| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Add the following to support beacon report radio measurement
with the measurement mode field set to passive or active:
1. Propagate the required scan duration to the device
2. Report the scan start time (in terms of TSF)
3. Report each BSS's detection time (also in terms of TSF)
TSF times refer to the BSS that the interface that requested the
scan is connected to.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
[changed ath9k/10k, at76c59x-usb, iwlegacy, wl1251 and wlcore to match
the new API]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There is no other limit other than a global
packet count limit when using software queuing.
This means a single flow queue can grow insanely
long. This is particularly bad for TCP congestion
algorithms which requires a little more
sophisticated frame dropping scheme than a mere
headdrop on limit overflow.
Hence apply (a slighly modified, to fit the knobs)
CoDel5 on flow queues. This improves TCP
convergence and stability when combined with
wireless driver which keeps its own tx queue/fifo
at a minimum fill level for given link conditions.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
mac80211's software queues were designed to work
very closely with device tx queues. They are
required to make use of 802.11 packet aggregation
easily and efficiently.
Due to the way 802.11 aggregation is designed it
only makes sense to keep fair queuing as close to
hardware as possible to reduce induced latency and
inertia and provide the best flow responsiveness.
This change doesn't translate directly to
immediate and significant gains. End result
depends on driver's induced latency. Best results
can be achieved if driver keeps its own tx
queue/fifo fill level to a minimum.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Qdiscs are designed with no regard to 802.11
aggregation requirements and hand out
packet-by-packet with no guarantee they are
destined to the same tid. This does more bad than
good no matter how fairly a given qdisc may behave
on an ethernet interface.
Software queuing used per-AC netdev subqueue
congestion control whenever a global AC limit was
hit. This meant in practice a single station or
tid queue could starve others rather easily. This
could resonate with qdiscs in a bad way or could
just end up with poor aggregation performance.
Increasing the AC limit would increase induced
latency which is also bad.
Disabling qdiscs by default and performing
taildrop instead of netdev subqueue congestion
control on the other hand makes it possible for
tid queues to fill up "in the meantime" while
preventing stations starving each other.
This increases aggregation opportunities and
should allow software queuing based drivers
achieve better performance by utilizing airtime
more efficiently with big aggregates.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This enum is already perfectly aliased to enum nl80211_band, and
the only reason for it is that we get IEEE80211_NUM_BANDS out of
it. There's no really good reason to not declare the number of
bands in nl80211 though, so do that and remove the cfg80211 one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
|
|
Requires software tx queueing and fast-xmit support. For good
performance, drivers need frag_list support as well. This avoids the
need for copying data of aggregated frames. Running without it is only
supported for debugging purposes.
To avoid performance and packet size issues, the rate control module or
driver needs to limit the maximum A-MSDU size by setting
max_rc_amsdu_len in struct ieee80211_sta.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[fix locking issue]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The regular RX path has a lot of code, but with a few
assumptions on the hardware it's possible to reduce the
amount of code significantly. Currently the assumptions
on the driver are the following:
* hardware/driver reordering buffer (if supporting aggregation)
* hardware/driver decryption & PN checking (if using encryption)
* hardware/driver did de-duplication
* hardware/driver did A-MSDU deaggregation
* AP_LINK_PS is used (in AP mode)
* no client powersave handling in mac80211 (in client mode)
of which some are actually checked per packet:
* de-duplication
* PN checking
* decryption
and additionally packets must
* not be A-MSDU (have been deaggregated by driver/device)
* be data packets
* not be fragmented
* be unicast
* have RFC 1042 header
Additionally dynamically we assume:
* no encryption or CCMP/GCMP, TKIP/WEP/other not allowed
* station must be authorized
* 4-addr format not enabled
Some data needed for the RX path is cached in a new per-station
"fast_rx" structure, so that we only need to look at this and
the packet, no other memory when processing packets on the fast
RX path.
After doing the above per-packet checks, the data path collapses
down to a pretty simple conversion function taking advantage of
the data cached in the small fast_rx struct.
