| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Remove a specified DOI through the NLBL_CALIPSO_C_REMOVE command.
It requires the attribute:
NLBL_CALIPSO_A_DOI.
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
Enumerate the DOI list through the NLBL_CALIPSO_C_LISTALL command.
It takes no attributes.
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
Query a specified DOI through the NLBL_CALIPSO_C_LIST command.
It requires the attribute:
NLBL_CALIPSO_A_DOI.
The reply will contain:
NLBL_CALIPSO_A_MTYPE
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
CALIPSO is a packet labelling protocol for IPv6 which is very similar
to CIPSO. It is specified in RFC 5570. Much of the code is based on
the current CIPSO code.
This adds support for adding passthrough-type CALIPSO DOIs through the
NLBL_CALIPSO_C_ADD command. It requires attributes:
NLBL_CALIPSO_A_TYPE which must be CALIPSO_MAP_PASS.
NLBL_CALIPSO_A_DOI.
In passthrough mode the CALIPSO engine will map MLS secattr levels
and categories directly to the packet label.
At this stage, the major difference between this and the CIPSO
code is that IPv6 may be compiled as a module. To allow for
this the CALIPSO functions are registered at module init time.
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
with the commit 8c14586fc320 ("net: ipv6: Use passed in table for
nexthop lookups"), net hop lookup is first performed on route creation
in the passed-in table.
However device match is not enforced in table lookup, so the found
route can be later discarded due to egress device mismatch and no
global lookup will be performed.
This cause the following to fail:
ip link add dummy1 type dummy
ip link add dummy2 type dummy
ip link set dummy1 up
ip link set dummy2 up
ip route add 2001:db8:8086::/48 dev dummy1 metric 20
ip route add 2001:db8:d34d::/64 via 2001:db8:8086::2 dev dummy1 metric 20
ip route add 2001:db8:8086::/48 dev dummy2 metric 21
ip route add 2001:db8:d34d::/64 via 2001:db8:8086::2 dev dummy2 metric 21
RTNETLINK answers: No route to host
This change fixes the issue enforcing device lookup in
ip6_nh_lookup_table()
v1->v2: updated commit message title
Fixes: 8c14586fc320 ("net: ipv6: Use passed in table for nexthop lookups")
Reported-and-tested-by: Beniamino Galvani <bgalvani@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When receiving an ICMPv4 message containing extensions as
defined in RFC 4884, and translating it to ICMPv6 at SIT
or GRE tunnel, we need some extra manipulation in order
to properly forward the extensions.
This patch only takes care of Time Exceeded messages as they
are the ones that typically carry information from various
routers in a fabric during a traceroute session.
It also avoids complex skb logic if the data_len is not
a multiple of 8.
RFC states :
The "original datagram" field MUST contain at least 128 octets.
If the original datagram did not contain 128 octets, the
"original datagram" field MUST be zero padded to 128 octets.
In practice routers use 128 bytes of original datagram, not more.
Initial translation was added in commit ca15a078bd90
("sit: generate icmpv6 error when receiving icmpv4 error")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Oussama Ghorbel <ghorbel@pivasoftware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For better traceroute/mtr support for SIT and GRE tunnels,
we translate IPV4 ICMP ICMP_TIME_EXCEEDED to ICMPV6_TIME_EXCEED
We also have to translate the IPv4 source IP address of ICMP
message to IPv6 v4mapped.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We want to use this helper from GRE as well, so this is
the time to move it in net/ipv6/icmp.c
Also add a @nhs parameter, since SIT and GRE have different
values for the header(s) to skip.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SIT or GRE tunnels might want to translate an IPV4 address
into a v4mapped one when translating ICMP to ICMPv6.
This patch adds the parameter to icmp6_send() but
does not change icmpv6_send() signature.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPv6 version of 3f2fb9a834cb ("net: l3mdev: address selection should only
consider devices in L3 domain") and the follow up commit, a17b693cdd876
("net: l3mdev: prefer VRF master for source address selection").
