| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Instead of just having an airtime flag in debugfs, turn AQL into a proper
NL80211_EXT_FEATURE, so drivers can turn it on when they are ready, and so
we also expose the presence of the feature to userspace.
This also has the effect of flipping the default, so drivers have to opt in
to using AQL instead of getting it by default with TXQs. To keep
functionality the same as pre-patch, we set this feature for ath10k (which
is where it is needed the most).
While we're at it, split out the debugfs interface so AQL gets its own
per-station debugfs file instead of using the 'airtime' file.
[Johannes:]
This effectively disables AQL for iwlwifi, where it fixes a number of
issues:
* TSO in iwlwifi is causing underflows and associated warnings in AQL
* HE (802.11ax) rates aren't reported properly so at HE rates, AQL could
never have a valid estimate (it'd use 6 Mbps instead of up to 2400!)
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20191212111437.224294-1-toke@redhat.com
Fixes: 3ace10f5b5ad ("mac80211: Implement Airtime-based Queue Limit (AQL)")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In order for the Fq_CoDel algorithm integrated in mac80211 layer to operate
effectively to control excessive queueing latency, the CoDel algorithm
requires an accurate measure of how long packets stays in the queue, AKA
sojourn time. The sojourn time measured at the mac80211 layer doesn't
include queueing latency in the lower layer (firmware/hardware) and CoDel
expects lower layer to have a short queue. However, most 802.11ac chipsets
offload tasks such TX aggregation to firmware or hardware, thus have a deep
lower layer queue.
Without a mechanism to control the lower layer queue size, packets only
stay in mac80211 layer transiently before being sent to firmware queue.
As a result, the sojourn time measured by CoDel in the mac80211 layer is
almost always lower than the CoDel latency target, hence CoDel does little
to control the latency, even when the lower layer queue causes excessive
latency.
The Byte Queue Limits (BQL) mechanism is commonly used to address the
similar issue with wired network interface. However, this method cannot be
applied directly to the wireless network interface. "Bytes" is not a
suitable measure of queue depth in the wireless network, as the data rate
can vary dramatically from station to station in the same network, from a
few Mbps to over Gbps.
This patch implements an Airtime-based Queue Limit (AQL) to make CoDel work
effectively with wireless drivers that utilized firmware/hardware
offloading. AQL allows each txq to release just enough packets to the lower
layer to form 1-2 large aggregations to keep hardware fully utilized and
retains the rest of the frames in mac80211 layer to be controlled by the
CoDel algorithm.
Signed-off-by: Kan Yan <kyan@google.com>
[ Toke: Keep API to set pending airtime internal, fix nits in commit msg ]
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20191119060610.76681-4-kyan@google.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In ieee80211_tx_status() we don't have an sdata struct when looking up the
destination sta. Instead, we just do a lookup by the vif addr that is the
source of the packet being completed. Factor this out into a new sta_info
getter helper, since we need to use it for accounting AQL as well.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20191112130835.382062-1-toke@redhat.com
[remove internal rcu_read_lock(), document instead]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In the first 5 minutes after boot (time of INITIAL_JIFFIES),
ieee80211_sta_last_active() returns zero if last_ack is zero. This
leads to "inactive time" showing jiffies_to_msecs(jiffies).
# iw wlan0 station get fc:ec:da:64:a6:dd
Station fc:ec:da:64:a6:dd (on wlan0)
inactive time: 4294894049 ms
.
.
connected time: 70 seconds
Fix by returning last_rx if last_ack == 0.
Signed-off-by: Ahmed Zaki <anzaki@gmail.com>
Link: https://lore.kernel.org/r/20191031121243.27694-1-anzaki@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Minor overlapping changes in the btusb and ixgbe drivers.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Layer 2 Update frame is used to update bridges when a station roams
to another AP even if that STA does not transmit any frames after the
reassociation. This behavior was described in IEEE Std 802.11F-2003 as
something that would happen based on MLME-ASSOCIATE.indication, i.e.,
before completing 4-way handshake. However, this IEEE trial-use
recommended practice document was published before RSN (IEEE Std
802.11i-2004) and as such, did not consider RSN use cases. Furthermore,
IEEE Std 802.11F-2003 was withdrawn in 2006 and as such, has not been
maintained amd should not be used anymore.
