aboutsummaryrefslogtreecommitdiffstats
path: root/net/x25/x25_dev.c (unfollow)
AgeCommit message (Collapse)AuthorFilesLines
2014-07-08r8152: increase the tx timeouthayeswang1-1/+1
When the system is too busy to complete the urb, the tx timout function would be called. This causes the other tx urbs would be killed, too. Increase the tx timeout to avoid it. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-08ipconfig: add static to local variableFabian Frederick1-1/+1
ic_dev_xid is only used in ipconfig.c Cc: "David S. Miller" <davem@davemloft.net> Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru> Cc: netdev@vger.kernel.org Signed-off-by: Fabian Frederick <fabf@skynet.be> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07amd-xgbe: Base AXI DMA cache settings on device treeLendacky, Thomas3-18/+37
The default cache operations for ARM64 were changed during 3.15. To use coherent operations a "dma-coherent" device tree property is required. If that property is not present in the device tree node then the non-coherent operations are assigned for the device. Add support to the amd-xgbe driver to assign the AXI DMA cache settings based on whether the "dma-coherent" property is present in the device node. If present, use settings that work with the caches. If not present, use settings that do not look at the caches. Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07amd-xgbe: Performance enhancementsLendacky, Thomas4-78/+100
This patch provides some general performance enhancements for the driver: - Modify the default coalescing settings (reduce usec, increase frames) - Change the AXI burst length to 256 bytes (default was 16 bytes which was smaller than a cache line) - Change the AXI cache settings to write-back/write-allocate which allocate cache entries for received packets during the DMA since the packet will be processed soon afterwards - Combine ioread/iowrite when disabling both the Tx and Rx interrupts - Change to processing the Tx/Rx channels in pairs - Only recycle the Rx descriptors when a threshold of dirty descriptors is reached Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07amd-xgbe: Call netif_napi_del on ndo_stop operationLendacky, Thomas1-3/+6
Currently the napi context is added using netif_napi_add each time the ndo_open operation is called. However, there is not a corresponding netif_napi_del call during the ndo_stop operation. If the device ndo_open operation was called more than once an infinite loop occurs during module unload. Add a call to netif_napi_del during the ndo_stop operation. Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07amd-xgbe: Clear the proper MTL interrupt registerLendacky, Thomas1-1/+1
When initializing the MTL interrupts the interrupt status register is written to instead of the interrupt enable register. Since no MTL interrupts are being enabled and the default state is for MTL interrupts to be disabled this did not cause a problem, but needs to be fixed to target the correct register. Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07amd-xgbe: Fix debugfs compatibility change with kstrtouintLendacky, Thomas1-2/+2
The initial change from sscanf to kstrtouint broke backward compatbility by using a base of "0" in the kstrtouint call. This allowed for entering decimal, hexadecimal or octal as input where previously the sscanf always interpreted the input as hexadecimal. Additionally, -EIO was returned on error prior to this change and now it is whatever the error value that is returned by kstrtouint. Change the base value of the kstrtouint from 0 to 16 and return -EIO on error. Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Reported-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07net: arcnet: Remove "#define bool int"Rasmus Villemoes1-7/+3
The header file include/linux/arcdevice.h #defines bool to int, if bool is not already #defined. However, the files which use that header file seem to rely on that #define (unconditionally) being in effect: the prototypes for the functions arcrimi_reset, com20020_reset, com90io_reset, com90xx_reset (whose addresses are assigned to the hw.reset member of struct arcnet_local) use int explicitly. Moreover, that #define is an accident waiting to happen (scenario: inclusion of arcdevice.h followed by inclusion of some header which declares function prototypes using bool). Also, #include <linux/types.h> must appear before #include <linux/arcdevice.h> (the compiler wouldn't like "typedef _Bool int"). Since none of the files using arcdevice.h declare variables of type "bool", the patch is actually quite simple, unlike the commit message. Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07enic: fix return values in enic_set_coalesceGovindarajulu Varadarajan2-17/+12
enic_set_coalesce() has two problems. * It should return -EINVAL and not -EOPNOTSUPP for invalid coalesce values. * In case of MSIX, enic_set_coalesce return error after applying requested coalescing setting partially. We should either apply all the setting requeste and return success or apply non and return error. * This patch also simplifies the algo. This was introduced by '7c2ce6e60f703 enic: Add support for adaptive interrupt coalescing' These changes were suggested by Ben Hutchings here http://www.spinics.net/lists/netdev/msg283972.html Also change enic driver version. Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07bonding: remove no longer relevant vlan warningsJiri Pirko1-7/+0
