aboutsummaryrefslogtreecommitdiffstats
path: root/net/mac80211/mesh.h (follow)
AgeCommit message (Collapse)AuthorFilesLines
2012-06-18{nl,cfg,mac}80211: implement dot11MeshHWMPconfirmationIntervalChun-Yeow Yeoh1-0/+2
As defined in section 13.10.9.3 Case D (802.11-2012), this control variable is used to limit the mesh STA to send only one PREQ to a root mesh STA within this interval of time (in TUs). The default value for this variable is set to 2000 TUs. However, for current implementation, the maximum configurable of dot11MeshHWMPconfirmationInterval is restricted by dot11MeshHWMPactivePathTimeout. Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com> [line-break commit log] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-06-09mac80211: Rename stainfo variable for the more common staJavier Cardona1-1/+1
Signed-off-by: Javier Cardona <javier@cozybit.com> Reviewed-by: Jason Abele <jason@cozybit.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-04-24mac80211: Adds clean sdata helperAndrei Emeltchenko1-1/+3
Adds hepler to clean sdata ieee80211_clean_sdata similar way as ieee80211_setup_sdata is implemented. The function will be used by other interfaces later. Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23mac80211: refactor mesh peer rate handlingThomas Pedersen1-5/+5
To avoid passing supp_rates and basic_rates around all the time, just derive these when needed in mesh_matches_local() and mesh_peer_init(). Signed-off-by: Thomas Pedersen <thomas@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-11mac80211: Check basic rates when peeringAshok Nagarajan1-1/+1
Section 13.2.3 of IEEE 80211s standard requires BSSBasicRateSet of mesh nodes to be identical to establish peer link. Signed-off-by: Ashok Nagarajan <ashok@cozybit.com> Signed-off-by: Thomas Pedersen <thomas@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-10mac80211: Implement mesh synchronization frameworkJavier Cardona1-0/+19
This patch adds MBSS extensible synchronization framework (Sec. 13.13.2 of IEEE Std. 802.11-2012). The framework is implemented via an ops table which defines the following functions: rx_bcn_presp() - this is called every time a mesh beacon is received. adjust_tbtt() - this is called immediately before a beacon is about to be transmitted. The default neighbor offset synchronization defined in the standard is implemented. We also provide template functions for vendor specific methods. When neighbor offset synchronization is active (which is the default) mesh neighbors in the same MBSS will track timing offsets to each other and compensate clock drift. In our tests we observed that this mesh synchronization implementation successfully corrected drifts between stations of ~2PPM while introducing a jitter of ~20us. It is also possible to test this framework on mac80211_hwsim simulated phys to see how it behaves under different topologies, over poor links, etc. Signed-off-by: Marco Porsch <marco.porsch@s2005.tu-chemnitz.de> Signed-off-by: Pavel Zubarev <pavel.zubarev@gmail.com> Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-09mac80211: fix the RANN propagation issuesChun-Yeow Yeoh1-0/+2
This patch is intended to solve the follwing issues in RANN propagation: [1] The interval in propagated RANN should be based on the interval of received RANN. [2] The aggregated path metric for propagated RANN is as received plus own link metric towards the transmitting mesh STA (not root mesh STA). [3] The comparison of path metric for RANN with same sequence number should be done before deciding whether to propagate or not. Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-09wireless: rename ht_info to ht_operationJohannes Berg1-1/+1
Since some of the HT code pre-dates 802.11n-2009 some names are wrong. The one that bothers me most is that "HT operation" is called "HT information" in our code and that causes confusion. Rename "HT information" to "HT operation" and also the control_chan field to primary_chan to match the name used in the spec. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Acked-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-05mac80211: Fix the generation of PREQs in proactive RANN mechanism of HWMPChun-Yeow Yeoh1-0/+4
According to Section Y.7.4 Actions on receipt of proactive RANN, an individually addressed PREQ should be generated towards the neighbor peer mesh STA indicated in the RANN Sender Address field in the forwarding information. Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com> Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: Thomas Pedersen <thomas@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-27mac80211: clean up asm/unaligned.h inclusionJohannes Berg1-1/+0