Sending out the Layer 2 Update frame immediately after association is
fine for open networks (and also when using SAE, FT protocol, or FILS
authentication when the station is actually authenticated by the time
association completes). However, it is not appropriate for cases where
RSN is used with PSK or EAP authentication since the station is actually
fully authenticated only once the 4-way handshake completes after
authentication and attackers might be able to use the unauthenticated
triggering of Layer 2 Update frame transmission to disrupt bridge
behavior.
Fix this by postponing transmission of the Layer 2 Update frame from
station entry addition to the point when the station entry is marked
authorized. Similarly, send out the VLAN binding update only if the STA
entry has already been authorized.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Report timestamp for when sta becomes associated.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Link: https://lore.kernel.org/r/20190809180001.26393-2-greearb@candelatech.com
[fix ktime_get_boot_ns() to ktime_get_boottime_ns(), assoc_at type to u64]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The remove_sta_debugfs callback in struct rate_control_ops is no longer
used by any driver, as there is no need for it (the debugfs directory is
already removed recursivly by the mac80211 core.) Because no one needs
it, just remove it to keep anyone else from accidentally using it in the
future.
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20190612142658.12792-5-gregkh@linuxfoundation.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Minor SPDX change conflict.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Even if we have a station, we currently call rate_control_send_low()
with the NULL station unless further rate control (driver, minstrel)
has been initialized.
Change this so we can use more information about the station to use
a better rate. For example, when we associate with an AP, we will
now use the lowest rate it advertised as supported (that we can)
rather than the lowest mandatory rate. This aligns our behaviour
with most other 802.11 implementations.
To make this possible, we need to also ensure that we have non-zero
rates at all times, so in case we really have *nothing* pre-fill
the supp_rates bitmap with the very lowest mandatory bitmap (11b
and 11a on 2.4 and 5 GHz respectively).
Additionally, hostapd appears to be giving us an empty supported
rates bitmap (it can and should do better, since the STA must have
supported for at least the basic rates in the BSS), so ignore any
such bitmaps that would actually zero out the supp_rates, and in
that case just keep the pre-filled mandatory rates.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add support for Extended Key ID as defined in IEEE 802.11-2016.
- Implement the nl80211 API for Extended Key ID
- Extend mac80211 API to allow drivers to support Extended Key ID
- Enable Extended Key ID by default for drivers only supporting SW
crypto (e.g. mac80211_hwsim)
- Allow unicast Tx usage to be supressed (IEEE80211_KEY_FLAG_NO_AUTO_TX)
- Select the decryption key based on the MPDU keyid
- Enforce existing assumptions in the code that rekeys don't change the
cipher
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
[remove module parameter]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add support for mesh airtime link metric attribute
NL80211_STA_INFO_AIRTIME_LINK_METRIC.
Signed-off-by: Narayanraddi Masti <team.nmasti@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This adds airtime accounting and scheduling to the mac80211 TXQ
scheduler. A new callback, ieee80211_sta_register_airtime(), is added
that drivers can call to report airtime usage for stations.
When airtime information is present, mac80211 will schedule TXQs
(through ieee80211_next_txq()) in a way that enforces airtime fairness
between active stations. This scheduling works the same way as the ath9k
in-driver airtime fairness scheduling. If no airtime usage is reported
by the driver, the scheduler will default to round-robin scheduling.
For drivers that don't control TXQ scheduling in software, a new API
function, ieee80211_txq_may_transmit(), is added which the driver can use
to check if the TXQ is eligible for transmission, or should be throttled to
enforce fairness. Calls to this function must also be enclosed in
ieee80211_txq_schedule_{start,end}() calls to ensure proper locking.
The API ieee80211_txq_may_transmit() also ensures that TXQ list will be
aligned aginst driver's own round-robin scheduler list. i.e it rotates
the TXQ list till it makes the requested node becomes the first entry
in TXQ list. Thus both the TXQ list and driver's list are in sync.
