| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
When using mpls over gre/gre6 setup, rt->rt_gw4 address is not set, the
same for rt->rt_gw_family. Therefore, when rt->rt_gw_family is checked
in mpls_xmit(), neigh_xmit() call is skipped. As a result, such setup
doesn't work anymore.
This issue was found with LTP mpls03 tests.
Fixes: 1550c171935d ("ipv4: Prepare rtable for IPv6 gateway")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the sysctl code the proc_dointvec_minmax() function is often used to
validate the user supplied value between an allowed range. This
function uses the extra1 and extra2 members from struct ctl_table as
minimum and maximum allowed value.
On sysctl handler declaration, in every source file there are some
readonly variables containing just an integer which address is assigned
to the extra1 and extra2 members, so the sysctl range is enforced.
The special values 0, 1 and INT_MAX are very often used as range
boundary, leading duplication of variables like zero=0, one=1,
int_max=INT_MAX in different source files:
$ git grep -E '\.extra[12].*&(zero|one|int_max)' |wc -l
248
Add a const int array containing the most commonly used values, some
macros to refer more easily to the correct array member, and use them
instead of creating a local one for every object file.
This is the bloat-o-meter output comparing the old and new binary
compiled with the default Fedora config:
# scripts/bloat-o-meter -d vmlinux.o.old vmlinux.o
add/remove: 2/2 grow/shrink: 0/2 up/down: 24/-188 (-164)
Data old new delta
sysctl_vals - 12 +12
__kstrtab_sysctl_vals - 12 +12
max 14 10 -4
int_max 16 - -16
one 68 - -68
zero 128 28 -100
Total: Before=20583249, After=20583085, chg -0.00%
[mcroce@redhat.com: tipc: remove two unused variables]
Link: http://lkml.kernel.org/r/20190530091952.4108-1-mcroce@redhat.com
[akpm@linux-foundation.org: fix net/ipv6/sysctl_net_ipv6.c]
[arnd@arndb.de: proc/sysctl: make firmware loader table conditional]
Link: http://lkml.kernel.org/r/20190617130014.1713870-1-arnd@arndb.de
[akpm@linux-foundation.org: fix fs/eventpoll.c]
Link: http://lkml.kernel.org/r/20190430180111.10688-1-mcroce@redhat.com
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Aaron Tomlin <atomlin@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Randy reported that selecting MPLS_ROUTING without PROC_FS breaks
the build, because since commit c1a9d65954c6 ("mpls: fix af_mpls
dependencies"), MPLS_ROUTING selects PROC_SYSCTL, but Kconfig's select
doesn't recursively handle dependencies.
Change the select into a dependency.
Fixes: c1a9d65954c6 ("mpls: fix af_mpls dependencies")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MPLS routing code relies on sysctl to work, so let it select PROC_SYSCTL.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If you configure a route with multiple labels, e.g.
ip route add 10.10.3.0/24 encap mpls 16/100 via 10.10.2.2 dev ens4
A warning is logged:
kernel: [ 130.561819] netlink: 'ip': attribute type 1 has an invalid
length.
This happens because mpls_iptunnel_policy has set the type of
MPLS_IPTUNNEL_DST to fixed size NLA_U32.
Change it to a minimum size.
nla_get_labels() does the remaining validation.
Fixes: e3e4712ec096 ("mpls: ip tunnel support")
Signed-off-by: George Wilkie <gwilkie@vyatta.att-mail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have MODULE_LICENCE("GPL*") inside which was used in the initial
scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We currently have two levels of strict validation:
1) liberal (default)
- undefined (type >= max) & NLA_UNSPEC attributes accepted
- attribute length >= expected accepted
- garbage at end of message accepted
2) strict (opt-in)
- NLA_UNSPEC attributes accepted
- attribute length >= expected accepted
Split out parsing strictness into four different options:
* TRAILING - check that there's no trailing data after parsing
attributes (in message or nested)
* MAXTYPE - reject attrs > max known type
* UNSPEC - reject attributes with NLA_UNSPEC policy entries
* STRICT_ATTRS - strictly validate attribute size
The default for future things should be *everything*.