This should speed up the RX processing, and will make it easier
to reason about parallelizing RX (for which statistics will need
to be per-CPU still.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In the time since the mesh path table was implemented as an
RCU-traversable, dynamically growing hash table, a generic RCU
hashtable implementation was added to the kernel.
Switch the mesh path table over to rhashtable to remove some code
and also gain some features like automatic shrinking.
Cc: Thomas Graf <tgraf@suug.ch>
Cc: netdev@vger.kernel.org
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The mesh path and mesh gate hashtables are global, containing
all of the mpaths for every mesh interface, but the paths are
all tied logically to a single interface. The common case is
just a single mesh interface, so optimize for that by moving
the global hashtable into the per-interface struct.
Doing so allows us to drop sdata pointer comparisons inside
the lookups and also saves a few bytes of BSS and data.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The previous approach simply ignored chandef restrictions when calculating
the appropriate peer BW for a WIDER_BW peer. This could result in a
regulatory violation if both peers indicated 80MHz support, but the
regdomain forbade it.
Change the approach to setting a WIDER_BW peer's BW. Don't exempt it from
the chandef width at first. If during TDLS negotiation the chandef width
is upgraded, update the peer's BW to match.
Fixes: 0fabfaafec3a ("mac80211: upgrade BW of TDLS peers when possible")
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Several cases of overlapping changes, as well as one instance
(vxlan) of a bug fix in 'net' overlapping with code movement
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Just like for CCMP we need to check that for GCMP the fragments
have PNs that increment by one; the spec was updated to fix this
security issue and now has the following text:
The receiver shall discard MSDUs and MMPDUs whose constituent
MPDU PN values are not incrementing in steps of 1.
Adapt the code for CCMP to work for GCMP as well, luckily the
relevant fields already alias each other so no code duplication
is needed (just check the aliasing with BUILD_BUG_ON.)
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Drivers may need to track which vif is using VHT MU-MIMO.
Move the flag indicationg the ownership of MU_MIMO to
ieee80211_vif.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Clean up ieee80211_rx_reorder_ready() callers by passing the RX
TID struct and the index, instead of the frames list. This will
make it more extensible as well.
While at it, move the inline to rx.c as it's only used there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This will allow drivers to make more educated
decisions whether to defer transmission or not.
Relying on wake_tx_queue() call count implicitly
was not possible because it could be called
without queued frame count actually changing on
software tx aggregation start/stop code paths.
It was also not possible to know how long
byte-wise queue was without dequeueing.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The timestamp given by iwlwifi is at the beginning of the
frame over the air, at (or during) the SYNC field. Allow
such timestamps to be given to mac80211, at least (for now)
for frames with non-HT/VHT preambles.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The station MLME and IBSS/mesh ones use entirely different
code for interpreting HT and VHT operation elements. Change
the code that interprets them a bit - it now modifies an
existing chandef - and use it also in the MLME code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The Group ID Management frame is an Action frame of
category VHT. It is transmitted by the AP to assign
or change the user position of a STA for one or more
group IDs.
Process and save the group membership data. Notify
underlying driver of changes.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Conflicts:
drivers/net/geneve.c
Here we had an overlapping change, where in 'net' the extraneous stats
bump was being removed whilst in 'net-next' the final argument to
udp_tunnel6_xmit_skb() was being changed.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
An AP can send an operating channel width change in a beacon
opmode notification IE as long as there's a change in the nss as
well (See 802.11ac-2013 section 10.41).
So don't limit updating to nss only from an opmode notification IE.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Jouni found a bug in the remain-on-channel logic: when a short item
is queued, a long item is combined with it extending the original
one, and then the long item is deleted, the timeout doesn't go back
to the short one, and the short item ends up taking a long time. In
this case, this showed as blocking scan when running two test cases
back to back - the scan from the second was delayed even though all
the remain-on-channel items should long have been gone.
Fixing this with the current data structures turns out to be a bit
complicated, we just remove the long item from the dependents list
right now and don't recalculate the timeouts.
There's a somewhat similar bug where we delete the short item and
all the dependents go with it; to fix this we'd have to move them
from the dependents to the real list.