That is, if outbound device is given then the address preference order
is an address from that device, an address from the master device if it
is enslaved, and then an address from a device in the same L3 domain.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPv6 source address selection needs to consider the real egress route.
Similar to IPv4 implement a get_saddr6 method which is called if
source address has not been set. The get_saddr6 method does a full
lookup which means pulling a route from the VRF FIB table and properly
considering linklocal/multicast destination addresses. Lookup failures
(eg., unreachable) then cause the source address selection to fail
which gets propagated back to the caller.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
VRF driver needs access to ip6_route_get_saddr code. Since it does
little beyond ipv6_dev_get_saddr and ipv6_dev_get_saddr is already
exported for modules move ip6_route_get_saddr to the header as an
inline.
Code move only; no functional change.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Modern C standards expect the '__inline__' keyword to come before the return
type in a declaration, and we get a couple of warnings for this with "make W=1"
in the xfrm{4,6}_policy.c files:
net/ipv6/xfrm6_policy.c:369:1: error: 'inline' is not at beginning of declaration [-Werror=old-style-declaration]
static int inline xfrm6_net_sysctl_init(struct net *net)
net/ipv6/xfrm6_policy.c:374:1: error: 'inline' is not at beginning of declaration [-Werror=old-style-declaration]
static void inline xfrm6_net_sysctl_exit(struct net *net)
net/ipv4/xfrm4_policy.c:339:1: error: 'inline' is not at beginning of declaration [-Werror=old-style-declaration]
static int inline xfrm4_net_sysctl_init(struct net *net)
net/ipv4/xfrm4_policy.c:344:1: error: 'inline' is not at beginning of declaration [-Werror=old-style-declaration]
static void inline xfrm4_net_sysctl_exit(struct net *net)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since 32b8a8e59c9c ("sit: add IPv4 over IPv4 support")
ipip6_err() may be called for packets whose IP protocol is
IPPROTO_IPIP as well as those whose IP protocol is IPPROTO_IPV6.
In the case of IPPROTO_IPIP packets the correct protocol value is not
passed to ipv4_update_pmtu() or ipv4_redirect().
This patch resolves this problem by using the IP protocol of the packet
rather than a hard-coded value. This appears to be consistent
with the usage of the protocol of a packet by icmp_socket_deliver()
the caller of ipip6_err().
I was able to exercise the redirect case by using a setup where an ICMP
redirect was received for the destination of the encapsulated packet.
However, it appears that although incorrect the protocol field is not used
in this case and thus no problem manifests. On inspection it does not
appear that a problem will manifest in the fragmentation needed/update pmtu
case either.
In short I believe this is a cosmetic fix. None the less, the use of
IPPROTO_IPV6 seems wrong and confusing.
Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1) gre_parse_header() can be called from gre_err()
At this point transport header points to ICMP header, not the inner
header.
2) We can not really change transport header as ipgre_err() will later
assume transport header still points to ICMP header (using icmp_hdr())
3) pskb_may_pull() logic in gre_parse_header() really works
if we are interested at zone pointed by skb->data
4) As Jiri explained in commit b7f8fe251e46 ("gre: do not pull header in
ICMP error processing") we should not pull headers in error handler.
So this fix :
A) changes gre_parse_header() to use skb->data instead of
skb_transport_header()
B) Adds a nhs parameter to gre_parse_header() so that we can skip the
not pulled IP header from error path.
This offset is 0 for normal receive path.
C) remove obsolete IPV6 includes
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <tom@herbertland.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The algorithm for checksum neutral mapping is incorrect. This problem
was being hidden since we were previously always performing checksum
offload on the translated addresses and only with IPv6 HW csum.
Enabling an ILA router shows the issue.
Corrected algorithm:
old_loc is the original locator in the packet, new_loc is the value
to overwrite with and is found in the lookup table. old_flag is
the old flag value (zero of CSUM_NEUTRAL_FLAG) and new_flag is
then (old_flag ^ CSUM_NEUTRAL_FLAG) & CSUM_NEUTRAL_FLAG.
