| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Currently, we have option to configure MTU of UDP media. The configured
MTU takes effect on the links going up after that moment. I.e, a user
has to reset bearer to have new value applied across its links. This is
confusing and disturbing on a running cluster.
We now introduce the functionality to change the default UDP bearer MTU
in struct tipc_bearer. Additionally, the links are updated dynamically,
without any need for a reset, when bearer value is changed. We leverage
the existing per-link functionality and the design being symetrical to
the confguration of link tolerance.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: GhantaKrishnamurthy MohanKrishna <mohan.krishna.ghanta.krishnamurthy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In previous commit, we changed the default emulated MTU for UDP bearers
to 14k.
This commit adds the functionality to set/change the default value
by configuring new MTU for UDP media. UDP bearer(s) have to be disabled
and enabled back for the new MTU to take effect.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: GhantaKrishnamurthy MohanKrishna <mohan.krishna.ghanta.krishnamurthy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Selecting and explicitly configuring a TIPC node identity may be
unwanted in some cases.
In this commit we introduce a default setting if the identity has not
been set at the moment the first bearer is enabled. We do this by
using a raw copy of a unique identifier from the used interface: MAC
address in the case of an L2 bearer, IPv4/IPv6 address in the case
of a UDP bearer.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a 32-bit node address is generated from a 128-bit identifier,
there is a risk of collisions which must be discovered and handled.
We do this as follows:
- We don't apply the generated address immediately to the node, but do
instead initiate a 1 sec trial period to allow other cluster members
to discover and handle such collisions.
- During the trial period the node periodically sends out a new type
of message, DSC_TRIAL_MSG, using broadcast or emulated broadcast,
to all the other nodes in the cluster.
- When a node is receiving such a message, it must check that the
presented 32-bit identifier either is unused, or was used by the very
same peer in a previous session. In both cases it accepts the request
by not responding to it.
- If it finds that the same node has been up before using a different
address, it responds with a DSC_TRIAL_FAIL_MSG containing that
address.
- If it finds that the address has already been taken by some other
node, it generates a new, unused address and returns it to the
requester.
- During the trial period the requesting node must always be prepared
to accept a failure message, i.e., a message where a peer suggests a
different (or equal) address to the one tried. In those cases it
must apply the suggested value as trial address and restart the trial
period.
This algorithm ensures that in the vast majority of cases a node will
have the same address before and after a reboot. If a legacy user
configures the address explicitly, there will be no trial period and
messages, so this protocol addition is completely backwards compatible.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Nominally, TIPC organizes network nodes into a three-level network
hierarchy consisting of the levels 'zone', 'cluster' and 'node'. This
hierarchy is reflected in the node address format, - it is sub-divided
into an 8-bit zone id, and 12 bit cluster id, and a 12-bit node id.
However, the 'zone' and 'cluster' levels have in reality never been
fully implemented,and never will be. The result of this has been
that the first 20 bits the node identity structure have been wasted,
and the usable node identity range within a cluster has been limited
to 12 bits. This is starting to become a problem.
In the following commits, we will need to be able to connect between
nodes which are using the whole 32-bit value space of the node address.
We therefore remove the restrictions on which values can be assigned
to node identity, -it is from now on only a 32-bit integer with no
assumed internal structure.
Isolation between clusters is now achieved only by setting different
values for the 'network id' field used during neighbor discovery, in
practice leading to the latter becoming the new cluster identity.
The rules for accepting discovery requests/responses from neighboring
nodes now become:
- If the user is using legacy address format on both peers, reception
of discovery messages is subject to the legacy lookup domain check
in addition to the cluster id check.
- Otherwise, the discovery request/response is always accepted, provided
both peers have the same network id.
This secures backwards compatibility for users who have been using zone
or cluster identities as cluster separators, instead of the intended
'network id'.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To facilitate the coming changes in the neighbor discovery functionality
we make some renaming and refactoring of that code. The functional changes
in this commit are trivial, e.g., that we move the message sending call in
tipc_disc_timeout() outside the spinlock protected region.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As a preparation for the next commits we try to reduce the footprint of
the function tipc_enable_bearer(), while hopefully making is simpler to
follow.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
Currently, the default link tolerance set in struct tipc_bearer only
has effect on links going up after that moment. I.e., a user has to
reset all the node's links across that bearer to have the new value
applied. This is too limiting and disturbing on a running cluster to
be useful.
