| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
According to the link FSM, a received traffic packet can take a link
from state ESTABLISHING to ESTABLISHED, but the link can still not be
fully set up in one atomic operation. This means that even if the the
very first packet on the link is a traffic packet with sequence number
1 (one), it has to be dropped and retransmitted.
This can be avoided if we let the mentioned packet be preceded by a
LINK_PROTOCOL/STATE message, which takes up the endpoint before the
arrival of the traffic.
We add this small feature in this commit.
This is a fully compatible change.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In some link establishment scenarios we see that packet #2 may be sent
out before packet #1, forcing the receiver to demand retransmission of
the missing packet. This is harmless, but may cause confusion among
people tracing the packet flow.
Since this is extremely easy to fix, we do so by adding en extra send
call to the bearer immediately after the link has come up.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function tipc_link_timeout() is unnecessary complex, and can
easily be made more readable.
We do that with this commit. The only functional change is that we
remove a redundant test for whether the broadcast link is up or not.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a link is down, it will continuously try to re-establish contact
with the peer by sending out a RESET or an ACTIVATE message at each
timeout interval. The default value for this interval is currently
375 ms. This is wasteful, and may become a problem in very large
clusters with dozens or hundreds of nodes being down simultaneously.
We now introduce a simple backoff algorithm for these cases. The
first five messages are sent at default rate; thereafter a message
is sent only each 16th timer interval.
This will cover the vast majority of link recycling cases, since the
endpoint starting last will transmit at the higher speed, and the link
should normally be established well be before the rate needs to be
reduced.
The only case where we will see a degradation of link re-establishment
times is when the endpoints remain intact, and a glitch in the
transmission media is causing the link reset. We will then experience
a worst-case re-establishing time of 6 seconds, something we deem
acceptable.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a link endpoint is going down locally, e.g., because its interface
is being stopped, it will spontaneously send out a RESET message to
its peer, informing it about this fact. This saves the peer from
detecting the failure via probing, and hence gives both speedier and
less resource consuming failure detection on the peer side.
According to the link FSM, a receiver of a RESET message, ignoring the
reason for it, must now consider the sender ready to come back up, and
starts periodically sending out ACTIVATE messages to the peer in order
to re-establish the link. Also, according to the FSM, the receiver of
an ACTIVATE message can now go directly to state ESTABLISHED and start
sending regular traffic packets. This is a well-proven and robust FSM.
However, in the case of a reboot, there is a small possibilty that link
endpoint on the rebooted node may have been re-created with a new bearer
identity between the moment it sent its (pre-boot) RESET and the moment
it receives the ACTIVATE from the peer. The new bearer identity cannot
be known by the peer according to this scenario, since traffic headers
don't convey such information. This is a problem, because both endpoints
need to know the correct value of the peer's bearer id at any moment in
time in order to be able to produce correct link events for their users.
The only way to guarantee this is to enforce a full setup message
exchange (RESET + ACTIVATE) even after the reboot, since those messages
carry the bearer idientity in their header.
In this commit we do this by introducing and setting a "stopping" bit in
the header of the spontaneously generated RESET messages, informing the
peer that the sender will not be immediately ready to re-establish the
link. A receiver seeing this bit must act as if this were a locally
detected connectivity failure, and hence has to go through a full two-
way setup message exchange before any link can be re-established.
Although never reported, this problem seems to have always been around.
This protocol addition is fully backwards compatible.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Until now, the requests sent to topology server are queued
to a workqueue by the generic server framework.
These messages are processed by worker threads and trigger the
registered callbacks.
To reduce latency on uniprocessor systems, explicit rescheduling
is performed using cond_resched() after MAX_RECV_MSG_COUNT(25)
messages.
This implementation on SMP systems leads to an subscriber refcnt
error as described below:
When a worker thread yields by calling cond_resched() in a SMP
system, a new worker is created on another CPU to process the
pending workitem. Sometimes the sleeping thread wakes up before
the new thread finishes execution.
This breaks the assumption on ordering and being single threaded.
The fault is more frequent when MAX_RECV_MSG_COUNT is lowered.
