| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
STA control register has areas of mode and opcodes for opeations. 18 bit is
using for mode selection, where 0 is old MIO/MDIO access method and 1 is
indirect access mode. 19-20 bits are using for setting up read/write
operation(STA opcodes). In current state 'read' is set into old MIO/MDIO mode
with 19 bit and write operation is set into 18 bit which is mode selection,
not a write operation. To correlate write with read we set it into 20 bit.
All those bit operations are MSB 0 based.
Signed-off-by: Ivan Mikhaylov <ivan@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
emac4syn chips has availability to use 8192 rx/tx fifo buffer sizes,
in current state if we set it up in dts 8192 as example, we will get
only 2048 which may impact on network speed.
Signed-off-by: Ivan Mikhaylov <ivan@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The code will try to access dev->iotlb when processing
VHOST_IOTLB_INVALIDATE even if it was not initialized which may lead
to NULL pointer dereference. Fixes this by check dev->iotlb before.
Fixes: 6b1e6cc7855b0 ("vhost: new device IOTLB API")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We used to call mutex_lock() in vhost_dev_lock_vqs() which tries to
hold mutexes of all virtqueues. This may confuse lockdep to report a
possible deadlock because of trying to hold locks belong to same
class. Switch to use mutex_lock_nested() to avoid false positive.
Fixes: 6b1e6cc7855b0 ("vhost: new device IOTLB API")
Reported-by: syzbot+dbb7c1161485e61b0241@syzkaller.appspotmail.com
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since TC block changes drivers are required to check if
the TC hw offload flag is set on the interface themselves.
Fixes: 2f4b411a3d67 ("i40e: Enable cloud filters via tc-flower")
Fixes: 44ae12a768b7 ("net: sched: move the can_offload check from binding phase to rule insertion phase")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Amritha Nambiar <amritha.nambiar@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes the typo CONFIG_CRYPTO_DES_SPARC64 => CONFIG_CRYPTO_CAMELLIA_SPARC64
Fixes: 81658ad0d923 ("sparc64: Add CAMELLIA driver making use of the new camellia opcodes.")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A tid was allocated for reserved MR during initialization but
not freed. This lead to an annoying output message during
rdma unload flow.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Double reservation for kernel dedicated dpi was performed.
Once in the core module and once in qedr.
Remove the reservation from core.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is needed to prevent sk_user_data being overwritten.
The check is done under the callback lock. This should prevent
a socket from being attached twice to a KCM mux. It also prevents
a socket from being attached for other use cases of sk_user_data
as long as the other cases set sk_user_data under the lock.
Followup work is needed to unify all the use cases of sk_user_data
to use the same locking.
Reported-by: syzbot+114b15f2be420a8886c3@syzkaller.appspotmail.com
Fixes: ab7ac4eb9832 ("kcm: Kernel Connection Multiplexor module")
Signed-off-by: Tom Herbert <tom@quantonium.net>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TCP sockets for IPv4 and IPv6 that are not listeners or in closed
stated are allowed to be attached to a KCM mux.
Fixes: ab7ac4eb9832 ("kcm: Kernel Connection Multiplexor module")
Reported-by: syzbot+8865eaff7f9acd593945@syzkaller.appspotmail.com
Signed-off-by: Tom Herbert <tom@quantonium.net>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update my email address.
Signed-off-by: James Morris <jmorris@namei.org>
|
|
TCF_LAYER_LINK and TCF_LAYER_NETWORK returned the same pointer as
skb->data points to the network header.
Use skb_mac_header instead.
Signed-off-by: Wolfgang Bumiller <w.bumiller@proxmox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
'ptr' is shifted by the offset and then validated,
the memcmp should not add it a second time.
Signed-off-by: Wolfgang Bumiller <w.bumiller@proxmox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We're seeing a raise of automated reports from testing tools and reports
about address leaks that are not really exploitable as-is, many of which
do not represent an immediate risk justifying to work in closed places.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This reverts commit 6cfb521ac0d5b97470883ff9b7facae264b7ab12.