Co-developed-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Louie Lu <git@louie.lu>
[added debugfs write op to reset airtime counter]
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This adds an API to mac80211 to handle scheduling of TXQs. The interface
between driver and mac80211 for TXQ handling is changed by adding two new
functions: ieee80211_next_txq(), which will return the next TXQ to schedule
in the current round-robin rotation, and ieee80211_return_txq(), which the
driver uses to indicate that it has finished scheduling a TXQ (which will
then be put back in the scheduling rotation if it isn't empty).
The driver must call ieee80211_txq_schedule_start() at the start of each
scheduling session, and ieee80211_txq_schedule_end() at the end. The API
then guarantees that the same TXQ is not returned twice in the same
session (so a driver can loop on ieee80211_next_txq() without worrying
about breaking the loop.
Usage of the new API is optional, so drivers can be ported one at a time.
In this patch, the actual scheduling performed by mac80211 is simple
round-robin, but a subsequent commit adds airtime fairness awareness to the
scheduler.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
[minor kernel-doc fix, propagate sparse locking checks out]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Capture the current state of gate connectivity from the mesh
formation field in mesh config whenever we receive a beacon,
and report that via GET_STATION. This allows applications
doing mesh peering in userspace to make peering decisions
based on peers' current upstream connectivity.
Signed-off-by: Bob Copeland <bobcopeland@fb.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
We have a pointer called 'tidstats' that shadows a bool function
argument with the same name, but we actually only use it once so
just remove the pointer.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Some drivers may want to also use the TXQ abstraction with
non-data packets that need powersave buffering, so add a
hardware flag to allow this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Modify the API to include all ACK frames in average ACK
signal strength reporting, not just ACKs for data frames.
Make exposing the data conditional on implementing the
extended feature flag.
This is how it was really implemented in mac80211, update
the code there to use the new defines and clean up some of
the setting code.
Keep nl80211.h source compatibility by keeping the old names.
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
[rewrite commit log, change compatibility to be old=new
instead of the other way around, update kernel-doc,
roll in mac80211 changes, make mac80211 depend on valid
bit instead of HW flag]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The BIT macro uses unsigned long which some architectures handle as 32 bit
and therefore might cause macro's shift to overflow when used on a value
equals or larger than 32 (NL80211_STA_INFO_RX_DURATION and afterwards).
Since 'filled' member in station_info changed to u64, BIT_ULL macro
should be used with all NL80211_STA_INFO_* attribute types instead of BIT
to prevent future possible bugs when one will use BIT macro for higher
attributes by mistake.
This commit cleans up all usages of BIT macro with the above field
in mac80211 by changing it to BIT_ULL instead.
Signed-off-by: Omer Efrat <omer.efrat@tandemg.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add support for HE in mac80211 conforming with P802.11ax_D1.4.
Johannes: Fix another bug with the buf_size comparison in agg-rx.c.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Support the new random SN and minimal probe request contents
scan flags for the case of software scan - for hardware scan
the drivers need to opt in, but may need to do only that,
depending on their implementation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
|
|
This fixes memory leaks in the case where we just have the
station info on the stack for internal usage without sending
it to cfg80211.
Fixes: 8689c051a201 ("cfg80211: dynamically allocate per-tid stats for station info")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
With the addition of TXQ stats in the per-tid statistics the struct
station_info grew significantly. This resulted in stack size warnings
due to the structure itself being above the limit for the warnings.
Add an allocation function that those who want to provide per-tid
stats should use to allocate the tid array, i.e.
struct station_info::pertid.
Cc: Toke Høiland-Jørgensen <toke@toke.dk>
Fixes: 52539ca89f36 ("cfg80211: Expose TXQ stats and parameters to userspace")
Signed-off-by: Arend van Spriel <aspriel@gmail.com>
[johannes: fix missing BIT() and logic by removing]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This adds support to mac80211 to export TXQ stats via the newly added
cfg80211 API.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The driver will process the RSSI if available and send it to mac80211.
mac80211 will compute the weighted average of ack RSSI for stations.