If the first thread was processing subscription create and the
second thread processing close(), the close request will free
the subscriber and the create request oops as follows:
[31.224137] WARNING: CPU: 2 PID: 266 at include/linux/kref.h:46 tipc_subscrb_rcv_cb+0x317/0x380 [tipc]
[31.228143] CPU: 2 PID: 266 Comm: kworker/u8:1 Not tainted 4.5.0+ #97
[31.228377] Workqueue: tipc_rcv tipc_recv_work [tipc]
[...]
[31.228377] Call Trace:
[31.228377] [<ffffffff812fbb6b>] dump_stack+0x4d/0x72
[31.228377] [<ffffffff8105a311>] __warn+0xd1/0xf0
[31.228377] [<ffffffff8105a3fd>] warn_slowpath_null+0x1d/0x20
[31.228377] [<ffffffffa0098067>] tipc_subscrb_rcv_cb+0x317/0x380 [tipc]
[31.228377] [<ffffffffa00a4984>] tipc_receive_from_sock+0xd4/0x130 [tipc]
[31.228377] [<ffffffffa00a439b>] tipc_recv_work+0x2b/0x50 [tipc]
[31.228377] [<ffffffff81071925>] process_one_work+0x145/0x3d0
[31.246554] ---[ end trace c3882c9baa05a4fd ]---
[31.248327] BUG: spinlock bad magic on CPU#2, kworker/u8:1/266
[31.249119] BUG: unable to handle kernel NULL pointer dereference at 0000000000000428
[31.249323] IP: [<ffffffff81099d0c>] spin_dump+0x5c/0xe0
[31.249323] PGD 0
[31.249323] Oops: 0000 [#1] SMP
In this commit, we
- rename tipc_conn_shutdown() to tipc_conn_release().
- move connection release callback execution from tipc_close_conn()
to a new function tipc_sock_release(), which is executed before
we free the connection.
Thus we release the subscriber during connection release procedure
rather than connection shutdown procedure.
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We remove a couple of leftover fields in struct tipc_bearer. Those
were used by the old broadcast implementation, and are not needed
any longer. There is no functional changes in this commit.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Resetting a bearer/interface, with the consequence of resetting all its
pertaining links, is not an atomic action. This becomes particularly
evident in very large clusters, where a lot of traffic may happen on the
remaining links while we are busy shutting them down. In extreme cases,
we may even see links being re-created and re-established before we are
finished with the job.
To solve this, we now introduce a solution where we temporarily detach
the bearer from the interface when the bearer is reset. This inhibits
all packet reception, while sending still is possible. For the latter,
we use the fact that the device's user pointer now is zero to filter out
which packets can be sent during this situation; i.e., outgoing RESET
messages only. This filtering serves to speed up the neighbors'
detection of the loss event, and saves us from unnecessary probing.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When enabling a bearer we create a 'neigbor discoverer' instance by
calling the function tipc_disc_create() before the bearer is actually
registered in the list of enabled bearers. Because of this, the very
first discovery broadcast message, created by the mentioned function,
is lost, since it cannot find any valid bearer to use. Furthermore,
the used send function, tipc_bearer_xmit_skb() does not free the given
buffer when it cannot find a bearer, resulting in the leak of exactly
one send buffer each time a bearer is enabled.
This commit fixes this problem by introducing two changes:
1) Instead of attemting to send the discovery message directly, we let
tipc_disc_create() return the discovery buffer to the calling
function, tipc_enable_bearer(), so that the latter can send it
when the enabling sequence is finished.
2) In tipc_bearer_xmit_skb(), as well as in the two other transmit
functions at the bearer layer, we now free the indicated buffer or
buffer chain when a valid bearer cannot be found.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Expand headroom further in order to be able to fit the larger IPv6
header. Prior to this patch this caused a skb under panic for certain
tipc packets when using IPv6 UDP bearer(s).
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch extends udp_tunnel6_xmit_skb() to pass in the IPv6 flow label
from call sites. Currently, there's no such option and it's always set to
zero when writing ip6_flow_hdr(). Add a label member to ip_tunnel_key, so
that flow-based tunnels via collect metadata frontends can make use of it.
vxlan and geneve will be converted to add flow label support separately.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several cases of overlapping changes, as well as one instance
(vxlan) of a bug fix in 'net' overlapping with code movement
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make the c files less cluttered and enable netlink attributes to be
shared between files.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Until now, we have kept a pre-allocated protocol message header
aggregated into struct tipc_link. Apart from adding unnecessary
footprint to the link instances, this requires extra code both to
initialize and re-initialize it.