The current *_strict() is a combination of TRAILING and MAXTYPE,
and is renamed to _deprecated_strict().
The current regular parsing has none of this, and is renamed to
*_parse_deprecated().
Additionally it allows us to selectively set one of the new flags
even on old policies. Notably, the UNSPEC flag could be useful in
this case, since it can be arranged (by filling in the policy) to
not be an incompatible userspace ABI change, but would then going
forward prevent forgetting attribute entries. Similar can apply
to the POLICY flag.
We end up with the following renames:
* nla_parse -> nla_parse_deprecated
* nla_parse_strict -> nla_parse_deprecated_strict
* nlmsg_parse -> nlmsg_parse_deprecated
* nlmsg_parse_strict -> nlmsg_parse_deprecated_strict
* nla_parse_nested -> nla_parse_nested_deprecated
* nla_validate_nested -> nla_validate_nested_deprecated
Using spatch, of course:
@@
expression TB, MAX, HEAD, LEN, POL, EXT;
@@
-nla_parse(TB, MAX, HEAD, LEN, POL, EXT)
+nla_parse_deprecated(TB, MAX, HEAD, LEN, POL, EXT)
@@
expression NLH, HDRLEN, TB, MAX, POL, EXT;
@@
-nlmsg_parse(NLH, HDRLEN, TB, MAX, POL, EXT)
+nlmsg_parse_deprecated(NLH, HDRLEN, TB, MAX, POL, EXT)
@@
expression NLH, HDRLEN, TB, MAX, POL, EXT;
@@
-nlmsg_parse_strict(NLH, HDRLEN, TB, MAX, POL, EXT)
+nlmsg_parse_deprecated_strict(NLH, HDRLEN, TB, MAX, POL, EXT)
@@
expression TB, MAX, NLA, POL, EXT;
@@
-nla_parse_nested(TB, MAX, NLA, POL, EXT)
+nla_parse_nested_deprecated(TB, MAX, NLA, POL, EXT)
@@
expression START, MAX, POL, EXT;
@@
-nla_validate_nested(START, MAX, POL, EXT)
+nla_validate_nested_deprecated(START, MAX, POL, EXT)
@@
expression NLH, HDRLEN, MAX, POL, EXT;
@@
-nlmsg_validate(NLH, HDRLEN, MAX, POL, EXT)
+nlmsg_validate_deprecated(NLH, HDRLEN, MAX, POL, EXT)
For this patch, don't actually add the strict, non-renamed versions
yet so that it breaks compile if I get it wrong.
Also, while at it, make nla_validate and nla_parse go down to a
common __nla_validate_parse() function to avoid code duplication.
Ultimately, this allows us to have very strict validation for every
new caller of nla_parse()/nlmsg_parse() etc as re-introduced in the
next patch, while existing things will continue to work as is.
In effect then, this adds fully strict validation for any new command.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Even if the NLA_F_NESTED flag was introduced more than 11 years ago, most
netlink based interfaces (including recently added ones) are still not
setting it in kernel generated messages. Without the flag, message parsers
not aware of attribute semantics (e.g. wireshark dissector or libmnl's
mnl_nlmsg_fprintf()) cannot recognize nested attributes and won't display
the structure of their contents.
Unfortunately we cannot just add the flag everywhere as there may be
userspace applications which check nlattr::nla_type directly rather than
through a helper masking out the flags. Therefore the patch renames
nla_nest_start() to nla_nest_start_noflag() and introduces nla_nest_start()
as a wrapper adding NLA_F_NESTED. The calls which add NLA_F_NESTED manually
are rewritten to use nla_nest_start().