Need SUM(new_id + new_flag + diff) == SUM(old_id + old_flag) for
checksum neutral translation.
Solving for diff gives:
diff = (old_id - new_id) + (old_flag - new_flag)
compute_csum_diff8(new_id, old_id) gives old_id - new_id
If old_flag is set
old_flag - new_flag = old_flag = CSUM_NEUTRAL_FLAG
Else
old_flag - new_flag = -new_flag = ~CSUM_NEUTRAL_FLAG
Tested:
- Implemented a user space program that creates random addresses
and random locators to overwrite. Compares the checksum over
the address before and after translation (must always be equal)
- Enabled ILA router and showed proper operation.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch exports some neighbour discovery functions which can be used
by 6lowpan neighbour discovery ops functionality then.
Cc: David S. Miller <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch introduces neighbour discovery ops callback structure. The
idea is to separate the handling for 6LoWPAN into the 6lowpan module.
These callback offers 6lowpan different handling, such as 802.15.4 short
address handling or RFC6775 (Neighbor Discovery Optimization for IPv6
over 6LoWPANs).
Cc: David S. Miller <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch moves the functionality to add a RA PIO prefix generated
address in an own function. This move prepares to add a hook for
adding a second address for a second link-layer address. E.g. short
address for 802.15.4 6LoWPAN.
Cc: David S. Miller <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds __ndisc_fill_addr_option as low-level function for
ndisc_fill_addr_option which doesn't depend on net_device parameter.
Cc: David S. Miller <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the autoconfiguration if a valid 802.15.4 short address
is available for 802.15.4 6LoWPAN interfaces.
Cc: David S. Miller <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPv6 multicast and link-local addresses require special handling by the
VRF driver:
1. Rather than using the VRF device index and full FIB lookups,
packets to/from these addresses should use direct FIB lookups based on
the VRF device table.
2. fail sends/receives on a VRF device to/from a multicast address
(e.g, make ping6 ff02::1%<vrf> fail)
3. move the setting of the flow oif to the first dst lookup and revert
the change in icmpv6_echo_reply made in ca254490c8dfd ("net: Add VRF
support to IPv6 stack"). Linklocal/mcast addresses require use of the
skb->dev.
With this change connections into and out of a VRF enslaved device work
for multicast and link-local addresses work (icmp, tcp, and udp)
e.g.,
1. packets into VM with VRF config:
ping6 -c3 fe80::e0:f9ff:fe1c:b974%br1
ping6 -c3 ff02::1%br1
ssh -6 fe80::e0:f9ff:fe1c:b974%br1
2. packets going out a VRF enslaved device:
ping6 -c3 fe80::18f8:83ff:fe4b:7a2e%eth1
ping6 -c3 ff02::1%eth1
ssh -6 root@fe80::18f8:83ff:fe4b:7a2e%eth1
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
L3 master devices are virtual devices similar to the loopback
device. Link local and multicast routes for these devices do
not make sense. The ipv6 addrconf code already skips adding a
linklocal address; do the same for the mcast route.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a corner case in which udp packets belonging to a same
flow are hashed to different socket when hslot->count changes from 10
to 11:
1) When hslot->count <= 10, __udp_lib_lookup() searches udp_table->hash,
and always passes 'daddr' to udp_ehashfn().
2) When hslot->count > 10, __udp_lib_lookup() searches udp_table->hash2,
but may pass 'INADDR_ANY' to udp_ehashfn() if the sockets are bound to
INADDR_ANY instead of some specific addr.
That means when hslot->count changes from 10 to 11, the hash calculated by
udp_ehashfn() is also changed, and the udp packets belonging to a same
flow will be hashed to different socket.
This is easily reproduced:
1) Create 10 udp sockets and bind all of them to 0.0.0.0:40000.
2) From the same host send udp packets to 127.0.0.1:40000, record the
socket index which receives the packets.