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The data structure is initialized to all zeroes, and
we already rely on that in other places, so remove the
pointless assignment to 0.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
|
|
sta_info_alloc can be called from atomic paths (such as RX path)
so we need to call pcpu_alloc with the correct gfp.
Fixes: c9c5962b56c1 ("mac80211: enable collecting station statistics per-CPU")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If sta_info_alloc fails after allocating the per CPU statistics,
they are not properly freed.
Fixes: c9c5962b56c1 ("mac80211: enable collecting station statistics per-CPU")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This allows users to get ack signal strength of
last transmitted frame.
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
This removes the tid mapping array and expands the tid structures to
add a pointer back to the station, along with the tid index itself.
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
[switch tid variables to u8, the valid range is 0-15 at most,
initialize tid_tx->sta/tid properly]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Pull networking updates from David Miller:
"Highlights:
1) Maintain the TCP retransmit queue using an rbtree, with 1GB
windows at 100Gb this really has become necessary. From Eric
Dumazet.
2) Multi-program support for cgroup+bpf, from Alexei Starovoitov.
3) Perform broadcast flooding in hardware in mv88e6xxx, from Andrew
Lunn.
4) Add meter action support to openvswitch, from Andy Zhou.
5) Add a data meta pointer for BPF accessible packets, from Daniel
Borkmann.
6) Namespace-ify almost all TCP sysctl knobs, from Eric Dumazet.
7) Turn on Broadcom Tags in b53 driver, from Florian Fainelli.
8) More work to move the RTNL mutex down, from Florian Westphal.
9) Add 'bpftool' utility, to help with bpf program introspection.
From Jakub Kicinski.
10) Add new 'cpumap' type for XDP_REDIRECT action, from Jesper
Dangaard Brouer.
11) Support 'blocks' of transformations in the packet scheduler which
can span multiple network devices, from Jiri Pirko.
12) TC flower offload support in cxgb4, from Kumar Sanghvi.
13) Priority based stream scheduler for SCTP, from Marcelo Ricardo
Leitner.
14) Thunderbolt networking driver, from Amir Levy and Mika Westerberg.
15) Add RED qdisc offloadability, and use it in mlxsw driver. From
Nogah Frankel.
16) eBPF based device controller for cgroup v2, from Roman Gushchin.
17) Add some fundamental tracepoints for TCP, from Song Liu.
18) Remove garbage collection from ipv6 route layer, this is a
significant accomplishment. From Wei Wang.
19) Add multicast route offload support to mlxsw, from Yotam Gigi"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2177 commits)
tcp: highest_sack fix
geneve: fix fill_info when link down
bpf: fix lockdep splat
net: cdc_ncm: GetNtbFormat endian fix
openvswitch: meter: fix NULL pointer dereference in ovs_meter_cmd_reply_start
netem: remove unnecessary 64 bit modulus
netem: use 64 bit divide by rate
tcp: Namespace-ify sysctl_tcp_default_congestion_control
net: Protect iterations over net::fib_notifier_ops in fib_seq_sum()
ipv6: set all.accept_dad to 0 by default
uapi: fix linux/tls.h userspace compilation error
usbnet: ipheth: prevent TX queue timeouts when device not ready
vhost_net: conditionally enable tx polling
uapi: fix linux/rxrpc.h userspace compilation errors
net: stmmac: fix LPI transitioning for dwmac4
atm: horizon: Fix irq release error
net-sysfs: trigger netlink notification on ifalias change via sysfs
openvswitch: Using kfree_rcu() to simplify the code
openvswitch: Make local function ovs_nsh_key_attr_size() static
openvswitch: Fix return value check in ovs_meter_cmd_features()
...
|
|
Please do not apply this to mainline directly, instead please re-run the
coccinelle script shown below and apply its output.
For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't harmful, and changing them results in
churn.