Turns out distros do not want to make retpoline as part of their "ABI",
so this patch should not have been merged. Sorry Andi, this was my
fault, I suggested it when your original patch was the "correct" way of
doing this instead.
Reported-by: Jiri Kosina <jikos@kernel.org>
Fixes: 6cfb521ac0d5 ("module: Add retpoline tag to VERMAGIC")
Acked-by: Andi Kleen <ak@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: rusty@rustcorp.com.au
Cc: arjan.van.de.ven@intel.com
Cc: jeyu@kernel.org
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Driver periodically samples all neighbors configured in device
in order to update the kernel regarding their state. When finding
an entry configured in HW that doesn't show in neigh_lookup()
driver logs an error message.
This introduces a race when removing multiple neighbors -
it's possible that a given entry would still be configured in HW
as its removal is still being processed but is already removed
from the kernel's neighbor tables.
Simply remove the error message and gracefully accept such events.
Fixes: c723c735fa6b ("mlxsw: spectrum_router: Periodically update the kernel's neigh table")
Fixes: 60f040ca11b9 ("mlxsw: spectrum_router: Periodically dump active IPv6 neighbours")
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
with the introduction of commit
b0eb57cb97e7837ebb746404c2c58c6f536f23fa, it appears that rq->buf_info
is improperly handled. While it is heap allocated when an rx queue is
setup, and freed when torn down, an old line of code in
vmxnet3_rq_destroy was not properly removed, leading to rq->buf_info[0]
being set to NULL prior to its being freed, causing a memory leak, which
eventually exhausts the system on repeated create/destroy operations
(for example, when the mtu of a vmxnet3 interface is changed
frequently.
Fix is pretty straight forward, just move the NULL set to after the
free.
Tested by myself with successful results
Applies to net, and should likely be queued for stable, please
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-By: boyang@redhat.com
CC: boyang@redhat.com
CC: Shrikrishna Khare <skhare@vmware.com>
CC: "VMware, Inc." <pv-drivers@vmware.com>
CC: David S. Miller <davem@davemloft.net>
Acked-by: Shrikrishna Khare <skhare@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 513674b5a2c9 ("net: reevalulate autoflowlabel setting after
sysctl setting") removed the initialisation of
ipv6_pinfo::autoflowlabel and added a second flag to indicate
whether this field or the net namespace default should be used.
The getsockopt() handling for this case was not updated, so it
currently returns 0 for all sockets for which IPV6_AUTOFLOWLABEL is
not explicitly enabled. Fix it to return the effective value, whether
that has been set at the socket or net namespace level.
Fixes: 513674b5a2c9 ("net: reevalulate autoflowlabel setting after sysctl ...")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In pppoe_sendmsg(), reserving dev->hard_header_len bytes of headroom
was probably fine before the introduction of ->needed_headroom in
commit f5184d267c1a ("net: Allow netdevices to specify needed head/tailroom").
But now, virtual devices typically advertise the size of their overhead
in dev->needed_headroom, so we must also take it into account in
skb_reserve().
Allocation size of skb is also updated to take dev->needed_tailroom
into account and replace the arbitrary 32 bytes with the real size of
a PPPoE header.
This issue was discovered by syzbot, who connected a pppoe socket to a
gre device which had dev->header_ops->create == ipgre_header and
dev->hard_header_len == 0. Therefore, PPPoE didn't reserve any
headroom, and dev_hard_header() crashed when ipgre_header() tried to
prepend its header to skb->data.
skbuff: skb_under_panic: text:000000001d390b3a len:31 put:24
head:00000000d8ed776f data:000000008150e823 tail:0x7 end:0xc0 dev:gre0
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:104!