3) Create 1 more udp socket and bind it to 0.0.0.0:44096. The number 44096
is 40000 + UDP_HASH_SIZE(4096), this makes the new socket put into the
same hslot as the aformentioned 10 sockets, and makes the hslot->count
change from 10 to 11.
4) From the same host send udp packets to 127.0.0.1:40000, and the socket
index which receives the packets will be different from the one received
in step 2.
This should not happen as the socket bound to 0.0.0.0:44096 should not
change the behavior of the sockets bound to 0.0.0.0:40000.
It's the same case for IPv6, and this patch also fixes that.
Signed-off-by: Su, Xuemin <suxm@chinanetcenter.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cc: Tom Herbert <tom@herbertland.com>
Fixes: 4068579e1e098fa ("net: Implmement RFC 6936 (zero RX csums for UDP/IPv6")
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cc: Florent Fourcot <florent.fourcot@enst-bretagne.fr>
Fixes: 1d13a96c74fc ("ipv6: tcp: fix flowlabel value in ACK messages send from TIME_WAIT")
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPv6 ping socket error handler doesn't correctly convert the new 32 bit
mtu to host endianness before using.
Cc: Lorenzo Colitti <lorenzo@google.com>
Fixes: 6d0bfe22611602f ("net: ipv6: Add IPv6 support to the ping socket.")
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In IPv6 the ToS values are part of the flowlabel in flowi6 and get
extracted during fib rule lookup, but we forgot to correctly initialize
the flowlabel before the routing lookup.
Reported-by: <liam.mcbirnie@boeing.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
net/sched/act_police.c
net/sched/sch_drr.c
net/sched/sch_hfsc.c
net/sched/sch_prio.c
net/sched/sch_red.c
net/sched/sch_tbf.c
In net-next the drop methods of the packet schedulers got removed, so
the bug fixes to them in 'net' are irrelevant.
A packet action unload crash fix conflicts with the addition of the
new firstuse timestamp.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Frank Kellermann reported a kernel crash with 4.5.0 when IPv6 is
disabled at boot using the kernel option ipv6.disable=1. Using
current net-next with the boot option:
$ ip link add red type vrf table 1001
Generates:
[12210.919584] BUG: unable to handle kernel NULL pointer dereference at 0000000000000748
[12210.921341] IP: [<ffffffff814b30e3>] fib6_get_table+0x2c/0x5a
[12210.922537] PGD b79e3067 PUD bb32b067 PMD 0
[12210.923479] Oops: 0000 [#1] SMP
[12210.924001] Modules linked in: ipvlan 8021q garp mrp stp llc
[12210.925130] CPU: 3 PID: 1177 Comm: ip Not tainted 4.7.0-rc1+ #235
[12210.926168] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140531_083030-gandalf 04/01/2014
[12210.928065] task: ffff8800b9ac4640 ti: ffff8800bacac000 task.ti: ffff8800bacac000
[12210.929328] RIP: 0010:[<ffffffff814b30e3>] [<ffffffff814b30e3>] fib6_get_table+0x2c/0x5a
[12210.930697] RSP: 0018:ffff8800bacaf888 EFLAGS: 00010202
[12210.931563] RAX: 0000000000000748 RBX: ffffffff81a9e280 RCX: ffff8800b9ac4e28
[12210.932688] RDX: 00000000000000e9 RSI: 0000000000000002 RDI: 0000000000000286
[12210.933820] RBP: ffff8800bacaf898 R08: ffff8800b9ac4df0 R09: 000000000052001b
[12210.934941] R10: 00000000657c0000 R11: 000000000000c649 R12: 00000000000003e9
[12210.936032] R13: 00000000000003e9 R14: ffff8800bace7800 R15: ffff8800bb3ec000
[12210.937103] FS: 00007faa1766c700(0000) GS:ffff88013ac00000(0000) knlGS:0000000000000000
[12210.938321] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[12210.939166] CR2: 0000000000000748 CR3: 00000000b79d6000 CR4: 00000000000406e0
[12210.940278] Stack:
[12210.940603] ffff8800bb3ec000 ffffffff81a9e280 ffff8800bacaf8c8 ffffffff814b3135
[12210.941818] ffff8800bb3ec000 ffffffff81a9e280 ffffffff81a9e280 ffff8800bace7800
[12210.943040] ffff8800bacaf8f0 ffffffff81397c88 ffff8800bb3ec000 ffffffff81a9e280
[12210.944288] Call Trace:
[12210.944688] [<ffffffff814b3135>] fib6_new_table+0x24/0x8a
[12210.945516] [<ffffffff81397c88>] vrf_dev_init+0xd4/0x162
[12210.946328] [<ffffffff814091e1>] register_netdevice+0x100/0x396
[12210.947209] [<ffffffff8139823d>] vrf_newlink+0x40/0xb3
[12210.948001] [<ffffffff814187f0>] rtnl_newlink+0x5d3/0x6d5
...
