| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
In the likely case that probe_count is 0, don't write to the
memory there.
Also use ifmgd consistently in the function, instead of using
sdata->u.mgd as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The code is only used with iwlwifi, but still should have proper
mac80211 naming scheme; fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Avoid the really strange %s%s%s expression, use an array
of flag names and check that all flags are present.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If the device implements dynamic PS itself, there's no need
to ever start the dynamic powersave timer on RX.
While at it, fix up some indentation in this code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Since the previous patch, the struct only has a single member,
so remove the struct and leave just the single member.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Remove unused variable in per STA debugfs structure, 'commit 34e895075e21
("mac80211: allow station add/remove to sleep")' removed the only user of
'add_has_run'.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Currently the debugfs entry for starting aggregation session
starts it with timeout of 5 seconds. Allow opening a session
with a custom timeout (according to spec 0 is no timeout).
while at it, refactor the function and remove the magic numbers.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
NETIF_F_RXCSUM is not in the white list, though some
drivers may want to set it in order to enable seeing the
actual RX checksum status in ethtool.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Allow publishing RRM capabilities for features that are not
HW dependent.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There were a few issues that were slowing down the process of finding
the optimal rate, especially on devices with multi-rate retry
limitations:
When max_tp_rate[0] was slower than max_tp_rate[1], the code did not
sample max_tp_rate[1], which would often allow it to switch places with
max_tp_rate[0] (e.g. if only the first sampling attempts were bad, but the
rate is otherwise good).
Also, sample attempts of rates between max_tp_rate[0] and [1] were being
ignored in this case, because the code only checked if the rate was
slower than [1].
Fix this by checking against the fastest / second fastest max_tp_rate
instead of assuming a specific order between the two.
In my tests this patch significantly reduces the time until minstrel_ht
finds the optimal rate right after assoc
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Since we enqueued the frame that was supposed to be sent
during the SP, and that frame may very well cary the
IEEE80211_TX_STATUS_EOSP bit, we may never close the SP
(WLAN_STA_SP will never be cleared). If that happens, we
will not open any new SP and will never respond to any poll
frame from the client.
Clear WLAN_STA_SP manually if a frame that was polled during
the SP is queued because of a starting A-MPDU session. The
client may not see the EOSP bit, but it will at least be
able to poll new frames in another SP.
Reported-by: Alesya Shapira <alesya.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[remove erroneous comment]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
It is possible that the station is connected to an AP
with bandwidth of 80+80MHz or 160MHz. In such cases
there is no need to perform an upgrade as the maximal
supported bandwidth is 80MHz.
In addition, when upgrading and setting center_freq1
and bandwidth to 80MHz also set center_freq2 to 0.
Fixes: 0fabfaafec3a ("mac80211: upgrade BW of TDLS peers when possible"
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Frames that are sent between
ampdu_action(IEEE80211_AMPDU_TX_START) and the move to the
HT_AGG_STATE_OPERATIONAL state are buffered.
If we try to start an A-MPDU session while the peer is
sleeping and polling frames with U-APSD, we may have frames
that will be buffered by ieee80211_tx_prep_agg. These frames
have IEEE80211_TX_CTL_NO_PS_BUFFER set since they are sent to
a sleeping client and possibly IEEE80211_TX_STATUS_EOSP.
If the frame is buffered, we need clear these two flags
since they will be re-sent after the move to
HT_AGG_STATE_OPERATIONAL state which is very likely to
happen after the SP ends.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Commit 976bd9efdae6 ("mac80211: move beacon_loss_count into ifmgd")
removed the member from the sta_info struct but the description stayed
lingering. Remove it.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
By default, the rhashtable logic will fail to insert
objects if the key-chains are too long and un-balanced.
In the degenerate case where mac80211 is creating many
virtual interfaces connected to the same peer(s), this
case can happen.
St insecure_elasticity to true to allow chains to grow
as long as needed.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[remove message, change commit message slightly]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The original hand-implemented hash-table in mac80211 couldn't result
in insertion errors, and while converting to rhashtable I evidently
forgot to check the errors.
This surfaced now only because Ben is adding many identical keys and
that resulted in hidden insertion errors.
Cc: stable@vger.kernel.org
Fixes: 7bedd0cfad4e1 ("mac80211: use rhashtable for station table")
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Fall back to rate control if the requested bitrate was not found.
Fixes: dfdfc2beb0dd ("mac80211: Parse legacy and HT rate in injected frames")
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The MCS bandwidth part of the radiotap header is 2 bits wide. The full 2
bit have to compared against IEEE80211_RADIOTAP_MCS_BW_40 and not only if
the first bit is set. Otherwise IEEE80211_RADIOTAP_MCS_BW_40 can be
confused with IEEE80211_RADIOTAP_MCS_BW_20U.