Instead of trying to do that, rewrite the code to not have all this
complexity in the data structures: use a single list and allow more
than one entry in it being marked as started. This makes the code a
bit more complex, the worker needs to understand that it might need
to just remove one of the started items, while keeping the device
off-channel, but that's not more complicated than the nested data
structures.
This then fixes both issues described, and makes it easier to also
limit the overall off-channel time when combining.
TODO: as before, with hardware remain-on-channel, deleting an item
after combining results in cancelling them all - we can keep track
of the time elapsed and only cancel after that to fix this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Since the cookie is assigned inside ieee80211_make_ack_skb()
now, we no longer need to return the ack_skb as the cookie
and can simplify the function's return and the callers. Also
rename it to ieee80211_attach_ack_skb() to more accurately
reflect its purpose.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This is quite a bit of code that logically depends here since
it has to deal with all the remain-on-channel logic.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The function currently determines this value, for use in bss_info.qos,
based on the interface type itself. Make it a parameter instead and
set it with the same logic for now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When 11n peers performs a TDLS connection on a legacy BSS, the HT
operation IE must be specified according to IEEE802.11-2012 section
9.23.3.2. Otherwise HT-protection is compromised and the medium becomes
noisy for both the TDLS and the BSS links.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Scheduled scan has to be reconfigured only if wowlan wasn't
configured, since otherwise it should continue to run (with
the 'any' trigger) or be aborted.
The current code will end up asking the driver to start a new
scheduled scan without stopping the previous one, and leaking
some memory (from the previous request.)
Fix this by doing the abort/restart under the proper conditions.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There's little point in keeping (and even sending to userspace)
the beacon_loss_count value per station, since it can only apply
to the AP on a managed-mode connection. Move the value to ifmgd,
advertise it only in managed mode, and remove it from ethtool as
it's available through better interfaces.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
That file contains just a single function, which itself is just a
single statement to call a different function. Remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The file contains just a single declaration that can easily
move to another file - remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
As this API has never really seen any use and most drivers don't
ever use the value derived from it, remove it.
Change the only driver using it (rt2x00) to simply use the DTIM
period instead of the "max sleep" time.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Instead of int with 0/1, use bool with false/true for the
powersave argument to ieee80211_send_nullfunc().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This allows ieee80211_tx_monitor to be used directly for sending 802.11 frames
to all monitor interfaces.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
It doesn't seem problematic to change the weight for the average
beacon signal from 3 to 4, so use DECLARE_EWMA. This also makes
the code easier to maintain since bugs like the one fixed in the
previous patch can't happen as easily.
With a fix from Avraham Stern to invert the sign since EMWA uses
unsigned values only.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
These file aren't really useful:
- if per beacon data is required then you need to use
radiotap or similar anyway, debugfs won't help much
- average beacon signal is reported in station info in
nl80211 and can be looked up with iw
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Sometimes we are interested in testing TDLS performance in a specific
width setting. Add the ability to disable the wider-band feature, thereby
allowing the TDLS channel width to be controlled by the BSS width.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Define rc_rateidx_vht_mcs_mask array and rate_idx_match_vht_mcs_mask()
method in order to apply mcs mask for vht rates
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Move TDLS channel-switch Rx handling into an RTNL locked work. This is
required to add proper regulatory checking to incoming channel-switch
requests.
Queue incoming requests in a dedicated skb queue and handle the request
in a device-specific work to avoid deadlocking on interface removal.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add support for declaring MU-MIMO beamformee capability for
relevant hardware.
When sending association request, the capability is included if both
hardware and the AP support it, and no other virtual interface
is using it.
This is in order to avoid multiple interfaces using MU-MIMO in parallel
which might lead to contradictions in the group-id mechanism.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Most of the fields in this struct use too wide types, change
that to shrink the struct from 64 to 48 bytes (on 64-bit.)
This results in a total saving of 64 bytes for each interface.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The IEEE802.11-2012 specification is vague regarding SMPS operation during
TDLS. It does not define a clear way to transition between SMPS states.
To avoid interop issues, set SMPS to off when TDLS peers are connected.
Accomplish this by extending the definition of the AUTOMATIC state. If the
driver forces a state other than OFF, disconnect all TDLS peers.