Some files implicitly get this via mesh.h which itself doesn't need it, so move the inclusion into the right files. Some other files don't need it at all but include it, so remove it from there. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-28mac80211: don't initiate path discovery when forwarding frame with unknown DAThomas Pedersen1-0/+2
We used to initiate a path discovery when receiving a frame for which there is no forwarding information. To cut down on PREQ spam, just send a (gated) PERR in response. Also separate path discovery logic from nexthop querying. This patch means we no longer queue frames when forwarding, so kill the PERR TX stuff in discard_frame(). Signed-off-by: Thomas Pedersen <thomas@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-09mac80211: Avoid filling up mesh preq queue with redundant requestsJavier Cardona1-0/+3
Don't accept redundant PREQs for a given destination. This fixes a problem under high load: kernel: [20386.250913] mesh_queue_preq: 235 callbacks suppressed kernel: [20386.253335] Mesh HWMP (mesh0): PREQ node queue full kernel: [20386.253352] Mesh HWMP (mesh0): PREQ node queue full (...) The 802.11s protocol has a provision to limit the rate of path requests (PREQs) are transmitted (dot11MeshHWMPpreqMinInterval) but there was no limit on the rate at which PREQs were being queued up. There is a valid reason for queuing PREQs: this way we can even out PREQ bursts. But queueing multiple PREQs for the same destination is useless. Reported-by: Pedro Larbig <pedro.larbig@carhs.de> Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-08mac80211: add HT IEs to mesh framesThomas Pedersen1-0/+4
Signed-off-by: Thomas Pedersen <thomas@cozybit.com> Signed-off-by: Ashok Nagarajan <anagar6@uic.edu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-30mac80211: standardize adding supported rates IEsArik Nemtsov1-4/+0
Relocate the mesh implementation of adding the (extended) supported rates IE to util.c, anticipating its use by other parts of mac80211. Signed-off-by: Arik Nemtsov <arik@wizery.com> Cc: Kalyan C Gaddam <chakkal@iit.edu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-13mac80211: Improve mpath state lockingJavier Cardona1-1/+3
No need to take the mpath state lock when an mpath is removed. Also, no need checking the lock when reading mpath flags. Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-13mac80211: Remove mesh paths when an interface is removedJavier Cardona1-1/+1
When an interface is removed, the mesh paths associated with it should also be removed. This fixes a bug we observed when reloading a device driver module without reloading mac80211s. Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-24{nl,cfg,mac}80211: let userspace set RANN intervalJavier Cardona1-1/+0
Allow userspace to set Root Announcement Interval for our mesh interface. Also, RANN interval is now in proper units of TUs. Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-24mac80211: mesh gate implementationJavier Cardona1-0/+11
In this implementation, a mesh gate is a root node with a certain bit set in its RANN flags. The mpath to this root node is marked as a path to a gate, and added to our list of known gates for this if_mesh. Once a path discovery process fails, we forward the unresolved frames to a known gate. Thanks to Luis Rodriguez for refactoring and bug fix help. Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-22mac80211: update mesh path selection frame formatThomas Pedersen1-8/+4
Make mesh path selection frames Mesh Action category, remove outdated Mesh Path Selection category and defines, use updated reason codes, add mesh_action_is_path_sel for readability, and update/correct path selection IEs. Signed-off-by: Thomas Pedersen <thomas@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-22mac80211: fix mesh beacon formatThomas Pedersen1-0/+14
Correct ordering of IEs in the mesh beacon while removing unneeded IEs from mesh peering frames. Set privacy bit in capability info if security is enabled. Add utility functions to aid in construction of IEs and reduce code duplication. Signed-off-by: Thomas Pedersen <thomas@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-16mac80211: annotate and fix RCU in mesh codeJohannes Berg1-4/+0