invalid opcode: 0000 [#1] SMP KASAN
Dumping ftrace buffer:
(ftrace buffer empty)
Modules linked in:
CPU: 1 PID: 3670 Comm: syzkaller801466 Not tainted
4.15.0-rc7-next-20180115+ #97
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
RIP: 0010:skb_panic+0x162/0x1f0 net/core/skbuff.c:100
RSP: 0018:ffff8801d9bd7840 EFLAGS: 00010282
RAX: 0000000000000083 RBX: ffff8801d4f083c0 RCX: 0000000000000000
RDX: 0000000000000083 RSI: 1ffff1003b37ae92 RDI: ffffed003b37aefc
RBP: ffff8801d9bd78a8 R08: 1ffff1003b37ae8a R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000000 R12: ffffffff86200de0
R13: ffffffff84a981ad R14: 0000000000000018 R15: ffff8801d2d34180
FS: 00000000019c4880(0000) GS:ffff8801db300000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000208bc000 CR3: 00000001d9111001 CR4: 00000000001606e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
skb_under_panic net/core/skbuff.c:114 [inline]
skb_push+0xce/0xf0 net/core/skbuff.c:1714
ipgre_header+0x6d/0x4e0 net/ipv4/ip_gre.c:879
dev_hard_header include/linux/netdevice.h:2723 [inline]
pppoe_sendmsg+0x58e/0x8b0 drivers/net/ppp/pppoe.c:890
sock_sendmsg_nosec net/socket.c:630 [inline]
sock_sendmsg+0xca/0x110 net/socket.c:640
sock_write_iter+0x31a/0x5d0 net/socket.c:909
call_write_iter include/linux/fs.h:1775 [inline]
do_iter_readv_writev+0x525/0x7f0 fs/read_write.c:653
do_iter_write+0x154/0x540 fs/read_write.c:932
vfs_writev+0x18a/0x340 fs/read_write.c:977
do_writev+0xfc/0x2a0 fs/read_write.c:1012
SYSC_writev fs/read_write.c:1085 [inline]
SyS_writev+0x27/0x30 fs/read_write.c:1082
entry_SYSCALL_64_fastpath+0x29/0xa0
Admittedly PPPoE shouldn't be allowed to run on non Ethernet-like
interfaces, but reserving space for ->needed_headroom is a more
fundamental issue that needs to be addressed first.
Same problem exists for __pppoe_xmit(), which also needs to take
dev->needed_headroom into account in skb_cow_head().
Fixes: f5184d267c1a ("net: Allow netdevices to specify needed head/tailroom")
Reported-by: syzbot+ed0838d0fa4c4f2b528e20286e6dc63effc7c14d@syzkaller.appspotmail.com
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With the addition of ORC unwinder and FRAME POINTER unwinder, the stack
trace skipping requirements have changed.
I went through the tracing stack trace dumps with ORC and with frame
pointers and recalculated the proper values.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
|
The function tracer can create a dynamically allocated trampoline that is
called by the function mcount or fentry hook that is used to call the
function callback that is registered. The problem is that the orc undwinder
will bail if it encounters one of these trampolines. This breaks the stack
trace of function callbacks, which include the stack tracer and setting the
stack trace for individual functions.
Since these dynamic trampolines are basically copies of the static ftrace
trampolines defined in ftrace_*.S, we do not need to create new orc entries
for the dynamic trampolines. Finding the return address on the stack will be
identical as the functions that were copied to create the dynamic
trampolines. When encountering a ftrace dynamic trampoline, we can just use
the orc entry of the ftrace static function that was copied for that
trampoline.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
|
Steven Rostedt discovered that the ftrace stack tracer is broken when
it's used with the ORC unwinder. The problem is that objtool is
instructed by the Makefile to ignore the ftrace_64.S code, so it doesn't
generate any ORC data for it.
Fix it by making the asm code objtool-friendly:
- Objtool doesn't like the fact that save_mcount_regs pushes RBP at the
beginning, but it's never restored (directly, at least). So just skip
the original RBP push, which is only needed for frame pointers anyway.
- Annotate some functions as normal callable functions with
ENTRY/ENDPROC.