Except for changes in include/net/netlink.h, the patch was generated using
this semantic patch:
@@ expression E1, E2; @@
-nla_nest_start(E1, E2)
+nla_nest_start_noflag(E1, E2)
@@ expression E1, E2; @@
-nla_nest_start_noflag(E1, E2 | NLA_F_NESTED)
+nla_nest_start(E1, E2)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The header contains rtnh_ macros so rename the file accordingly.
Allows a later patch to use the nexthop.h name for the new
nexthop code.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for an IPv6 gateway to rtable. Since a gateway is either
IPv4 or IPv6, make it a union with rt_gw4 where rt_gw_family decides
which address is in use.
When dumping the route data, encode an ipv6 nexthop using RTA_VIA.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To allow the gateway to be either an IPv4 or IPv6 address, remove
rt_uses_gateway from rtable and replace with rt_gw_family. If
rt_gw_family is set it implies rt_uses_gateway. Rename rt_gateway
to rt_gw4 to represent the IPv4 version.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The number of stubs is growing and has nothing to do with addrconf.
Move the definition of the stubs to a separate header file and update
users. In the move, drop the vxlan specific comment before ipv6_stub.
Code move only; no functional change intended.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for 6PE (RFC 4798) which uses IPv4-mapped IPv6
nexthop to connect IPv6 islands over IPv4 only MPLS network core.
Prior to this fix, to find the link-layer destination mac address, 6PE
enabled host/router was sending IPv6 ND requests for IPv4-mapped IPv6
nexthop address over the interface facing the IPv4 only core which
wouldn't success as the core is IPv6 free.
This fix changes that behavior on 6PE host to treat the nexthop as IPv4
address and send ARP requests whenever the next-hop address is an
IPv4-mapped IPv6 address.
Below topology illustrates the issue and how the patch addresses it.
abcd::1.1.1.1 (lo) abcd::2.2.2.2 (lo)
R0 (PE/host)------------------------R1--------------------------------R2 (PE/host)
<--- IPv4 MPLS core ---> <------ IPv4 MPLS core -------->
eth1 eth2 eth3 eth4
172.18.0.10 172.18.0.11 172.19.0.11 172.19.0.12
ffff::172.18.0.10 ffff::172.19.0.12
<------------------IPv6 MPLS tunnel ---------------------->
R0 and R2 act as 6PE routers of IPv6 islands. R1 is IPv4 only with MPLS tunnels
between R0,R1 and R1,R2.
docker exec r0 ip -f inet6 route add abcd::2.2.2.2/128 nexthop encap mpls 100 via ::ffff:172.18.0.11 dev eth1
docker exec r2 ip -f inet6 route add abcd::1.1.1.1/128 nexthop encap mpls 200 via ::ffff:172.19.0.11 dev eth4
docker exec r1 ip -f mpls route add 100 via inet 172.19.0.12 dev eth3
docker exec r1 ip -f mpls route add 200 via inet 172.18.0.10 dev eth2
With the change, when R0 sends an IPv6 packet over MPLS tunnel to abcd::2.2.2.2,
using ::ffff:172.18.0.11 as the nexthop, it does neighbor discovery for
172.18.18.0.11.
Signed-off-by: Vinay K Nallamothu <nvinay@juniper.net>
Tested-by: Avinash Lingala <ar977m@att.com>
Tested-by: Aravind Srinivas Srinivasa Prabhakar <aprabh@juniper.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
MPLS does not support nexthops with an MPLS address family.
Specifically, it does not handle RTA_GATEWAY attribute. Make it
clear by returning an error.
Fixes: 03c0566542f4c ("mpls: Netlink commands to add, remove, and dump routes")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
instance = alloc(sizeof(struct foo) + count * sizeof(struct boo));
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = alloc(struct_size(instance, entry, count));
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make RTM_GETNETCONF's doit handler use strict checks when
NETLINK_F_STRICT_CHK is set.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make RTM_GETROUTE's doit handler use strict checks when
NETLINK_F_STRICT_CHK is set.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update the dump request parsing in MPLS for the non-INET case to
enable kernel side filtering. If INET is disabled the only filters
that make sense for MPLS are protocol and nexthop device.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update parsing of route dump request to enable kernel side filtering.