We now change this so that also already existing links are updated
dynamically, without any need for a reset, when the bearer value is
changed. We leverage the already existing per-link functionality
for this to achieve the wanted effect.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce __tipc_nl_media_set() which doesn't hold RTNL lock.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce __tipc_nl_bearer_set() which doesn't holding RTNL lock.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce __tipc_nl_bearer_enable() which doesn't hold RTNL lock.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce __tipc_nl_bearer_disable() which doesn't hold RTNL lock.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix memory leak in tipc_enable_bearer() if enable_media() fails, and
cleanup with bearer_disable() if tipc_mon_create() fails.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tommi Rantala <tommi.t.rantala@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The net device is already stored in the 'net' variable, so no need to call
dev_net() again.
Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Three cases of simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For a bond slave device as a tipc bearer, the dev represents the bond
interface and orig_dev represents the slave in tipc_l2_rcv_msg().
Since we decode the tipc_ptr from bonding device (dev), we fail to
find the bearer and thus tipc links are not established.
In this commit, we register the tipc protocol callback per device and
look for tipc bearer from both the devices.
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the broadcast send link after 100 attempts has failed to
transfer a packet to all peers, we consider it stale, and reset
it. Thereafter it needs to re-synchronize with the peers, something
currently done by just resetting and re-establishing all links to
all peers. This has turned out to be overkill, with potentially
unwanted consequences for the remaining cluster.
A closer analysis reveals that this can be done much simpler. When
this kind of failure happens, for reasons that may lie outside the
TIPC protocol, it is typically only one peer which is failing to
receive and acknowledge packets. It is hence sufficient to identify
and reset the links only to that peer to resolve the situation, without
having to reset the broadcast link at all. This solution entails a much
lower risk of negative consequences for the own node as well as for
the overall cluster.
We implement this change in this commit.
Reviewed-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On L2 bearers, the TIPC broadcast function is sending out packets using
the corresponding L2 broadcast address. At reception, we filter such
packets under the assumption that they will also be delivered as
broadcast packets.
This assumption doesn't always hold true. Under high load, we have seen
that a switch may convert the destination address and deliver the packet
as a PACKET_MULTICAST, something leading to inadvertently dropped
packets and a stale and reset broadcast link.
We fix this by extending the reception filtering to accept packets of
type PACKET_MULTICAST.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is an add-on to the previous patch that passes the extended ACK
structure where it's already available by existing genl_info or extack
function arguments.
This was done with this spatch (with some manual adjustment of
indentation):
@@
expression A, B, C, D, E;
identifier fn, info;
@@
fn(..., struct genl_info *info, ...) {
...
-nlmsg_parse(A, B, C, D, E, NULL)
+nlmsg_parse(A, B, C, D, E, info->extack)
...
}
@@
expression A, B, C, D, E;
identifier fn, info;
@@
fn(..., struct genl_info *info, ...) {
<...
-nla_parse_nested(A, B, C, D, NULL)
+nla_parse_nested(A, B, C, D, info->extack)
...>
}
@@
expression A, B, C, D, E;
identifier fn, extack;
@@
fn(..., struct netlink_ext_ack *extack, ...) {
<...
-nlmsg_parse(A, B, C, D, E, NULL)
+nlmsg_parse(A, B, C, D, E, extack)
...>
}
@@
expression A, B, C, D, E;
identifier fn, extack;
@@
fn(..., struct netlink_ext_ack *extack, ...) {
<...
-nla_parse(A, B, C, D, E, NULL)
+nla_parse(A, B, C, D, E, extack)
...>
}
@@
expression A, B, C, D, E;
identifier fn, extack;
@@
fn(..., struct netlink_ext_ack *extack, ...) {
...
-nlmsg_parse(A, B, C, D, E, NULL)
+nlmsg_parse(A, B, C, D, E, extack)
...
}
@@
expression A, B, C, D;
identifier fn, extack;
@@
fn(..., struct netlink_ext_ack *extack, ...) {
<...