- Add an empty unwind hint to return_to_handler(). The return address
isn't on the stack, so there's nothing ORC can do there. It will just
punt in the unlikely case it tries to unwind from that code.
With all that fixed, remove the OBJECT_FILES_NON_STANDARD Makefile
annotation so objtool can read the file.
Link: http://lkml.kernel.org/r/20180123040746.ih4ep3tk4pbjvg7c@treble
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
|
Assign true or false to boolean variables instead of an integer value.
This issue was detected with the help of Coccinelle.
Fixes: ffdb5211da1c ("xfrm: Auto-load xfrm offload modules")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
IPSec tunnel mode supports encapsulation of IPv4 over IPv6 and vice-versa.
The outer IP header is stripped and the inner IP inherits the original
Ethernet header. Tcpdump fails to properly decode the inner packet in
case that h_proto is different than the inner IP version.
Fix h_proto to reflect the inner IP version.
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
Commit bdcf0a423ea1 ("kernel: make groups_sort calling a responsibility
group_info allocators") appears to break nfsd rootsquash in a pretty
major way.
It adds a call to groups_sort() inside the loop that copies/squashes
gids, which means the valid gids are sorted along with the following
garbage. The net result is that the highest numbered valid gids are
replaced with any lower-valued garbage gids, possibly including 0.
We should sort only once, after filling in all the gids.
Fixes: bdcf0a423ea1 ("kernel: make groups_sort calling a responsibility ...")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Acked-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In orangefs_devreq_read, there is a loop which picks an op off the list
of pending ops. If the loop fails to find an op, there is nothing to
read, and it returns EAGAIN. If the op has been given up on, the loop
is restarted via a goto. The bug is that the variable which the found
op is written to is not reinitialized, so if there are no more eligible
ops on the list, the code runs again on the already handled op.
This is triggered by interrupting a process while the op is being copied
to the client-core. It's a fairly small window, but it's there.
Signed-off-by: Martin Brandenburg <martin@omnibond.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
set_op_state_purged can delete the op.
Signed-off-by: Martin Brandenburg <martin@omnibond.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The scatterlist is reused by both sendmsg and sendfile.
If a sendmsg of smaller number of pages is followed by a sendfile
of larger number of pages, the scatterlist may be too short, resulting
in a crash in gcm_encrypt.
Add sg_unmark_end to make the list the correct length.
tls_sw_sendmsg already calls sg_unmark_end correctly when it allocates
memory in alloc_sg, or in zerocopy_from_iter.
Signed-off-by: Dave Watson <davejwatson@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit 622190669403 ("be2net: Request RSS capability of Rx interface
depending on number of Rx rings") modified be_update_queues() so the
IFACE (HW representation of the netdevice) is destroyed and then
re-created. This causes a regression because potential promiscuous mode
is not restored properly during be_open() because the driver thinks
that the HW has promiscuous mode already enabled.
Note that Lancer is not affected by this bug because RX-filter flags are
disabled during be_close() for this chipset.
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Fixes: 622190669403 ("be2net: Request RSS capability of Rx interface depending on number of Rx rings")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit "net: igmp: Use correct source address on IGMPv3 reports"
introduced a check to validate the source address of locally generated
IGMPv3 packets.
Instead of checking the local interface address directly, it uses
inet_ifa_match(fl4->saddr, ifa), which checks if the address is on the
local subnet (or equal to the point-to-point address if used).
This breaks for point-to-point interfaces, so check against
ifa->ifa_local directly.
Cc: Kevin Cernekee <cernekee@chromium.org>
Fixes: a46182b00290 ("net: igmp: Use correct source address on IGMPv3 reports")
Reported-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Validate gso_type during segmentation as SKB_GSO_DODGY sources
may pass packets where the gso_type does not match the contents.
Syzkaller was able to enter the SCTP gso handler with a packet of
gso_type SKB_GSO_TCPV4.
On entry of transport layer gso handlers, verify that the gso_type
matches the transport protocol.