These warnings are no longer relevant. Even when last slave is removed, there is a valid address assigned to bond (random). The correct functionality of vlans is ensured by maintaining unicast list in vlan_sync_address(). Suggested-by: Jay Vosburgh <jay.vosburgh@canonical.com> Signed-off-by: Jiri Pirko <jiri@resnulli.us> Acked-by: Veaceslav Falico <vfalico@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07at86rf230: add new authorAlexander Aring1-0/+1
Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07at86rf230: add sleep cycle timingAlexander Aring1-1/+6
Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07at86rf230: add timing for channel switchAlexander Aring1-1/+7
Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07at86rf230: rework reset to trx_off state changeAlexander Aring1-1/+15
Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07at86rf230: rework state change and start/stopAlexander Aring1-59/+67
This patch removes the current synchron state change function and add a new function for a state assert. Change the start and stop callbacks to use this new synchron state change behaviour. It's a wrapper around the async state change function. Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07at86rf230: rework irq_pol settingAlexander Aring1-5/+2
This patch rework the irq_pol register setting for rising and falling interrupt settings only. The default behaviour should be rising flag. Also use IRQ_TYPE_* defines instead of IRQF_* defines. There is no functionality change but irq_get_trigger_type returns IRQ_TYPE_* defines. Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07at86rf230: move RX_SAFE_MODE setting to hw_initAlexander Aring1-5/+4
There is no need to set this bit in start callback which could be called more than once. Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07at86rf230: rework transmit and receive handlingAlexander Aring1-268/+571
This patch is a complete reimplementation of transmit and receive handling for the at86rf230 driver. It solves also six bugs: First: The RX_SAFE_MODE is enabled and the transceiver doesn't leave the receive state while the framebuffer isn't read by a CMD_FB command. This is useful to read out the frame and don't get into another receive or transmit state, otherwise the frame would be overwritten. The current driver do twice CMD_FB calls, the first one leaves this protection. Second: Sometimes the CRC calculation is correct and the length field is greater 127. The current mac802154 layer and filter of a at86rf2xx doesn't check on this and the kernel crashes. In this case the frame is corrupted, we send the whole receive buffer to the next layer which can be useful for sniffing. Thrid: There is a undocumented race condition. When we are go into the RX_AACK_ON state the transceiver could be changed into RX_AACK_BUSY state. This is a normal behaviour. In this case the transceiver received a SHR while assert wasn't finished. Fourth: It also handle some more "correct" state changes. In aret mode the transceiver need to go to TX_ON before the transceiver go into RX_AACK_ON. Fifth: The programming model [0] describes also a error handling in ARET mode if the trac status is different than zero. This is patch adds support for handling this. Sixth: In receive handling the transceiver should also get the trac status according [0]. The driver could use the trac status as error statistic handling, but the driver doesn't use this currently. There is maybe some timing behaviour or the read of this register change some transceiver states. In addition the irqworker is removed. Instead we do async spi calls and no scheduling is involved anymore. The transmit function is also asynchron but with a wait_for_completion handling. The mac802154 layer doesn't support asynchron transmit handling right now. The state change behaviour is now changes, before it was: 1. assert while(!STATE_TRANSITION_IN_PROGRESS) 2. state change 3. assert while(!STATE_TRANSITION_IN_PROGRESS) 4. assert once(wanted state != current state) Sometimes a unexcepted state change occurs when 4. assert was violated. The new state change behaviour is: 1. assert while(!STATE_TRANSITION_IN_PROGRESS) 2. state change 3. wait state change timing according datasheet 4. assert once(wanted state != current state) This behaviour is described in the at86rf231 software programming model [0]. The state change documentation in this programming guide should also valid for at86rf212 and at86rf233 chips. The transceiver don't do a FORCE_TX_ON while we want to transmit a PDU. The new behaviour is a TX_ON and wait a receiving time (tFrame + tPAck). If we are still in RX_AACK_BUSY then we transmit a FORCE_TX_ON as timeout handling. The different is that FORCE_TX_ON aborts receiving and TX_ON waits if RX_AACK_BUSY is finished. This should decrease the drop rate of packets. [0] http://www.atmel.com/Images/AVR2022_swpm231-2.0.zip Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07at86rf230: add support for at86rf23x desenseAlexander Aring1-4/+18
To set the CCA_ED_THRES register the calculation for at86rf23x is different than for at86rf212. This patch adds a new callback for this calculation in chip data struct. Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07at86rf230: remove is212 and add driver dataAlexander Aring1-23/+36