-nla_parse_nested(A, B, C, D, NULL)
+nla_parse_nested(A, B, C, D, extack)
...>
}
@@
expression A, B, C, D;
identifier fn, extack;
@@
fn(..., struct netlink_ext_ack *extack, ...) {
<...
-nlmsg_validate(A, B, C, D, NULL)
+nlmsg_validate(A, B, C, D, extack)
...>
}
@@
expression A, B, C, D;
identifier fn, extack;
@@
fn(..., struct netlink_ext_ack *extack, ...) {
<...
-nla_validate(A, B, C, D, NULL)
+nla_validate(A, B, C, D, extack)
...>
}
@@
expression A, B, C;
identifier fn, extack;
@@
fn(..., struct netlink_ext_ack *extack, ...) {
<...
-nla_validate_nested(A, B, C, NULL)
+nla_validate_nested(A, B, C, extack)
...>
}
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pass the new extended ACK reporting struct to all of the generic
netlink parsing functions. For now, pass NULL in almost all callers
(except for some in the core.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As a preparation for the 'replicast' functionality we are going to
introduce in the next commits, we need the broadcast base structure to
store whether bearer broadcast is available at all from the currently
used bearer or bearers.
We do this by adding a new function tipc_bearer_bcast_support() to
the bearer layer, and letting the bearer selection function in
bcast.c use this to give a new boolean field, 'bcast_support' the
appropriate value.
Reviewed-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Qian Zhang (张谦) reported a potential socket buffer overflow in
tipc_msg_build() which is also known as CVE-2016-8632: due to
insufficient checks, a buffer overflow can occur if MTU is too short for
even tipc headers. As anyone can set device MTU in a user/net namespace,
this issue can be abused by a regular user.
As agreed in the discussion on Ben Hutchings' original patch, we should
check the MTU at the moment a bearer is attached rather than for each
processed packet. We also need to repeat the check when bearer MTU is
adjusted to new device MTU. UDP case also needs a check to avoid
overflow when calculating bearer MTU.
Fixes: b97bf3fd8f6a ("[TIPC] Initial merge")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reported-by: Qian Zhang (张谦) <zhangqian-c@360.cn>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add UDP bearer options to netlink bearer get message. This is used by
the tipc user space tool to display UDP options.
The UDP bearer information is passed using either a sockaddr_in or
sockaddr_in6 structs. This means the user space receiver should
intermediately store the retrieved data in a large enough struct
(sockaddr_strage) before casting to the proper IP version type.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch introduces UDP replicast. A concept where we emulate
multicast by sending multiple unicast messages to configured peers.
The purpose of replicast is mainly to be able to use TIPC in cloud
environments where IP multicast is disabled. Using replicas to unicast
multicast messages is costly as we have to copy each skb and send the
copies individually.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use kfree_skb() instead of kfree() to free sk_buff.
Fixes: 0d051bf93c06 ("tipc: make bearer packet filtering generic")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit 5b7066c3dd24 ("tipc: stricter filtering of packets in bearer
layer") we introduced a method of filtering out messages while a bearer
is being reset, to avoid that links may be re-created and come back in
working state while we are still in the process of shutting them down.
This solution works well, but is limited to only work with L2 media, which
is insufficient with the increasing use of UDP as carrier media.
We now replace this solution with a more generic one, by introducing a
new flag "up" in the generic struct tipc_bearer. This field will be set
and reset at the same locations as with the previous solution, while
the packet filtering is moved to the generic code for the sending side.
On the receiving side, the filtering is still done in media specific
code, but now including the UDP bearer.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce a new function to get the bearer name from
its id. This is used in subsequent commit.
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In this commit, we introduce defines for tipc address size,
offset and mask specification for Zone.Cluster.Node.
There is no functional change in this commit.
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Just several instances of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In test situations with many nodes and a heavily stressed system we have
observed that the transmission broadcast link may fail due to an
excessive number of retransmissions of the same packet. In such
situations we need to reset all unicast links to all peers, in order to
reset and re-synchronize the broadcast link.
