw socket bound to the VRF, and correspondingly packets in the default VRF are only handled by a socket not bound to any VRF. Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com> Reviewed-by: David Ahern <dsahern@gmail.com> Tested-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-26net-tcp: /proc/sys/net/ipv4/tcp_probe_interval is a u32 not intMaciej Żenczykowski1-2/+4
(fix documentation and sysctl access to treat it as such) Tested: # zcat /proc/config.gz | egrep ^CONFIG_HZ CONFIG_HZ_1000=y CONFIG_HZ=1000 # echo $[(1<<32)/1000 + 1] | tee /proc/sys/net/ipv4/tcp_probe_interval 4294968 tee: /proc/sys/net/ipv4/tcp_probe_interval: Invalid argument # echo $[(1<<32)/1000] | tee /proc/sys/net/ipv4/tcp_probe_interval 4294967 # echo 0 | tee /proc/sys/net/ipv4/tcp_probe_interval # echo -1 | tee /proc/sys/net/ipv4/tcp_probe_interval -1 tee: /proc/sys/net/ipv4/tcp_probe_interval: Invalid argument Signed-off-by: Maciej Żenczykowski <maze@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-08-01net: ipv4: Notify about changes to ip_forward_update_priorityPetr Machata1-1/+18
Drivers may make offloading decision based on whether ip_forward_update_priority is enabled or not. Therefore distribute netevent notifications to give them a chance to react to a change. Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-08-01net: ipv4: Control SKB reprioritization after forwardingPetr Machata1-0/+9
After IPv4 packets are forwarded, the priority of the corresponding SKB is updated according to the TOS field of IPv4 header. This overrides any prioritization done earlier by e.g. an skbedit action or ingress-qos-map defined at a vlan device. Such overriding may not always be desirable. Even if the packet ends up being routed, which implies this is an L3 network node, an administrator may wish to preserve whatever prioritization was done earlier on in the pipeline. Therefore introduce a sysctl that controls this behavior. Keep the default value at 1 to maintain backward-compatible behavior. Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-06ipv4: Return EINVAL when ping_group_range sysctl doesn't map to user nsTyler Hicks1-2/+3
The low and high values of the net.ipv4.ping_group_range sysctl were being silently forced to the default disabled state when a write to the sysctl contained GIDs that didn't map to the associated user namespace. Confusingly, the sysctl's write operation would return success and then a subsequent read of the sysctl would indicate that the low and high values are the overflowgid. This patch changes the behavior by clearly returning an error when the sysctl write operation receives a GID range that doesn't map to the associated user namespace. In such a situation, the previous value of the sysctl is preserved and that range will be returned in a subsequent read of the sysctl. Signed-off-by: Tyler Hicks <tyhicks@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-06-30tcp: fix Fast Open key endiannessYuchung Cheng1-5/+13
Fast Open key could be stored in different endian based on the CPU. Previously hosts in different endianness in a server farm using the same key config (sysctl value) would produce different cookies. This patch fixes it by always storing it as little endian to keep same API for LE hosts. Reported-by: Daniele Iamartino <danielei@google.com> Signed-off-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-06-04net-tcp: extend tcp_tw_reuse sysctl to enable loopback only optimizationMaciej Żenczykowski1-1/+4
This changes the /proc/sys/net/ipv4/tcp_tw_reuse from a boolean to an integer. It now takes the values 0, 1 and 2, where 0 and 1 behave as before, while 2 enables timewait socket reuse only for sockets that we can prove are loopback connections: ie. bound to 'lo' interface or where one of source or destination IPs is 127.0.0.0/8, ::ffff:127.0.0.0/104 or ::1. This enables quicker reuse of ephemeral ports for loopback connections - where tcp_tw_reuse is 100% safe from a protocol perspective (this assumes no artificially induced packet loss on 'lo'). This also makes estblishing many loopback connections *much* faster (allocating ports out of the first half of the ephemeral port range is significantly faster, then allocating from the second half) Without this change in a 32K ephemeral port space my sample program (it just establishes and closes [::1]:ephemeral -> [::1]:server_port connections in a tight loop) fails after 32765 connections in 24 seconds. With it enabled 50000 connections only take 4.7 seconds. This is particularly problematic for IPv6 where we only have one local address and cannot play tricks with varying source IP from 127.0.0.0/8 pool. Signed-off-by: Maciej Żenczykowski <maze@google.com> Cc: Neal Cardwell <ncardwell@google.com> Cc: Yuchung Cheng <ycheng@google.com> Cc: Wei Wang <weiwan@google.com> Change-Id: I0377961749979d0301b7b62871a32a4b34b654e1 Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-18tcp: add tcp_comp_sack_nr sysctlEric Dumazet1-0/+10