However, for some features, the read/write distinction is critical to
correct operation. To distinguish these cases, separate read/write
accessors must be used. This patch migrates (most) remaining
ACCESS_ONCE() instances to {READ,WRITE}_ONCE(), using the following
coccinelle script:
----
// Convert trivial ACCESS_ONCE() uses to equivalent READ_ONCE() and
// WRITE_ONCE()
// $ make coccicheck COCCI=/home/mark/once.cocci SPFLAGS="--include-headers" MODE=patch
virtual patch
@ depends on patch @
expression E1, E2;
@@
- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)
@ depends on patch @
expression E;
@@
- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: snitzer@redhat.com
Cc: thor.thayer@linux.intel.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-19-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. This requires adding a pointer back
to the sta_info since container_of() can't resolve the sta_info.
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Sometimes a station is added already in ASSOC state. For example,
in AP mode, when a client station didn't get assoc resp and sends
an assoc req again. If a station is inserted when its state is ASSOC
or higher, the min chandef and allow_p2p_go_ps should be recalculated
again after the insertion.
Before this patch the recalculation happened only in sta_info_move_state
which occurs before the insertion of the sta and thus even though
it calls ieee80211_recalc_min_chandef/_p2p_go_ps_allowed functions,
since sdata->local->sta_list is still empty at this point, it doesn't do
anything.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions (skb_put, __skb_put and pskb_put) return void *
and remove all the casts across the tree, adding a (u8 *) cast only
where the unsigned char pointer was used directly, all done with the
following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_put, __skb_put };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_put, __skb_put };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
which actually doesn't cover pskb_put since there are only three
users overall.
A handful of stragglers were converted manually, notably a macro in
drivers/isdn/i4l/isdn_bsdcomp.c and, oddly enough, one of the many
instances in net/bluetooth/hci_sock.c. In the former file, I also
had to fix one whitespace problem spatch introduced.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This brings in commit 7a7c0a6438b8 ("mac80211: fix TX aggregation
start/stop callback race") to allow the follow-up cleanup.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In the commit enabling per-CPU station statistics, I inadvertedly
copy-pasted some code to update rx_packets and forgot to change it
to update rx_dropped_misc. Fix that.
This addresses https://bugzilla.kernel.org/show_bug.cgi?id=195953.
Fixes: c9c5962b56c1 ("mac80211: enable collecting station statistics per-CPU")
Reported-by: Petru-Florin Mihancea <petrum@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
CoDel can be too aggressive if a station sends at a very low rate,
leading reduced throughput. This gets worse the more stations are
present, as each station gets more bursty the longer the round-robin
scheduling between stations takes.
This adds dynamic adjustment of CoDel parameters per station. It uses
the rate selection information to estimate throughput and sets more
lenient CoDel parameters if the estimated throughput is below a
threshold (modified by the number of active stations).
A new callback is added that drivers can use to notify mac80211 about
changes in expected throughput, so the same adjustment can be made for
cards that implement rate control in firmware. Drivers that don't use
this will just get the default parameters.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
[remove currently unnecessary EXPORT_SYMBOL, fix kernel-doc, remove
inline annotation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Existing API 'ieee80211_get_sdata_band' returns default 2 GHz band even
if the channel context configuration is NULL. This crashes for chipsets
which support 5 Ghz alone when it tries to access members of 'sband'.
Channel context configuration can be NULL in multivif case and when
channel switch is in progress (or) when it fails. Fix this by replacing
the API 'ieee80211_get_sdata_band' with 'ieee80211_get_sband' which
returns a NULL pointer for sband when the channel configuration is NULL.