The problem above is due to the fact that the fib hash table is not
allocated when IPv6 is disabled at boot.
As for the VRF driver it should not do any IPv6 initializations if IPv6
is disabled, so it needs to know if IPv6 is disabled at boot. The disable
parameter is private to the IPv6 module, so provide an accessor for
modules to determine if IPv6 was disabled at boot time.
Fixes: 35402e3136634 ("net: Add IPv6 support to VRF device")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ipip6_tunnel_xmit() is called immediately after checking that
skb->protocol is htons(ETH_P_IPV6) so there is no need
to check it a second time.
Found by inspection.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ip6 GRE tap device should not be forced to down state to change
the mac address and should allow live address change for tap device
similar to ipv4 gre.
Signed-off-by: Shweta Choudaha <schoudah@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ip6 GRE tap device should not be forced to down state to change
the mac address and should allow live address change for tap device
similar to ipv4 gre.
Signed-off-by: Shweta Choudaha <schoudah@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, VRFs require 1 oif and 1 iif rule per address family per
VRF. As the number of VRF devices increases it brings scalability
issues with the increasing rule list. All of the VRF rules have the
same format with the exception of the specific table id to direct the
lookup. Since the table id is available from the oif or iif in the
loopup, the VRF rules can be consolidated to a single rule that pulls
the table from the VRF device.
This patch introduces a new rule attribute l3mdev. The l3mdev rule
means the table id used for the lookup is pulled from the L3 master
device (e.g., VRF) rather than being statically defined. With the
l3mdev rule all of the basic VRF FIB rules are reduced to 1 l3mdev
rule per address family (IPv4 and IPv6).
If an admin wishes to insert higher priority rules for specific VRFs
those rules will co-exist with the l3mdev rule. This capability means
current VRF scripts will co-exist with this new simpler implementation.
Currently, the rules list for both ipv4 and ipv6 look like this:
$ ip ru ls
1000: from all oif vrf1 lookup 1001
1000: from all iif vrf1 lookup 1001
1000: from all oif vrf2 lookup 1002
1000: from all iif vrf2 lookup 1002
1000: from all oif vrf3 lookup 1003
1000: from all iif vrf3 lookup 1003
1000: from all oif vrf4 lookup 1004
1000: from all iif vrf4 lookup 1004
1000: from all oif vrf5 lookup 1005
1000: from all iif vrf5 lookup 1005
1000: from all oif vrf6 lookup 1006
1000: from all iif vrf6 lookup 1006
1000: from all oif vrf7 lookup 1007
1000: from all iif vrf7 lookup 1007
1000: from all oif vrf8 lookup 1008
1000: from all iif vrf8 lookup 1008
...
32765: from all lookup local
32766: from all lookup main
32767: from all lookup default
With the l3mdev rule the list is just the following regardless of the
number of VRFs:
$ ip ru ls
1000: from all lookup [l3mdev table]
32765: from all lookup local
32766: from all lookup main
32767: from all lookup default
(Note: the above pretty print of the rule is based on an iproute2
prototype. Actual verbage may change)
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
At present we perform an xfrm_lookup() for each UDPv6 message we
send. The lookup involves querying the flow cache (flow_cache_lookup)
and, in case of a cache miss, creating an XFRM bundle.