This patch adds a new at86rf2xx_chip_data structure which holds device specific attributes. Instead of runtime decisions "if (is212())" we set callbacks/attributes while device detection. Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07at86rf230: rework detect device handlingAlexander Aring1-107/+76
This patch drops the current lowlevel spi calls for the detect device function instead we handle this via regmap. Also put the detection of in a seperate function and set all device specific attributes while detection. Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07at86rf230: add regmap supportAlexander Aring2-105/+168
This patch adds regmap support for the at86rf230 driver and drop the lowlevel spi access functions and use the regmap access functions. Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07mac802154: at86rf230: add hw flags and merge opsAlexander Aring3-58/+102
This patch adds new mac802154 hw flags for transmit power, csma and listen before transmit (lbt). These flags indicates that the transceiver supports these features. If the flags are set and the driver doesn't implement the necessary functions, then ieee802154_register_device returns -ENOSYS "Function not implemented". This patch merges also all at86rf230 operations into one operations structure and set the right hw flags for the at86rf230 transceivers. Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07net: fec: fix missing kmalloc() failure check in fec_enet_alloc_buffers()Russell King1-6/+9
fec_enet_alloc_buffers() assumes that kmalloc() will never fail, which is an invalid assumption. Fix this by implementing a common error cleanup path, and use it to also clean up after failed bounce buffer allocation. Acked-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07net: fec: ensure fec_enet_free_buffers() properly cleans the ringsRussell King1-1/+6
Ensure that we do not double-free any allocations, and that any transmit skbuffs are properly freed when we clean up the rings. Acked-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07net: fec: clean up transmit descriptor setupRussell King1-15/+18
Avoid writing any state until we're certain we can proceed with the transmission: this avoids writing mapping error address values to the descriptors, or setting the skbuff pointer until we have successfully mapped the skb. Acked-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07net: fec: make rx skb handling more robustRussell King1-6/+11
Allocate, and then map the receive skb before writing any data to the ring descriptor or storing the skb. When freeing the receive ring entries, unmap and free the skb, and then clear the stored skb pointer. This means we have ring data and skb pointer in one of two states: either both fully setup, or nothing setup. This simplifies the cleanup, as we can use just the skb pointer to indicate whether the descriptor is setup, and thus avoids potentially calling dma_unmap_single() on a DMA error value. Acked-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07net: fec: remove useless fep->openedRussell King2-6/+0
napi_disable() waits until the NAPI processing has completed, and then prevents any further polls. At this point, the driver then clears fep->opened. The NAPI poll function uses this to stop processing in the receive path. Hence, it will never see this variable cleared, because the NAPI poll has to complete before it will be cleared. Therefore, this variable serves no purpose, so let's remove it. Acked-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07net: fec: stop the phy before shutting down the MACRussell King1-1/+4
When the network interface goes down, stop the phy to prevent further link up status changes before taking the MAC or netif sections down. This prevents further reception of link up events which could potentially call fec_restart(). Since phy_stop() takes the mutex which adjust_link() runs under, we also ensure that adjust_link() will not already be processing a link up event. We also need to do this when suspending as well - we don't want a mis-timed phy state change to restart the MAC after we have stopped it for suspend, and thus need to restart the phy when resuming. Acked-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07net: fec: ensure that a disconnected phy isn't configuredRussell King1-0/+4
When we disconnect from a phy, we should forget our pointer to it so we don't accidentally try to configure it. We handle a NULL phy pointer correctly in most places, except fec_enet_set_pauseparam(). Fix this too. Acked-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07net: fec: remove checking for NULL phy_dev in fec_enet_close()Russell King1-4/+2
fep->phy_dev can not be NULL here for two reasons: - fec_enet_open() will have successfully connected the phy, or will have failed. - fec_enet_open() will have called phy_start(fep->phy_dev), which unconditionally dereferences this pointer. If it were to be NULL here, then fec_enet_open() will have already oopsed. Acked-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07net: fec: use netif_tx_disable() rather than netif_stop_queue()Russell King1-2/+2