An example scenario is as below:
In multivif mode (AP + STA) with drivers like ath10k, when we do a
channel switch in the AP vif (which has a number of clients connected)
and a STA vif which is connected to some other AP, when the channel
switch in AP vif fails, while the STA vifs tries to connect to the
other AP, there is a window where the channel context is NULL/invalid
and this results in a crash while the clients connected to the AP vif
tries to reconnect and this race is very similar to the one investigated
by Michal in https://patchwork.kernel.org/patch/3788161/ and this does
happens with hardware that supports 5Ghz alone after long hours of
testing with continuous channel switch on the AP vif
ieee80211 phy0: channel context reservation cannot be finalized because
some interfaces aren't switching
wlan0: failed to finalize CSA, disconnecting
wlan0-1: deauthenticating from 8c:fd:f0:01:54:9c by local choice
(Reason: 3=DEAUTH_LEAVING)
WARNING: CPU: 1 PID: 19032 at net/mac80211/ieee80211_i.h:1013 sta_info_alloc+0x374/0x3fc [mac80211]
[<bf77272c>] (sta_info_alloc [mac80211])
[<bf78776c>] (ieee80211_add_station [mac80211]))
[<bf73cc50>] (nl80211_new_station [cfg80211])
Unable to handle kernel NULL pointer dereference at virtual
address 00000014
pgd = d5f4c000
Internal error: Oops: 17 [#1] PREEMPT SMP ARM
PC is at sta_info_alloc+0x380/0x3fc [mac80211]
LR is at sta_info_alloc+0x37c/0x3fc [mac80211]
[<bf772738>] (sta_info_alloc [mac80211])
[<bf78776c>] (ieee80211_add_station [mac80211])
[<bf73cc50>] (nl80211_new_station [cfg80211]))
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Instead of hand-coding the bit manipulations, use the bitfield
macros to generate the code for the encoded bitrate.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
We don't really need three different bits for each, since the
types are mutually exclusive. Use just two bits for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Tracing is limited to 100 characters and this message passes
the limit when there are a few buffered frames. Shorten it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
iwlwifi now supports RSS and can't let mac80211 track the
PS state based on the Rx frames since they can come out of
order. iwlwifi is now advertising AP_LINK_PS, and uses
explicit notifications to teach mac80211 about the PS state
of the stations and the PS poll / uAPSD trigger frames
coming our way from the peers.
Because of that, the TIM stopped being maintained in
mac80211. I tried to fix this in commit c68df2e7be0c
("mac80211: allow using AP_LINK_PS with mac80211-generated TIM IE")
but that was later reverted by Felix in commit 6c18a6b4e799
("Revert "mac80211: allow using AP_LINK_PS with mac80211-generated TIM IE")
since it broke drivers that do not implement set_tim.
Since none of the drivers that set AP_LINK_PS have the
set_tim() handler set besides iwlwifi, I can bail out in
__sta_info_recalc_tim if AP_LINK_PS AND .set_tim is not
implemented.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
|
|
Johannes Berg says:
====================
For 4.11, we seem to have more than in the past few releases:
* socket owner support for connections, so when the wifi
manager (e.g. wpa_supplicant) is killed, connections are
torn down - wpa_supplicant is critical to managing certain
operations, and can opt in to this where applicable
* minstrel & minstrel_ht updates to be more efficient (time and space)
* set wifi_acked/wifi_acked_valid for skb->destructor use in the
kernel, which was already available to userspace
* don't indicate new mesh peers that might be used if there's no
room to add them
* multicast-to-unicast support in mac80211, for better medium usage
(since unicast frames can use *much* higher rates, by ~3 orders of
magnitude)
* add API to read channel (frequency) limitations from DT
* add infrastructure to allow randomizing public action frames for
MAC address privacy (still requires driver support)
* many cleanups and small improvements/fixes across the board
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the commit below, I forgot to translate the mac80211's
AC to QoS IE order. Moreover, the condition in the if was
wrong. Fix both issues.
This bug would hit only with clients that didn't set all
the ACs as delivery enabled.
Fixes: f438ceb81d4 ("mac80211: uapsd_queues is in QoS IE order")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This speeds up the function in case a station already exists by avoiding
calling an expensive kzalloc just to free it again after the next check.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
Toke Høiland-Jørgensen
Kan Yan
Ahmed Zaki
David S. Miller
Jouni Malinen
Ben Greear
Greg Kroah-Hartman
Thomas Gleixner
Johannes Berg
Alexander Wetzel
Narayanraddi Masti
Toke Høiland-Jørgensen
Bob Copeland
Balaji Pothunoori
Omer Efrat
Luca Coelho
Arend van Spriel
Sara Sharon
Venkateswara Naralasetty
Kees Cook
Linus Torvalds
Mark Rutland
Gregory Greenman
Mohammed Shafi Shajakhan
Emmanuel Grumbach
Koen Vandeputte