If we miss the flow cache, we can end up creating a new bundle and
deriving the path MTU (xfrm_init_pmtu) from on an already transformed
dst_entry, which we pass from the socket cache (sk->sk_dst_cache) down
to xfrm_lookup(). This can happen only if we're caching the dst_entry
in the socket, that is when we're using a connected UDP socket.
To put it another way, the path MTU shrinks each time we miss the flow
cache, which later on leads to incorrectly fragmented payload. It can
be observed with ESPv6 in transport mode:
1) Set up a transformation and lower the MTU to trigger fragmentation
# ip xfrm policy add dir out src ::1 dst ::1 \
tmpl src ::1 dst ::1 proto esp spi 1
# ip xfrm state add src ::1 dst ::1 \
proto esp spi 1 enc 'aes' 0x0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b
# ip link set dev lo mtu 1500
2) Monitor the packet flow and set up an UDP sink
# tcpdump -ni lo -ttt &
# socat udp6-listen:12345,fork /dev/null &
3) Send a datagram that needs fragmentation with a connected socket
# perl -e 'print "@" x 1470 | socat - udp6:[::1]:12345
2016/06/07 18:52:52 socat[724] E read(3, 0x555bb3d5ba00, 8192): Protocol error
00:00:00.000000 IP6 ::1 > ::1: frag (0|1448) ESP(spi=0x00000001,seq=0x2), length 1448
00:00:00.000014 IP6 ::1 > ::1: frag (1448|32)
00:00:00.000050 IP6 ::1 > ::1: ESP(spi=0x00000001,seq=0x3), length 1272
(^ ICMPv6 Parameter Problem)
00:00:00.000022 IP6 ::1 > ::1: ESP(spi=0x00000001,seq=0x5), length 136
4) Compare it to a non-connected socket
# perl -e 'print "@" x 1500' | socat - udp6-sendto:[::1]:12345
00:00:40.535488 IP6 ::1 > ::1: frag (0|1448) ESP(spi=0x00000001,seq=0x6), length 1448
00:00:00.000010 IP6 ::1 > ::1: frag (1448|64)
What happens in step (3) is:
1) when connecting the socket in __ip6_datagram_connect(), we
perform an XFRM lookup, miss the flow cache, create an XFRM
bundle, and cache the destination,
2) afterwards, when sending the datagram, we perform an XFRM lookup,
again, miss the flow cache (due to mismatch of flowi6_iif and
flowi6_oif, which is an issue of its own), and recreate an XFRM
bundle based on the cached (and already transformed) destination.
To prevent the recreation of an XFRM bundle, avoid an XFRM lookup
altogether whenever we already have a destination entry cached in the
socket. This prevents the path MTU shrinkage and brings us on par with
UDPv4.
The fix also benefits connected PINGv6 sockets, another user of
ip6_sk_dst_lookup_flow(), who also suffer messages being transformed
twice.
Joint work with Hannes Frederic Sowa.
Reported-by: Jan Tluka <jtluka@redhat.com>
Signed-off-by: Jakub Sitnicki <jkbs@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When setting up ILA in a router we noticed that the the encapsulation
is invoked twice: once in the route input path and again upon route
output. To resolve this we add a flag set_csum_neutral for the
ila_update_ipv6_locator. If this flag is set and the checksum
neutral bit is also set we assume that checksum-neutral translation
has already been performed and take no further action. The
flag is set only in ila_output path. The flag is not set for ila_input and
ila_xlat.
Tested:
Used 3 netns to set to emulate a router and two hosts. The router
translates SIR addresses between the two destinations in other two netns.
Verified ping and netperf are functional.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for locally originated traffic to VRF-local IPv6 addresses.