This adds proper RCU annotations to the mesh path table code, and fixes a number of bugs in the code that I found while checking the sparse warnings I got as a result of the annotations. Some things like the changes in mesh_path_add() or mesh_pathtbl_init() only serve to shut up sparse, but other changes like the changes surrounding the for_each_mesh_entry() macro fix real RCU bugs in the code. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-16mac80211: fix and simplify mesh lockingJohannes Berg1-0/+3
The locking in mesh_{mpath,mpp}_table_grow not only has an rcu_read_unlock() missing, it's also racy (though really only technically since it's invoked from a single function only) since it obtains the new size of the table without any locking, so two invocations of the function could attempt the same resize. Additionally, it uses synchronize_rcu() which is rather expensive and can be avoided trivially here. Modify the functions to only use the table lock and use call_rcu() instead of synchronize_rcu(). Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-16mac80211: sparse RCU annotationsJohannes Berg1-1/+1
This adds sparse RCU annotations to most of mac80211, only the mesh code remains to be done. Due the the previous patches, the annotations are pretty simple. The only thing that this actually changes is removing the RCU usage of key->sta in debugfs since this pointer isn't actually an RCU-managed pointer (it only has a single assignment done before the key even goes live). As that is otherwise harmless, I decided to make it part of this patch. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-12mac80211: mesh: move some code to make it staticJohannes Berg1-4/+0
There's no need to have table functions in one file and all users in another, move the functions to the right file and make them static. Also move a static variable to the beginning of the file to make it easier to find. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-12mac80211: send notification on new peer candidate for our secure meshJavier Cardona1-1/+2
Also, advertise support for mesh authentication. Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-20mac80211: Remove unused third address from mesh address extension header.Javier Cardona1-2/+2
The Mesh Control header only includes 0, 1 or 2 addresses. If there is one address, it should be interpreted as Address 4. If there are 2, they are interpreted as Addresses 5 and 6 (Address 4 being the 4th address in the 802.11 header). The address extension used to hold up to 3 addresses instead of the current 2. I'm not sure which draft version changed this, but it is very unlikely that it will change again given the state of the approval process of this draft. See section 7.1.3.6.3 in current draft (8.0). Also, note that the extra address that I'm removing was not being used, so this change has no effect on over-the-air frame formats. But I thought I better remove it before someone does start using it. Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-20mac80211: Send mesh non-HWMP path selection frames to userspaceJavier Cardona1-0/+7
Let path selection frames for protocols other than HWMP be sent to userspace via NL80211_CMD_REGISTER_FRAME. Also allow userspace to send and receive mesh path selection frames. Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-15wireless:mac80211: kill unuse macro MESH_CFG_CMP_LEN in mesh.hShan Wei1-11/+0
Commit 00d3f14c has removed the references of this macro, but left it only. So remove this definition. commit 00d3f14cf9f12c21428121026a5e1d5f65926447 Author: Johannes Berg <johannes@sipsolutions.net> Date: Tue Feb 10 21:26:00 2009 +0100 mac80211: use cfg80211s BSS infrastructure Remove all the code from mac80211 to keep track of BSSes and use the cfg80211-provided code completely. Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-06cfg80211/mac80211: add mesh join/leave commandsJohannes Berg1-25/+0
Instead of tying mesh activity to interface up, add join and leave commands for mesh. Since we must be backward compatible, let cfg80211 handle joining a mesh if a mesh ID was pre-configured when the device goes up. Note that this therefore must modify mac80211 as well since mac80211 needs to lose the logic to start the mesh on interface up. We now allow querying mesh parameters before the mesh is connected, which simply returns defaults. Setting them (internally renamed to "update") is only allowed while connected. Specify them with the new mesh join command instead where needed. In mac80211, beaconing must now also follow the mesh enabled/not enabled state, which is done by testing the mesh ID. Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-06nl80211/mac80211: define and allow configuring mesh element TTLJavier Cardona1-0/+2