We now remove this sub-optimization. This change also makes it
possible to clean up the function tipc_build_proto_msg() and remove
a couple of small functions that were accessing the mentioned header.
In particular, we can replace all occurrences of the local function
call link_own_addr(link) with the generic tipc_own_addr(net).
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 4d5cfcba2f6e ('tipc: fix connection abort during subscription
cancel'), removes the check for a valid subscription before calling
tipc_nametbl_subscribe().
This will lead to a nullptr exception when we process a
subscription cancel request. For a cancel request, a null
subscription is passed to tipc_nametbl_subscribe() resulting
in exception.
In this commit, we call tipc_nametbl_subscribe() only for
a valid subscription.
Fixes: 4d5cfcba2f6e ('tipc: fix connection abort during subscription cancel')
Reported-by: Anders Widell <anders.widell@ericsson.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure the user has provided a scope for multicast and link local
addresses used locally by a UDP bearer.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The netlink policy for TIPC_NLA_UDP_LOCAL and TIPC_NLA_UDP_REMOTE
is of type binary with a defined length. This causes the policy
framework to threat the defined length as maximum length.
There is however no protection against a user sending a smaller
amount of data. Prior to this patch this wasn't handled which could
result in a partially incomplete sockaddr_storage struct containing
uninitialized data.
In this patch we use nla_memcpy() when copying the user data. This
ensures a potential gap at the end is cleared out properly.
This was found by Julia with Coccinelle tool.
Reported-by: Daniel Borkmann <daniel@iogearbox.net>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure we have a link before checking if it has been reset or not.
Prior to this patch tipc_link_is_reset() could be called with a non
existing link, resulting in a null pointer dereference.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prior to this patch enabling a IPv4 UDP bearer caused a null pointer
dereference in iptunnel_xmit_stats(), when it tried to dereference the
net device from the skb. To resolve this we now point the skb device
to the net device resolved from the routing table.
Fixes: 039f50629b7f (ip_tunnel: Move stats update to iptunnel_xmit())
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
reverts commit 94153e36e709e ("tipc: use existing sk_write_queue for
outgoing packet chain")
In Commit 94153e36e709e, we assume that we fill & empty the socket's
sk_write_queue within the same lock_sock() session.
This is not true if the link is congested. During congestion, the
socket lock is released while we wait for the congestion to cease.
This implementation causes a nullptr exception, if the user space
program has several threads accessing the same socket descriptor.
Consider two threads of the same program performing the following:
Thread1 Thread2
-------------------- ----------------------
Enter tipc_sendmsg() Enter tipc_sendmsg()
lock_sock() lock_sock()
Enter tipc_link_xmit(), ret=ELINKCONG spin on socket lock..
sk_wait_event() :
release_sock() grab socket lock
: Enter tipc_link_xmit(), ret=0
: release_sock()
Wakeup after congestion
lock_sock()
skb = skb_peek(pktchain);
!! TIPC_SKB_CB(skb)->wakeup_pending = tsk->link_cong;
In this case, the second thread transmits the buffers belonging to
both thread1 and thread2 successfully. When the first thread wakeup
after the congestion it assumes that the pktchain is intact and
operates on the skb's in it, which leads to the following exception:
[2102.439969] BUG: unable to handle kernel NULL pointer dereference at 00000000000000d0
[2102.440074] IP: [<ffffffffa005f330>] __tipc_link_xmit+0x2b0/0x4d0 [tipc]
[2102.440074] PGD 3fa3f067 PUD 3fa6b067 PMD 0
[2102.440074] Oops: 0000 [#1] SMP
[2102.440074] CPU: 2 PID: 244 Comm: sender Not tainted 3.12.28 #1
[2102.440074] RIP: 0010:[<ffffffffa005f330>] [<ffffffffa005f330>] __tipc_link_xmit+0x2b0/0x4d0 [tipc]
[...]