Similar to IPv4 a local dst is set on the skb and the packet is
reinserted with a call to netif_rx. With this patch, ping, tcp and udp
packets to a local IPv6 address are successfully routed:
$ ip addr show dev eth1
4: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master red state UP group default qlen 1000
link/ether 02:e0:f9:1c:b9:74 brd ff:ff:ff:ff:ff:ff
inet 10.100.1.1/24 brd 10.100.1.255 scope global eth1
valid_lft forever preferred_lft forever
inet6 2100:1::1/120 scope global
valid_lft forever preferred_lft forever
inet6 fe80::e0:f9ff:fe1c:b974/64 scope link
valid_lft forever preferred_lft forever
$ ping6 -c1 -I red 2100:1::1
ping6: Warning: source address might be selected on device other than red.
PING 2100:1::1(2100:1::1) from 2100:1::1 red: 56 data bytes
64 bytes from 2100:1::1: icmp_seq=1 ttl=64 time=0.098 ms
ip6_input is exported so the VRF driver can use it for the dst input
function. The dst_alloc function for IPv4 defaults to setting the input and
output functions; IPv6's does not. VRF does not need to duplicate the Rx path
so just export the ipv6 input function.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The v6 tcp stats scan do not provide TLP and ER timer information
correctly like the v4 version . This patch fixes that.
Fixes: 6ba8a3b19e76 ("tcp: Tail loss probe (TLP)")
Fixes: eed530b6c676 ("tcp: early retransmit")
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
skb_gso_network_seglen is not enough for checking fragment sizes if
skb is using GSO_BY_FRAGS as we have to check frag per frag.
This patch introduces skb_gso_validate_mtu, based on the former, which
will wrap the use case inside it as all calls to skb_gso_network_seglen
were to validate if it fits on a given TMU, and improve the check.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Tested-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Paul Moore tracked a regression caused by a recent commit, which
mistakenly assumed that sk_filter() could be avoided if socket
had no current BPF filter.
The intent was to avoid udp_lib_checksum_complete() overhead.
But sk_filter() also checks skb_pfmemalloc() and
security_sock_rcv_skb(), so better call it.
Fixes: e6afc8ace6dd ("udp: remove headers from UDP packets before queueing")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Paul Moore <paul@paul-moore.com>
Tested-by: Paul Moore <paul@paul-moore.com>
Tested-by: Stephen Smalley <sds@tycho.nsa.gov>
Cc: samanthakumar <samanthakumar@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for your net tree,
they are:
1) Fix incorrect timestamp in nfnetlink_queue introduced when addressing
y2038 safe timestamp, from Florian Westphal.
2) Get rid of leftover conntrack definition from the previous merge
window, oneliner from Florian.
3) Make nf_queue handler pernet to resolve race on dereferencing the
hook state structure with netns removal, from Eric Biederman.
4) Ensure clean exit on unregistered helper ports, from Taehee Yoo.
5) Restore FLOWI_FLAG_KNOWN_NH in nf_dup_ipv6. This got lost while
generalizing xt_TEE to add packet duplication support in nf_tables,
from Paolo Abeni.
6) Insufficient netlink NFTA_SET_TABLE attribute check in
nf_tables_getset(), from Phil Turnbull.
7) Reject helper registration on duplicated ports via modparams.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Kconfig options I added to work around broken compilation ended
up screwing up things more, as I used the wrong symbol to control
compilation of the file, resulting in IPv6 fou support to never be built
into the kernel.
Changing CONFIG_NET_FOU_IPV6_TUNNELS to CONFIG_IPV6_FOU fixes that
problem, I had renamed the symbol in one location but not the other,
and as the file is never being used by other kernel code, this did not
lead to a build failure that I would have caught.
After that fix, another issue with the same patch becomes obvious, as we
'select INET6_TUNNEL', which is related to IPV6_TUNNEL, but not the same,
and this can still cause the original build failure when IPV6_TUNNEL is
not built-in but IPV6_FOU is. The fix is equally trivial, we just need
to select the right symbol.