Fixes: 90017accff61 ("sctp: Add GSO support")
Link: http://lkml.kernel.org/r/<001a1137452496ffc305617e5fe0@google.com>
Reported-by: syzbot+fee64147a25aecd48055@syzkaller.appspotmail.com
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Without proper validation of DODGY packets, we might very well
feed qdisc_pkt_len_init() with invalid GSO packets.
tcp_hdrlen() might access out-of-bound data, so let's use
skb_header_pointer() and proper checks.
Whole story is described in commit d0c081b49137 ("flow_dissector:
properly cap thoff field")
We have the goal of validating DODGY packets earlier in the stack,
so we might very well revert this fix in the future.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Jason Wang <jasowang@redhat.com>
Reported-by: syzbot+9da69ebac7dddd804552@syzkaller.appspotmail.com
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In reset events in which our memory allocations need to be reallocated,
VPD data is being freed, but never reallocated. This can cause issues if
we later attempt to access that memory or reset and attempt to free the
memory. This patch moves the allocation of the VPD data to init_resources
so that it will be symmetrically freed during release resources.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we request an unsupported mtu value, the vnic server will suggest a
different value. Currently we take the suggested value without question
and login with that value. However, the behavior doesn't seem completely
sane as attempting to change the mtu to some specific value will change
the mtu to some completely different value most of the time. This patch
fixes the issue by logging in with the previously used mtu value and
printing an error message saying that the given mtu is unsupported.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using newer backing devices can cause the required padding at the end of
buffer as well as the number of queues to change after a failover.
Since we currently assume that these values never change, after a
failover to a backing device with different capabilities, we can get
errors from the vnic server, attempt to free long term buffers that are
no longer there, or not free long term buffers that should be freed.
This patch resolves the issue by checking whether any of these values
change, and if so perform the necessary re-allocations.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rds-tcp uses m_ack_seq to track the tcp ack# that indicates
that the peer has received a rds_message. The m_ack_seq is
used in rds_tcp_is_acked() to figure out when it is safe to
drop the rds_message from the RDS retransmit queue.
The m_ack_seq must be calculated as an offset from the right
edge of the in-flight tcp buffer, i.e., it should be based on
the ->write_seq, not the ->snd_nxt.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
That a kevent could not be scheduled is not an error.
Such handlers must be able to deal with multiple events anyway.
As the successful scheduling of a work is a debug event, make
the failure debug priority, too.
V2: coding style
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reported-by: Cristian Caravena <caravena@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't change endianness when assigning vlan value in cxgb4_tc_flower
code when processing flow match parameters. The value gets converted
to network order as part of filtering code in set_filter_wr.
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For ethtype_key = ETH_P_IPV6, set filter type as 1 in cxgb4_tc_flower
code when processing flow match parameters.
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The new helper would check if the pfn belongs to the page. For huge
pages it checks if the PFN is within range covered by the huge page.
The helper is used in check_pte(). The original code the helper replaces
had two call to page_to_pfn(). page_to_pfn() is relatively costly.
Although current GCC is able to optimize code to have one call, it's
better to do this explicitly.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Tetsuo reported random crashes under memory pressure on 32-bit x86
system and tracked down to change that introduced
page_vma_mapped_walk().
The root cause of the issue is the faulty pointer math in check_pte().
As ->pte may point to an arbitrary page we have to check that they are
belong to the section before doing math. Otherwise it may lead to weird
results.
It wasn't noticed until now as mem_map[] is virtually contiguous on
flatmem or vmemmap sparsemem. Pointer arithmetic just works against all
'struct page' pointers. But with classic sparsemem, it doesn't because
each section memap is allocated separately and so consecutive pfns
crossing two sections might have struct pages at completely unrelated
addresses.
Let's restructure code a bit and replace pointer arithmetic with
operations on pfns.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-and-tested-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Acked-by: Michal Hocko <mhocko@suse.com>
Fixes: ace71a19cec5 ("mm: introduce page_vma_mapped_walk()")
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Helmut reported a bug about division by zero while
running traffic and doing physical cable pull test.