In this commit, we add a new function tipc_bearer_reset_all() to be used
in such situations. The function scans across all bearers and resets all
their pertaining links.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several cases of overlapping changes, except the packet scheduler
conflicts which deal with the addition of the free list parameter
to qdisc_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When run tipcTS&tipcTC test suite, the following complaint appears:
[ 56.926168] ===============================
[ 56.926169] [ INFO: suspicious RCU usage. ]
[ 56.926171] 4.7.0-rc1+ #160 Not tainted
[ 56.926173] -------------------------------
[ 56.926174] net/tipc/bearer.c:408 suspicious rcu_dereference_protected() usage!
[ 56.926175]
[ 56.926175] other info that might help us debug this:
[ 56.926175]
[ 56.926177]
[ 56.926177] rcu_scheduler_active = 1, debug_locks = 1
[ 56.926179] 3 locks held by swapper/4/0:
[ 56.926180] #0: (((&req->timer))){+.-...}, at: [<ffffffff810e79b5>] call_timer_fn+0x5/0x340
[ 56.926203] #1: (&(&req->lock)->rlock){+.-...}, at: [<ffffffffa000c29b>] disc_timeout+0x1b/0xd0 [tipc]
[ 56.926212] #2: (rcu_read_lock){......}, at: [<ffffffffa00055e0>] tipc_bearer_xmit_skb+0xb0/0x2e0 [tipc]
[ 56.926218]
[ 56.926218] stack backtrace:
[ 56.926221] CPU: 4 PID: 0 Comm: swapper/4 Not tainted 4.7.0-rc1+ #160
[ 56.926222] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2007
[ 56.926224] 0000000000000000 ffff880016803d28 ffffffff813c4423 ffff8800154252c0
[ 56.926227] 0000000000000001 ffff880016803d58 ffffffff810b7512 ffff8800124d8120
[ 56.926230] ffff880013f8a160 ffff8800132b5ccc ffff8800124d8120 ffff880016803d88
[ 56.926234] Call Trace:
[ 56.926235] <IRQ> [<ffffffff813c4423>] dump_stack+0x67/0x94
[ 56.926250] [<ffffffff810b7512>] lockdep_rcu_suspicious+0xe2/0x120
[ 56.926256] [<ffffffffa00051f1>] tipc_l2_send_msg+0x131/0x1c0 [tipc]
[ 56.926261] [<ffffffffa000567c>] tipc_bearer_xmit_skb+0x14c/0x2e0 [tipc]
[ 56.926266] [<ffffffffa00055e0>] ? tipc_bearer_xmit_skb+0xb0/0x2e0 [tipc]
[ 56.926273] [<ffffffffa000c280>] ? tipc_disc_init_msg+0x1f0/0x1f0 [tipc]
[ 56.926278] [<ffffffffa000c280>] ? tipc_disc_init_msg+0x1f0/0x1f0 [tipc]
[ 56.926283] [<ffffffffa000c2d6>] disc_timeout+0x56/0xd0 [tipc]
[ 56.926288] [<ffffffff810e7a68>] call_timer_fn+0xb8/0x340
[ 56.926291] [<ffffffff810e79b5>] ? call_timer_fn+0x5/0x340
[ 56.926296] [<ffffffffa000c280>] ? tipc_disc_init_msg+0x1f0/0x1f0 [tipc]
[ 56.926300] [<ffffffff810e8f4a>] run_timer_softirq+0x23a/0x390
[ 56.926306] [<ffffffff810f89ff>] ? clockevents_program_event+0x7f/0x130
[ 56.926316] [<ffffffff819727c3>] __do_softirq+0xc3/0x4a2
[ 56.926323] [<ffffffff8106ba5a>] irq_exit+0x8a/0xb0
[ 56.926327] [<ffffffff81972456>] smp_apic_timer_interrupt+0x46/0x60
[ 56.926331] [<ffffffff81970a49>] apic_timer_interrupt+0x89/0x90
[ 56.926333] <EOI> [<ffffffff81027fda>] ? default_idle+0x2a/0x1a0
[ 56.926340] [<ffffffff81027fd8>] ? default_idle+0x28/0x1a0
[ 56.926342] [<ffffffff810289cf>] arch_cpu_idle+0xf/0x20
[ 56.926345] [<ffffffff810adf0f>] default_idle_call+0x2f/0x50
[ 56.926347] [<ffffffff810ae145>] cpu_startup_entry+0x215/0x3e0
[ 56.926353] [<ffffffff81040ad9>] start_secondary+0xf9/0x100
The warning appears as rtnl_dereference() is wrongly used in
tipc_l2_send_msg() under RCU read lock protection. Instead the proper
usage should be that rcu_dereference_rtnl() is called here.