We use netif_stop_queue() in several places where we want to ensure that the start_xmit function is not running. netif_stop_queue() is not sufficient to achieve that - it merely sets a flag to indicate that the transmit queue(s) should not be run. netif_tx_disable() gives this guarantee, since it takes the transmit queue lock while marking the queue stopped. This will wait for the transmit function to complete before returning. Acked-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07net: fec: fix interrupt handling racesRussell King1-18/+22
While running: while :; do iperf -c <HOST> -P 4; done, transmit timeouts are regularly reported. With the tx ring dumping in place, we can see that all entries are in use, and the hardware has finished transmitting these packets. However, the driver has not reclaimed these ring entries. This can occur if the interrupt handler is invoked at the wrong moment - eg: CPU0 CPU1 fec_enet_tx() interrupt, IEVENT = FEC_ENET_TXF FEC_ENET_TXF cleared napi_schedule_prep() napi_complete() The result is that we clear the transmit interrupt, but we don't trigger any cleaning of the transmit ring. Instead, use a different strategy: - When receiving a transmit or receive interrupt, disable both tx and rx interrupts, but do not acknowledge them. Schedule a napi poll. Don't loop. - When we are polled, read IEVENT, acknowledging the pending transmit and receive interrupts, before then going on to process the appropriate rings. This allows us to avoid the race, and has a number of other advantages: - we cut down on the number of transmit interrupts we have to process. - we only look at the rings which have pending events. - we gain additional throughput: the iperf total bandwidth increases from about 180Mbps to 240Mbps: [ 3] 0.0-10.0 sec 68.1 MBytes 57.0 Mbits/sec [ 5] 0.0-10.0 sec 72.4 MBytes 60.5 Mbits/sec [ 4] 0.0-10.1 sec 76.1 MBytes 63.5 Mbits/sec [ 6] 0.0-10.1 sec 71.9 MBytes 59.9 Mbits/sec [SUM] 0.0-10.1 sec 288 MBytes 241 Mbits/sec Acked-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07net: fec: fix ethtool set_pauseparam duplex bugRussell King1-1/+1
Setting the pause parameters causes a running network interface to be restarted. However, the restart forces the FEC into half-duplex mode, whether or not the remote end is in half-duplex mode. Misconfigured duplex mode is a known source of problems on a link. Fix this by always preserving the duplex mode on configuration changes. Acked-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07net: fec: iMX6 FEC does not support half-duplex gigabitRussell King1-0/+1
The iMX6 gigabit FEC does not support half-duplex gigabit operation. Phys attacked to the FEC may support this, and we currently do nothing to disable this feature. This may result in an invalid configuration. Mask out phy support for gigabit half-duplex operation. Acked-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07net: Only do flow_dissector hash computation once per packetTom Herbert2-2/+9
Add sw_hash flag to skbuff to indicate that skb->hash was computed from flow_dissector. This flag is checked in skb_get_hash to avoid repeatedly trying to compute the hash (ie. in the case that no L4 hash can be computed). Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07ipv6: Implement automatic flow label generation on transmitTom Herbert11-6/+62
Automatically generate flow labels for IPv6 packets on transmit. The flow label is computed based on skb_get_hash. The flow label will only automatically be set when it is zero otherwise (i.e. flow label manager hasn't set one). This supports the transmit side functionality of RFC 6438. Added an IPv6 sysctl auto_flowlabels to enable/disable this behavior system wide, and added IPV6_AUTOFLOWLABEL socket option to enable this functionality per socket. By default, auto flowlabels are disabled to avoid possible conflicts with flow label manager, however if this feature proves useful we may want to enable it by default. It should also be noted that FreeBSD has already implemented automatic flow labels (including the sysctl and socket option). In FreeBSD, automatic flow labels default to enabled. Performance impact: Running super_netperf with 200 flows for TCP_RR and UDP_RR for IPv6. Note that in UDP case, __skb_get_hash will be called for every packet with explains slight regression. In the TCP case the hash is saved in the socket so there is no regression. Automatic flow labels disabled: TCP_RR: 86.53% CPU utilization 127/195/322 90/95/99% latencies 1.40498e+06 tps UDP_RR: 90.70% CPU utilization 118/168/243 90/95/99% latencies 1.50309e+06 tps Automatic flow labels enabled: TCP_RR: 85.90% CPU utilization 128/199/337 90/95/99% latencies 1.40051e+06 UDP_RR 92.61% CPU utilization 115/164/236 90/95/99% latencies 1.4687e+06 Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07flow_dissector: Use IPv6 flow label in flow_dissectorTom Herbert1-0/+17
This patch implements the receive side to support RFC 6438 which is to use the flow label as an ECMP hash. If an IPv6 flow label is set in a packet we can use this as input for computing an L4-hash. There should be no need to parse any transport headers in this case. Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07vxlan: Call udp_flow_src_portTom Herbert3-30/+3
In vxlan and OVS vport-vxlan call common function to get source port for a UDP tunnel. Removed vxlan_src_port since the functionality is now in udp_flow_src_port. Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07udp: Add function to make source port for UDP tunnelsTom Herbert1-0/+29