The TTL in path selection information elements is different from the mesh ttl used in mesh data frames. Version 7.03 of the 11s draft calls this ttl 'Element TTL'. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-09Fix spelling fuction -> function in commentsStefan Weil1-1/+1
To avoid more patches, I also fixed other spelling and grammar bugs when they were in the same or following line: successfull -> successful parse -> parses controler -> controller controlers -> controllers Cc: Jiri Kosina <trivial@kernel.org> Cc: linux-kernel@vger.kernel.org Signed-off-by: Stefan Weil <weil@mail.berlios.de> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2010-06-14mac80211: pull mgmt frame rx into rx handlerJohannes Berg1-2/+0
Some code is duplicated between ibss, mesh and managed mode regarding the queueing of management frames. Since all modes now use a common skb queue and a common work function, we can pull the queueing code into the rx handler directly and remove the duplicated length checks etc. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-08mac80211: Moved mesh action codes to a more visible locationJavier Cardona1-2/+0
Grouped mesh action codes together with the other action codes in ieee80211.h. Signed-off-by: Javier Cardona <javier@cozybit.com> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-10mac80211: Revert 'Use correct sign for mesh active path refresh'Javier Cardona1-2/+3
The patch ("mac80211: Use correct sign for mesh active path refresh.") was actually a bug. Reverted it and improved the explanation of how mesh path refresh works. Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: Andrey Yurovsky <andrey@cozybit.com> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-18mac80211: use fixed broadcast addressJohannes Berg1-2/+2
The netdev broadcast address cannot change from all-ones so there's no need to use it; we can instead hard-code it. Since we already have an instance in tkip.c, which will be shared if it is marked static const, doing this reduces text size at no data/bss cost. The real motivation for this is, of course, the desire to get rid of almost all uses of netdevs in mac80211 so that auditing their use becomes easier. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-13mac80211: update copyrights to 2009Rui Paulo1-1/+1
Signed-off-by: Rui Paulo <rpaulo@gmail.com> Signed-off-by: Javier Cardona <javier@cozybit.com> Reviewed-by: Andrey Yurovsky <andrey@cozybit.com> Tested-by: Brian Cavagnolo <brian@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-13mac80211: add nl80211/cfg80211 handling of the new mesh root mode option.Rui Paulo1-0/+1
Signed-off-by: Rui Paulo <rpaulo@gmail.com> Signed-off-by: Javier Cardona <javier@cozybit.com> Reviewed-by: Andrey Yurovsky <andrey@cozybit.com> Tested-by: Brian Cavagnolo <brian@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-13mac80211: implement a timer to send RANN action framesRui Paulo1-0/+3
RANN (Root Annoucement) frame TX. Send an action frame every second trying to build a path to all nodes on the mesh. Signed-off-by: Rui Paulo <rpaulo@gmail.com> Signed-off-by: Javier Cardona <javier@cozybit.com> Reviewed-by: Andrey Yurovsky <andrey@cozybit.com> Tested-by: Brian Cavagnolo <brian@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-13mac80211: replace "destination" with "target" to follow the specRui Paulo1-5/+5
Resulting object files have the same MD5 as before. Signed-off-by: Rui Paulo <rpaulo@gmail.com> Signed-off-by: Javier Cardona <javier@cozybit.com> Reviewed-by: Andrey Yurovsky <andrey@cozybit.com> Tested-by: Brian Cavagnolo <brian@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-13mac80211: update PERR frame formatRui Paulo1-2/+7
Update the PERR IE frame format according to latest draft (3.03). Signed-off-by: Rui Paulo <rpaulo@gmail.com> Signed-off-by: Javier Cardona <javier@cozybit.com> Reviewed-by: Andrey Yurovsky <andrey@cozybit.com> Tested-by: Brian Cavagnolo <brian@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-11mac80211: update the format of path selection framesRui Paulo1-0/+1
Update the format of path selection frames according to latest draft (3.03). Signed-off-by: Rui Paulo <rpaulo@gmail.com> Signed-off-by: Javier Cardona <javier@cozybit.com> Reviewed-by: Andrey Yurovsky <andrey@cozybit.com> Tested-by: Brian Cavagnolo <brian@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-11mac80211: update peer link management IE and action framesRui Paulo1-1/+1