Fixes: 5b7066c3dd24 ("tipc: stricter filtering of packets in bearer layer")
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TIPC based clusters are by default set up with full-mesh link
connectivity between all nodes. Those links are expected to provide
a short failure detection time, by default set to 1500 ms. Because
of this, the background load for neighbor monitoring in an N-node
cluster increases with a factor N on each node, while the overall
monitoring traffic through the network infrastructure increases at
a ~(N * (N - 1)) rate. Experience has shown that such clusters don't
scale well beyond ~100 nodes unless we significantly increase failure
discovery tolerance.
This commit introduces a framework and an algorithm that drastically
reduces this background load, while basically maintaining the original
failure detection times across the whole cluster. Using this algorithm,
background load will now grow at a rate of ~(2 * sqrt(N)) per node, and
at ~(2 * N * sqrt(N)) in traffic overhead. As an example, each node will
now have to actively monitor 38 neighbors in a 400-node cluster, instead
of as before 399.
This "Overlapping Ring Supervision Algorithm" is completely distributed
and employs no centralized or coordinated state. It goes as follows:
- Each node makes up a linearly ascending, circular list of all its N
known neighbors, based on their TIPC node identity. This algorithm
must be the same on all nodes.
- The node then selects the next M = sqrt(N) - 1 nodes downstream from
itself in the list, and chooses to actively monitor those. This is
called its "local monitoring domain".
- It creates a domain record describing the monitoring domain, and
piggy-backs this in the data area of all neighbor monitoring messages
(LINK_PROTOCOL/STATE) leaving that node. This means that all nodes in
the cluster eventually (default within 400 ms) will learn about
its monitoring domain.
- Whenever a node discovers a change in its local domain, e.g., a node
has been added or has gone down, it creates and sends out a new
version of its node record to inform all neighbors about the change.
- A node receiving a domain record from anybody outside its local domain
matches this against its own list (which may not look the same), and
chooses to not actively monitor those members of the received domain
record that are also present in its own list. Instead, it relies on
indications from the direct monitoring nodes if an indirectly
monitored node has gone up or down. If a node is indicated lost, the
receiving node temporarily activates its own direct monitoring towards
that node in order to confirm, or not, that it is actually gone.
- Since each node is actively monitoring sqrt(N) downstream neighbors,
each node is also actively monitored by the same number of upstream
neighbors. This means that all non-direct monitoring nodes normally
will receive sqrt(N) indications that a node is gone.
- A major drawback with ring monitoring is how it handles failures that
cause massive network partitionings. If both a lost node and all its
direct monitoring neighbors are inside the lost partition, the nodes in
the remaining partition will never receive indications about the loss.
To overcome this, each node also chooses to actively monitor some
nodes outside its local domain. Those nodes are called remote domain
"heads", and are selected in such a way that no node in the cluster
will be more than two direct monitoring hops away. Because of this,
each node, apart from monitoring the member of its local domain, will
also typically monitor sqrt(N) remote head nodes.
- As an optimization, local list status, domain status and domain
records are marked with a generation number. This saves senders from
unnecessarily conveying unaltered domain records, and receivers from
performing unneeded re-adaptations of their node monitoring list, such
as re-assigning domain heads.
- As a measure of caution we have added the possibility to disable the
new algorithm through configuration. We do this by keeping a threshold
value for the cluster size; a cluster that grows beyond this value
will switch from full-mesh to ring monitoring, and vice versa when
it shrinks below the value. This means that if the threshold is set to
a value larger than any anticipated cluster size (default size is 32)
the new algorithm is effectively disabled. A patch set for altering the
threshold value and for listing the table contents will follow shortly.