[2102.440074] Call Trace:
[2102.440074] [<ffffffff8163f0b9>] ? schedule+0x29/0x70
[2102.440074] [<ffffffffa006a756>] ? tipc_node_unlock+0x46/0x170 [tipc]
[2102.440074] [<ffffffffa005f761>] tipc_link_xmit+0x51/0xf0 [tipc]
[2102.440074] [<ffffffffa006d8ae>] tipc_send_stream+0x11e/0x4f0 [tipc]
[2102.440074] [<ffffffff8106b150>] ? __wake_up_sync+0x20/0x20
[2102.440074] [<ffffffffa006dc9c>] tipc_send_packet+0x1c/0x20 [tipc]
[2102.440074] [<ffffffff81502478>] sock_sendmsg+0xa8/0xd0
[2102.440074] [<ffffffff81507895>] ? release_sock+0x145/0x170
[2102.440074] [<ffffffff815030d8>] ___sys_sendmsg+0x3d8/0x3e0
[2102.440074] [<ffffffff816426ae>] ? _raw_spin_unlock+0xe/0x10
[2102.440074] [<ffffffff81115c2a>] ? handle_mm_fault+0x6ca/0x9d0
[2102.440074] [<ffffffff8107dd65>] ? set_next_entity+0x85/0xa0
[2102.440074] [<ffffffff816426de>] ? _raw_spin_unlock_irq+0xe/0x20
[2102.440074] [<ffffffff8107463c>] ? finish_task_switch+0x5c/0xc0
[2102.440074] [<ffffffff8163ea8c>] ? __schedule+0x34c/0x950
[2102.440074] [<ffffffff81504e12>] __sys_sendmsg+0x42/0x80
[2102.440074] [<ffffffff81504e62>] SyS_sendmsg+0x12/0x20
[2102.440074] [<ffffffff8164aed2>] system_call_fastpath+0x16/0x1b
In this commit, we maintain the skb list always in the stack.
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
msg.dst_sk needs to be set up with a valid socket because some callbacks
later derive the netns from it.
Fixes: 263ea09084d172d ("Revert "genl: Add genlmsg_new_unicast() for unicast message allocation")
Reported-by: Jon Maloy <maloy@donjonn.com>
Bisected-by: Jon Maloy <maloy@donjonn.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the TIPC module is unloaded, we have identified a race condition
that allows a node reference counter to go to zero and the node instance
being freed before the node timer is finished with accessing it. This
leads to occasional crashes, especially in multi-namespace environments.
The scenario goes as follows:
CPU0:(node_stop) CPU1:(node_timeout) // ref == 2
1: if(!mod_timer())
2: if (del_timer())
3: tipc_node_put() // ref -> 1
4: tipc_node_put() // ref -> 0
5: kfree_rcu(node);
6: tipc_node_get(node)
7: // BOOM!
We now clean up this functionality as follows:
1) We remove the node pointer from the node lookup table before we
attempt deactivating the timer. This way, we reduce the risk that
tipc_node_find() may obtain a valid pointer to an instance marked
for deletion; a harmless but undesirable situation.
2) We use del_timer_sync() instead of del_timer() to safely deactivate
the node timer without any risk that it might be reactivated by the
timeout handler. There is no risk of deadlock here, since the two
functions never touch the same spinlocks.
3: We remove a pointless tipc_node_get() + tipc_node_put() from the
timeout handler.
Reported-by: Zhijiang Hu <huzhijiang@gmail.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Although we have never seen it happen, we have identified the
following problematic scenario when nodes are stopped and deleted:
CPU0: CPU1:
tipc_node_xxx() //ref == 1
tipc_node_put() //ref -> 0
tipc_node_find() // node still in table
tipc_node_delete()
list_del_rcu(n. list)
tipc_node_get() //ref -> 1, bad
kfree_rcu()
tipc_node_put() //ref to 0 again.
kfree_rcu() // BOOM!
We fix this by introducing use of the conditional kref_get_if_not_zero()
instead of kref_get() in the function tipc_node_find(). This eliminates
any risk of post-mortem access.
Reported-by: Zhijiang Hu <huzhijiang@gmail.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/phy/bcm7xxx.c
drivers/net/phy/marvell.c
drivers/net/vxlan.c
All three conflicts were cases of simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tipc_bcast_unlock need to be unlocked in error path.
Signed-off-by: Insu Yun <wuninsu@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit bb9b18fb55b0 ("genl: Add genlmsg_new_unicast() for
unicast message allocation")'.