Update the length and format of the peer link management action frames. Signed-off-by: Rui Paulo <rpaulo@gmail.com> Signed-off-by: Javier Cardona <javier@cozybit.com> Reviewed-by: Andrey Yurovsky <andrey@cozybit.com> Tested-by: Brian Cavagnolo <brian@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-11mac80211: set MESH_TTL to 31Rui Paulo1-1/+1
Update the mesh time to live field to 31 according to draft 3.03. Signed-off-by: Rui Paulo <rpaulo@gmail.com> Signed-off-by: Javier Cardona <javier@cozybit.com> Reviewed-by: Andrey Yurovsky <andrey@cozybit.com> Tested-by: Brian Cavagnolo <brian@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-20mac80211: Decouple fail_avg stats used by mesh from rate control algorithm.Javier Cardona1-0/+2
Mesh uses the tx failure average to compute the (m)path metric. This used to be done inside the rate control module. This patch breaks the dependency between the mesh stack and the rate control algorithm. Mesh will now work independently of the chosen rate control algorithm. The mesh stack keeps a moving average of the average transmission losses for each mesh peer station. If the fail average exceeds a certain threshold, the peer link is marked as broken. Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-14mac80211: Move mpath and mpp growth to mesh workqueue.Javier Cardona1-1/+19
This prevents calling rcu_synchronize from within the tx path by moving the table growth code to the mesh workqueue. Move mesh_table_free and mesh_table_grow from mesh.c to mesh_pathtbl.c and declare them static. Also, re-enable mesh in Kconfig and update the configuration description. Signed-off-by: Javier Cardona <javier@cozybit.com> Tested-by: Andrey Yurovsky <andrey@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-14mac80211: Assign a default mesh beaconing interval.Javier Cardona1-0/+1
The mesh stack was enabling beaconing without specifying an interval. This patch defines a default beaconing interval of 1s. Incidentally, this fixes mesh beaconing in mac80211_hwsim devices. Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-14mac80211: Use 3-address format for mesh broadcast frames.Javier Cardona1-1/+4
The 11s task group recently changed the frame mesh multicast/broadcast frame format to use 3-address. This was done to avoid interactions with widely deployed lazy-WDS access points. This patch changes the format of group addressed frames, both mesh-originated and proxied, to use the data format defined in draft D2.08 and forward. The address fields used for group addressed frames is: In 802.11 header ToDS:0 FromDS:1 addr1: DA (broadcast/multicast address) addr2: TA addr3: Mesh SA In address extension header: addr4: SA (only present if frame was proxied) Note that this change breaks backward compatibility with earlier mesh stack versions. Signed-off-by: Andrey Yurovsky <andrey@cozybit.com> Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-14mac80211: Improve dequeing from mpath frame queue.Javier Cardona1-1/+1
Also, fix typo in comment. Signed-off-by: Javier Cardona <javier@cozybit.com> Tested-by: Andrey Yurovsky <andrey@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-14nl80211: add generation number to all dumpsJohannes Berg1-0/+2
In order for userspace to be able to figure out whether it obtained a consistent snapshot of data or not when using netlink dumps, we need to have a generation number in each dump message that indicates whether the list has changed or not -- its value is arbitrary. This patch adds such a number to all dumps, this needs some mac80211 involvement to keep track of a generation number to start with when adding/removing mesh paths or stations. The wiphy and netdev lists can be fully handled within cfg80211, of course, but generation numbers need to be stored there as well. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-10mac80211: push rx status into skb->cbJohannes Berg1-2/+1
Within mac80211, we often need to copy the rx status into skb->cb. This is wasteful, as drivers could be building it in there to start with. This patch changes the API so that drivers are expected to pass the RX status in skb->cb, now accessible as IEEE80211_SKB_RXCB(skb). It also updates all drivers to pass the rx status in there, but only by making them memcpy() it into place before the call to the receive function (ieee80211_rx(_irqsafe)). Each driver can now be optimised on its own schedule. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.