Allow filtering results by protocol (e.g., which routing daemon installed
the route), route type (e.g., unicast), table id and nexthop device. These
amount to the low hanging fruit, yet a huge improvement, for dumping
routes.
ip_valid_fib_dump_req is called with RTNL held, so __dev_get_by_index can
be used to look up the device index without taking a reference. From
there filter->dev is only used during dump loops with the lock still held.
Set NLM_F_DUMP_FILTERED in the answer_flags so the user knows the results
have been filtered should no entries be returned.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement kernel side filtering of routes by egress device index and
protocol. MPLS uses only a single table and route type.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add struct fib_dump_filter for options on limiting which routes are
returned in a dump request. The current list is table id, protocol,
route type, rtm_flags and nexthop device index. struct net is needed
to lookup the net_device from the index.
Declare the filter for each route dump handler and plumb the new
arguments from dump handlers to ip_valid_fib_dump_req.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Without CONFIG_INET enabled compiles fail with:
net/mpls/af_mpls.o: In function `mpls_dump_routes':
af_mpls.c:(.text+0xed0): undefined reference to `ip_valid_fib_dump_req'
The preference is for MPLS to use the same handler as ipv4 and ipv6
to allow consistency when doing a dump for AF_UNSPEC which walks
all address families invoking the route dump handler. If INET is
disabled then fallback to an MPLS version which can be tighter on
the data checks.
Fixes: e8ba330ac0c5 ("rtnetlink: Update fib dumps for strict data checking")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update inet_netconf_dump_devconf, inet6_netconf_dump_devconf, and
mpls_netconf_dump_devconf for strict data checking. If the flag is set,
the dump request is expected to have an netconfmsg struct as the header.
The struct only has the family member and no attributes can be appended.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Christian Brauner <christian@brauner.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add helper to check netlink message for route dumps. If the strict flag
is set the dump request is expected to have an rtmsg struct as the header.
All elements of the struct are expected to be 0 with the exception of
rtm_flags (which is used by both ipv4 and ipv6 dumps) and no attributes
can be appended. rtm_flags can only have RTM_F_CLONED and RTM_F_PREFIX
set.
Update inet_dump_fib, inet6_dump_fib, mpls_dump_routes, ipmr_rtm_dumproute,
and ip6mr_rtm_dumproute to call this helper if strict data checking is
enabled.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure extack is passed to nlmsg_parse where easy to do so.
Most of these are dump handlers and leveraging the extack in
the netlink_callback.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Christian Brauner <christian@brauner.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Summary:
This appears to be necessary and sufficient change to enable `MPLS` on
`ip6gre` tunnels (RFC4023).
This diff allows IP6GRE devices to be recognized by MPLS kernel module
and hence user can configure interface to accept packets with mpls
headers as well setup mpls routes on them.
Test Plan:
Test plan consists of multiple containers connected via GRE-V6 tunnel.
Then carrying out testing steps as below.