Nothing wrong with it; its no longer needed since this was only for
mmapped netlink support.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Refactor tipc_node_xmit() to fail fast and fail early. Fix several
potential memory leaks in unexpected error paths.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit 5266698661401a ("tipc: let broadcast packet reception
use new link receive function") we introduced a new per-node
broadcast reception link instance. This link is created at the
moment the node itself is created. Unfortunately, the allocation
is done after the node instance has already been added to the node
lookup hash table. This creates a potential race condition, where
arriving broadcast packets are able to find and access the node
before it has been fully initialized, and before the above mentioned
link has been created. The result is occasional crashes in the function
tipc_bcast_rcv(), which is trying to access the not-yet existing link.
We fix this by deferring the addition of the node instance until after
it has been fully initialized in the function tipc_node_create().
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Until now, tipc_rcv and tipc_send workqueues in server are allocated
with parameters WQ_UNBOUND & max_active = 1.
This parameters passed to this function makes it equivalent to
alloc_ordered_workqueue(). The later form is more explicit and
can inherit future ordered_workqueue changes.
In this commit we replace alloc_workqueue() with more readable
alloc_ordered_workqueue().
Acked-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Until now, we create timers even for the subscription requests
with timeout = TIPC_WAIT_FOREVER.
This can be improved by avoiding timer creation when the timeout
is set to TIPC_WAIT_FOREVER.
In this commit, we introduce a check to creates timers only
when timeout != TIPC_WAIT_FOREVER.
Acked-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Until now, during subscription creation the mod_time() &
tipc_subscrb_get() are called after releasing the subscriber
spin lock.
In a SMP system when performing a subscription creation, if the
subscription timeout occurs simultaneously (the timer is
scheduled to run on another CPU) then the timer thread
might decrement the subscribers refcount before the create
thread increments the refcount.
This can be simulated by creating subscription with timeout=0 and
sometimes the timeout occurs before the create request is complete.
This leads to the following message:
[30.702949] BUG: spinlock bad magic on CPU#1, kworker/u8:3/87
[30.703834] general protection fault: 0000 [#1] SMP
[30.704826] CPU: 1 PID: 87 Comm: kworker/u8:3 Not tainted 4.4.0-rc8+ #18
[30.704826] Workqueue: tipc_rcv tipc_recv_work [tipc]
[30.704826] task: ffff88003f878600 ti: ffff88003fae0000 task.ti: ffff88003fae0000
[30.704826] RIP: 0010:[<ffffffff8109196c>] [<ffffffff8109196c>] spin_dump+0x5c/0xe0
[...]
[30.704826] Call Trace:
[30.704826] [<ffffffff81091a16>] spin_bug+0x26/0x30
[30.704826] [<ffffffff81091b75>] do_raw_spin_lock+0xe5/0x120
[30.704826] [<ffffffff81684439>] _raw_spin_lock_bh+0x19/0x20
[30.704826] [<ffffffffa0096f10>] tipc_subscrb_rcv_cb+0x1d0/0x330 [tipc]
[30.704826] [<ffffffffa00a37b1>] tipc_receive_from_sock+0xc1/0x150 [tipc]
[30.704826] [<ffffffffa00a31df>] tipc_recv_work+0x3f/0x80 [tipc]
[30.704826] [<ffffffff8106a739>] process_one_work+0x149/0x3c0
[30.704826] [<ffffffff8106aa16>] worker_thread+0x66/0x460
[30.704826] [<ffffffff8106a9b0>] ? process_one_work+0x3c0/0x3c0
[30.704826] [<ffffffff8106a9b0>] ? process_one_work+0x3c0/0x3c0
[30.704826] [<ffffffff8107029d>] kthread+0xed/0x110
[30.704826] [<ffffffff810701b0>] ? kthread_create_on_node+0x190/0x190
[30.704826] [<ffffffff81684bdf>] ret_from_fork+0x3f/0x70
In this commit,
1. we remove the check for the return code for mod_timer()
2. we protect tipc_subscrb_get() using the subscriber spin lock.
We increment the subscriber's refcount as soon as we add the
subscription to subscriber's subscription list.