This per netns sysctl allows for TCP SACK compression fine-tuning. This limits number of SACK that can be compressed. Using 0 disables SACK compression. Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-18tcp: add tcp_comp_sack_delay_ns sysctlEric Dumazet1-0/+7
This per netns sysctl allows for TCP SACK compression fine-tuning. Its default value is 1,000,000, or 1 ms to meet TSO autosizing period. Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-27net: Drop pernet_operations::asyncKirill Tkhai1-1/+0
Synchronous pernet_operations are not allowed anymore. All are asynchronous. So, drop the structure member. Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-16udp: Move the udp sysctl to namespace.Tonghao Zhang1-16/+16
This patch moves the udp_rmem_min, udp_wmem_min to namespace and init the udp_l3mdev_accept explicitly. The udp_rmem_min/udp_wmem_min affect udp rx/tx queue, with this patch namespaces can set them differently. Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-04net: Rename NETEVENT_MULTIPATH_HASH_UPDATEDavid Ahern1-1/+1
Rename NETEVENT_MULTIPATH_HASH_UPDATE to NETEVENT_IPV4_MPATH_HASH_UPDATE to denote it relates to a change in the IPv4 hash policy. Signed-off-by: David Ahern <dsahern@gmail.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-13net: Convert ipv4_sysctl_opsKirill Tkhai1-0/+1
These pernet_operations create and destroy sysctl, which are not touched by anybody else. Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com> Acked-by: Andrei Vagin <avagin@virtuozzo.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-15tcp: Namespace-ify sysctl_tcp_default_congestion_controlStephen Hemminger1-8/+11
Make default TCP default congestion control to a per namespace value. This changes default congestion control to a pointer to congestion ops (rather than implicit as first element of available lsit). The congestion control setting of new namespaces is inherited from the current setting of the root namespace. Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-10tcp: Namespace-ify sysctl_tcp_rmem and sysctl_tcp_wmemEric Dumazet1-16/+16
Note that when a new netns is created, it inherits its sysctl_tcp_rmem and sysctl_tcp_wmem from initial netns. This change is needed so that we can refine TCP rcvbuf autotuning, to take RTT into consideration. Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Wei Wang <weiwan@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-04Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller1-0/+1
Files removed in 'net-next' had their license header updated in 'net'. We take the remove from 'net-next'. Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-03ipv4: Send a netevent whenever multipath hash policy is changedIdo Schimmel1-1/+19
Devices performing IPv4 forwarding need to update their multipath hash policy whenever it is changed. Inform these devices by generating a netevent. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Petr Machata <petrm@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Acked-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-02License cleanup: add SPDX GPL-2.0 license identifier to files with no licenseGreg Kroah-Hartman1-0/+1
Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-10-28tcp: Namespace-ify sysctl_tcp_pacing_ca_ratioEric Dumazet1-9/+9
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-28tcp: Namespace-ify sysctl_tcp_pacing_ss_ratioEric Dumazet1-9/+9
Also remove an obsolete comment about TCP pacing. Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-28tcp: Namespace-ify sysctl_tcp_invalid_ratelimitEric Dumazet1-7/+7
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-28tcp: Namespace-ify sysctl_tcp_autocorkingEric Dumazet1-9/+9
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-28tcp: Namespace-ify sysctl_tcp_min_rtt_wlenEric Dumazet1-7/+7
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-28tcp: Namespace-ify sysctl_tcp_min_tso_segsEric Dumazet1-9/+9
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-28tcp: Namespace-ify sysctl_tcp_challenge_ack_limitEric Dumazet1-7/+7
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-28tcp: Namespace-ify sysctl_tcp_limit_output_bytesEric Dumazet1-7/+7
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-28tcp: Namespace-ify sysctl_tcp_workaround_signed_windowsEric Dumazet1-7/+7
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-28tcp: Namespace-ify sysctl_tcp_tso_win_divisorEric Dumazet1-7/+7