Fixes: dfdfc2beb0dd ("mac80211: Parse legacy and HT rate in injected frames")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Some devices, like iwlwifi, have RSS queues. This may cause a
situation where a disassociation is handled in control path and
results in station removal while there are prior RX frames
that were still not processed in other queues. When they will
be processed the station will be gone, and the frames will be
dropped.
Add a synchronization interface to avoid that. When driver returns
from the synchronization mac80211 may remove the station.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In the time since the mesh path table was implemented as an
RCU-traversable, dynamically growing hash table, a generic RCU
hashtable implementation was added to the kernel.
Switch the mesh path table over to rhashtable to remove some code
and also gain some features like automatic shrinking.
Cc: Thomas Graf <tgraf@suug.ch>
Cc: netdev@vger.kernel.org
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The mesh path table uses a struct mesh_node in its hlists in
order to support a resizable hash table: the mesh_node provides
an indirection to the actual mesh path so that two different
bucket lists can point to the same path entry.
However, for the known gates list, we don't need this indirection
because there is ever only one list. So we can just embed the
hlist_node in the mesh path itself, which simplifies things a bit
and saves a linear search whenever we need to find an item in
the list.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Remove duplicate code to allocate and initialize a mesh
path or mesh proxy path.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Now that the sdata pointer is the same for all entries of a
path table, hashing it is pointless, so hash only the address.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The mesh path and mesh gate hashtables are global, containing
all of the mpaths for every mesh interface, but the paths are
all tied logically to a single interface. The common case is
just a single mesh interface, so optimize for that by moving
the global hashtable into the per-interface struct.
Doing so allows us to drop sdata pointer comparisons inside
the lookups and also saves a few bytes of BSS and data.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If the cfg80211 scan trigger operation specifies a single BSSID, use
that value instead of the wildcard BSSID in the Probe Request frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The min_def chanctx is affected not only by the current chandef, but
sometimes also by other stations on the vif. There's a valid scenario
where a TDLS peer can widen its BW, thereby causing the min_def
to increase.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The previous approach simply ignored chandef restrictions when calculating
the appropriate peer BW for a WIDER_BW peer. This could result in a
regulatory violation if both peers indicated 80MHz support, but the
regdomain forbade it.
Change the approach to setting a WIDER_BW peer's BW. Don't exempt it from
the chandef width at first. If during TDLS negotiation the chandef width
is upgraded, update the peer's BW to match.
Fixes: 0fabfaafec3a ("mac80211: upgrade BW of TDLS peers when possible")
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Even if the current chandef width is equal to the station's max-BW, it
doesn't mean it's a valid width for TDLS. Make sure to always check
regulatory constraints in these cases.
Fixes: 0fabfaafec3a ("mac80211: upgrade BW of TDLS peers when possible")
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Buffered multicast frames must be passed to the driver directly via
drv_tx instead of going through the txq, otherwise they cannot easily be
scheduled to be sent after DTIM.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When HW crypto is used, there's no need for the CCMP/GCMP MIC to
be available to mac80211, and the hardware might have removed it
already after checking. The MIC is also useless to have when the
frame is already decrypted, so allow indicating that it's not
present.
Since we are running out of bits in mac80211_rx_flags, make
the flags field a u64.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This was requested by Android, and the appropriate cfg80211 API
had been added by Dmitry. Support it in mac80211, allowing drivers
to provide the timestamp.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add VHT radiotap parsing support to ieee80211_parse_tx_radiotap().
That capability has been tested using a d-link dir-860l rev b1 running
OpenWrt trunk and mt76 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Several cases of overlapping changes, as well as one instance
(vxlan) of a bug fix in 'net' overlapping with code movement
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since offset is zero, it's not necessary to use set function. Reset
function is straightforward, and will remove the unnecessary add
operation in set function.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Johannes Berg says:
====================
Here are a few more fixes for the current cycle:
* check GCMP encryption vs. fragmentation properly; we'd found
this problem quite a while ago but waited for the 802.11 spec
to be updated
* fix RTS/CTS logic in minstrel_ht
* fix RX of certain public action frames in AP mode
* add mac80211_hwsim to MAC80211 in MAINTAINERS, this helps
the kbuild robot pick up the right tree for it
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Johannes Berg says:
====================
Here's another round of updates for -next:
* big A-MSDU RX performance improvement (avoid linearize of paged RX)
* rfkill changes: cleanups, documentation, platform properties
* basic PBSS support in cfg80211
* MU-MIMO action frame processing support
* BlockAck reordering & duplicate detection offload support
* various cleanups & little fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RTS/CTS needs to be enabled if the rate is a fallback rate *or* if it's
a dual-stream rate and the sta is in dynamic SMPS mode.