When the cable unplugged the ppms become zero, so when
dividing the current ppms by the previous ppms in the
next dim iteration there is division by zero.
This patch prevent this division for both ppms and epms.
Fixes: c3164d2fc48f ("net/mlx5e: Added BW check for DIM decision mechanism")
Reported-by: Helmut Grauer <helmut.grauer@de.ibm.com>
Signed-off-by: Talat Batheesh <talatb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
Commit bacf6b499e11 ("x86/mm: Use a struct to reduce parameters for SME
PGD mapping") moved some parameters into a structure.
The structure was large enough to trigger the stack protection canary in
sme_encrypt_kernel which doesn't work this early, causing reboots.
Mark sme_encrypt_kernel appropriately to not use the canary.
Fixes: bacf6b499e11 ("x86/mm: Use a struct to reduce parameters for SME PGD mapping")
Signed-off-by: Laura Abbott <labbott@redhat.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The conversion of the alpha architecture PCI host bridge legacy IRQ
mapping/swizzling to the new PCI host bridge map/swizzle hooks carried
out through:
commit 0e4c2eeb758a ("alpha/PCI: Replace pci_fixup_irqs() call with
host bridge IRQ mapping hooks")
implies that IRQ for devices are now allocated through pci_assign_irq()
function in pci_device_probe() that is called when a driver matching a
device is found in order to probe the device through the device driver.
Alpha noname platforms required IRQ level programming to be executed
in sio_fixup_irq_levels(), that is called in noname_init_pci(), a
platform hook called within a subsys_initcall.
In noname_init_pci(), present IRQs are detected through
sio_collect_irq_levels() that check the struct pci_dev->irq number
to detect if an IRQ has been allocated for the device.
By the time sio_collect_irq_levels() is called, some devices may still
have not a matching driver loaded to match them (eg loadable module)
therefore their IRQ allocation is still pending - which means that
sio_collect_irq_levels() does not programme the correct IRQ level for
those devices, causing their IRQ handling to be broken when the device
driver is actually loaded and the device is probed.
Fix the issue by adding code in the noname map_irq() function
(noname_map_irq()) that, whilst mapping/swizzling the IRQ line, it also
ensures that the correct IRQ level programming is executed at platform
level, fixing the issue.
Fixes: 0e4c2eeb758a ("alpha/PCI: Replace pci_fixup_irqs() call with
host bridge IRQ mapping hooks")
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org # 4.14
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Mikulas Patocka <mpatocka@redhat.com>
Cc: Meelis Roos <mroos@linux.ee>
Signed-off-by: Matt Turner <mattst88@gmail.com>
|
|
The new firmware interfaces for branch prediction behaviour changes
are transparently available for the guest. Nevertheless, there is
new state attached that should be migrated and properly resetted.
Provide a mechanism for handling reset, migration and VSIE.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
[Changed capability number to 152. - Radim]
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
Force __builtin_constant_p to evaluate whether the argument to atomic_add
& atomic_sub is constant in the front-end before optimisations which
can lead GCC to output a call to __bad_increment_for_ia64_fetch_and_add().
See GCC bugzilla 83653.
Signed-off-by: Jakub Jelinek <jakub@redhat.com>
Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Without this patch, I drown in a sea of unknown attribute warnings
Link: http://lkml.kernel.org/r/20180117024539.27354-1-willy@infradead.org
Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
do_task_stat() accesses IP and SP of a task without bumping reference
count of a stack (which became an entity with independent lifetime at
some point).