While at it, avoid changing the SMPS state of the peer STA. We have no
way to control it, so try and behave correctly towards it.
Move the TDLS peer-teardown function to where the rest of the TDLS code
resides.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Define a station chandef, to be used for wider-bw TDLS peers. When both
peers support the feature, upgrade the channel bandwidth to the maximum
allowed by both peers and regulatory. Currently widths up to 80MHz are
supported in the 5GHz band.
When a TDLS peer connects/disconnects recalculate the channel type of the
current chanctx.
Make the chanctx width calculation consider wider-bw TDLS peers and
similarly fix the max_required_bw calculation for the chanctx min_def.
Since the sta->bandwidth is calculated only later on, take
bss_conf.chandef.width as the minimal width for station interface.
Set the upgraded channel width in the VHT-operation set during TDLS setup.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There's a long-standing TODO item to use this flag in the cooked
monitor RX, but clearly it was never needed and now this hasn't
been used by userspace for a long time, so no userspace changes
could require it now.
Remove the unused flag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When introducing multiple RX queues, a single NAPI struct will not
be sufficient. Instead of trying to store multiple, simply change
the API to have the NAPI struct passed to the RX function. This of
course means that drivers using rx_irqsafe() cannot use NAPI, but
that seems a reasonable trade-off, particularly since only two of
all drivers are currently using it at all.
While at it, we can now remove the IEEE80211_RX_REORDER_TIMER flag
again since this code path cannot have a napi struct anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This function is only used in the RX code, so moving it into
that file gives the compiler better optimisation possibilities
and also allows us to remove the check for short frames (which
in the RX path cannot happen, but as a generic utility needed
to be checked.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Short frames less than 16 octets are already blocked in the monitor
code by the should_drop_frame() function, and cannot get into the
regular RX path. Therefore, this check can never trigger and the
counter invariably stays zero. Remove the useless code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Conflicts:
drivers/net/phy/amd-xgbe-phy.c
drivers/net/wireless/iwlwifi/Kconfig
include/net/mac80211.h
iwlwifi/Kconfig and mac80211.h were both trivial overlapping
changes.
The drivers/net/phy/amd-xgbe-phy.c file got removed in 'net-next' and
the bug fix that happened on the 'net' side is already integrated
into the rest of the amd-xgbe driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Due to remain-on-channel scheduling delays, when we split an ROC
while coalescing, we'll usually get a picture like this:
existing ROC: |------------------|
current time: ^
new ROC: |------| |-------|
If the expected response frames are then transmitted by the peer
in the hole between the two fragments of the new ROC, we miss
them and the process (e.g. ANQP query) fails.
mac80211 expects that the window to miss something is small:
existing ROC: |------------------|
new ROC: |------||-------|
but that's normally not the case.
To avoid this problem, coalesce only if the new ROC's duration
is <= the remaining time on the existing one:
existing ROC: |------------------|
new ROC: |-----|
and never split a new one but schedule it afterwards instead:
existing ROC: |------------------|
new ROC: |-------------|
type=bugfix
bug=not-tracked
fixes=unknown
Reported-by: Matti Gottlieb <matti.gottlieb@intel.com>
Reviewed-by: EliadX Peller <eliad@wizery.com>
Reviewed-by: Matti Gottlieb <matti.gottlieb@intel.com>
Tested-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
No matter how the driver manages its NAPI context, there's no way
sending frames to it from a timer can be correct, since it would
corrupt the internal GRO lists.
To avoid that, always use the non-NAPI path when releasing frames
from the timer.
Cc: stable@vger.kernel.org
Reported-by: Jean Trivelly <jean.trivelly@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
As I was testing with hwsim, I missed that my previous commit to
make LED work depend on activation broke the code because I missed
removing the old trigger struct and some code was still using it,
now erroneously, causing crashes.
Fix this by always using the correct struct.
Reported-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
Avraham Stern
Michal Kazior
Johannes Berg
David S. Miller
Felix Fietkau
Bob Copeland
Arik Nemtsov
Sara Sharon
Eyal Shapira
Eliad Peller
Helmut Schaa
Lorenzo Bianconi