- This change is fully backwards compatible.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Resetting a bearer/interface, with the consequence of resetting all its
pertaining links, is not an atomic action. This becomes particularly
evident in very large clusters, where a lot of traffic may happen on the
remaining links while we are busy shutting them down. In extreme cases,
we may even see links being re-created and re-established before we are
finished with the job.
To solve this, we now introduce a solution where we temporarily detach
the bearer from the interface when the bearer is reset. This inhibits
all packet reception, while sending still is possible. For the latter,
we use the fact that the device's user pointer now is zero to filter out
which packets can be sent during this situation; i.e., outgoing RESET
messages only. This filtering serves to speed up the neighbors'
detection of the loss event, and saves us from unnecessary probing.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When enabling a bearer we create a 'neigbor discoverer' instance by
calling the function tipc_disc_create() before the bearer is actually
registered in the list of enabled bearers. Because of this, the very
first discovery broadcast message, created by the mentioned function,
is lost, since it cannot find any valid bearer to use. Furthermore,
the used send function, tipc_bearer_xmit_skb() does not free the given
buffer when it cannot find a bearer, resulting in the leak of exactly
one send buffer each time a bearer is enabled.
This commit fixes this problem by introducing two changes:
1) Instead of attemting to send the discovery message directly, we let
tipc_disc_create() return the discovery buffer to the calling
function, tipc_enable_bearer(), so that the latter can send it
when the enabling sequence is finished.
2) In tipc_bearer_xmit_skb(), as well as in the two other transmit
functions at the bearer layer, we now free the indicated buffer or
buffer chain when a valid bearer cannot be found.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make the c files less cluttered and enable netlink attributes to be
shared between files.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The number of variables with Hungarian notation (l_ptr, n_ptr etc.)
has been significantly reduced over the last couple of years.
We now root out the last traces of this practice.
There are no functional changes in this commit.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After the previous changes in this series, we can now remove some
unused code and structures, both in the broadcast, link aggregation
and link code.
There are no functional changes in this commit.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since all packet transmitters (link, bcast, discovery) are now sending
consumable buffer clones to the bearer layer, we can remove the
redundant buffer cloning that is perfomed in the lower level functions
tipc_l2_send_msg() and tipc_udp_send_msg().
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The neighbor discovery function currently uses the function
tipc_bearer_send() for transmitting packets, assuming that the
sent buffers are not consumed by the called function.
We want to change this, in order to avoid unnecessary buffer cloning
elswhere in the code.
This commit introduces a new function tipc_bearer_skb() which consumes
the sent buffers, and let the discoverer functions use this new call
instead. The discoverer does now itself perform the cloning when
that is necessary.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Until now, we have only been supporting a fix MTU size of 1500 bytes
for all broadcast media, irrespective of their actual capability.
We now make the broadcast MTU adaptable to the carrying media, i.e.,
we use the smallest MTU supported by any of the interfaces attached
to TIPC.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Until now, we have been keeping track of the exact set of broadcast
destinations though the help structure tipc_node_map. This leads us to
have to maintain a whole infrastructure for supporting this, including
a pseudo-bearer and a number of functions to manipulate both the bearers
and the node map correctly. Apart from the complexity, this approach is
also limiting, as struct tipc_node_map only can support cluster local
broadcast if we want to avoid it becoming excessively large. We want to
eliminate this limitation, in order to enable introduction of scoped
multicast in the future.
A closer analysis reveals that it is unnecessary maintaining this "full
set" overview; it is sufficient to keep a counter per bearer, indicating
how many nodes can be reached via this bearer at the moment. The protocol
is now robust enough to handle transitional discrepancies between the
nominal number of reachable destinations, as expected by the broadcast
protocol itself, and the number which is actually reachable at the
moment. The initial broadcast synchronization, in conjunction with the
retransmission mechanism, ensures that all packets will eventually be
acknowledged by the correct set of destinations.
This commit introduces these changes.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a link is taken down because of a node local event, such as
disabling of a bearer or an interface, we currently leave it to the
peer node to discover the broken communication. The default time for
such failure discovery is 1.5-2 seconds.
If we instead allow the terminating link endpoint to send out a RESET
message at the moment it is reset, we can achieve the impression that
both endpoints are going down instantly. Since this is a very common
scenario, we find it worthwhile to make this small modification.