Steps to reproduce:
#include <stdio.h>
#include <sys/types.h>
#include <sys/stat.h>
#include <fcntl.h>
#include <sys/time.h>
#include <sys/resource.h>
#include <unistd.h>
#include <sys/wait.h>
int main(void)
{
setrlimit(RLIMIT_CORE, &(struct rlimit){});
while (1) {
char buf[64];
char buf2[4096];
pid_t pid;
int fd;
pid = fork();
if (pid == 0) {
*(volatile int *)0 = 0;
}
snprintf(buf, sizeof(buf), "/proc/%u/stat", pid);
fd = open(buf, O_RDONLY);
read(fd, buf2, sizeof(buf2));
close(fd);
waitpid(pid, NULL, 0);
}
return 0;
}
BUG: unable to handle kernel paging request at 0000000000003fd8
IP: do_task_stat+0x8b4/0xaf0
PGD 800000003d73e067 P4D 800000003d73e067 PUD 3d558067 PMD 0
Oops: 0000 [#1] PREEMPT SMP PTI
CPU: 0 PID: 1417 Comm: a.out Not tainted 4.15.0-rc8-dirty #2
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1.fc27 04/01/2014
RIP: 0010:do_task_stat+0x8b4/0xaf0
Call Trace:
proc_single_show+0x43/0x70
seq_read+0xe6/0x3b0
__vfs_read+0x1e/0x120
vfs_read+0x84/0x110
SyS_read+0x3d/0xa0
entry_SYSCALL_64_fastpath+0x13/0x6c
RIP: 0033:0x7f4d7928cba0
RSP: 002b:00007ffddb245158 EFLAGS: 00000246
Code: 03 b7 a0 01 00 00 4c 8b 4c 24 70 4c 8b 44 24 78 4c 89 74 24 18 e9 91 f9 ff ff f6 45 4d 02 0f 84 fd f7 ff ff 48 8b 45 40 48 89 ef <48> 8b 80 d8 3f 00 00 48 89 44 24 20 e8 9b 97 eb ff 48 89 44 24
RIP: do_task_stat+0x8b4/0xaf0 RSP: ffffc90000607cc8
CR2: 0000000000003fd8
John Ogness said: for my tests I added an else case to verify that the
race is hit and correctly mitigated.
Link: http://lkml.kernel.org/r/20180116175054.GA11513@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Reported-by: "Kohli, Gaurav" <gkohli@codeaurora.org>
Tested-by: John Ogness <john.ogness@linutronix.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Since kernel 4.9, the thread_info has been moved into task_struct, no
longer locates at the bottom of kernel stack.
See commits c65eacbe290b ("sched/core: Allow putting thread_info into
task_struct") and 15f4eae70d36 ("x86: Move thread_info into
task_struct").
Before fix:
(gdb) set $current = $lx_current()
(gdb) p $lx_thread_info($current)
$1 = {flags = 1470918301}
(gdb) p $current.thread_info
$2 = {flags = 2147483648}
After fix:
(gdb) p $lx_thread_info($current)
$1 = {flags = 2147483648}
(gdb) p $current.thread_info
$2 = {flags = 2147483648}
Link: http://lkml.kernel.org/r/20180118210159.17223-1-imxikangjie@gmail.com
Fixes: 15f4eae70d36 ("x86: Move thread_info into task_struct")
Signed-off-by: Xi Kangjie <imxikangjie@gmail.com>
Acked-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Kieran Bingham <kbingham@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
Ivan Mikhaylov
Jason Wang
Jakub Kicinski
Corentin Labbe
Michal Kalderon
Tom Herbert
James Morris
Wolfgang Bumiller
Willy Tarreau
Greg Kroah-Hartman
Yuval Mintz
Neil Horman
Ben Hutchings
Guillaume Nault
Steven Rostedt (VMware)
Josh Poimboeuf
Gustavo A. R. Silva
Yossi Kuperman
Martin Brandenburg
Dave Watson
Ivan Vecera
Felix Fietkau
Willem de Bruijn
Eric Dumazet
John Allen
Sowmini Varadhan
Oliver Neukum
Kumar Sanghvi
Kirill A. Shutemov
Talat Batheesh
Linus Torvalds
Laura Abbott
Lorenzo Pieralisi
Christian Borntraeger
Matthew Wilcox
Alexey Dobriyan
Xi Kangjie