- Carry out necessary sysctl settings on all containers
```
sysctl -w net.mpls.platform_labels=65536
sysctl -w net.mpls.ip_ttl_propagate=1
sysctl -w net.mpls.conf.lo.input=1
```
- Establish IP6GRE tunnels
```
ip -6 tunnel add name if_1_2_1 mode ip6gre \
local 2401:db00:21:6048:feed:0::1 \
remote 2401:db00:21:6048:feed:0::2 key 1
ip link set dev if_1_2_1 up
sysctl -w net.mpls.conf.if_1_2_1.input=1
ip -4 addr add 169.254.0.2/31 dev if_1_2_1 scope link
ip -6 tunnel add name if_1_3_1 mode ip6gre \
local 2401:db00:21:6048:feed:0::1 \
remote 2401:db00:21:6048:feed:0::3 key 1
ip link set dev if_1_3_1 up
sysctl -w net.mpls.conf.if_1_3_1.input=1
ip -4 addr add 169.254.0.4/31 dev if_1_3_1 scope link
```
- Install MPLS encap rules on node-1 towards node-2
```
ip route add 192.168.0.11/32 nexthop encap mpls 32/64 \
via inet 169.254.0.3 dev if_1_2_1
```
- Install MPLS forwarding rules on node-2 and node-3
```
// node2
ip -f mpls route add 32 via inet 169.254.0.7 dev if_2_4_1
// node3
ip -f mpls route add 64 via inet 169.254.0.12 dev if_4_3_1
```
- Ping 192.168.0.11 (node4) from 192.168.0.1 (node1) (where routing
towards 192.168.0.1 is via IP route directly towards node1 from node4)
```
ping 192.168.0.11
```
- tcpdump on interface to capture ping packets wrapped within MPLS
header which inturn wrapped within IP6GRE header
```
16:43:41.121073 IP6
2401:db00:21:6048:feed::1 > 2401:db00:21:6048:feed::2:
DSTOPT GREv0, key=0x1, length 100:
MPLS (label 32, exp 0, ttl 255) (label 64, exp 0, [S], ttl 255)
IP 192.168.0.1 > 192.168.0.11:
ICMP echo request, id 1208, seq 45, length 64
0x0000: 6000 2cdb 006c 3c3f 2401 db00 0021 6048 `.,..l<?$....!`H
0x0010: feed 0000 0000 0001 2401 db00 0021 6048 ........$....!`H
0x0020: feed 0000 0000 0002 2f00 0401 0401 0100 ......../.......
0x0030: 2000 8847 0000 0001 0002 00ff 0004 01ff ...G............
0x0040: 4500 0054 3280 4000 ff01 c7cb c0a8 0001 E..T2.@.........
0x0050: c0a8 000b 0800 a8d7 04b8 002d 2d3c a05b ...........--<.[
0x0060: 0000 0000 bcd8 0100 0000 0000 1011 1213 ................
0x0070: 1415 1617 1819 1a1b 1c1d 1e1f 2021 2223 .............!"#
0x0080: 2425 2627 2829 2a2b 2c2d 2e2f 3031 3233 $%&'()*+,-./0123
0x0090: 3435 3637 4567
```
Signed-off-by: Saif Hasan <has@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If you take a GSO skb, and split it into packets, will the network
length (L3 headers + L4 headers + payload) of those packets be small
enough to fit within a given MTU?
skb_gso_validate_mtu gives you the answer to that question. However,
we recently added to add a way to validate the MAC length of a split GSO
skb (L2+L3+L4+payload), and the names get confusing, so rename
skb_gso_validate_mtu to skb_gso_validate_network_len
Signed-off-by: Daniel Axtens <dja@axtens.net>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mpls_label_ok() validates that the 'platform_label' array index from a
userspace netlink message payload is valid. Under speculation the
mpls_label_ok() result may not resolve in the CPU pipeline until after
the index is used to access an array element. Sanitize the index to zero
to prevent userspace-controlled arbitrary out-of-bounds speculation, a
precursor for a speculative execution side channel vulnerability.
Cc: <stable@vger.kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
all of these can be compiled as a module, so use new
_module version to make sure module can no longer be removed
while callback/dump is in use.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When af_mpls is built-in but the tunnel support is a module,
we get a link failure:
net/mpls/af_mpls.o: In function `mpls_init':
af_mpls.c:(.init.text+0xdc): undefined reference to `ip_tunnel_encap_add_ops'
This adds a Kconfig statement to prevent the broken
configuration and force mpls to be a module as well in
this case.
Fixes: bdc476413dcd ("ip_tunnel: add mpls over gre support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Amine Kherbouche <amine.kherbouche@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function ipgre_mpls_encap_hlen is local to the source and
does not need to be in global scope, so make it static.
Cleans up sparse warning:
symbol 'ipgre_mpls_encap_hlen' was not declared. Should it be static?