I have successfully build 350 randconfig kernels with this patch
and verified that the driver is now being built.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Valentin Rothberg <valentinrothberg@gmail.com>
Fixes: fabb13db448e ("fou: add Kconfig options for IPv6 support")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With the commit 48e8aa6e3137 ("ipv6: Set FLOWI_FLAG_KNOWN_NH at
flowi6_flags") ip6_pol_route() callers were asked to to set the
FLOWI_FLAG_KNOWN_NH properly and xt_TEE was updated accordingly,
but with the later refactor in commit bbde9fc1824a ("netfilter:
factor out packet duplication for IPv4/IPv6") the flowi6_flags
update was lost.
This commit re-add it just before the routing decision.
Fixes: bbde9fc1824a ("netfilter: factor out packet duplication for IPv4/IPv6")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
A previous patch added the fou6.ko module, but that failed to link
in a couple of configurations:
net/built-in.o: In function `ip6_tnl_encap_add_fou_ops':
net/ipv6/fou6.c:88: undefined reference to `ip6_tnl_encap_add_ops'
net/ipv6/fou6.c:94: undefined reference to `ip6_tnl_encap_add_ops'
net/ipv6/fou6.c:97: undefined reference to `ip6_tnl_encap_del_ops'
net/built-in.o: In function `ip6_tnl_encap_del_fou_ops':
net/ipv6/fou6.c:106: undefined reference to `ip6_tnl_encap_del_ops'
net/ipv6/fou6.c:107: undefined reference to `ip6_tnl_encap_del_ops'
If CONFIG_IPV6=m, ip6_tnl_encap_add_ops/ip6_tnl_encap_del_ops
are in a module, but fou6.c can still be built-in, and that
obviously fails to link.
Also, if CONFIG_IPV6=y, but CONFIG_IPV6_TUNNEL=m or
CONFIG_IPV6_TUNNEL=n, the same problem happens for a different
reason.
This adds two new silent Kconfig symbols to work around both
problems:
- CONFIG_IPV6_FOU is now always set to 'm' if either CONFIG_NET_FOU=m
or CONFIG_IPV6=m
- CONFIG_IPV6_FOU_TUNNEL is set implicitly when IPV6_FOU is enabled
and NET_FOU_IP_TUNNELS is also turned out, and it will ensure
that CONFIG_IPV6_TUNNEL is also available.
The options could be made user-visible as well, to give additional
room for configuration, but it seems easier not to bother users
with more choice here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: aa3463d65e7b ("fou: Add encap ops for IPv6 tunnels")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In gre6 xmit path, we are sending a GRE packet, so set fl6 proto
to IPPROTO_GRE properly.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When creat an ip6gretap interface with an unreachable route,
the MTU is about 14 bytes larger than what was needed.
If the remote address is reachable:
ping6 2001:0:130::1 -c 2
PING 2001:0:130::1(2001:0:130::1) 56 data bytes
64 bytes from 2001:0:130::1: icmp_seq=1 ttl=64 time=1.46 ms
64 bytes from 2001:0:130::1: icmp_seq=2 ttl=64 time=81.1 ms
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case we find a socket with encapsulation enabled we should call
the encap_recv function even if just a udp header without payload is
available. The callbacks are responsible for correctly verifying and
dropping the packets.
Also, in case the header validation fails for geneve and vxlan we
shouldn't put the skb back into the socket queue, no one will pick
them up there. Instead we can simply discard them in the respective
encap_recv functions.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch addresses the same issue we had for IPv4 where enabling GRE with
an inner checksum cannot be supported with FOU/GUE due to the fact that
they will jump past the GRE header at it is treated like a tunnel header.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since iptunnel_handle_offloads() is called in all paths we can
probably drop the block in ip6_tnl_xmit that was checking for
skb->encapsulation and resetting the inner headers.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Huw Davies
Paolo Abeni
Eric Dumazet
David Ahern
Arnd Bergmann
Simon Horman
Tom Herbert
Alexander Aring
Su, Xuemin
Hannes Frederic Sowa
David S. Miller
Shweta Choudaha
Jakub Sitnicki
Yuchung Cheng
Marcelo Ricardo Leitner
Haishuang Yan
Alexander Duyck