Apart from letting the link produce the said message, we also have to
ensure that the interface is able to transmit it before TIPC is
detached. We do this by performing the disabling of a bearer in three
steps:
1) Disable reception of TIPC packets from the interface in question.
2) Take down the links, while allowing them so send out a RESET message.
3) Disable transmission of TIPC packets on the interface.
Apart from this, we now have to react on the NETDEV_GOING_DOWN event,
instead of as currently the NEDEV_DOWN event, to ensure that such
transmission is possible during the teardown phase.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In line with our effort to let the node level have full control over
its links, we want to move all link reset calls from link.c to node.c.
Some of the calls can be moved by simply moving the calling function,
when this is the right thing to do. For the remaining calls we use
the now established technique of returning a TIPC_LINK_DOWN_EVT
flag from tipc_link_rcv(), whereafter we perform the reset call when
the call returns.
This change serves as a preparation for the coming commits.
Tested-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, message sending is performed through a deep call chain,
where the node spinlock is grabbed and held during a significant
part of the transmission time. This is clearly detrimental to
overall throughput performance; it would be better if we could send
the message after the spinlock has been released.
In this commit, we do instead let the call revert on the stack after
the buffer chain has been added to the transmission queue, whereafter
clones of the buffers are transmitted to the device layer outside the
spinlock scope.
As a further step in our effort to separate the roles of the node
and link entities we also move the function tipc_link_xmit() to
node.c, and rename it to tipc_node_xmit().
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 4b475e3f2f8e4e241de101c8240f1d74d0470494
("tipc: eliminate delayed link deletion at link failover") the extra
boolean parameter "shutting_down" is not any longer needed for the
functions bearer_disable() and tipc_link_delete_list().
Furhermore, the function tipc_link_reset_links(), called from
bearer_reset() is now unnecessary. We can just as well delete
all the links, as we do in bearer_disable(), and start over with
creating new links.
This commit introduces those changes.
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Default link properties can be set for media or bearer. This
functionality was missed when introducing the NL compatibility layer.
This patch implements this functionality in the compat netlink
layer. It works the same way as it did in the old API. We search for
media and bearers matching the "link name". If we find a matching
media or bearer the link tolerance, priority or window is used as
default for new links on that media or bearer.
Fixes: 37e2d4843f9e (tipc: convert legacy nl link prop set to nl compat)
Reported-by: Tomi Ollila <tomi.ollila@iki.fi>
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NLM_F_MULTI must be used only when a NLMSG_DONE message is sent. In fact,
it is sent only at the end of a dump.
Libraries like libnl will wait forever for NLMSG_DONE.
Fixes: 35b9dd7607f0 ("tipc: add bearer get/dump to new netlink api")
Fixes: 7be57fc69184 ("tipc: add link get/dump to new netlink api")
Fixes: 46f15c6794fb ("tipc: add media get/dump to new netlink api")
CC: Richard Alpe <richard.alpe@ericsson.com>
CC: Jon Maloy <jon.maloy@ericsson.com>
CC: Ying Xue <ying.xue@windriver.com>
CC: tipc-discussion@lists.sourceforge.net
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit afaa3f65f65fda2e7b190aac7e2a75d9a2a77cb6
(tipc: purge links when bearer is disabled) was an attempt to resolve
a problem that turned out to have a more profound reason.
When we disable a bearer, we delete all its pertaining links if
there is no other bearer to perform failover to, or if the module
is shutting down. In case there are dual bearers, we wait with
deleting links until the failover procedure is finished.
However, this misses the case when a link on the removed bearer
was already down, so that there will be no failover procedure to
finish the link delete. This causes confusion if a new bearer is
added to replace the removed one, and also entails a small memory
leak.
This commit takes the current state of the link into account when
deciding when to delete it, and also reverses the above-mentioned
commit.
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
GhantaKrishnamurthy MohanKrishna
Jon Maloy
David S. Miller
Ying Xue
Tommi Rantala
Kleber Sacilotto de Souza
Parthasarathy Bhuvaragan
Johannes Berg
Michal Kubeček
Richard Alpe
Wei Yongjun
Nicolas Dichtel