Cc: stable@vger.kernel.org
Fixes: a3ebb4e1b763 ("mac80211: minstrel_ht: handle peers in dynamic SMPS")
Reported-by: MatÃas Richart <mrichart@fing.edu.uy>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Public Action frames use special rules for how the BSSID field (Address
3) is set. A wildcard BSSID is used in cases where the transmitter and
recipient are not members of the same BSS. As such, we need to accept
Public Action frames with wildcard BSSID.
Commit db8e17324553 ("mac80211: ignore frames between TDLS peers when
operating as AP") added a rule that drops Action frames to TDLS-peers
based on an Action frame having different DA (Address 1) and BSSID
(Address 3) values. This is not correct since it misses the possibility
of BSSID being a wildcard BSSID in which case the Address 1 would not
necessarily match.
Fix this by allowing mac80211 to accept wildcard BSSID in an Action
frame when in AP mode.
Fixes: db8e17324553 ("mac80211: ignore frames between TDLS peers when operating as AP")
Cc: stable@vger.kernel.org
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Just like for CCMP we need to check that for GCMP the fragments
have PNs that increment by one; the spec was updated to fix this
security issue and now has the following text:
The receiver shall discard MSDUs and MMPDUs whose constituent
MPDU PN values are not incrementing in steps of 1.
Adapt the code for CCMP to work for GCMP as well, luckily the
relevant fields already alias each other so no code duplication
is needed (just check the aliasing with BUILD_BUG_ON.)
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Johannes Berg says:
====================
Another small set of fixes:
* stop critical protocol session on disconnect to avoid
it getting stuck
* wext: fix two RTNL message ordering issues
* fix an uninitialized value (found by KASAN)
* fix an out-of-bounds access (also found by KASAN)
* clear connection keys when freeing them in all cases
(IBSS, all other places already did so)
* fix expected throughput unit to get consistent values
* set default TX aggregation timeout to 0 in minstrel
to avoid (really just hide) issues and perform better
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Drivers may need to track which vif is using VHT MU-MIMO.
Move the flag indicationg the ownership of MU_MIMO to
ieee80211_vif.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Provide an interface to the lower level driver to set the VHT
MU-MIMO data. This is needed for example when there is an update
of the group data during low power state, where the management
frame will not be passed to the host at all.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Since the PNs of all the tx keys are now tracked in the public
part of the key struct (with atomic counter), we no longer
need these functions.
dvm and vt665{5,6} are currently the only users of these functions,
so update them accordingly.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Some drivers/devices might want to set the IVs by
themselves (and still let mac80211 generate MMIC).
Specifically, this is needed when the device does
offloading at certain times, and the driver has
to make sure that the IVs of new tx frames (from
the host) are synchronized with IVs that were
potentially used during the offloading.
Similarly to CCMP, move the TX IVs of TKIP keys to the
public part of the key struct, and export a function
to add the IV right into the crypto header.
The public tx_pn field is defined as atomic64, so define
TKIP_PN_TO_IV16/32 helper macros to convert it to iv16/32
when needed.
Since the iv32 used for the p1k cache is taken
directly from the frame, we can safely remove
iv16/32 from being protected by tkip.txlock.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Fix wiphy supported_band access in tx radiotap parsing introduced
in commit 5ec3aed9ba4c ("mac80211: Parse legacy and HT rate in
injected frames"). In particular, info->band is always set to 0
(IEEE80211_BAND_2GHZ) since it has not assigned yet.
This cause a kernel crash on 5GHz only devices.
Move ieee80211_parse_tx_radiotap() after info->band assignment
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The source and destintation addresses in the memcpy arguments
are flipped. Fix that.
Fixes: 23a1f8d44c0b("mac80211: process and save VHT MU-MIMO group frame")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
mpp_path_del() and mesh_path_del() are mostly the same function.
Move common code into a new static function.
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Henning Rogge <henning.rogge@fkie.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Remember the last time when a mpp table entry is used for
rx or tx and remove them after MESH_PATH_EXPIRE time.
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Henning Rogge <henning.rogge@fkie.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Make the mesh_path_del() function remove all mpp table entries
that are proxied by the removed mesh path.
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Henning Rogge <henning.rogge@fkie.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Prepararation for zero-copy A-MSDU support with page fragment SKBs
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
Johannes Berg
Mohammed Shafi Shajakhan
Sara Sharon
Emmanuel Grumbach
Felix Fietkau
Ilan Peer
Luis de Bethencourt
Ben Greear
Sven Eckelmann
Bob Copeland
Jouni Malinen
Arik Nemtsov
Lorenzo Bianconi
David S. Miller
Zhang Shengju
Eliad Peller
Henning Rogge