This patch adds udp_flow_src_port function which is intended to be a common function that UDP tunnel implementations call to set the source port. The source port is chosen so that a hash over the outer headers (IP addresses and UDP ports) acts as suitable hash for the flow of the encapsulated packet. In this manner, UDP encapsulation works with RSS and ECMP based wrt the inner flow. Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07net: Call skb_get_hash in get_xps_queue and __skb_tx_hashTom Herbert3-26/+7
Call standard function to get a packet hash instead of taking this from skb->sk->sk_hash or only using skb->protocol. Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07net: Save TX flow hash in sock and set in skbuf on xmitTom Herbert8-0/+50
For a connected socket we can precompute the flow hash for setting in skb->hash on output. This is a performance advantage over calculating the skb->hash for every packet on the connection. The computation is done using the common hash algorithm to be consistent with computations done for packets of the connection in other states where thers is no socket (e.g. time-wait, syn-recv, syn-cookies). This patch adds sk_txhash to the sock structure. inet_set_txhash and ip6_set_txhash functions are added which are called from points in TCP and UDP where socket moves to established state. skb_set_hash_from_sk is a function which sets skb->hash from the sock txhash value. This is called in UDP and TCP transmit path when transmitting within the context of a socket. Tested: ran super_netperf with 200 TCP_RR streams over a vxlan interface (in this case skb_get_hash called on every TX packet to create a UDP source port). Before fix: 95.02% CPU utilization 154/256/505 90/95/99% latencies 1.13042e+06 tps Time in functions: 0.28% skb_flow_dissect 0.21% __skb_get_hash After fix: 94.95% CPU utilization 156/254/485 90/95/99% latencies 1.15447e+06 Neither __skb_get_hash nor skb_flow_dissect appear in perf Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07flow_dissector: Abstract out hash computationTom Herbert2-16/+29
Move the hash computation located in __skb_get_hash to be a separate function which takes flow_keys as input. This will allow flow hash computation in other contexts where we only have addresses and ports. Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07net: systemport: add Wake-on-LAN supportFlorian Fainelli3-4/+166
Support for Wake-on-LAN using Magic Packet with or without SecureOn password is implemented doing the following: - setting the password to the relevant UniMAC registers - flagging the device as a wakeup source for the system, as well as its Wake-on-LAN interrupt - prepare the hardware for entering WoL mode - enabling the MPD interrupt to wake us The Device Tree binding documentation is also reflected to specify the third optional Wake-on-LAN interrupt line. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07net: systemport: rename rx_csum_en to rx_chk_enFlorian Fainelli2-6/+6
This boolean tells us whether we are using the RXCHK hardware block, so use a variable name that reflects that. RXCHK might be used in the future to implement Wake-on-LAN using ARP or unicast packets. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07net: systemport: add suspend and resume supportFlorian Fainelli1-4/+160
Implement the hardware recommended suspend/resume procedure for SYSTEMPORT. We leverage the previous factoring work such that we can logically break all suspend/resume operations into disctint RX and TX code paths. When the system enters S3, we will loose all register contents, so make sure that we correctly re-program all the hardware and software views of the RX & TX rings as well. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07net: systemport: add bcm_sysport_netif_{enable,stop}Florian Fainelli1-13/+27
Factor common code that either enables or disables the network interface with the networking stack. We are going to reuse these functions for suspend/resume callbacks. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07net: systemport: update umac_enable_set to take a bitmaskFlorian Fainelli1-12/+7
Quite often we need to enable either the transmitter or the receiver bits in UMAC_CMD, use umac_enable_set() to do that for us. This is a preliminary change to introduce suspend/resume support in the driver. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-076lowpan: mac802154: fix coding style issuesVarka Bhadram15-145/+153
This patch fixed the coding style issues reported by checkpatch.pl following issues fixed: CHECK: Alignment should match open parenthesis WARNING: line over 80 characters CHECK: Blank lines aren't necessary before a close brace '}' WARNING: networking block comments don't use an empty /* line, use /* Comment... WARNING: Missing a blank line after declarations WARNING: networking block comments start with * on subsequent lines CHECK: braces {} should be used on all arms of this statement Signed-off-by: Varka Bhadram <varkab@cdac.in> Tested-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07netlink: Fix do_one_broadcast() prototype.Rami Rosen1-9/+6
This patch changes the prototype of the do_one_broadcast() method so that it will return void. Signed-off-by: Rami Rosen <ramirose@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.