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-28tcp: Namespace-ify sysctl_tcp_moderate_rcvbufEric Dumazet1-7/+7
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-28tcp: Namespace-ify sysctl_tcp_nometrics_saveEric Dumazet1-7/+7
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-27tcp: Namespace-ify sysctl_tcp_frtoEric Dumazet1-7/+7
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-27tcp: Namespace-ify sysctl_tcp_adv_win_scaleEric Dumazet1-9/+9
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-27tcp: Namespace-ify sysctl_tcp_app_winEric Dumazet1-7/+7
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-27tcp: Namespace-ify sysctl_tcp_dsackEric Dumazet1-7/+7
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-27tcp: Namespace-ify sysctl_tcp_max_reorderingEric Dumazet1-7/+7
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-27tcp: Namespace-ify sysctl_tcp_fackEric Dumazet1-7/+7
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-27tcp: Namespace-ify sysctl_tcp_abort_on_overflowEric Dumazet1-7/+7
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-27tcp: Namespace-ify sysctl_tcp_rfc1337Eric Dumazet1-7/+7
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-27tcp: Namespace-ify sysctl_tcp_stdurgEric Dumazet1-7/+7
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-27tcp: Namespace-ify sysctl_tcp_retrans_collapseEric Dumazet1-7/+7
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-27tcp: Namespace-ify sysctl_tcp_slow_start_after_idleEric Dumazet1-7/+7
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-27tcp: Namespace-ify sysctl_tcp_thin_linear_timeoutsEric Dumazet1-7/+7
Note that sysctl_tcp_thin_dupack was not used, I deleted it. Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-27tcp: Namespace-ify sysctl_tcp_recoveryEric Dumazet1-7/+7
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-27tcp: Namespace-ify sysctl_tcp_early_retransEric Dumazet1-9/+9
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-20tcp: socket option to set TCP fast open keyYuchung Cheng1-1/+2
New socket option TCP_FASTOPEN_KEY to allow different keys per listener. The listener by default uses the global key until the socket option is set. The key is a 16 bytes long binary data. This option has no effect on regular non-listener TCP sockets. Signed-off-by: Yuchung Cheng <ycheng@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Christoph Paasch <cpaasch@apple.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-01ipv4: Namespaceify tcp_fastopen_blackhole_timeout knobHaishuang Yan1-9/+11
Different namespace application might require different time period in second to disable Fastopen on active TCP sockets. Tested: Simulate following similar situation that the server's data gets dropped after 3WHS. C ---- syn-data ---> S C <--- syn/ack ----- S C ---- ack --------> S S (accept & write) C? X <- data ------ S [retry and timeout] And then print netstat of TCPFastOpenBlackhole, the counter increased as expected when the firewall blackhole issue is detected and active TFO is disabled. # cat /proc/net/netstat | awk '{print $91}' TCPFastOpenBlackhole 1 Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-01ipv4: Namespaceify tcp_fastopen_key knobHaishuang Yan1-9/+12
Different namespace application might require different tcp_fastopen_key independently of the host. David Miller pointed out there is a leak without releasing the context of tcp_fastopen_key during netns teardown. So add the release action in exit_batch path. Tested: 1. Container namespace: # cat /proc/sys/net/ipv4/tcp_fastopen_key: 2817fff2-f803cf97-eadfd1f3-78c0992b cookie key in tcp syn packets: Fast Open Cookie Kind: TCP Fast Open Cookie (34) Length: 10 Fast Open Cookie: 1e5dd82a8c492ca9 2. Host: # cat /proc/sys/net/ipv4/tcp_fastopen_key: 107d7c5f-68eb2ac7-02fb06e6-ed341702 cookie key in tcp syn packets: Fast Open Cookie Kind: TCP Fast Open Cookie (34) Length: 10 Fast Open Cookie: e213c02bf0afbc8a Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-01ipv4: Remove the 'publish' logic in tcp_fastopen_init_key_onceHaishuang Yan1-5/+0
The 'publish' logic is not necessary after commit dfea2aa65424 ("tcp: Do not call tcp_fastopen_reset_cipher from interrupt context"), because in tcp_fastopen_cookie_gen，it wouldn't call tcp_fastopen_init_key_once. Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-01ipv4: Namespaceify tcp_fastopen knobHaishuang Yan1-7/+7
Different namespace application might require enable TCP Fast Open feature independently of the host. This patch series continues making more of the TCP Fast Open related sysctl knobs be per net-namespace. Reported-by: Luca BRUNO <lucab@debian.org> Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.