Acked-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Until now, while creating a subscription the subscriber lock
protects only the subscribers subscription list and not the
nametable. The call to tipc_nametbl_subscribe() is outside
the lock. However, at subscription timeout and cancel both
the subscribers subscription list and the nametable are
protected by the subscriber lock.
This asymmetric locking mechanism leads to the following problem:
In a SMP system, the timer can be fire on another core before
the create request is complete.
When the timer thread calls tipc_nametbl_unsubscribe() before create
thread calls tipc_nametbl_subscribe(), we get a nullptr exception.
This can be simulated by creating subscription with timeout=0 and
sometimes the timeout occurs before the create request is complete.
The following is the oops:
[57.569661] BUG: unable to handle kernel NULL pointer dereference at (null)
[57.577498] IP: [<ffffffffa02135aa>] tipc_nametbl_unsubscribe+0x8a/0x120 [tipc]
[57.584820] PGD 0
[57.586834] Oops: 0002 [#1] SMP
[57.685506] CPU: 14 PID: 10077 Comm: kworker/u40:1 Tainted: P OENX 3.12.48-52.27.1. 9688.1.PTF-default #1
[57.703637] Workqueue: tipc_rcv tipc_recv_work [tipc]
[57.708697] task: ffff88064c7f00c0 ti: ffff880629ef4000 task.ti: ffff880629ef4000
[57.716181] RIP: 0010:[<ffffffffa02135aa>] [<ffffffffa02135aa>] tipc_nametbl_unsubscribe+0x8a/ 0x120 [tipc]
[...]
[57.812327] Call Trace:
[57.814806] [<ffffffffa0211c77>] tipc_subscrp_delete+0x37/0x90 [tipc]
[57.821357] [<ffffffffa0211e2f>] tipc_subscrp_timeout+0x3f/0x70 [tipc]
[57.827982] [<ffffffff810618c1>] call_timer_fn+0x31/0x100
[57.833490] [<ffffffff81062709>] run_timer_softirq+0x1f9/0x2b0
[57.839414] [<ffffffff8105a795>] __do_softirq+0xe5/0x230
[57.844827] [<ffffffff81520d1c>] call_softirq+0x1c/0x30
[57.850150] [<ffffffff81004665>] do_softirq+0x55/0x90
[57.855285] [<ffffffff8105aa35>] irq_exit+0x95/0xa0
[57.860290] [<ffffffff815215b5>] smp_apic_timer_interrupt+0x45/0x60
[57.866644] [<ffffffff8152005d>] apic_timer_interrupt+0x6d/0x80
[57.872686] [<ffffffffa02121c5>] tipc_subscrb_rcv_cb+0x2a5/0x3f0 [tipc]
[57.879425] [<ffffffffa021c65f>] tipc_receive_from_sock+0x9f/0x100 [tipc]
[57.886324] [<ffffffffa021c826>] tipc_recv_work+0x26/0x60 [tipc]
[57.892463] [<ffffffff8106fb22>] process_one_work+0x172/0x420
[57.898309] [<ffffffff8107079a>] worker_thread+0x11a/0x3c0
[57.903871] [<ffffffff81077114>] kthread+0xb4/0xc0
[57.908751] [<ffffffff8151f318>] ret_from_fork+0x58/0x90
In this commit, we do the following at subscription creation:
1. set the subscription's subscriber pointer before performing
tipc_nametbl_subscribe(), as this value is required further in
the call chain ex: by tipc_subscrp_send_event().
2. move tipc_nametbl_subscribe() under the scope of subscriber lock
Acked-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Until now, the subscribers endianness for a subscription
create/cancel request is determined as:
swap = !(s->filter & (TIPC_SUB_PORTS | TIPC_SUB_SERVICE))
The checks are performed only for port/service subscriptions.
The swap calculation is incorrect if the filter in the subscription
cancellation request is set to TIPC_SUB_CANCEL (it's a malformed
cancel request, as the corresponding subscription create filter
is missing).
Thus, the check if the request is for cancellation fails and the
request is treated as a subscription create request. The
subscription creation fails as the request is illegal, which
terminates this connection.
In this commit we determine the endianness by including
TIPC_SUB_CANCEL, which will set swap correctly and the
request is processed as a cancellation request.
Acked-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In 'commit 7fe8097cef5f ("tipc: fix nullpointer bug when subscribing
to events")', we terminate the connection if the subscription
creation fails.