Fixes: bdc476413dcdb ("ip_tunnel: add mpls over gre support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This commit introduces the MPLSoGRE support (RFC 4023), using ip tunnel
API by simply adding ipgre_tunnel_encap_(add|del)_mpls_ops() and the new
tunnel type TUNNEL_ENCAP_MPLS.
Signed-off-by: Amine Kherbouche <amine.kherbouche@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change allows us to later indicate to rtnetlink core that certain
doit functions should be called without acquiring rtnl_mutex.
This change should have no effect, we simply replace the last (now
unused) calcit argument with the new flag.
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the below warning generated by static checker:
net/mpls/af_mpls.c:2111 mpls_getroute()
error: uninitialized symbol 'in_label'."
Fixes: 397fc9e5cefe ("mpls: route get support")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
fix rtm policy name typo in mpls_getroute and also remove
export of rtm_ipv4_policy
Fixes: 397fc9e5cefe ("mpls: route get support")
Reported-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds RTM_GETROUTE doit handler for mpls routes.
Input:
RTA_DST - input label
RTA_NEWDST - labels in packet for multipath selection
By default the getroute handler returns matched
nexthop label, via and oif
With RTM_F_FIB_MATCH flag, full matched route is
returned.
example (with patched iproute2):
$ip -f mpls route show
101
nexthop as to 102/103 via inet 172.16.2.2 dev virt1-2
nexthop as to 302/303 via inet 172.16.12.2 dev virt1-12
201
nexthop as to 202/203 via inet6 2001:db8:2::2 dev virt1-2
nexthop as to 402/403 via inet6 2001:db8:12::2 dev virt1-12
$ip -f mpls route get 103
RTNETLINK answers: Network is unreachable
$ip -f mpls route get 101
101 as to 102/103 via inet 172.16.2.2 dev virt1-2
$ip -f mpls route get as to 302/303 101
101 as to 302/303 via inet 172.16.12.2 dev virt1-12
$ip -f mpls route get fibmatch 103
RTNETLINK answers: Network is unreachable
$ip -f mpls route get fibmatch 101
101
nexthop as to 102/103 via inet 172.16.2.2 dev virt1-2
nexthop as to 302/303 via inet 172.16.12.2 dev virt1-12
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Just some simple overlapping changes in marvell PHY driver
and the DSA core code.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
recent fixes to use WRITE_ONCE for nh_flags on link up,
accidently ended up leaving the deadflags on a nh. This patch
fixes the WRITE_ONCE to use freshly evaluated nh_flags.
Fixes: 39eb8cd17588 ("net: mpls: rt_nhn_alive and nh_flags should be accessed using READ_ONCE")
Reported-by: Satish Ashok <sashok@cumulusnetworks.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
err is initialized to EINVAL and not used before it is set again.
Remove the unnecessary initialization.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
nla_get_via is only used in af_mpls.c. Remove declaration from internal.h
and move up in af_mpls.c before first use. Code move only; no
functional change intended.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add error messages for failures in adding and deleting mpls routes.
This covers most of the annoying EINVAL errors.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mpls_route_add and mpls_route_del have the same checks on the label.
Move to a helper. Avoid duplicate extack messages in the next patch.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fill in extack for errors in build_state for mpls lwt encap including
passing extack to nla_get_labels and adding error messages for failures
in it.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pass extack arg down to lwtunnel_build_state and the build_state callbacks.
Add messages for failures in lwtunnel_build_state, and add the extarg to
nla_parse where possible in the build_state callbacks.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Alexey Kodanev
Matteo Croce
George Wilkie
Thomas Gleixner
Johannes Berg
Michal Kubecek
David Ahern
Vinay K Nallamothu
David S. Miller
Gustavo A. R. Silva
Jakub Kicinski
Saif Hasan
Stephen Hemminger
Daniel Axtens
Dan Williams
Florian Westphal
Greg Kroah-Hartman
Arnd Bergmann
Colin Ian King
Amine Kherbouche
Roopa Prabhu