In the same commit, the subscription creation result was based on
the value of subscription pointer (set in the function) instead of
the return code.
Unfortunately, the same function also handles subscription
cancellation request. For a subscription cancellation request,
the subscription pointer cannot be set. Thus the connection is
terminated during cancellation request.
In this commit, we move the subcription cancel check outside
of tipc_subscrp_create(). Hence,
- tipc_subscrp_create() will create a subscripton
- tipc_subscrb_rcv_cb() will subscribe or cancel a subscription.
Fixes: 'commit 7fe8097cef5f ("tipc: fix nullpointer bug when subscribing to events")'
Acked-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In this commit, we split tipc_subscrp_create() into two:
1. tipc_subscrp_create() creates a subscription
2. A new function tipc_subscrp_subscribe() adds the
subscription to the subscriber subscription list,
activates the subscription timer and subscribes to
the nametable updates.
In future commits, the purpose of tipc_subscrb_rcv_cb() will
be to either subscribe or cancel a subscription.
There is no functional change in this commit.
Acked-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Until now, struct tipc_subscriber has duplicate fields for
type, upper and lower (as member of struct tipc_name_seq) at:
1. as member seq in struct tipc_subscription
2. as member seq in struct tipc_subscr, which is contained
in struct tipc_event
The former structure contains the type, upper and lower
values in network byte order and the later contains the
intact copy of the request.
The struct tipc_subscription contains a field swap to
determine if request needs network byte order conversion.
Thus by using swap, we can convert the request when
required instead of duplicating it.
In this commit,
1. we remove the references to these elements as members of
struct tipc_subscription and replace them with elements
from struct tipc_subscr.
2. provide new functions to convert the user request into
network byte order.
Acked-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Until now, struct tipc_subscription has duplicate timeout and filter
attributes present:
1. directly as members of struct tipc_subscription
2. in struct tipc_subscr, which is contained in struct tipc_event
In this commit, we remove the references to these elements as
members of struct tipc_subscription and replace them with elements
from struct tipc_subscr.
Acked-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Until now, during subscription creation we set sub->timeout by
converting the timeout request value in milliseconds to jiffies.
This is followed by setting the timeout value in the timer if
sub->timeout != TIPC_WAIT_FOREVER.
For a subscription create request with a timeout value of
TIPC_WAIT_FOREVER, msecs_to_jiffies(TIPC_WAIT_FOREVER)
returns MAX_JIFFY_OFFSET (0xfffffffe). This is not equal to
TIPC_WAIT_FOREVER (0xffffffff).
In this commit, we remove this check.
Acked-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently link priority changes isn't handled for active links. In
this patch we resolve this by changing our priority if the peer passes
a valid priority in a state message.
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Changing certain link attributes (link tolerance and link priority)
from the TIPC management tool is supposed to automatically take
effect at both endpoints of the affected link.
Currently the media address is not instantiated for the link and is
used uninstantiated when crafting protocol messages designated for the
peer endpoint. This means that changing a link property currently
results in the property being changed on the local machine but the
protocol message designated for the peer gets lost. Resulting in
property discrepancy between the endpoints.
In this patch we resolve this by using the media address from the
link entry and using the bearer transmit function to send it. Hence,
we can now eliminate the redundant function tipc_link_prot_xmit() and
the redundant field tipc_link::media_addr.
Fixes: 2af5ae372a4b (tipc: clean up unused code and structures)
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Reported-by: Jason Hu <huzhijiang@gmail.com>
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In 'commit 7fe8097cef5f ("tipc: fix nullpointer bug when subscribing
to events")', we terminate the connection if the subscription
creation fails.
In the same commit, the subscription creation result was based on
the value of the subscription pointer (set in the function) instead
of the return code.
Unfortunately, the same function tipc_subscrp_create() handles
subscription cancel request. For a subscription cancellation request,
the subscription pointer cannot be set. Thus if a subscriber has
several subscriptions and cancels any of them, the connection is
terminated.
In this commit, we terminate the connection based on the return value
of tipc_subscrp_create().
Fixes: commit 7fe8097cef5f ("tipc: fix nullpointer bug when subscribing to events")
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
By moving stats update into iptunnel_xmit(), we can simplify
iptunnel_xmit() usage. With this change there is no need to
call another function (iptunnel_xmit_stats()) to update stats
in tunnel xmit code path.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/renesas/ravb_main.c
kernel/bpf/syscall.c
net/ipv4/ipmr.c
All three conflicts were cases of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 5405ff6e15f40f2f ("tipc: convert node lock to rwlock")
introduced a bug to the node reference counter handling. When a
message is successfully sent in the function tipc_node_xmit(),
we return directly after releasing the node lock, instead of
continuing and decrementing the node reference counter as we
should do.
This commit fixes this bug.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The memory barrier in the helper wq_has_sleeper is needed by just
about every user of waitqueue_active. This patch generalises it
by making it take a wait_queue_head_t directly. The existing
helper is renamed to skwq_has_sleeper.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Coverity says:
*** CID 1338065: Error handling issues (CHECKED_RETURN)
/net/tipc/udp_media.c: 162 in tipc_udp_send_msg()
156 struct udp_media_addr *dst = (struct udp_media_addr *)&dest->value;
157 struct udp_media_addr *src = (struct udp_media_addr *)&b->addr.value;
158 struct sk_buff *clone;
159 struct rtable *rt;
160
161 if (skb_headroom(skb) < UDP_MIN_HEADROOM)
>>> CID 1338065: Error handling issues (CHECKED_RETURN)
>>> Calling "pskb_expand_head" without checking return value (as is done elsewhere 51 out of 56 times).
162 pskb_expand_head(skb, UDP_MIN_HEADROOM, 0, GFP_ATOMIC);
163
164 clone = skb_clone(skb, GFP_ATOMIC);
165 skb_set_inner_protocol(clone, htons(ETH_P_TIPC));
166 ub = rcu_dereference_rtnl(b->media_ptr);
167 if (!ub) {
When expanding buffer headroom over udp tunnel with pskb_expand_head(),
it's unfortunate that we don't check its return value. As a result, if
the function returns an error code due to the lack of memory, it may
cause unpredictable consequence as we unconditionally consider that
it's always successful.
Fixes: e53567948f82 ("tipc: conditionally expand buffer headroom over udp tunnel")
Reported-by: <scan-admin@coverity.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Even if we drain receive queue thoroughly in tipc_release() after tipc
socket is removed from rhashtable, it is possible that some packets
are in flight because some CPU runs receiver and did rhashtable lookup
before we removed socket. They will achieve receive queue, but nobody
delete them at all. To avoid this leak, we register a private socket
destructor to purge receive queue, meaning releasing packets pending
on receive queue will be delayed until the last reference of tipc
socket will be released.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 5266698661401afc5e ("tipc: let broadcast packet
reception use new link receive function") the broadcast send
link state was meant to always be set to LINK_ESTABLISHED, since
we don't need this link to follow the regular link FSM rules. It
was also the intention that this state anyway shouldn't impact
the run-time working state of the link, since the latter in
reality is controlled by the number of registered peers.
We have now discovered that this assumption is not quite correct.
If the broadcast link is reset because of too many retransmissions,
its state will inadvertently go to LINK_RESETTING, and never go
back to LINK_ESTABLISHED, because the LINK_FAILURE event was not
anticipated. This will work well once, but if it happens a second
time, the reset on a link in LINK_RESETTING has has no effect, and
neither the broadcast link nor the unicast links will go down as
they should.
Furthermore, it is confusing that the management tool shows that
this link is in UP state when that obviously isn't the case.
We now ensure that this state strictly follows the true working
state of the link. The state is set to LINK_ESTABLISHED when
the number of peers is non-zero, and to LINK_RESET otherwise.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The number of variables with Hungarian notation (l_ptr, n_ptr etc.)
has been significantly reduced over the last couple of years.
We now root out the last traces of this practice.
There are no functional changes in this commit.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We move the definition of struct tipc_link from link.h to link.c in
order to minimize its exposure to the rest of the code.
When needed, we define new functions to make it possible for external
entities to access and set data in the link.
Apart from the above, there are no functional changes.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Jon Paul Maloy
Parthasarathy Bhuvaragan
Richard Alpe
Daniel Borkmann
David S. Miller
Florian Westphal
Insu Yun
Pravin B Shelar
Herbert Xu
Ying Xue